Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (56 commits)
  i2c: Add detection capability to new-style drivers
  i2c: Call client_unregister for new-style devices too
  i2c: Clean up old chip drivers
  i2c-ibm_iic: Register child nodes
  i2c: New-style EEPROM driver using device IDs
  i2c: Export the i2c_bus_type symbol
  i2c-au1550: Fix PM support
  i2c-dev: Delete empty detach_client callback
  i2c: Drop stray references to lm_sensors
  i2c: Check for ACPI resource conflicts
  i2c-ocores: basic PM support
  i2c-sibyte: SWARM I2C board initialization
  i2c-i801: Fix handling of error conditions
  i2c-i801: Rename local variable temp to status
  i2c-i801: Properly report bus arbitration loss
  i2c-i801: Remove verbose debugging messages
  i2c-algo-pcf: Drop unused struct members
  i2c-algo-pcf: Multi-master lost-arbitration improvement
  i2c: Deprecate the legacy gpio drivers
  i2c-pxa: Initialize early
  ...

8 files changed, 701 insertions, 94 deletions

diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig
index 2da2edfa68ec..50e0a4653741 100644
--- a/drivers/i2c/chips/Kconfig
+++ b/drivers/i2c/chips/Kconfig
@@ -14,6 +14,32 @@ config DS1682
 	  This driver can also be built as a module.  If so, the module
 	  will be called ds1682.
 
+config AT24
+	tristate "EEPROMs from most vendors"
+	depends on SYSFS && EXPERIMENTAL
+	help
+	  Enable this driver to get read/write support to most I2C EEPROMs,
+	  after you configure the driver to know about each EEPROM on
+	  your target board.  Use these generic chip names, instead of
+	  vendor-specific ones like at24c64 or 24lc02:
+
+	     24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
+	     24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
+
+	  Unless you like data loss puzzles, always be sure that any chip
+	  you configure as a 24c32 (32 kbit) or larger is NOT really a
+	  24c16 (16 kbit) or smaller, and vice versa. Marking the chip
+	  as read-only won't help recover from this. Also, if your chip
+	  has any software write-protect mechanism you may want to review the
+	  code to make sure this driver won't turn it on by accident.
+
+	  If you use this with an SMBus adapter instead of an I2C adapter,
+	  full functionality is not available.  Only smaller devices are
+	  supported (24c16 and below, max 4 kByte).
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called at24.
+
 config SENSORS_EEPROM
 	tristate "EEPROM reader"
 	depends on EXPERIMENTAL
@@ -26,8 +52,8 @@ config SENSORS_EEPROM
 	  will be called eeprom.
 
 config SENSORS_PCF8574
-	tristate "Philips PCF8574 and PCF8574A"
-	depends on EXPERIMENTAL
+	tristate "Philips PCF8574 and PCF8574A (DEPRECATED)"
+	depends on EXPERIMENTAL && GPIO_PCF857X = "n"
 	default n
 	help
 	  If you say yes here you get support for Philips PCF8574 and 
@@ -36,12 +62,16 @@ config SENSORS_PCF8574
 	  This driver can also be built as a module.  If so, the module
 	  will be called pcf8574.
 
+	  This driver is deprecated and will be dropped soon. Use
+	  drivers/gpio/pcf857x.c instead.
+
 	  These devices are hard to detect and rarely found on mainstream
 	  hardware.  If unsure, say N.
 
 config PCF8575
-	tristate "Philips PCF8575"
+	tristate "Philips PCF8575 (DEPRECATED)"
 	default n
+	depends on GPIO_PCF857X = "n"
 	help
 	  If you say yes here you get support for Philips PCF8575 chip.
 	  This chip is a 16-bit I/O expander for the I2C bus.  Several other
@@ -50,12 +80,15 @@ config PCF8575
 	  This driver can also be built as a module.  If so, the module
 	  will be called pcf8575.
 
+	  This driver is deprecated and will be dropped soon. Use
+	  drivers/gpio/pcf857x.c instead.
+
 	  This device is hard to detect and is rarely found on mainstream
 	  hardware.  If unsure, say N.
 
 config SENSORS_PCA9539
 	tristate "Philips PCA9539 16-bit I/O port (DEPRECATED)"
-	depends on EXPERIMENTAL && GPIO_PCA9539 = "n"
+	depends on EXPERIMENTAL && GPIO_PCA953X = "n"
 	help
 	  If you say yes here you get support for the Philips PCA9539
 	  16-bit I/O port.
@@ -64,7 +97,7 @@ config SENSORS_PCA9539
 	  will be called pca9539.
 
 	  This driver is deprecated and will be dropped soon. Use
-	  drivers/gpio/pca9539.c instead.
+	  drivers/gpio/pca953x.c instead.
 
 config SENSORS_PCF8591
 	tristate "Philips PCF8591"
diff --git a/drivers/i2c/chips/Makefile b/drivers/i2c/chips/Makefile
index e47aca0ca5ae..39e3e69ed125 100644
--- a/drivers/i2c/chips/Makefile
+++ b/drivers/i2c/chips/Makefile
@@ -10,6 +10,7 @@
 #
 
