ARM i.MX: Merge i.MX5 support into mach-imx

This patch moves the contents of arch/arm/mach-mx5 to arch/arm/mach-imx
and adjusts the Makefile/Kconfig entries in a way that it's possible
to compile i.MX5 together with i.MX3/6.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>

1 files changed, 338 insertions, 0 deletions

diff --git a/arch/arm/mach-imx/mach-cpuimx51sd.c b/arch/arm/mach-imx/mach-cpuimx51sd.c
new file mode 100644
index 000000000000..52a11c1898e6
--- /dev/null
+++ b/arch/arm/mach-imx/mach-cpuimx51sd.c
@@ -0,0 +1,338 @@
+/*
+ *
+ * Copyright (C) 2010 Eric Bénard <eric@eukrea.com>
+ *
+ * based on board-mx51_babbage.c which is
+ * Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria@canonical.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/i2c.h>
+#include <linux/i2c/tsc2007.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/i2c-gpio.h>
+#include <linux/spi/spi.h>
+#include <linux/can/platform/mcp251x.h>
+
+#include <mach/eukrea-baseboards.h>
+#include <mach/common.h>
+#include <mach/hardware.h>
+#include <mach/iomux-mx51.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+
+#include "devices-imx51.h"
+#include "cpu_op-mx51.h"
+
+#define USBH1_RST		IMX_GPIO_NR(2, 28)
+#define ETH_RST			IMX_GPIO_NR(2, 31)
+#define TSC2007_IRQGPIO		IMX_GPIO_NR(3, 12)
+#define CAN_IRQGPIO		IMX_GPIO_NR(1, 1)
+#define CAN_RST			IMX_GPIO_NR(4, 15)
+#define CAN_NCS			IMX_GPIO_NR(4, 24)
+#define CAN_RXOBF		IMX_GPIO_NR(1, 4)
+#define CAN_RX1BF		IMX_GPIO_NR(1, 6)
+#define CAN_TXORTS		IMX_GPIO_NR(1, 7)
+#define CAN_TX1RTS		IMX_GPIO_NR(1, 8)
+#define CAN_TX2RTS		IMX_GPIO_NR(1, 9)
+#define I2C_SCL			IMX_GPIO_NR(4, 16)
+#define I2C_SDA			IMX_GPIO_NR(4, 17)
+
+/* USB_CTRL_1 */
+#define MX51_USB_CTRL_1_OFFSET		0x10
+#define MX51_USB_CTRL_UH1_EXT_CLK_EN	(1 << 25)
+
+#define	MX51_USB_PLLDIV_12_MHZ		0x00
+#define	MX51_USB_PLL_DIV_19_2_MHZ	0x01
+#define	MX51_USB_PLL_DIV_24_MHZ		0x02
+
+static iomux_v3_cfg_t eukrea_cpuimx51sd_pads[] = {
+	/* UART1 */
+	MX51_PAD_UART1_RXD__UART1_RXD,
+	MX51_PAD_UART1_TXD__UART1_TXD,
+	MX51_PAD_UART1_RTS__UART1_RTS,
+	MX51_PAD_UART1_CTS__UART1_CTS,
+
+	/* USB HOST1 */
+	MX51_PAD_USBH1_CLK__USBH1_CLK,
+	MX51_PAD_USBH1_DIR__USBH1_DIR,
+	MX51_PAD_USBH1_NXT__USBH1_NXT,
+	MX51_PAD_USBH1_DATA0__USBH1_DATA0,
+	MX51_PAD_USBH1_DATA1__USBH1_DATA1,
+	MX51_PAD_USBH1_DATA2__USBH1_DATA2,
+	MX51_PAD_USBH1_DATA3__USBH1_DATA3,
+	MX51_PAD_USBH1_DATA4__USBH1_DATA4,
+	MX51_PAD_USBH1_DATA5__USBH1_DATA5,
+	MX51_PAD_USBH1_DATA6__USBH1_DATA6,
+	MX51_PAD_USBH1_DATA7__USBH1_DATA7,
+	MX51_PAD_USBH1_STP__USBH1_STP,
+	MX51_PAD_EIM_CS3__GPIO2_28,		/* PHY nRESET */
+
+	/* FEC */
+	MX51_PAD_EIM_DTACK__GPIO2_31,		/* PHY nRESET */
+
+	/* HSI2C */
+	MX51_PAD_I2C1_CLK__GPIO4_16,
+	MX51_PAD_I2C1_DAT__GPIO4_17,
+
+	/* CAN */
+	MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
+	MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
+	MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
+	MX51_PAD_CSPI1_SS0__GPIO4_24,		/* nCS */
+	MX51_PAD_CSI2_PIXCLK__GPIO4_15,		/* nReset */
+	MX51_PAD_GPIO1_1__GPIO1_1,		/* IRQ */
+	MX51_PAD_GPIO1_4__GPIO1_4,		/* Control signals */
+	MX51_PAD_GPIO1_6__GPIO1_6,
+	MX51_PAD_GPIO1_7__GPIO1_7,
