e1000e: sync change flow control variables with ixgbe

Sync flow control variables and usage model with that found in the ixgbe
driver.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 23 insertions, 23 deletions

diff --git a/drivers/net/e1000e/lib.c b/drivers/net/e1000e/lib.c
index 37753d13cd22..66741104ffd1 100644
--- a/drivers/net/e1000e/lib.c
+++ b/drivers/net/e1000e/lib.c
@@ -645,12 +645,12 @@ static s32 e1000_set_default_fc_generic(struct e1000_hw *hw)
 	}
 
 	if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 0)
-		hw->fc.type = e1000_fc_none;
+		hw->fc.requested_mode = e1000_fc_none;
 	else if ((nvm_data & NVM_WORD0F_PAUSE_MASK) ==
 		 NVM_WORD0F_ASM_DIR)
-		hw->fc.type = e1000_fc_tx_pause;
+		hw->fc.requested_mode = e1000_fc_tx_pause;
 	else
-		hw->fc.type = e1000_fc_full;
+		hw->fc.requested_mode = e1000_fc_full;
 
 	return 0;
 }
@@ -678,23 +678,23 @@ s32 e1000e_setup_link(struct e1000_hw *hw)
 		return 0;
 
 	/*
-	 * If flow control is set to default, set flow control based on
-	 * the EEPROM flow control settings.
+	 * If requested flow control is set to default, set flow control
+	 * based on the EEPROM flow control settings.
 	 */
-	if (hw->fc.type == e1000_fc_default) {
+	if (hw->fc.requested_mode == e1000_fc_default) {
 		ret_val = e1000_set_default_fc_generic(hw);
 		if (ret_val)
 			return ret_val;
 	}
 
 	/*
-	 * We want to save off the original Flow Control configuration just
-	 * in case we get disconnected and then reconnected into a different
-	 * hub or switch with different Flow Control capabilities.
+	 * Save off the requested flow control mode for use later.  Depending
+	 * on the link partner's capabilities, we may or may not use this mode.
 	 */
-	hw->fc.original_type = hw->fc.type;
+	hw->fc.current_mode = hw->fc.requested_mode;
 
-	hw_dbg(hw, "After fix-ups FlowControl is now = %x\n", hw->fc.type);
+	hw_dbg(hw, "After fix-ups FlowControl is now = %x\n",
+		hw->fc.current_mode);
 
 	/* Call the necessary media_type subroutine to configure the link. */
 	ret_val = mac->ops.setup_physical_interface(hw);
@@ -746,7 +746,7 @@ static s32 e1000_commit_fc_settings_generic(struct e1000_hw *hw)
 	 *	  do not support receiving pause frames).
 	 *      3:  Both Rx and Tx flow control (symmetric) are enabled.
 	 */
-	switch (hw->fc.type) {
+	switch (hw->fc.current_mode) {
 	case e1000_fc_none:
 		/* Flow control completely disabled by a software over-ride. */
 		txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
@@ -928,7 +928,7 @@ s32 e1000e_set_fc_watermarks(struct e1000_hw *hw)
 	 * ability to transmit pause frames is not enabled, then these
 	 * registers will be set to 0.
 	 */
-	if (hw->fc.type & e1000_fc_tx_pause) {
+	if (hw->fc.current_mode & e1000_fc_tx_pause) {
 		/*
 		 * We need to set up the Receive Threshold high and low water
 		 * marks as well as (optionally) enabling the transmission of
@@ -967,7 +967,7 @@ s32 e1000e_force_mac_fc(struct e1000_hw *hw)
 	 * receive flow control.
 	 *
 	 * The "Case" statement below enables/disable flow control
-	 * according to the "hw->fc.type" parameter.
+	 * according to the "hw->fc.current_mode" parameter.
 	 *
 	 * The possible values of the "fc" parameter are:
 	 *      0:  Flow control is completely disabled
@@ -978,9 +978,9 @@ s32 e1000e_force_mac_fc(struct e1000_hw *hw)
 	 *      3:  Both Rx and Tx flow control (symmetric) is enabled.
 	 *  other:  No other values should be possible at this point.
 	 */
-	hw_dbg(hw, "hw->fc.type = %u\n", hw->fc.type);
+	hw_dbg(hw, "hw->fc.current_mode = %u\n", hw->fc.current_mode);
 
-	switch (hw->fc.type) {
+	switch (hw->fc.current_mode) {
 	case e1000_fc_none:
 		ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
 		break;
@@ -1124,11 +1124,11 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 			 * ONLY. Hence, we must now check to see if we need to
 			 * turn OFF  the TRANSMISSION of PAUSE frames.
 			 */
-			if (hw->fc.original_type == e1000_fc_full) {
-				hw->fc.type = e1000_fc_full;
+			if (hw->fc.requested_mode == e1000_fc_full) {
+				hw->fc.current_mode = e1000_fc_full;
 				hw_dbg(hw, "Flow Control = FULL.\r\n");
 			} else {
-				hw->fc.type = e1000_fc_rx_pause;
+				hw->fc.current_mode = e1000_fc_rx_pause;
 				hw_dbg(hw, "Flow Control = "
 					 "RX PAUSE frames only.\r\n");
 			}
@@ -1146,7 +1146,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 			  (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
 			  (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
 			  (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
-			hw->fc.type = e1000_fc_tx_pause;
+			hw->fc.current_mode = e1000_fc_tx_pause;
 			hw_dbg(hw, "Flow Control = Tx PAUSE frames only.\r\n");
 		}
 		/*
@@ -1162,14 +1162,14 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 			 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
 			 !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
 			 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
-			hw->fc.type = e1000_fc_rx_pause;
+			hw->fc.current_mode = e1000_fc_rx_pause;
 			hw_dbg(hw, "Flow Control = Rx PAUSE frames only.\r\n");
 		} else {
 			/*
 			 * Per the IEEE spec, at this point flow control
 			 * should be disabled.
 			 */
-			hw->fc.type = e1000_fc_none;
+			hw->fc.current_mode = e1000_fc_none;
 			hw_dbg(hw, "Flow Control = NONE.\r\n");
 		}
 
@@ -1185,7 +1185,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		}
 
 		if (duplex == HALF_DUPLEX)
-			hw->fc.type = e1000_fc_none;
+			hw->fc.current_mode = e1000_fc_none;
 
 		/*
 		 * Now we call a subroutine to actually force the MAC