 obj-$(CONFIG_DS1682)		+= ds1682.o
+obj-$(CONFIG_AT24)		+= at24.o
 obj-$(CONFIG_SENSORS_EEPROM)	+= eeprom.o
 obj-$(CONFIG_SENSORS_MAX6875)	+= max6875.o
 obj-$(CONFIG_SENSORS_PCA9539)	+= pca9539.o
diff --git a/drivers/i2c/chips/at24.c b/drivers/i2c/chips/at24.c
new file mode 100644
index 000000000000..e764c94f3e3d
--- /dev/null
+++ b/drivers/i2c/chips/at24.c
@@ -0,0 +1,583 @@
+/*
+ * at24.c - handle most I2C EEPROMs
+ *
+ * Copyright (C) 2005-2007 David Brownell
+ * Copyright (C) 2008 Wolfram Sang, Pengutronix
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/mutex.h>
+#include <linux/sysfs.h>
+#include <linux/mod_devicetable.h>
+#include <linux/log2.h>
+#include <linux/bitops.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/i2c/at24.h>
+
+/*
+ * I2C EEPROMs from most vendors are inexpensive and mostly interchangeable.
+ * Differences between different vendor product lines (like Atmel AT24C or
+ * MicroChip 24LC, etc) won't much matter for typical read/write access.
+ * There are also I2C RAM chips, likewise interchangeable. One example
+ * would be the PCF8570, which acts like a 24c02 EEPROM (256 bytes).
+ *
+ * However, misconfiguration can lose data. "Set 16-bit memory address"
+ * to a part with 8-bit addressing will overwrite data. Writing with too
+ * big a page size also loses data. And it's not safe to assume that the
+ * conventional addresses 0x50..0x57 only hold eeproms; a PCF8563 RTC
+ * uses 0x51, for just one example.
+ *
+ * Accordingly, explicit board-specific configuration data should be used
+ * in almost all cases. (One partial exception is an SMBus used to access
+ * "SPD" data for DRAM sticks. Those only use 24c02 EEPROMs.)
+ *
+ * So this driver uses "new style" I2C driver binding, expecting to be
+ * told what devices exist. That may be in arch/X/mach-Y/board-Z.c or
+ * similar kernel-resident tables; or, configuration data coming from
+ * a bootloader.
+ *
+ * Other than binding model, current differences from "eeprom" driver are
+ * that this one handles write access and isn't restricted to 24c02 devices.
+ * It also handles larger devices (32 kbit and up) with two-byte addresses,
+ * which won't work on pure SMBus systems.
+ */
+
+struct at24_data {
+	struct at24_platform_data chip;
+	bool use_smbus;
+
+	/*
+	 * Lock protects against activities from other Linux tasks,
+	 * but not from changes by other I2C masters.
+	 */
+	struct mutex lock;
+	struct bin_attribute bin;
+
+	u8 *writebuf;
+	unsigned write_max;
+	unsigned num_addresses;
+
+	/*
+	 * Some chips tie up multiple I2C addresses; dummy devices reserve
+	 * them for us, and we'll use them with SMBus calls.
+	 */
+	struct i2c_client *client[];
+};
+
+/*
+ * This parameter is to help this driver avoid blocking other drivers out
+ * of I2C for potentially troublesome amounts of time. With a 100 kHz I2C
+ * clock, one 256 byte read takes about 1/43 second which is excessive;
+ * but the 1/170 second it takes at 400 kHz may be quite reasonable; and
+ * at 1 MHz (Fm+) a 1/430 second delay could easily be invisible.
+ *
+ * This value is forced to be a power of two so that writes align on pages.
+ */
+static unsigned io_limit = 128;
+module_param(io_limit, uint, 0);
+MODULE_PARM_DESC(io_limit, "Maximum bytes per I/O (default 128)");
+
+/*
+ * Specs often allow 5 msec for a page write, sometimes 20 msec;
+ * it's important to recover from write timeouts.
+ */
+static unsigned write_timeout = 25;
+module_param(write_timeout, uint, 0);
+MODULE_PARM_DESC(write_timeout, "Time (in ms) to try writes (default 25)");
+
+#define AT24_SIZE_BYTELEN 5
+#define AT24_SIZE_FLAGS 8
+
+#define AT24_BITMASK(x) (BIT(x) - 1)
+
+/* create non-zero magic value for given eeprom parameters */
+#define AT24_DEVICE_MAGIC(_len, _flags) 		\
+	((1 << AT24_SIZE_FLAGS | (_flags)) 		\
+	    << AT24_SIZE_BYTELEN | ilog2(_len))
+
+static const struct i2c_device_id at24_ids[] = {
+	/* needs 8 addresses as A0-A2 are ignored */
+	{ "24c00", AT24_DEVICE_MAGIC(128 / 8, AT24_FLAG_TAKE8ADDR) },
+	/* old variants can't be handled with this generic entry! */
+	{ "24c01", AT24_DEVICE_MAGIC(1024 / 8, 0) },
+	{ "24c02", AT24_DEVICE_MAGIC(2048 / 8, 0) },
+	/* spd is a 24c02 in memory DIMMs */
+	{ "spd", AT24_DEVICE_MAGIC(2048 / 8,
+		AT24_FLAG_READONLY | AT24_FLAG_IRUGO) },
+	{ "24c04", AT24_DEVICE_MAGIC(4096 / 8, 0) },
+	/* 24rf08 quirk is handled at i2c-core */
+	{ "24c08", AT24_DEVICE_MAGIC(8192 / 8, 0) },
+	{ "24c16", AT24_DEVICE_MAGIC(16384 / 8, 0) },
+	{ "24c32", AT24_DEVICE_MAGIC(32768 / 8, AT24_FLAG_ADDR16) },
+	{ "24c64", AT24_DEVICE_MAGIC(65536 / 8, AT24_FLAG_ADDR16) },
+	{ "24c128", AT24_DEVICE_MAGIC(131072 / 8, AT24_FLAG_ADDR16) },
+	{ "24c256", AT24_DEVICE_MAGIC(262144 / 8, AT24_FLAG_ADDR16) },
+	{ "24c512", AT24_DEVICE_MAGIC(524288 / 8, AT24_FLAG_ADDR16) },
+	{ "24c1024", AT24_DEVICE_MAGIC(1048576 / 8, AT24_FLAG_ADDR16) },
+	{ "at24", 0 },
+	{ /* END OF LIST */ }
+};
+MODULE_DEVICE_TABLE(i2c, at24_ids);
+
+/*-------------------------------------------------------------------------*/
+
+/*
+ * This routine supports chips which consume multiple I2C addresses. It
+ * computes the addressing information to be used for a given r/w request.
+ * Assumes that sanity checks for offset happened at sysfs-layer.
+ */
+static struct i2c_client *at24_translate_offset(struct at24_data *at24,
+		unsigned *offset)
+{
+	unsigned i;
+
+	if (at24->chip.flags & AT24_FLAG_ADDR16) {
+		i = *offset >> 16;
+		*offset &= 0xffff;
+	} else {
+		i = *offset >> 8;
+		*offset &= 0xff;
+	}
+
+	return at24->client[i];
+}
+
+static ssize_t at24_eeprom_read(struct at24_data *at24, char *buf,
+		unsigned offset, size_t count)
+{
+	struct i2c_msg msg[2];
+	u8 msgbuf[2];
+	struct i2c_client *client;
+	int status, i;
+
+	memset(msg, 0, sizeof(msg));
+
+	/*
+	 * REVISIT some multi-address chips don't rollover page reads to