+	MX51_PAD_GPIO1_8__GPIO1_8,
+	MX51_PAD_GPIO1_9__GPIO1_9,
+
+	/* Touchscreen */
+	/* IRQ */
+	NEW_PAD_CTRL(MX51_PAD_GPIO_NAND__GPIO_NAND, PAD_CTL_PUS_22K_UP |
+			PAD_CTL_PKE | PAD_CTL_SRE_FAST |
+			PAD_CTL_DSE_HIGH | PAD_CTL_PUE | PAD_CTL_HYS),
+};
+
+static const struct imxuart_platform_data uart_pdata __initconst = {
+	.flags = IMXUART_HAVE_RTSCTS,
+};
+
+static struct tsc2007_platform_data tsc2007_info = {
+	.model			= 2007,
+	.x_plate_ohms		= 180,
+};
+
+static struct i2c_board_info eukrea_cpuimx51sd_i2c_devices[] = {
+	{
+		I2C_BOARD_INFO("pcf8563", 0x51),
+	}, {
+		I2C_BOARD_INFO("tsc2007", 0x49),
+		.type		= "tsc2007",
+		.platform_data	= &tsc2007_info,
+		.irq		= IMX_GPIO_TO_IRQ(TSC2007_IRQGPIO),
+	},
+};
+
+static const struct mxc_nand_platform_data
+		eukrea_cpuimx51sd_nand_board_info __initconst = {
+	.width		= 1,
+	.hw_ecc		= 1,
+	.flash_bbt	= 1,
+};
+
+/* This function is board specific as the bit mask for the plldiv will also
+be different for other Freescale SoCs, thus a common bitmask is not
+possible and cannot get place in /plat-mxc/ehci.c.*/
+static int initialize_otg_port(struct platform_device *pdev)
+{
+	u32 v;
+	void __iomem *usb_base;
+	void __iomem *usbother_base;
+
+	usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
+	if (!usb_base)
+		return -ENOMEM;
+	usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
+
+	/* Set the PHY clock to 19.2MHz */
+	v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
+	v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
+	v |= MX51_USB_PLL_DIV_19_2_MHZ;
+	__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
+	iounmap(usb_base);
+
+	mdelay(10);
+
+	return mx51_initialize_usb_hw(0, MXC_EHCI_INTERNAL_PHY);
+}
+
+static int initialize_usbh1_port(struct platform_device *pdev)
+{
+	u32 v;
+	void __iomem *usb_base;
+	void __iomem *usbother_base;
+
+	usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
+	if (!usb_base)
+		return -ENOMEM;
+	usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
+
+	/* The clock for the USBH1 ULPI port will come from the PHY. */
+	v = __raw_readl(usbother_base + MX51_USB_CTRL_1_OFFSET);
+	__raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN,
+			usbother_base + MX51_USB_CTRL_1_OFFSET);
+	iounmap(usb_base);
+
+	mdelay(10);
+
+	return mx51_initialize_usb_hw(1, MXC_EHCI_POWER_PINS_ENABLED |
+			MXC_EHCI_ITC_NO_THRESHOLD);
+}
+
+static const struct mxc_usbh_platform_data dr_utmi_config __initconst = {
+	.init		= initialize_otg_port,
+	.portsc	= MXC_EHCI_UTMI_16BIT,
+};
+
+static const struct fsl_usb2_platform_data usb_pdata __initconst = {
+	.operating_mode	= FSL_USB2_DR_DEVICE,
+	.phy_mode	= FSL_USB2_PHY_UTMI_WIDE,
+};
+
+static const struct mxc_usbh_platform_data usbh1_config __initconst = {
+	.init		= initialize_usbh1_port,
+	.portsc	= MXC_EHCI_MODE_ULPI,
+};
+
+static int otg_mode_host;
+
+static int __init eukrea_cpuimx51sd_otg_mode(char *options)
+{
+	if (!strcmp(options, "host"))
+		otg_mode_host = 1;
+	else if (!strcmp(options, "device"))
+		otg_mode_host = 0;
+	else
+		pr_info("otg_mode neither \"host\" nor \"device\". "
+			"Defaulting to device\n");
+	return 0;
+}
+__setup("otg_mode=", eukrea_cpuimx51sd_otg_mode);
