ide: remove useless subdirs from drivers/ide/

Suggested-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

1 files changed, 0 insertions, 375 deletions

diff --git a/drivers/ide/pci/trm290.c b/drivers/ide/pci/trm290.c
deleted file mode 100644
index 75ea61526566..000000000000
--- a/drivers/ide/pci/trm290.c
+++ /dev/null
@@ -1,375 +0,0 @@
-/*
- *  Copyright (c) 1997-1998  Mark Lord
- *  Copyright (c) 2007       MontaVista Software, Inc. <source@mvista.com>
- *
- *  May be copied or modified under the terms of the GNU General Public License
- *
- *  June 22, 2004 - get rid of check_region
- *                   - Jesper Juhl
- *
- */
-
-/*
- * This module provides support for the bus-master IDE DMA function
- * of the Tekram TRM290 chip, used on a variety of PCI IDE add-on boards,
- * including a "Precision Instruments" board.  The TRM290 pre-dates
- * the sff-8038 standard (ide-dma.c) by a few months, and differs
- * significantly enough to warrant separate routines for some functions,
- * while re-using others from ide-dma.c.
- *
- * EXPERIMENTAL!  It works for me (a sample of one).
- *
- * Works reliably for me in DMA mode (READs only),
- * DMA WRITEs are disabled by default (see #define below);
- *
- * DMA is not enabled automatically for this chipset,
- * but can be turned on manually (with "hdparm -d1") at run time.
- *
- * I need volunteers with "spare" drives for further testing
- * and development, and maybe to help figure out the peculiarities.
- * Even knowing the registers (below), some things behave strangely.
- */
-
-#define TRM290_NO_DMA_WRITES	/* DMA writes seem unreliable sometimes */
-
-/*
- * TRM-290 PCI-IDE2 Bus Master Chip
- * ================================
- * The configuration registers are addressed in normal I/O port space
- * and are used as follows:
- *
- * trm290_base depends on jumper settings, and is probed for by ide-dma.c
- *
- * trm290_base+2 when WRITTEN: chiptest register (byte, write-only)
- *	bit7 must always be written as "1"
- *	bits6-2 undefined
- *	bit1 1=legacy_compatible_mode, 0=native_pci_mode
- *	bit0 1=test_mode, 0=normal(default)
- *
- * trm290_base+2 when READ: status register (byte, read-only)
- *	bits7-2 undefined
- *	bit1 channel0 busmaster interrupt status 0=none, 1=asserted
- *	bit0 channel0 interrupt status 0=none, 1=asserted
- *
- * trm290_base+3 Interrupt mask register
- *	bits7-5 undefined
- *	bit4 legacy_header: 1=present, 0=absent
- *	bit3 channel1 busmaster interrupt status 0=none, 1=asserted (read only)
- *	bit2 channel1 interrupt status 0=none, 1=asserted (read only)
- *	bit1 channel1 interrupt mask: 1=masked, 0=unmasked(default)
- *	bit0 channel0 interrupt mask: 1=masked, 0=unmasked(default)
- *
- * trm290_base+1 "CPR" Config Pointer Register (byte)
- *	bit7 1=autoincrement CPR bits 2-0 after each access of CDR
- *	bit6 1=min. 1 wait-state posted write cycle (default), 0=0 wait-state
- *	bit5 0=enabled master burst access (default), 1=disable  (write only)