+	 * the next slave address, so we may need to truncate the count.
+	 * Those chips might need another quirk flag.
+	 *
+	 * If the real hardware used four adjacent 24c02 chips and that
+	 * were misconfigured as one 24c08, that would be a similar effect:
+	 * one "eeprom" file not four, but larger reads would fail when
+	 * they crossed certain pages.
+	 */
+
+	/*
+	 * Slave address and byte offset derive from the offset. Always
+	 * set the byte address; on a multi-master board, another master
+	 * may have changed the chip's "current" address pointer.
+	 */
+	client = at24_translate_offset(at24, &offset);
+
+	if (count > io_limit)
+		count = io_limit;
+
+	/* Smaller eeproms can work given some SMBus extension calls */
+	if (at24->use_smbus) {
+		if (count > I2C_SMBUS_BLOCK_MAX)
+			count = I2C_SMBUS_BLOCK_MAX;
+		status = i2c_smbus_read_i2c_block_data(client, offset,
+				count, buf);
+		dev_dbg(&client->dev, "smbus read %zd@%d --> %d\n",
+				count, offset, status);
+		return (status < 0) ? -EIO : status;
+	}
+
+	/*
+	 * When we have a better choice than SMBus calls, use a combined
+	 * I2C message. Write address; then read up to io_limit data bytes.
+	 * Note that read page rollover helps us here (unlike writes).
+	 * msgbuf is u8 and will cast to our needs.
+	 */
+	i = 0;
+	if (at24->chip.flags & AT24_FLAG_ADDR16)
+		msgbuf[i++] = offset >> 8;
+	msgbuf[i++] = offset;
+
+	msg[0].addr = client->addr;
+	msg[0].buf = msgbuf;
+	msg[0].len = i;
+
+	msg[1].addr = client->addr;
+	msg[1].flags = I2C_M_RD;
+	msg[1].buf = buf;
+	msg[1].len = count;
+
+	status = i2c_transfer(client->adapter, msg, 2);
+	dev_dbg(&client->dev, "i2c read %zd@%d --> %d\n",
+			count, offset, status);
+
+	if (status == 2)
+		return count;
+	else if (status >= 0)
+		return -EIO;
+	else
+		return status;
+}
+
+static ssize_t at24_bin_read(struct kobject *kobj, struct bin_attribute *attr,
+		char *buf, loff_t off, size_t count)
+{
+	struct at24_data *at24;
+	ssize_t retval = 0;
+
+	at24 = dev_get_drvdata(container_of(kobj, struct device, kobj));
+
+	if (unlikely(!count))
+		return count;
+
+	/*
+	 * Read data from chip, protecting against concurrent updates
+	 * from this host, but not from other I2C masters.
+	 */
+	mutex_lock(&at24->lock);
+
+	while (count) {
+		ssize_t	status;
+
+		status = at24_eeprom_read(at24, buf, off, count);
+		if (status <= 0) {
+			if (retval == 0)
+				retval = status;
+			break;
+		}
+		buf += status;
+		off += status;
+		count -= status;
+		retval += status;
+	}
+
+	mutex_unlock(&at24->lock);
+
+	return retval;
+}
+
+
+/*
+ * REVISIT: export at24_bin{read,write}() to let other kernel code use
+ * eeprom data. For example, it might hold a board's Ethernet address, or
+ * board-specific calibration data generated on the manufacturing floor.
+ */
+
+
+/*
+ * Note that if the hardware write-protect pin is pulled high, the whole
+ * chip is normally write protected. But there are plenty of product
+ * variants here, including OTP fuses and partial chip protect.
+ *
+ * We only use page mode writes; the alternative is sloooow. This routine
+ * writes at most one page.
+ */
+static ssize_t at24_eeprom_write(struct at24_data *at24, char *buf,
+		unsigned offset, size_t count)
+{
+	struct i2c_client *client;
+	struct i2c_msg msg;
+	ssize_t status;
+	unsigned long timeout, write_time;
+	unsigned next_page;
+
+	/* Get corresponding I2C address and adjust offset */
+	client = at24_translate_offset(at24, &offset);
+
+	/* write_max is at most a page */
+	if (count > at24->write_max)
+		count = at24->write_max;
+
+	/* Never roll over backwards, to the start of this page */
+	next_page = roundup(offset + 1, at24->chip.page_size);
+	if (offset + count > next_page)
+		count = next_page - offset;
+
+	/* If we'll use I2C calls for I/O, set up the message */
+	if (!at24->use_smbus) {
+		int i = 0;
+
+		msg.addr = client->addr;
+		msg.flags = 0;
+
+		/* msg.buf is u8 and casts will mask the values */
+		msg.buf = at24->writebuf;
+		if (at24->chip.flags & AT24_FLAG_ADDR16)
+			msg.buf[i++] = offset >> 8;
+
+		msg.buf[i++] = offset;
+		memcpy(&msg.buf[i], buf, count);
+		msg.len = i + count;
+	}
+
+	/*
+	 * Writes fail if the previous one didn't complete yet. We may
+	 * loop a few times until this one succeeds, waiting at least
+	 * long enough for one entire page write to work.
+	 */
+	timeout = jiffies + msecs_to_jiffies(write_timeout);
+	do {
+		write_time = jiffies;
+		if (at24->use_smbus) {
+			status = i2c_smbus_write_i2c_block_data(client,
+					offset, count, buf);
+			if (status == 0)
+				status = count;
+		} else {
+			status = i2c_transfer(client->adapter, &msg, 1);
+			if (status == 1)
+				status = count;
+		}
+		dev_dbg(&client->dev, "write %zd@%d --> %zd (%ld)\n",
+				count, offset, status, jiffies);
+
+		if (status == count)
+			return count;
+
+		/* REVISIT: at HZ=100, this is sloooow */
+		msleep(1);
+	} while (time_before(write_time, timeout));
+
+	return -ETIMEDOUT;
+}
+
+static ssize_t at24_bin_write(struct kobject *kobj, struct bin_attribute *attr,
+		char *buf, loff_t off, size_t count)
+{
+	struct at24_data *at24;
+	ssize_t retval = 0;
+
+	at24 = dev_get_drvdata(container_of(kobj, struct device, kobj));
+
+	if (unlikely(!count))
+		return count;
+
+	/*
+	 * Write data to chip, protecting against concurrent updates
+	 * from this host, but not from other I2C masters.
+	 */
+	mutex_lock(&at24->lock);
+
+	while (count) {
+		ssize_t	status;
+
+		status = at24_eeprom_write(at24, buf, off, count);
+		if (status <= 0) {
+			if (retval == 0)
+				retval = status;
+			break;
+		}
+		buf += status;
+		off += status;
+		count -= status;
+		retval += status;
+	}
+
+	mutex_unlock(&at24->lock);
+
+	return retval;
+}
+
+/*-------------------------------------------------------------------------*/
+
+static int at24_probe(struct i2c_client *client, const struct i2c_device_id *id)