+
+static struct i2c_gpio_platform_data pdata = {
+	.sda_pin		= I2C_SDA,
+	.sda_is_open_drain	= 0,
+	.scl_pin		= I2C_SCL,
+	.scl_is_open_drain	= 0,
+	.udelay			= 2,
+};
+
+static struct platform_device hsi2c_gpio_device = {
+	.name			= "i2c-gpio",
+	.id			= 0,
+	.dev.platform_data	= &pdata,
+};
+
+static struct mcp251x_platform_data mcp251x_info = {
+	.oscillator_frequency = 24E6,
+};
+
+static struct spi_board_info cpuimx51sd_spi_device[] = {
+	{
+		.modalias        = "mcp2515",
+		.max_speed_hz    = 10000000,
+		.bus_num         = 0,
+		.mode		= SPI_MODE_0,
+		.chip_select     = 0,
+		.platform_data   = &mcp251x_info,
+		.irq             = IMX_GPIO_TO_IRQ(CAN_IRQGPIO)
+	},
+};
+
+static int cpuimx51sd_spi1_cs[] = {
+	CAN_NCS,
+};
+
+static const struct spi_imx_master cpuimx51sd_ecspi1_pdata __initconst = {
+	.chipselect	= cpuimx51sd_spi1_cs,
+	.num_chipselect	= ARRAY_SIZE(cpuimx51sd_spi1_cs),
+};
+
+static struct platform_device *platform_devices[] __initdata = {
+	&hsi2c_gpio_device,
+};
+
+static void __init eukrea_cpuimx51sd_init(void)
+{
+	imx51_soc_init();
+
+	mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx51sd_pads,
+					ARRAY_SIZE(eukrea_cpuimx51sd_pads));
+
+#if defined(CONFIG_CPU_FREQ_IMX)
+	get_cpu_op = mx51_get_cpu_op;
+#endif
+
+	imx51_add_imx_uart(0, &uart_pdata);
+	imx51_add_mxc_nand(&eukrea_cpuimx51sd_nand_board_info);
+
+	gpio_request(ETH_RST, "eth_rst");
+	gpio_set_value(ETH_RST, 1);
+	imx51_add_fec(NULL);
+
+	gpio_request(CAN_IRQGPIO, "can_irq");
+	gpio_direction_input(CAN_IRQGPIO);
+	gpio_free(CAN_IRQGPIO);
+	gpio_request(CAN_NCS, "can_ncs");
+	gpio_direction_output(CAN_NCS, 1);
+	gpio_free(CAN_NCS);
+	gpio_request(CAN_RST, "can_rst");
+	gpio_direction_output(CAN_RST, 0);
+	msleep(20);
+	gpio_set_value(CAN_RST, 1);
+	imx51_add_ecspi(0, &cpuimx51sd_ecspi1_pdata);
+	spi_register_board_info(cpuimx51sd_spi_device,
+				ARRAY_SIZE(cpuimx51sd_spi_device));
+
+	gpio_request(TSC2007_IRQGPIO, "tsc2007_irq");
+	gpio_direction_input(TSC2007_IRQGPIO);
+	gpio_free(TSC2007_IRQGPIO);
+
+	i2c_register_board_info(0, eukrea_cpuimx51sd_i2c_devices,
+			ARRAY_SIZE(eukrea_cpuimx51sd_i2c_devices));
+	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
+
+	if (otg_mode_host)
+		imx51_add_mxc_ehci_otg(&dr_utmi_config);
+	else {
+		initialize_otg_port(NULL);
+		imx51_add_fsl_usb2_udc(&usb_pdata);
+	}
+
+	gpio_request(USBH1_RST, "usb_rst");
+	gpio_direction_output(USBH1_RST, 0);
+	msleep(20);
+	gpio_set_value(USBH1_RST, 1);
+	imx51_add_mxc_ehci_hs(1, &usbh1_config);
+
+#ifdef CONFIG_MACH_EUKREA_MBIMXSD51_BASEBOARD
+	eukrea_mbimxsd51_baseboard_init();
+#endif
+}
+
+static void __init eukrea_cpuimx51sd_timer_init(void)
+{
+	mx51_clocks_init(32768, 24000000, 22579200, 0);
+}
+
+static struct sys_timer mxc_timer = {
+	.init	= eukrea_cpuimx51sd_timer_init,
+};
+
+MACHINE_START(EUKREA_CPUIMX51SD, "Eukrea CPUIMX51SD")
+	/* Maintainer: Eric Bénard <eric@eukrea.com> */
+	.atag_offset = 0x100,
+	.map_io = mx51_map_io,
+	.init_early = imx51_init_early,
+	.init_irq = mx51_init_irq,
+	.handle_irq = imx51_handle_irq,
+	.timer = &mxc_timer,
+	.init_machine = eukrea_cpuimx51sd_init,
+MACHINE_END