spi/pl022: Add spi->mode support to AMBA SPI driver

This patch adds spi->mode support for the AMBA pl022 driver and
allows spidev to correctly alter SPI modes. Unused fields used in
the pl022 header file for the pl022_config_chip have been removed.

The ab8500 client driver selects the data transfer size instead
of the platform data.

For platforms that use the amba pl022 driver, the unused fields
in the controller data structure have been removed and the .mode
field in the SPI board info structure is used instead.

Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

2 files changed, 3 insertions, 12 deletions

diff --git a/arch/arm/mach-u300/dummyspichip.c b/arch/arm/mach-u300/dummyspichip.c
index 5f55012b7c9e..03f793612594 100644
--- a/arch/arm/mach-u300/dummyspichip.c
+++ b/arch/arm/mach-u300/dummyspichip.c
@@ -46,7 +46,6 @@ static ssize_t dummy_looptest(struct device *dev,
 	 * struct, this is just used here to alter the behaviour of the chip
 	 * in order to perform tests.
 	 */
-	struct pl022_config_chip *chip_info = spi->controller_data;
 	int status;
 	u8 txbuf[14] = {0xDE, 0xAD, 0xBE, 0xEF, 0x2B, 0xAD,
 			0xCA, 0xFE, 0xBA, 0xBE, 0xB1, 0x05,
@@ -72,7 +71,7 @@ static ssize_t dummy_looptest(struct device *dev,
 	 * Force chip to 8 bit mode
 	 * WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
 	 */
-	chip_info->data_size = SSP_DATA_BITS_8;
+	spi->bits_per_word = 8;
 	/* You should NOT DO THIS EITHER */
 	spi->master->setup(spi);
 
@@ -159,7 +158,7 @@ static ssize_t dummy_looptest(struct device *dev,
 	 * Force chip to 16 bit mode
 	 * WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
 	 */
-	chip_info->data_size = SSP_DATA_BITS_16;
+	spi->bits_per_word = 16;
 	/* You should NOT DO THIS EITHER */
 	spi->master->setup(spi);
 
diff --git a/arch/arm/mach-u300/spi.c b/arch/arm/mach-u300/spi.c
index f0e887bea30e..edb2c0d255c2 100644
--- a/arch/arm/mach-u300/spi.c
+++ b/arch/arm/mach-u300/spi.c
@@ -30,8 +30,6 @@ static void select_dummy_chip(u32 chipselect)
 }
 
 struct pl022_config_chip dummy_chip_info = {
-	/* Nominally this is LOOPBACK_DISABLED, but this is our dummy chip! */
-	.lbm = LOOPBACK_ENABLED,
 	/*
 	 * available POLLING_TRANSFER and INTERRUPT_TRANSFER,
 	 * DMA_TRANSFER does not work
@@ -42,14 +40,8 @@ struct pl022_config_chip dummy_chip_info = {
 	.hierarchy = SSP_MASTER,
 	/* 0 = drive TX even as slave, 1 = do not drive TX as slave */
 	.slave_tx_disable = 0,
-	/* LSB first */
-	.endian_tx = SSP_TX_LSB,
-	.endian_rx = SSP_RX_LSB,
-	.data_size = SSP_DATA_BITS_8, /* used to be 12 in some default */
 	.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
 	.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
-	.clk_phase = SSP_CLK_SECOND_EDGE,
-	.clk_pol = SSP_CLK_POL_IDLE_LOW,
 	.ctrl_len = SSP_BITS_12,
 	.wait_state = SSP_MWIRE_WAIT_ZERO,
 	.duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
@@ -75,7 +67,7 @@ static struct spi_board_info u300_spi_devices[] = {
 		.bus_num        = 0, /* Only one bus on this chip */
 		.chip_select    = 0,
 		/* Means SPI_CS_HIGH, change if e.g low CS */
-		.mode           = 0,
+		.mode           = SPI_MODE_1 | SPI_LSB_FIRST | SPI_LOOP,
 	},
 #endif
 };