+{
+	struct at24_platform_data chip;
+	bool writable;
+	bool use_smbus = false;
+	struct at24_data *at24;
+	int err;
+	unsigned i, num_addresses;
+	kernel_ulong_t magic;
+
+	if (client->dev.platform_data) {
+		chip = *(struct at24_platform_data *)client->dev.platform_data;
+	} else {
+		if (!id->driver_data) {
+			err = -ENODEV;
+			goto err_out;
+		}
+		magic = id->driver_data;
+		chip.byte_len = BIT(magic & AT24_BITMASK(AT24_SIZE_BYTELEN));
+		magic >>= AT24_SIZE_BYTELEN;
+		chip.flags = magic & AT24_BITMASK(AT24_SIZE_FLAGS);
+		/*
+		 * This is slow, but we can't know all eeproms, so we better
+		 * play safe. Specifying custom eeprom-types via platform_data
+		 * is recommended anyhow.
+		 */
+		chip.page_size = 1;
+	}
+
+	if (!is_power_of_2(chip.byte_len))
+		dev_warn(&client->dev,
+			"byte_len looks suspicious (no power of 2)!\n");
+	if (!is_power_of_2(chip.page_size))
+		dev_warn(&client->dev,
+			"page_size looks suspicious (no power of 2)!\n");
+
+	/* Use I2C operations unless we're stuck with SMBus extensions. */
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+		if (chip.flags & AT24_FLAG_ADDR16) {
+			err = -EPFNOSUPPORT;
+			goto err_out;
+		}
+		if (!i2c_check_functionality(client->adapter,
+				I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
+			err = -EPFNOSUPPORT;
+			goto err_out;
+		}
+		use_smbus = true;
+	}
+
+	if (chip.flags & AT24_FLAG_TAKE8ADDR)
+		num_addresses = 8;
+	else
+		num_addresses =	DIV_ROUND_UP(chip.byte_len,
+			(chip.flags & AT24_FLAG_ADDR16) ? 65536 : 256);
+
+	at24 = kzalloc(sizeof(struct at24_data) +
+		num_addresses * sizeof(struct i2c_client *), GFP_KERNEL);
+	if (!at24) {
+		err = -ENOMEM;
+		goto err_out;
+	}
+
+	mutex_init(&at24->lock);
+	at24->use_smbus = use_smbus;
+	at24->chip = chip;
+	at24->num_addresses = num_addresses;
+
+	/*
+	 * Export the EEPROM bytes through sysfs, since that's convenient.
+	 * By default, only root should see the data (maybe passwords etc)
+	 */
+	at24->bin.attr.name = "eeprom";
+	at24->bin.attr.mode = chip.flags & AT24_FLAG_IRUGO ? S_IRUGO : S_IRUSR;
+	at24->bin.attr.owner = THIS_MODULE;
+	at24->bin.read = at24_bin_read;
+	at24->bin.size = chip.byte_len;
+
+	writable = !(chip.flags & AT24_FLAG_READONLY);
+	if (writable) {
+		if (!use_smbus || i2c_check_functionality(client->adapter,
+				I2C_FUNC_SMBUS_WRITE_I2C_BLOCK)) {
+
+			unsigned write_max = chip.page_size;
+
+			at24->bin.write = at24_bin_write;
+			at24->bin.attr.mode |= S_IWUSR;
+
+			if (write_max > io_limit)
+				write_max = io_limit;
+			if (use_smbus && write_max > I2C_SMBUS_BLOCK_MAX)
+				write_max = I2C_SMBUS_BLOCK_MAX;
+			at24->write_max = write_max;
+
+			/* buffer (data + address at the beginning) */
+			at24->writebuf = kmalloc(write_max + 2, GFP_KERNEL);
+			if (!at24->writebuf) {
+				err = -ENOMEM;
+				goto err_struct;
+			}
+		} else {
+			dev_warn(&client->dev,
+				"cannot write due to controller restrictions.");
+		}
+	}
+
+	at24->client[0] = client;
+
+	/* use dummy devices for multiple-address chips */
+	for (i = 1; i < num_addresses; i++) {
+		at24->client[i] = i2c_new_dummy(client->adapter,
+					client->addr + i);
+		if (!at24->client[i]) {
+			dev_err(&client->dev, "address 0x%02x unavailable\n",
+					client->addr + i);
+			err = -EADDRINUSE;
+			goto err_clients;
+		}
+	}
+
+	err = sysfs_create_bin_file(&client->dev.kobj, &at24->bin);
+	if (err)
+		goto err_clients;
+
+	i2c_set_clientdata(client, at24);
+
+	dev_info(&client->dev, "%Zd byte %s EEPROM %s\n",
+		at24->bin.size, client->name,
+		writable ? "(writable)" : "(read-only)");
+	dev_dbg(&client->dev,
+		"page_size %d, num_addresses %d, write_max %d%s\n",
+		chip.page_size, num_addresses,
+		at24->write_max,
+		use_smbus ? ", use_smbus" : "");
+
+	return 0;
+
+err_clients:
+	for (i = 1; i < num_addresses; i++)
+		if (at24->client[i])
+			i2c_unregister_device(at24->client[i]);
+
+	kfree(at24->writebuf);
+err_struct:
+	kfree(at24);
+err_out:
+	dev_dbg(&client->dev, "probe error %d\n", err);
+	return err;
+}
+
+static int __devexit at24_remove(struct i2c_client *client)
+{
+	struct at24_data *at24;
+	int i;
+
+	at24 = i2c_get_clientdata(client);
+	sysfs_remove_bin_file(&client->dev.kobj, &at24->bin);
+
+	for (i = 1; i < at24->num_addresses; i++)
+		i2c_unregister_device(at24->client[i]);
+
+	kfree(at24->writebuf);
+	kfree(at24);
+	i2c_set_clientdata(client, NULL);
+	return 0;
+}
+
+/*-------------------------------------------------------------------------*/
+
+static struct i2c_driver at24_driver = {
+	.driver = {
+		.name = "at24",
+		.owner = THIS_MODULE,
+	},
+	.probe = at24_probe,
+	.remove = __devexit_p(at24_remove),
+	.id_table = at24_ids,
+};
+
+static int __init at24_init(void)
+{
+	io_limit = rounddown_pow_of_two(io_limit);
+	return i2c_add_driver(&at24_driver);
+}
+module_init(at24_init);
+
+static void __exit at24_exit(void)
+{
+	i2c_del_driver(&at24_driver);
+}
+module_exit(at24_exit);
+
+MODULE_DESCRIPTION("Driver for most I2C EEPROMs");
+MODULE_AUTHOR("David Brownell and Wolfram Sang");
+MODULE_LICENSE("GPL");
diff --git a/drivers/i2c/chips/eeprom.c b/drivers/i2c/chips/eeprom.c
index 7dee001e5133..373ea8d8fe8f 100644
--- a/drivers/i2c/chips/eeprom.c
+++ b/drivers/i2c/chips/eeprom.c
@@ -1,15 +1,9 @@
 /*
-    eeprom.c - Part of lm_sensors, Linux kernel modules for hardware
-               monitoring
     Copyright (C) 1998, 1999  Frodo Looijaard <frodol@dds.nl> and
 			       Philip Edelbrock <phil@netroedge.com>
     Copyright (C) 2003 Greg Kroah-Hartman <greg@kroah.com>
     Copyright (C) 2003 IBM Corp.
-
-    2004-01-16  Jean Delvare <khali@linux-fr.org>
-    Divide the eeprom in 32-byte (arbitrary) slices. This significantly
-    speeds sensors up, as well as various scripts using the eeprom
-    module.
+    Copyright (C) 2004 Jean Delvare <khali@linux-fr.org>
 
