Merge branch 'linux-2.6' into for-2.6.22

1 files changed, 12 insertions, 42 deletions

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 5d134bb75ba1..ca2e4f830c39 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -103,8 +103,10 @@ config BLK_DEV_IDE_SATA
 	---help---
 	  There are two drivers for Serial ATA controllers.
 
-	  The main driver, "libata", exists inside the SCSI subsystem
-	  and supports most modern SATA controllers.
+	  The main driver, "libata", uses the SCSI subsystem
+	  and supports most modern SATA controllers. In order to use it
+	  you may take a look at "Serial ATA (prod) and Parallel ATA
+	  (experimental) drivers".
 
 	  The IDE driver (which you are currently configuring) supports
 	  a few first-generation SATA controllers.
@@ -434,24 +436,8 @@ config BLK_DEV_IDEDMA_FORCED
 
 	  Generally say N here.
 
-config IDEDMA_PCI_AUTO
-	bool "Use PCI DMA by default when available"
-	---help---
-	  Prior to kernel version 2.1.112, Linux used to automatically use
-	  DMA for IDE drives and chipsets which support it. Due to concerns
-	  about a couple of cases where buggy hardware may have caused damage,
-	  the default is now to NOT use DMA automatically. To revert to the
-	  previous behaviour, say Y to this question.
-
-	  If you suspect your hardware is at all flakey, say N here.
-	  Do NOT email the IDE kernel people regarding this issue!
-
-	  It is normally safe to answer Y to this question unless your
-	  motherboard uses a VIA VP2 chipset, in which case you should say N.
-
 config IDEDMA_ONLYDISK
 	bool "Enable DMA only for disks "
-	depends on IDEDMA_PCI_AUTO
 	help
 	  This is used if you know your ATAPI Devices are going to fail DMA
 	  Transfers.
@@ -769,6 +755,14 @@ config BLK_DEV_TC86C001
 	help
 	This driver adds support for Toshiba TC86C001 GOKU-S chip.
 
+config BLK_DEV_CELLEB
+	tristate "Toshiba's Cell Reference Set IDE support"
+	depends on PPC_CELLEB
+	help
+	  This driver provides support for the built-in IDE controller on
+	  Toshiba Cell Reference Board.
+	  If unsure, say Y.
+
 endif
 
 config BLK_DEV_IDE_PMAC
@@ -800,14 +794,6 @@ config BLK_DEV_IDEDMA_PMAC
 	  to transfer data to and from memory.  Saying Y is safe and improves
 	  performance.
 
-config BLK_DEV_IDE_CELLEB
-	bool "Toshiba's Cell Reference Set IDE support"
-	depends on PPC_CELLEB
-	help
-	  This driver provides support for the built-in IDE controller on
-	  Toshiba Cell Reference Board.
-	  If unsure, say Y.
-
 config BLK_DEV_IDE_SWARM
 	tristate "IDE for Sibyte evaluation boards"
 	depends on SIBYTE_SB1xxx_SOC
@@ -851,19 +837,6 @@ config BLK_DEV_IDEDMA_ICS
 	  Say Y here if you want to add DMA (Direct Memory Access) support to
 	  the ICS IDE driver.
 
-config IDEDMA_ICS_AUTO
-	bool "Use ICS DMA by default"
-	depends on BLK_DEV_IDEDMA_ICS
-	help
-	  Prior to kernel version 2.1.112, Linux used to automatically use
-	  DMA for IDE drives and chipsets which support it. Due to concerns
-	  about a couple of cases where buggy hardware may have caused damage,
-	  the default is now to NOT use DMA automatically. To revert to the
-	  previous behaviour, say Y to this question.
-
-	  If you suspect your hardware is at all flakey, say N here.
-	  Do NOT email the IDE kernel people regarding this issue!
-
 config BLK_DEV_IDE_RAPIDE
 	tristate "RapIDE interface support"
 	depends on ARM && ARCH_ACORN
@@ -1086,9 +1059,6 @@ config IDEDMA_IVB
 
 	  It is normally safe to answer Y; however, the default is N.
 
-config IDEDMA_AUTO
-	def_bool IDEDMA_PCI_AUTO || IDEDMA_ICS_AUTO
-
 endif
 
 config BLK_DEV_HD_ONLY