ath9k: Remove a few unused functions

ATH9K_ANT_VARIABLE is the default diversity control used.
Consequently ath9k_hw_decrease_chain_power() does nothing.
ath9k_hw_setantennaswitch() is unused too.

Also, gbeacon_rate is unused.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1 files changed, 0 insertions, 90 deletions

diff --git a/drivers/net/wireless/ath/ath9k/phy.c b/drivers/net/wireless/ath/ath9k/phy.c
index 13ab4d7eb7aa..c3b59390fe38 100644
--- a/drivers/net/wireless/ath/ath9k/phy.c
+++ b/drivers/net/wireless/ath/ath9k/phy.c
@@ -528,95 +528,6 @@ static void ath9k_hw_force_bias(struct ath_hw *ah, u16 synth_freq)
 }
 
 /**
- * ath9k_hw_decrease_chain_power()
- *
- * @ah: atheros hardware structure
- * @chan:
- *
- * Only used on the AR5416 and AR5418 with the external AR2133/AR5133 radios.
- *
- * Sets a chain internal RF path to the lowest output power. Any
- * further writes to bank6 after this setting will override these
- * changes. Thus this function must be the last function in the
- * sequence to modify bank 6.
- *
- * This function must be called after ar5416SetRfRegs() which is
- * called from ath9k_hw_process_ini() due to swizzling of bank 6.
- * Depends on ah->analogBank6Data being initialized by
- * ath9k_hw_set_rf_regs()
- *
- * Additional additive reduction in power -
- * change chain's switch table so chain's tx state is actually the rx
- * state value. May produce different results in 2GHz/5GHz as well as
- * board to board but in general should be a reduction.
- *
- * Activated by #ifdef ALTER_SWITCH.  Not tried yet.  If so, must be
- * called after ah->eep_ops->set_board_values() due to RMW of
- * PHY_SWITCH_CHAIN_0.
- */
-void ath9k_hw_decrease_chain_power(struct ath_hw *ah,
-				   struct ath9k_channel *chan)
-{
-	int i, regWrites = 0;
-	u32 bank6SelMask;
-	u32 *bank6Temp = ah->bank6Temp;
-
-	BUG_ON(AR_SREV_9280_10_OR_LATER(ah));
-
-	switch (ah->config.diversity_control) {
-	case ATH9K_ANT_FIXED_A:
-		bank6SelMask =
-		    (ah->config.antenna_switch_swap & ANTSWAP_AB) ?
-			REDUCE_CHAIN_0 : /* swapped, reduce chain 0 */
-			REDUCE_CHAIN_1; /* normal, select chain 1/2 to reduce */
-		break;
-	case ATH9K_ANT_FIXED_B:
-		bank6SelMask =
-		    (ah->config.antenna_switch_swap & ANTSWAP_AB) ?
-			REDUCE_CHAIN_1 : /* swapped, reduce chain 1/2 */
-			REDUCE_CHAIN_0; /* normal, select chain 0 to reduce */
-		break;
-	case ATH9K_ANT_VARIABLE:
-		return; /* do not change anything */
-		break;
-	default:
-		return; /* do not change anything */
-		break;
-	}
-
-	for (i = 0; i < ah->iniBank6.ia_rows; i++)
-		bank6Temp[i] = ah->analogBank6Data[i];
-
-	/* Write Bank 5 to switch Bank 6 write to selected chain only */
-	REG_WRITE(ah, AR_PHY_BASE + 0xD8, bank6SelMask);
-
-	/*
-	 * Modify Bank6 selected chain to use lowest amplification.
-	 * Modifies the parameters to a value of 1.
-	 * Depends on existing bank 6 values to be cached in
-	 * ah->analogBank6Data
-	 */
-	ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 189, 0);
-	ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 190, 0);
-	ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 191, 0);
-	ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 192, 0);
-	ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 193, 0);
-	ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 222, 0);
-	ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 245, 0);
-	ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 246, 0);
-	ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 247, 0);
-
-	REG_WRITE_RF_ARRAY(&ah->iniBank6, bank6Temp, regWrites);
-
-	REG_WRITE(ah, AR_PHY_BASE + 0xD8, 0x00000053);
-#ifdef ALTER_SWITCH
-	REG_WRITE(ah, PHY_SWITCH_CHAIN_0,
-		  (REG_READ(ah, PHY_SWITCH_CHAIN_0) & ~0x38)
-		  | ((REG_READ(ah, PHY_SWITCH_CHAIN_0) >> 3) & 0x38));
-#endif
-}
-
-/**
  * ath9k_hw_set_channel - tune to a channel on the external AR2133/AR5133 radios
  * @ah: atheros hardware stucture
  * @chan:
@@ -687,7 +598,6 @@ int ath9k_hw_set_channel(struct ath_hw *ah, struct ath9k_channel *chan)
 	}
 
 	ath9k_hw_force_bias(ah, freq);
-	ath9k_hw_decrease_chain_power(ah, chan);
 
 	reg32 =
 	    (channelSel << 8) | (aModeRefSel << 2) | (bModeSynth << 1) |