     This program is free software; you can redistribute it and/or modify
     it under the terms of the GNU General Public License as published by
@@ -78,7 +72,7 @@ static struct i2c_driver eeprom_driver = {
 static void eeprom_update_client(struct i2c_client *client, u8 slice)
 {
 	struct eeprom_data *data = i2c_get_clientdata(client);
-	int i, j;
+	int i;
 
 	mutex_lock(&data->update_lock);
 
@@ -93,15 +87,12 @@ static void eeprom_update_client(struct i2c_client *client, u8 slice)
 							!= 32)
 					goto exit;
 		} else {
-			if (i2c_smbus_write_byte(client, slice << 5)) {
-				dev_dbg(&client->dev, "eeprom read start has failed!\n");
-				goto exit;
-			}
-			for (i = slice << 5; i < (slice + 1) << 5; i++) {
-				j = i2c_smbus_read_byte(client);
-				if (j < 0)
+			for (i = slice << 5; i < (slice + 1) << 5; i += 2) {
+				int word = i2c_smbus_read_word_data(client, i);
+				if (word < 0)
 					goto exit;
-				data->data[i] = (u8) j;
+				data->data[i] = word & 0xff;
+				data->data[i + 1] = word >> 8;
 			}
 		}
 		data->last_updated[slice] = jiffies;
@@ -159,24 +150,33 @@ static struct bin_attribute eeprom_attr = {
 