- *	bit4 PCI DEVSEL# timing select: 1=medium(default), 0=fast
- *	bit3 0=primary IDE channel, 1=secondary IDE channel
- *	bits2-0 register index for accesses through CDR port
- *
- * trm290_base+0 "CDR" Config Data Register (word)
- *	two sets of seven config registers,
- *	selected by CPR bit 3 (channel) and CPR bits 2-0 (index 0 to 6),
- *	each index defined below:
- *
- * Index-0 Base address register for command block (word)
- *	defaults: 0x1f0 for primary, 0x170 for secondary
- *
- * Index-1 general config register (byte)
- *	bit7 1=DMA enable, 0=DMA disable
- *	bit6 1=activate IDE_RESET, 0=no action (default)
- *	bit5 1=enable IORDY, 0=disable IORDY (default)
- *	bit4 0=16-bit data port(default), 1=8-bit (XT) data port
- *	bit3 interrupt polarity: 1=active_low, 0=active_high(default)
- *	bit2 power-saving-mode(?): 1=enable, 0=disable(default) (write only)
- *	bit1 bus_master_mode(?): 1=enable, 0=disable(default)
- *	bit0 enable_io_ports: 1=enable(default), 0=disable
- *
- * Index-2 read-ahead counter preload bits 0-7 (byte, write only)
- *	bits7-0 bits7-0 of readahead count
- *
- * Index-3 read-ahead config register (byte, write only)
- *	bit7 1=enable_readahead, 0=disable_readahead(default)
- *	bit6 1=clear_FIFO, 0=no_action
- *	bit5 undefined
- *	bit4 mode4 timing control: 1=enable, 0=disable(default)
- *	bit3 undefined
- *	bit2 undefined
- *	bits1-0 bits9-8 of read-ahead count
- *
- * Index-4 base address register for control block (word)
- *	defaults: 0x3f6 for primary, 0x376 for secondary
- *
- * Index-5 data port timings (shared by both drives) (byte)
- *	standard PCI "clk" (clock) counts, default value = 0xf5
- *
- *	bits7-6 setup time:  00=1clk, 01=2clk, 10=3clk, 11=4clk
- *	bits5-3 hold time:	000=1clk, 001=2clk, 010=3clk,
- *				011=4clk, 100=5clk, 101=6clk,
- *				110=8clk, 111=12clk
- *	bits2-0 active time:	000=2clk, 001=3clk, 010=4clk,
- *				011=5clk, 100=6clk, 101=8clk,
- *				110=12clk, 111=16clk
- *
- * Index-6 command/control port timings (shared by both drives) (byte)
- *	same layout as Index-5, default value = 0xde
- *
- * Suggested CDR programming for PIO mode0 (600ns):
- *	0x01f0,0x21,0xff,0x80,0x03f6,0xf5,0xde	; primary
- *	0x0170,0x21,0xff,0x80,0x0376,0xf5,0xde	; secondary
- *
- * Suggested CDR programming for PIO mode3 (180ns):
- *	0x01f0,0x21,0xff,0x80,0x03f6,0x09,0xde	; primary
- *	0x0170,0x21,0xff,0x80,0x0376,0x09,0xde	; secondary
- *
- * Suggested CDR programming for PIO mode4 (120ns):
- *	0x01f0,0x21,0xff,0x80,0x03f6,0x00,0xde	; primary
- *	0x0170,0x21,0xff,0x80,0x0376,0x00,0xde	; secondary
- *
- */
-
-#include <linux/types.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/ioport.h>
-#include <linux/interrupt.h>
-#include <linux/blkdev.h>
-#include <linux/init.h>
-#include <linux/pci.h>
-#include <linux/ide.h>
-
-#include <asm/io.h>
-
-#define DRV_NAME "trm290"
-
-static void trm290_prepare_drive (ide_drive_t *drive, unsigned int use_dma)
-{
-	ide_hwif_t *hwif = HWIF(drive);
-	u16 reg = 0;
