Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 106 insertions, 0 deletions

diff --git a/arch/v850/kernel/rte_ma1_cb.c b/arch/v850/kernel/rte_ma1_cb.c
new file mode 100644
index 000000000000..3873e276392f
--- /dev/null
+++ b/arch/v850/kernel/rte_ma1_cb.c
@@ -0,0 +1,106 @@
+/*
+ * arch/v850/kernel/rte_ma1_cb.c -- Midas labs RTE-V850E/MA1-CB board
+ *
+ *  Copyright (C) 2001,02,03  NEC Electronics Corporation
+ *  Copyright (C) 2001,02,03  Miles Bader <miles@gnu.org>
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License.  See the file COPYING in the main directory of this
+ * archive for more details.
+ *
+ * Written by Miles Bader <miles@gnu.org>
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/bootmem.h>
+
+#include <asm/atomic.h>
+#include <asm/page.h>
+#include <asm/ma1.h>
+#include <asm/rte_ma1_cb.h>
+#include <asm/v850e_timer_c.h>
+
+#include "mach.h"
+
+
+/* SRAM and SDRAM are almost contiguous (with a small hole in between;
+   see mach_reserve_bootmem for details), so just use both as one big area.  */
+#define RAM_START 	SRAM_ADDR
+#define RAM_END		(SDRAM_ADDR + SDRAM_SIZE)
+
+
+void __init mach_early_init (void)
+{
+	rte_cb_early_init ();
+}
+
+void __init mach_get_physical_ram (unsigned long *ram_start,
+				   unsigned long *ram_len)
+{
+	*ram_start = RAM_START;
+	*ram_len = RAM_END - RAM_START;
+}
+
+void __init mach_reserve_bootmem ()
+{
+#ifdef CONFIG_RTE_CB_MULTI
+	/* Prevent the kernel from touching the monitor's scratch RAM.  */
+	reserve_bootmem (MON_SCRATCH_ADDR, MON_SCRATCH_SIZE);
+#endif
+
+	/* The space between SRAM and SDRAM is filled with duplicate
+	   images of SRAM.  Prevent the kernel from using them.  */
+	reserve_bootmem (SRAM_ADDR + SRAM_SIZE,
+			 SDRAM_ADDR - (SRAM_ADDR + SRAM_SIZE));
+}
+
+void mach_gettimeofday (struct timespec *tv)
+{
+	tv->tv_sec = 0;
+	tv->tv_nsec = 0;
+}
+
+/* Called before configuring an on-chip UART.  */
+void rte_ma1_cb_uart_pre_configure (unsigned chan,
+				    unsigned cflags, unsigned baud)
+{
+	/* The RTE-MA1-CB connects some general-purpose I/O pins on the
+	   CPU to the RTS/CTS lines of UART 0's serial connection.
+	   I/O pins P42 and P43 are RTS and CTS respectively.  */
+	if (chan == 0) {
+		/* Put P42 & P43 in I/O port mode.  */
+		MA_PORT4_PMC &= ~0xC;
+		/* Make P42 an output, and P43 an input.  */
+		MA_PORT4_PM = (MA_PORT4_PM & ~0xC) | 0x8;
+	}
+
+	/* Do pre-configuration for the actual UART.  */
+	ma_uart_pre_configure (chan, cflags, baud);
+}
+
+void __init mach_init_irqs (void)
+{
+	unsigned tc;
+
+	/* Initialize interrupts.  */
+	ma_init_irqs ();
+	rte_cb_init_irqs ();
+
+	/* Use falling-edge-sensitivity for interrupts .  */
+	V850E_TIMER_C_SESC (0) &= ~0xC;
+	V850E_TIMER_C_SESC (1) &= ~0xF;
+
+	/* INTP000-INTP011 are shared with `Timer C', so we have to set
+	   up Timer C to pass them through as raw interrupts.  */
+	for (tc = 0; tc < 2; tc++)
+		/* Turn on the timer.  */
+		V850E_TIMER_C_TMCC0 (tc) |= V850E_TIMER_C_TMCC0_CAE;
+
+	/* Make sure the relevant port0/port1 pins are assigned
+	   interrupt duty.  We used INTP001-INTP011 (don't screw with
+	   INTP000 because the monitor uses it).  */
+	MA_PORT0_PMC |= 0x4;	/* P02 (INTP001) in IRQ mode.  */
+	MA_PORT1_PMC |= 0x6;	/* P11 (INTP010) & P12 (INTP011) in IRQ mode.*/
+}