 static int eeprom_attach_adapter(struct i2c_adapter *adapter)
 {
+	if (!(adapter->class & (I2C_CLASS_DDC | I2C_CLASS_SPD)))
+		return 0;
 	return i2c_probe(adapter, &addr_data, eeprom_detect);
 }
 
 /* This function is called by i2c_probe */
 static int eeprom_detect(struct i2c_adapter *adapter, int address, int kind)
 {
-	struct i2c_client *new_client;
+	struct i2c_client *client;
 	struct eeprom_data *data;
 	int err = 0;
 
-	/* There are three ways we can read the EEPROM data:
+	/* EDID EEPROMs are often 24C00 EEPROMs, which answer to all
+	   addresses 0x50-0x57, but we only care about 0x50. So decline
+	   attaching to addresses >= 0x51 on DDC buses */
+	if (!(adapter->class & I2C_CLASS_SPD) && address >= 0x51)
+		goto exit;
+
+	/* There are four ways we can read the EEPROM data:
 	   (1) I2C block reads (faster, but unsupported by most adapters)
-	   (2) Consecutive byte reads (100% overhead)
-	   (3) Regular byte data reads (200% overhead)
-	   The third method is not implemented by this driver because all
-	   known adapters support at least the second. */
-	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_BYTE_DATA
-					    | I2C_FUNC_SMBUS_BYTE))
+	   (2) Word reads (128% overhead)
+	   (3) Consecutive byte reads (88% overhead, unsafe)
+	   (4) Regular byte data reads (265% overhead)
+	   The third and fourth methods are not implemented by this driver
+	   because all known adapters support one of the first two. */
+	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_WORD_DATA)
+	 && !i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_I2C_BLOCK))
 		goto exit;
 
 	if (!(data = kzalloc(sizeof(struct eeprom_data), GFP_KERNEL))) {
@@ -184,50 +184,49 @@ static int eeprom_detect(struct i2c_adapter *adapter, int address, int kind)
 		goto exit;
 	}
 
-	new_client = &data->client;
+	client = &data->client;
 	memset(data->data, 0xff, EEPROM_SIZE);
-	i2c_set_clientdata(new_client, data);
-	new_client->addr = address;
-	new_client->adapter = adapter;
-	new_client->driver = &eeprom_driver;
-	new_client->flags = 0;
+	i2c_set_clientdata(client, data);
+	client->addr = address;
+	client->adapter = adapter;
+	client->driver = &eeprom_driver;
 
 	/* Fill in the remaining client fields */
-	strlcpy(new_client->name, "eeprom", I2C_NAME_SIZE);
-	data->valid = 0;
+	strlcpy(client->name, "eeprom", I2C_NAME_SIZE);
 	mutex_init(&data->update_lock);
 	data->nature = UNKNOWN;
 
 	/* Tell the I2C layer a new client has arrived */
-	if ((err = i2c_attach_client(new_client)))
+	if ((err = i2c_attach_client(client)))
 		goto exit_kfree;
 
 	/* Detect the Vaio nature of EEPROMs.
 	   We use the "PCG-" or "VGN-" prefix as the signature. */
-	if (address == 0x57) {
+	if (address == 0x57
+	 && i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_BYTE_DATA)) {
 		char name[4];
 
-		name[0] = i2c_smbus_read_byte_data(new_client, 0x80);
-		name[1] = i2c_smbus_read_byte(new_client);
-		name[2] = i2c_smbus_read_byte(new_client);
-		name[3] = i2c_smbus_read_byte(new_client);
+		name[0] = i2c_smbus_read_byte_data(client, 0x80);
+		name[1] = i2c_smbus_read_byte_data(client, 0x81);
+		name[2] = i2c_smbus_read_byte_data(client, 0x82);
+		name[3] = i2c_smbus_read_byte_data(client, 0x83);
 
 		if (!memcmp(name, "PCG-", 4) || !memcmp(name, "VGN-", 4)) {
-			dev_info(&new_client->dev, "Vaio EEPROM detected, "
+			dev_info(&client->dev, "Vaio EEPROM detected, "
 				 "enabling privacy protection\n");
 			data->nature = VAIO;
 		}
 	}
 