-	unsigned long flags;
-
-	/* select PIO or DMA */
-	reg = use_dma ? (0x21 | 0x82) : (0x21 & ~0x82);
-
-	local_irq_save(flags);
-
-	if (reg != hwif->select_data) {
-		hwif->select_data = reg;
-		/* set PIO/DMA */
-		outb(0x51 | (hwif->channel << 3), hwif->config_data + 1);
-		outw(reg & 0xff, hwif->config_data);
-	}
-
-	/* enable IRQ if not probing */
-	if (drive->dev_flags & IDE_DFLAG_PRESENT) {
-		reg = inw(hwif->config_data + 3);
-		reg &= 0x13;
-		reg &= ~(1 << hwif->channel);
-		outw(reg, hwif->config_data + 3);
-	}
-
-	local_irq_restore(flags);
-}
-
-static void trm290_selectproc (ide_drive_t *drive)
-{
-	trm290_prepare_drive(drive, !!(drive->dev_flags & IDE_DFLAG_USING_DMA));
-}
-
-static void trm290_dma_exec_cmd(ide_drive_t *drive, u8 command)
-{
-	ide_execute_command(drive, command, &ide_dma_intr, WAIT_CMD, NULL);
-}
-
-static int trm290_dma_setup(ide_drive_t *drive)
-{
-	ide_hwif_t *hwif = drive->hwif;
-	struct request *rq = hwif->hwgroup->rq;
-	unsigned int count, rw;
-
-	if (rq_data_dir(rq)) {
-#ifdef TRM290_NO_DMA_WRITES
-		/* always use PIO for writes */
-		trm290_prepare_drive(drive, 0);	/* select PIO xfer */
-		return 1;
-#endif
-		rw = 1;
-	} else
-		rw = 2;
-
-	if (!(count = ide_build_dmatable(drive, rq))) {
-		/* try PIO instead of DMA */
-		trm290_prepare_drive(drive, 0); /* select PIO xfer */
-		return 1;
-	}
-	/* select DMA xfer */
-	trm290_prepare_drive(drive, 1);
-	outl(hwif->dmatable_dma | rw, hwif->dma_base);
-	drive->waiting_for_dma = 1;
-	/* start DMA */
-	outw(count * 2 - 1, hwif->dma_base + 2);
-	return 0;
-}
-
-static void trm290_dma_start(ide_drive_t *drive)
-{
-}
-
-static int trm290_dma_end(ide_drive_t *drive)
-{
-	u16 status;
-
-	drive->waiting_for_dma = 0;
-	/* purge DMA mappings */
-	ide_destroy_dmatable(drive);
-	status = inw(HWIF(drive)->dma_base + 2);
-	return status != 0x00ff;
-}
-
-static int trm290_dma_test_irq(ide_drive_t *drive)
-{
-	u16 status;
-
-	status = inw(HWIF(drive)->dma_base + 2);
-	return status == 0x00ff;
-}
-
-static void trm290_dma_host_set(ide_drive_t *drive, int on)
-{
-}
-
-static void __devinit init_hwif_trm290(ide_hwif_t *hwif)
-{
-	struct pci_dev *dev	= to_pci_dev(hwif->dev);
-	unsigned int  cfg_base	= pci_resource_start(dev, 4);
-	unsigned long flags;
-	u8 reg = 0;
-
-	if ((dev->class & 5) && cfg_base)
-		printk(KERN_INFO DRV_NAME " %s: chip", pci_name(dev));
-	else {
-		cfg_base = 0x3df0;
-		printk(KERN_INFO DRV_NAME " %s: using default", pci_name(dev));
-	}
-	printk(KERN_CONT " config base at 0x%04x\n", cfg_base);
-	hwif->config_data = cfg_base;
-	hwif->dma_base = (cfg_base + 4) ^ (hwif->channel ? 0x80 : 0);
-
-	printk(KERN_INFO "    %s: BM-DMA at 0x%04lx-0x%04lx\n",
-	       hwif->name, hwif->dma_base, hwif->dma_base + 3);
-
-	if (ide_allocate_dma_engine(hwif))
-		return;
-
-	local_irq_save(flags);
-	/* put config reg into first byte of hwif->select_data */
-	outb(0x51 | (hwif->channel << 3), hwif->config_data + 1);
-	/* select PIO as default */
-	hwif->select_data = 0x21;
