[PATCH] powerpc: Add MPC834x SYS board to arch/powerpc

Add the first MPC83xx board that uses a flat device tree to arch/powerpc.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

1 files changed, 99 insertions, 0 deletions

diff --git a/arch/powerpc/platforms/83xx/pci.c b/arch/powerpc/platforms/83xx/pci.c
new file mode 100644
index 000000000000..469cdacc5bd4
--- /dev/null
+++ b/arch/powerpc/platforms/83xx/pci.c
@@ -0,0 +1,99 @@
+/*
+ * FSL SoC setup code
+ *
+ * Maintained by Kumar Gala (see MAINTAINERS for contact information)
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/config.h>
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+
+#include <asm/system.h>
+#include <asm/atomic.h>
+#include <asm/io.h>
+#include <asm/pci-bridge.h>
+#include <asm/prom.h>
+#include <sysdev/fsl_soc.h>
+
+#undef DEBUG
+
+#ifdef DEBUG
+#define DBG(x...) printk(x)
+#else
+#define DBG(x...)
+#endif
+
+int mpc83xx_pci2_busno;
+
+#ifdef CONFIG_PCI
+int __init add_bridge(struct device_node *dev)
+{
+	int len;
+	struct pci_controller *hose;
+	struct resource rsrc;
+	int *bus_range;
+	int primary = 1, has_address = 0;
+	phys_addr_t immr = get_immrbase();
+
+	DBG("Adding PCI host bridge %s\n", dev->full_name);
+
+	/* Fetch host bridge registers address */
+	has_address = (of_address_to_resource(dev, 0, &rsrc) == 0);
+
+	/* Get bus range if any */
+	bus_range = (int *) get_property(dev, "bus-range", &len);
+	if (bus_range == NULL || len < 2 * sizeof(int)) {
+		printk(KERN_WARNING "Can't get bus-range for %s, assume"
+		       " bus 0\n", dev->full_name);
+	}
+
+	hose = pcibios_alloc_controller();
+	if (!hose)
+		return -ENOMEM;
+	hose->arch_data = dev;
+	hose->set_cfg_type = 1;
+
+	hose->first_busno = bus_range ? bus_range[0] : 0;
+	hose->last_busno = bus_range ? bus_range[1] : 0xff;
+
+	/* MPC83xx supports up to two host controllers one at 0x8500 from immrbar
+	 * the other at 0x8600, we consider the 0x8500 the primary controller
+	 */
+	/* PCI 1 */
+	if ((rsrc.start & 0xfffff) == 0x8500) {
+		setup_indirect_pci(hose, immr + 0x8300, immr + 0x8304);
+	}
+	/* PCI 2*/
+	if ((rsrc.start & 0xfffff) == 0x8600) {
+		setup_indirect_pci(hose, immr + 0x8380, immr + 0x8384);
+		primary = 0;
+		hose->bus_offset = hose->first_busno;
+		mpc83xx_pci2_busno = hose->first_busno;
+	}
+
+	printk(KERN_INFO "Found MPC83xx PCI host bridge at 0x%08lx. "
+	       "Firmware bus number: %d->%d\n",
+		rsrc.start, hose->first_busno, hose->last_busno);
+
+	DBG(" ->Hose at 0x%p, cfg_addr=0x%p,cfg_data=0x%p\n",
+		hose, hose->cfg_addr, hose->cfg_data);
+
+	/* Interpret the "ranges" property */
+	/* This also maps the I/O region and sets isa_io/mem_base */
+	pci_process_bridge_OF_ranges(hose, dev, primary);
+
+	return 0;
+}
+
+#endif