 	/* create the sysfs eeprom file */
-	err = sysfs_create_bin_file(&new_client->dev.kobj, &eeprom_attr);
+	err = sysfs_create_bin_file(&client->dev.kobj, &eeprom_attr);
 	if (err)
 		goto exit_detach;
 
 	return 0;
 
 exit_detach:
-	i2c_detach_client(new_client);
+	i2c_detach_client(client);
 exit_kfree:
 	kfree(data);
 exit:
diff --git a/drivers/i2c/chips/max6875.c b/drivers/i2c/chips/max6875.c
index cf507b3f60f3..5a0285d8b6f9 100644
--- a/drivers/i2c/chips/max6875.c
+++ b/drivers/i2c/chips/max6875.c
@@ -170,7 +170,7 @@ static int max6875_detect(struct i2c_adapter *adapter, int address, int kind)
 	struct i2c_client *real_client;
 	struct i2c_client *fake_client;
 	struct max6875_data *data;
-	int err = 0;
+	int err;
 
 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WRITE_BYTE_DATA
 				     | I2C_FUNC_SMBUS_READ_BYTE))
@@ -195,7 +195,6 @@ static int max6875_detect(struct i2c_adapter *adapter, int address, int kind)
 	real_client->addr = address;
 	real_client->adapter = adapter;
 	real_client->driver = &max6875_driver;
-	real_client->flags = 0;
 	strlcpy(real_client->name, "max6875", I2C_NAME_SIZE);
 	mutex_init(&data->update_lock);
 
@@ -204,7 +203,6 @@ static int max6875_detect(struct i2c_adapter *adapter, int address, int kind)
 	fake_client->addr = address | 1;
 	fake_client->adapter = adapter;
 	fake_client->driver = &max6875_driver;
-	fake_client->flags = 0;
 	strlcpy(fake_client->name, "max6875 subclient", I2C_NAME_SIZE);
 
 	if ((err = i2c_attach_client(real_client)) != 0)
diff --git a/drivers/i2c/chips/pca9539.c b/drivers/i2c/chips/pca9539.c
index f43c4e79b55e..58ab7f26be26 100644
--- a/drivers/i2c/chips/pca9539.c
+++ b/drivers/i2c/chips/pca9539.c
@@ -113,7 +113,7 @@ static int pca9539_attach_adapter(struct i2c_adapter *adapter)
 /* This function is called by i2c_probe */
 static int pca9539_detect(struct i2c_adapter *adapter, int address, int kind)
 {
-	struct i2c_client *new_client;
+	struct i2c_client *client;
 	struct pca9539_data *data;
 	int err = 0;
 
@@ -127,29 +127,28 @@ static int pca9539_detect(struct i2c_adapter *adapter, int address, int kind)
 		goto exit;
 	}
 
-	new_client = &data->client;
-	i2c_set_clientdata(new_client, data);
-	new_client->addr = address;
-	new_client->adapter = adapter;
-	new_client->driver = &pca9539_driver;
-	new_client->flags = 0;
+	client = &data->client;
+	i2c_set_clientdata(client, data);
+	client->addr = address;
+	client->adapter = adapter;
+	client->driver = &pca9539_driver;
 
 	if (kind < 0) {
 		/* Detection: the pca9539 only has 8 registers (0-7).
 		   A read of 7 should succeed, but a read of 8 should fail. */
-		if ((i2c_smbus_read_byte_data(new_client, 7) < 0) ||
-		    (i2c_smbus_read_byte_data(new_client, 8) >= 0))
+		if ((i2c_smbus_read_byte_data(client, 7) < 0) ||
+		    (i2c_smbus_read_byte_data(client, 8) >= 0))
 			goto exit_kfree;
 	}
 
-	strlcpy(new_client->name, "pca9539", I2C_NAME_SIZE);
+	strlcpy(client->name, "pca9539", I2C_NAME_SIZE);
 
 	/* Tell the I2C layer a new client has arrived */
-	if ((err = i2c_attach_client(new_client)))
+	if ((err = i2c_attach_client(client)))
 		goto exit_kfree;
 
 	/* Register sysfs hooks */
-	err = sysfs_create_group(&new_client->dev.kobj,
+	err = sysfs_create_group(&client->dev.kobj,
 				 &pca9539_defattr_group);
 	if (err)
 		goto exit_detach;
@@ -157,7 +156,7 @@ static int pca9539_detect(struct i2c_adapter *adapter, int address, int kind)
 	return 0;
 
 exit_detach:
-	i2c_detach_client(new_client);
+	i2c_detach_client(client);
 exit_kfree:
 	kfree(data);
 exit:
diff --git a/drivers/i2c/chips/pcf8574.c b/drivers/i2c/chips/pcf8574.c
index e5b31329b56e..1b3db2b3ada9 100644
--- a/drivers/i2c/chips/pcf8574.c
+++ b/drivers/i2c/chips/pcf8574.c
@@ -1,6 +1,4 @@
 /*
-    pcf8574.c - Part of lm_sensors, Linux kernel modules for hardware
-             monitoring
     Copyright (c) 2000  Frodo Looijaard <frodol@dds.nl>, 
                         Philip Edelbrock <phil@netroedge.com>,
                         Dan Eaton <dan.eaton@rocketlogix.com>
@@ -129,7 +127,7 @@ static int pcf8574_attach_adapter(struct i2c_adapter *adapter)
 /* This function is called by i2c_probe */
 static int pcf8574_detect(struct i2c_adapter *adapter, int address, int kind)
 {
-	struct i2c_client *new_client;
+	struct i2c_client *client;
 	struct pcf8574_data *data;
 	int err = 0;
 	const char *client_name = "";
@@ -144,12 +142,11 @@ static int pcf8574_detect(struct i2c_adapter *adapter, int address, int kind)
 		goto exit;
 	}
 