-	outb(hwif->select_data, hwif->config_data);
-	/* get IRQ info */
-	reg = inb(hwif->config_data + 3);
-	/* mask IRQs for both ports */
-	reg = (reg & 0x10) | 0x03;
-	outb(reg, hwif->config_data + 3);
-	local_irq_restore(flags);
-
-	if (reg & 0x10)
-		/* legacy mode */
-		hwif->irq = hwif->channel ? 15 : 14;
-	else if (!hwif->irq && hwif->mate && hwif->mate->irq)
-		/* sharing IRQ with mate */
-		hwif->irq = hwif->mate->irq;
-
-#if 1
-	{
-	/*
-	 * My trm290-based card doesn't seem to work with all possible values
-	 * for the control basereg, so this kludge ensures that we use only
-	 * values that are known to work.  Ugh.		-ml
-	 */
-		u16 new, old, compat = hwif->channel ? 0x374 : 0x3f4;
-		static u16 next_offset = 0;
-		u8 old_mask;
-
-		outb(0x54 | (hwif->channel << 3), hwif->config_data + 1);
-		old = inw(hwif->config_data);
-		old &= ~1;
-		old_mask = inb(old + 2);
-		if (old != compat && old_mask == 0xff) {
-			/* leave lower 10 bits untouched */
-			compat += (next_offset += 0x400);
-			hwif->io_ports.ctl_addr = compat + 2;
-			outw(compat | 1, hwif->config_data);
-			new = inw(hwif->config_data);
-			printk(KERN_INFO "%s: control basereg workaround: "
-				"old=0x%04x, new=0x%04x\n",
-				hwif->name, old, new & ~1);
-		}
-	}
-#endif
-}
-
-static const struct ide_port_ops trm290_port_ops = {
-	.selectproc		= trm290_selectproc,
-};
-
-static struct ide_dma_ops trm290_dma_ops = {
-	.dma_host_set		= trm290_dma_host_set,
-	.dma_setup 		= trm290_dma_setup,
-	.dma_exec_cmd		= trm290_dma_exec_cmd,
-	.dma_start 		= trm290_dma_start,
-	.dma_end		= trm290_dma_end,
-	.dma_test_irq		= trm290_dma_test_irq,
-	.dma_lost_irq		= ide_dma_lost_irq,
-	.dma_timeout		= ide_dma_timeout,
-};
-
-static const struct ide_port_info trm290_chipset __devinitdata = {
-	.name		= DRV_NAME,
-	.init_hwif	= init_hwif_trm290,
-	.chipset	= ide_trm290,
-	.port_ops	= &trm290_port_ops,
-	.dma_ops	= &trm290_dma_ops,
-	.host_flags	= IDE_HFLAG_NO_ATAPI_DMA |
-#if 0 /* play it safe for now */
-			  IDE_HFLAG_TRUST_BIOS_FOR_DMA |
-#endif
-			  IDE_HFLAG_NO_AUTODMA |
-			  IDE_HFLAG_NO_LBA48,
-};
-
-static int __devinit trm290_init_one(struct pci_dev *dev, const struct pci_device_id *id)
-{
-	return ide_pci_init_one(dev, &trm290_chipset, NULL);
-}
-
-static const struct pci_device_id trm290_pci_tbl[] = {
-	{ PCI_VDEVICE(TEKRAM, PCI_DEVICE_ID_TEKRAM_DC290), 0 },
-	{ 0, },
-};
-MODULE_DEVICE_TABLE(pci, trm290_pci_tbl);
-
-static struct pci_driver trm290_pci_driver = {
-	.name		= "TRM290_IDE",
-	.id_table	= trm290_pci_tbl,
-	.probe		= trm290_init_one,
-	.remove		= ide_pci_remove,
-};
-
-static int __init trm290_ide_init(void)
-{
-	return ide_pci_register_driver(&trm290_pci_driver);
-}
-
-static void __exit trm290_ide_exit(void)
-{
-	pci_unregister_driver(&trm290_pci_driver);
-}
-
-module_init(trm290_ide_init);
-module_exit(trm290_ide_exit);
-
-MODULE_AUTHOR("Mark Lord");
-MODULE_DESCRIPTION("PCI driver module for Tekram TRM290 IDE");
-MODULE_LICENSE("GPL");