-	new_client = &data->client;
-	i2c_set_clientdata(new_client, data);
-	new_client->addr = address;
-	new_client->adapter = adapter;
-	new_client->driver = &pcf8574_driver;
-	new_client->flags = 0;
+	client = &data->client;
+	i2c_set_clientdata(client, data);
+	client->addr = address;
+	client->adapter = adapter;
+	client->driver = &pcf8574_driver;
 
 	/* Now, we would do the remaining detection. But the PCF8574 is plainly
 	   impossible to detect! Stupid chip. */
@@ -168,23 +165,23 @@ static int pcf8574_detect(struct i2c_adapter *adapter, int address, int kind)
 		client_name = "pcf8574";
 
 	/* Fill in the remaining client fields and put it into the global list */
-	strlcpy(new_client->name, client_name, I2C_NAME_SIZE);
+	strlcpy(client->name, client_name, I2C_NAME_SIZE);
 
 	/* Tell the I2C layer a new client has arrived */
-	if ((err = i2c_attach_client(new_client)))
+	if ((err = i2c_attach_client(client)))
 		goto exit_free;
 	
 	/* Initialize the PCF8574 chip */
-	pcf8574_init_client(new_client);
+	pcf8574_init_client(client);
 
 	/* Register sysfs hooks */
-	err = sysfs_create_group(&new_client->dev.kobj, &pcf8574_attr_group);
+	err = sysfs_create_group(&client->dev.kobj, &pcf8574_attr_group);
 	if (err)
 		goto exit_detach;
 	return 0;
 
       exit_detach:
-	i2c_detach_client(new_client);
+	i2c_detach_client(client);
       exit_free:
 	kfree(data);
       exit:
diff --git a/drivers/i2c/chips/pcf8591.c b/drivers/i2c/chips/pcf8591.c
index 66c7c3bb9429..db735379f22f 100644
--- a/drivers/i2c/chips/pcf8591.c
+++ b/drivers/i2c/chips/pcf8591.c
@@ -1,6 +1,4 @@
 /*
-    pcf8591.c - Part of lm_sensors, Linux kernel modules for hardware
-                monitoring
     Copyright (C) 2001-2004 Aurelien Jarno <aurelien@aurel32.net>
     Ported to Linux 2.6 by Aurelien Jarno <aurelien@aurel32.net> with 
     the help of Jean Delvare <khali@linux-fr.org>
@@ -190,7 +188,7 @@ static int pcf8591_attach_adapter(struct i2c_adapter *adapter)
 /* This function is called by i2c_probe */
 static int pcf8591_detect(struct i2c_adapter *adapter, int address, int kind)
 {
-	struct i2c_client *new_client;
+	struct i2c_client *client;
 	struct pcf8591_data *data;
 	int err = 0;
 
@@ -205,12 +203,11 @@ static int pcf8591_detect(struct i2c_adapter *adapter, int address, int kind)
 		goto exit;
 	}
 	
-	new_client = &data->client;
-	i2c_set_clientdata(new_client, data);
-	new_client->addr = address;
-	new_client->adapter = adapter;
-	new_client->driver = &pcf8591_driver;
-	new_client->flags = 0;
+	client = &data->client;
+	i2c_set_clientdata(client, data);
+	client->addr = address;
+	client->adapter = adapter;
+	client->driver = &pcf8591_driver;
 
 	/* Now, we would do the remaining detection. But the PCF8591 is plainly
 	   impossible to detect! Stupid chip. */
@@ -221,31 +218,31 @@ static int pcf8591_detect(struct i2c_adapter *adapter, int address, int kind)
 
 	/* Fill in the remaining client fields and put it into the global 
 	   list */
-	strlcpy(new_client->name, "pcf8591", I2C_NAME_SIZE);
+	strlcpy(client->name, "pcf8591", I2C_NAME_SIZE);
 	mutex_init(&data->update_lock);
 
 	/* Tell the I2C layer a new client has arrived */
-	if ((err = i2c_attach_client(new_client)))
+	if ((err = i2c_attach_client(client)))
 		goto exit_kfree;
 
 	/* Initialize the PCF8591 chip */
-	pcf8591_init_client(new_client);
+	pcf8591_init_client(client);
 
 	/* Register sysfs hooks */
-	err = sysfs_create_group(&new_client->dev.kobj, &pcf8591_attr_group);
+	err = sysfs_create_group(&client->dev.kobj, &pcf8591_attr_group);
 	if (err)
 		goto exit_detach;
 
 	/* Register input2 if not in "two differential inputs" mode */
 	if (input_mode != 3) {
-		if ((err = device_create_file(&new_client->dev,
+		if ((err = device_create_file(&client->dev,
 					      &dev_attr_in2_input)))
 			goto exit_sysfs_remove;
 	}
 
 	/* Register input3 only in "four single ended inputs" mode */
 	if (input_mode == 0) {
-		if ((err = device_create_file(&new_client->dev,
+		if ((err = device_create_file(&client->dev,
 					      &dev_attr_in3_input)))
 			goto exit_sysfs_remove;
 	}
@@ -253,10 +250,10 @@ static int pcf8591_detect(struct i2c_adapter *adapter, int address, int kind)
 	return 0;
 
 exit_sysfs_remove:
-	sysfs_remove_group(&new_client->dev.kobj, &pcf8591_attr_group_opt);
-	sysfs_remove_group(&new_client->dev.kobj, &pcf8591_attr_group);
+	sysfs_remove_group(&client->dev.kobj, &pcf8591_attr_group_opt);
+	sysfs_remove_group(&client->dev.kobj, &pcf8591_attr_group);
 exit_detach:
-	i2c_detach_client(new_client);
+	i2c_detach_client(client);
 exit_kfree:
 	kfree(data);
 exit: