Merge branch 'linus' into x86/tracehook

Conflicts:
	arch/x86/Kconfig

Signed-off-by: Ingo Molnar <mingo@elte.hu>

1 files changed, 581 insertions, 0 deletions

diff --git a/arch/arm/include/asm/hardware/sa1111.h b/arch/arm/include/asm/hardware/sa1111.h
new file mode 100644
index 000000000000..5da2595759e5
--- /dev/null
+++ b/arch/arm/include/asm/hardware/sa1111.h
@@ -0,0 +1,581 @@
+/*
+ * arch/arm/include/asm/hardware/sa1111.h
+ *
+ * Copyright (C) 2000 John G Dorsey <john+@cs.cmu.edu>
+ *
+ * This file contains definitions for the SA-1111 Companion Chip.
+ * (Structure and naming borrowed from SA-1101.h, by Peter Danielsson.)
+ *
+ * Macro that calculates real address for registers in the SA-1111
+ */
+
+#ifndef _ASM_ARCH_SA1111
+#define _ASM_ARCH_SA1111
+
+#include <mach/bitfield.h>
+
+/*
+ * The SA1111 is always located at virtual 0xf4000000, and is always
+ * "native" endian.
+ */
+
+#define SA1111_VBASE		0xf4000000
+
+/* Don't use these! */
+#define SA1111_p2v( x )         ((x) - SA1111_BASE + SA1111_VBASE)
+#define SA1111_v2p( x )         ((x) - SA1111_VBASE + SA1111_BASE)
+
+#ifndef __ASSEMBLY__
+#define _SA1111(x)	((x) + sa1111->resource.start)
+#endif
+
+#define sa1111_writel(val,addr)	__raw_writel(val, addr)
+#define sa1111_readl(addr)	__raw_readl(addr)
+
+/*
+ * 26 bits of the SA-1110 address bus are available to the SA-1111.
+ * Use these when feeding target addresses to the DMA engines.
+ */
+
+#define SA1111_ADDR_WIDTH	(26)
+#define SA1111_ADDR_MASK	((1<<SA1111_ADDR_WIDTH)-1)
+#define SA1111_DMA_ADDR(x)	((x)&SA1111_ADDR_MASK)
+
+/*
+ * Don't ask the (SAC) DMA engines to move less than this amount.
+ */
+
+#define SA1111_SAC_DMA_MIN_XFER	(0x800)
+
+/*
+ * System Bus Interface (SBI)
+ *
+ * Registers
+ *    SKCR	Control Register
+ *    SMCR	Shared Memory Controller Register
+ *    SKID	ID Register
+ */
+#define SA1111_SKCR	0x0000
+#define SA1111_SMCR	0x0004
+#define SA1111_SKID	0x0008
+
+#define SKCR_PLL_BYPASS	(1<<0)
+#define SKCR_RCLKEN	(1<<1)
+#define SKCR_SLEEP	(1<<2)
+#define SKCR_DOZE	(1<<3)
+#define SKCR_VCO_OFF	(1<<4)
+#define SKCR_SCANTSTEN	(1<<5)
+#define SKCR_CLKTSTEN	(1<<6)
+#define SKCR_RDYEN	(1<<7)
+#define SKCR_SELAC	(1<<8)
+#define SKCR_OPPC	(1<<9)
+#define SKCR_PLLTSTEN	(1<<10)
+#define SKCR_USBIOTSTEN	(1<<11)
+/*
+ * Don't believe the specs!  Take them, throw them outside.  Leave them
+ * there for a week.  Spit on them.  Walk on them.  Stamp on them.
+ * Pour gasoline over them and finally burn them.  Now think about coding.
+ *  - The October 1999 errata (278260-007) says its bit 13, 1 to enable.
+ *  - The Feb 2001 errata (278260-010) says that the previous errata
+ *    (278260-009) is wrong, and its bit actually 12, fixed in spec
+ *    278242-003.
+ *  - The SA1111 manual (278242) says bit 12, but 0 to enable.
+ *  - Reality is bit 13, 1 to enable.
+ *      -- rmk
+ */
+#define SKCR_OE_EN	(1<<13)
+
+#define SMCR_DTIM	(1<<0)
+#define SMCR_MBGE	(1<<1)
+#define SMCR_DRAC_0	(1<<2)
+#define SMCR_DRAC_1	(1<<3)
+#define SMCR_DRAC_2	(1<<4)
+#define SMCR_DRAC	Fld(3, 2)
+#define SMCR_CLAT	(1<<5)
+
+#define SKID_SIREV_MASK	(0x000000f0)
+#define SKID_MTREV_MASK (0x0000000f)
+#define SKID_ID_MASK	(0xffffff00)
+#define SKID_SA1111_ID	(0x690cc200)
+
+/*
+ * System Controller
+ *
+ * Registers
+ *    SKPCR	Power Control Register
+ *    SKCDR	Clock Divider Register
+ *    SKAUD	Audio Clock Divider Register
+ *    SKPMC	PS/2 Mouse Clock Divider Register
+ *    SKPTC	PS/2 Track Pad Clock Divider Register
+ *    SKPEN0	PWM0 Enable Register
+ *    SKPWM0	PWM0 Clock Register
+ *    SKPEN1	PWM1 Enable Register
+ *    SKPWM1	PWM1 Clock Register
+ */
+#define SA1111_SKPCR	0x0200
+#define SA1111_SKCDR	0x0204
+#define SA1111_SKAUD	0x0208
+#define SA1111_SKPMC	0x020c
+#define SA1111_SKPTC	0x0210
+#define SA1111_SKPEN0	0x0214
+#define SA1111_SKPWM0	0x0218
+#define SA1111_SKPEN1	0x021c
+#define SA1111_SKPWM1	0x0220
+
+#define SKPCR_UCLKEN	(1<<0)
+#define SKPCR_ACCLKEN	(1<<1)
+#define SKPCR_I2SCLKEN	(1<<2)
+#define SKPCR_L3CLKEN	(1<<3)
+#define SKPCR_SCLKEN	(1<<4)
+#define SKPCR_PMCLKEN	(1<<5)
+#define SKPCR_PTCLKEN	(1<<6)
+#define SKPCR_DCLKEN	(1<<7)
+#define SKPCR_PWMCLKEN	(1<<8)
+
+/*
+ * USB Host controller
+ */
+#define SA1111_USB		0x0400
+
+/*
+ * Offsets from SA1111_USB_BASE
+ */
+#define SA1111_USB_STATUS	0x0118
+#define SA1111_USB_RESET	0x011c
+#define SA1111_USB_IRQTEST	0x0120
+
+#define USB_RESET_FORCEIFRESET	(1 << 0)
+#define USB_RESET_FORCEHCRESET	(1 << 1)
+#define USB_RESET_CLKGENRESET	(1 << 2)
+#define USB_RESET_SIMSCALEDOWN	(1 << 3)
+#define USB_RESET_USBINTTEST	(1 << 4)
+#define USB_RESET_SLEEPSTBYEN	(1 << 5)
+#define USB_RESET_PWRSENSELOW	(1 << 6)
+#define USB_RESET_PWRCTRLLOW	(1 << 7)
+
+#define USB_STATUS_IRQHCIRMTWKUP  (1 <<  7)
+#define USB_STATUS_IRQHCIBUFFACC  (1 <<  8)
+#define USB_STATUS_NIRQHCIM       (1 <<  9)
+#define USB_STATUS_NHCIMFCLR      (1 << 10)
+#define USB_STATUS_USBPWRSENSE    (1 << 11)
+
+/*
+ * Serial Audio Controller
+ *
+ * Registers
+ *    SACR0             Serial Audio Common Control Register
+ *    SACR1             Serial Audio Alternate Mode (I2C/MSB) Control Register
+ *    SACR2             Serial Audio AC-link Control Register
+ *    SASR0             Serial Audio I2S/MSB Interface & FIFO Status Register
+ *    SASR1             Serial Audio AC-link Interface & FIFO Status Register
+ *    SASCR             Serial Audio Status Clear Register
+ *    L3_CAR            L3 Control Bus Address Register
+ *    L3_CDR            L3 Control Bus Data Register
+ *    ACCAR             AC-link Command Address Register
+ *    ACCDR             AC-link Command Data Register
+ *    ACSAR             AC-link Status Address Register
+ *    ACSDR             AC-link Status Data Register
+ *    SADTCS            Serial Audio DMA Transmit Control/Status Register
+ *    SADTSA            Serial Audio DMA Transmit Buffer Start Address A
+ *    SADTCA            Serial Audio DMA Transmit Buffer Count Register A
+ *    SADTSB            Serial Audio DMA Transmit Buffer Start Address B
+ *    SADTCB            Serial Audio DMA Transmit Buffer Count Register B
+ *    SADRCS            Serial Audio DMA Receive Control/Status Register
+ *    SADRSA            Serial Audio DMA Receive Buffer Start Address A
+ *    SADRCA            Serial Audio DMA Receive Buffer Count Register A
+ *    SADRSB            Serial Audio DMA Receive Buffer Start Address B
+ *    SADRCB            Serial Audio DMA Receive Buffer Count Register B
+ *    SAITR             Serial Audio Interrupt Test Register
+ *    SADR              Serial Audio Data Register (16 x 32-bit)
+ */
+
+#define SA1111_SERAUDIO		0x0600
+
+/*
+ * These are offsets from the above base.
+ */
+#define SA1111_SACR0		0x00
+#define SA1111_SACR1		0x04
+#define SA1111_SACR2		0x08
+#define SA1111_SASR0		0x0c
+#define SA1111_SASR1		0x10
+#define SA1111_SASCR		0x18
+#define SA1111_L3_CAR		0x1c
+#define SA1111_L3_CDR		0x20
+#define SA1111_ACCAR		0x24
+#define SA1111_ACCDR		0x28
+#define SA1111_ACSAR		0x2c
+#define SA1111_ACSDR		0x30
+#define SA1111_SADTCS		0x34
+#define SA1111_SADTSA		0x38
+#define SA1111_SADTCA		0x3c
+#define SA1111_SADTSB		0x40
+#define SA1111_SADTCB		0x44
+#define SA1111_SADRCS		0x48
+#define SA1111_SADRSA		0x4c
+#define SA1111_SADRCA		0x50
+#define SA1111_SADRSB		0x54
+#define SA1111_SADRCB		0x58
+#define SA1111_SAITR		0x5c
+#define SA1111_SADR		0x80
+
+#ifndef CONFIG_ARCH_PXA
+
+#define SACR0_ENB	(1<<0)
+#define SACR0_BCKD	(1<<2)
+#define SACR0_RST	(1<<3)
+
+#define SACR1_AMSL	(1<<0)
+#define SACR1_L3EN	(1<<1)
+#define SACR1_L3MB	(1<<2)
+#define SACR1_DREC	(1<<3)
+#define SACR1_DRPL	(1<<4)
+#define SACR1_ENLBF	(1<<5)
+
+#define SACR2_TS3V	(1<<0)
+#define SACR2_TS4V	(1<<1)
+#define SACR2_WKUP	(1<<2)
+#define SACR2_DREC	(1<<3)
+#define SACR2_DRPL	(1<<4)
+#define SACR2_ENLBF	(1<<5)
+#define SACR2_RESET	(1<<6)
+
+#define SASR0_TNF	(1<<0)
+#define SASR0_RNE	(1<<1)
+#define SASR0_BSY	(1<<2)
+#define SASR0_TFS	(1<<3)
+#define SASR0_RFS	(1<<4)
+#define SASR0_TUR	(1<<5)
+#define SASR0_ROR	(1<<6)
+#define SASR0_L3WD	(1<<16)
+#define SASR0_L3RD	(1<<17)
+
+#define SASR1_TNF	(1<<0)
+#define SASR1_RNE	(1<<1)
+#define SASR1_BSY	(1<<2)
+#define SASR1_TFS	(1<<3)
+#define SASR1_RFS	(1<<4)
+#define SASR1_TUR	(1<<5)
+#define SASR1_ROR	(1<<6)
+#define SASR1_CADT	(1<<16)
+#define SASR1_SADR	(1<<17)
+#define SASR1_RSTO	(1<<18)
+#define SASR1_CLPM	(1<<19)
+#define SASR1_CRDY	(1<<20)
+#define SASR1_RS3V	(1<<21)
+#define SASR1_RS4V	(1<<22)
+
+#define SASCR_TUR	(1<<5)
+#define SASCR_ROR	(1<<6)
+#define SASCR_DTS	(1<<16)
+#define SASCR_RDD	(1<<17)
+#define SASCR_STO	(1<<18)
+
+#define SADTCS_TDEN	(1<<0)
+#define SADTCS_TDIE	(1<<1)
+#define SADTCS_TDBDA	(1<<3)
+#define SADTCS_TDSTA	(1<<4)
+#define SADTCS_TDBDB	(1<<5)
+#define SADTCS_TDSTB	(1<<6)
+#define SADTCS_TBIU	(1<<7)
+
+#define SADRCS_RDEN	(1<<0)
+#define SADRCS_RDIE	(1<<1)
+#define SADRCS_RDBDA	(1<<3)
+#define SADRCS_RDSTA	(1<<4)
+#define SADRCS_RDBDB	(1<<5)
+#define SADRCS_RDSTB	(1<<6)
+#define SADRCS_RBIU	(1<<7)
+
+#define SAD_CS_DEN	(1<<0)
+#define SAD_CS_DIE	(1<<1)	/* Not functional on metal 1 */
+#define SAD_CS_DBDA	(1<<3)	/* Not functional on metal 1 */
+#define SAD_CS_DSTA	(1<<4)
+#define SAD_CS_DBDB	(1<<5)	/* Not functional on metal 1 */
+#define SAD_CS_DSTB	(1<<6)
+#define SAD_CS_BIU	(1<<7)	/* Not functional on metal 1 */
+
+#define SAITR_TFS	(1<<0)
+#define SAITR_RFS	(1<<1)
+#define SAITR_TUR	(1<<2)
+#define SAITR_ROR	(1<<3)
+#define SAITR_CADT	(1<<4)
+#define SAITR_SADR	(1<<5)
+#define SAITR_RSTO	(1<<6)
+#define SAITR_TDBDA	(1<<8)
+#define SAITR_TDBDB	(1<<9)
+#define SAITR_RDBDA	(1<<10)
+#define SAITR_RDBDB	(1<<11)
+
+#endif  /* !CONFIG_ARCH_PXA */
+
+/*
+ * General-Purpose I/O Interface
+ *
+ * Registers
+ *    PA_DDR		GPIO Block A Data Direction
+ *    PA_DRR/PA_DWR	GPIO Block A Data Value Register (read/write)
+ *    PA_SDR		GPIO Block A Sleep Direction
+ *    PA_SSR		GPIO Block A Sleep State
+ *    PB_DDR		GPIO Block B Data Direction
+ *    PB_DRR/PB_DWR	GPIO Block B Data Value Register (read/write)
+ *    PB_SDR		GPIO Block B Sleep Direction
+ *    PB_SSR		GPIO Block B Sleep State
+ *    PC_DDR		GPIO Block C Data Direction
+ *    PC_DRR/PC_DWR	GPIO Block C Data Value Register (read/write)
+ *    PC_SDR		GPIO Block C Sleep Direction
+ *    PC_SSR		GPIO Block C Sleep State
+ */
+
+#define _PA_DDR		_SA1111( 0x1000 )
+#define _PA_DRR		_SA1111( 0x1004 )
+#define _PA_DWR		_SA1111( 0x1004 )
+#define _PA_SDR		_SA1111( 0x1008 )
+#define _PA_SSR		_SA1111( 0x100c )
+#define _PB_DDR		_SA1111( 0x1010 )
+#define _PB_DRR		_SA1111( 0x1014 )
+#define _PB_DWR		_SA1111( 0x1014 )
+#define _PB_SDR		_SA1111( 0x1018 )
+#define _PB_SSR		_SA1111( 0x101c )
+#define _PC_DDR		_SA1111( 0x1020 )
+#define _PC_DRR		_SA1111( 0x1024 )
+#define _PC_DWR		_SA1111( 0x1024 )
+#define _PC_SDR		_SA1111( 0x1028 )
+#define _PC_SSR		_SA1111( 0x102c )
+
+#define SA1111_GPIO	0x1000
+
+#define SA1111_GPIO_PADDR	(0x000)
+#define SA1111_GPIO_PADRR	(0x004)
+#define SA1111_GPIO_PADWR	(0x004)
+#define SA1111_GPIO_PASDR	(0x008)
+#define SA1111_GPIO_PASSR	(0x00c)
+#define SA1111_GPIO_PBDDR	(0x010)
+#define SA1111_GPIO_PBDRR	(0x014)
+#define SA1111_GPIO_PBDWR	(0x014)
+#define SA1111_GPIO_PBSDR	(0x018)
+#define SA1111_GPIO_PBSSR	(0x01c)
+#define SA1111_GPIO_PCDDR	(0x020)
+#define SA1111_GPIO_PCDRR	(0x024)
+#define SA1111_GPIO_PCDWR	(0x024)
+#define SA1111_GPIO_PCSDR	(0x028)
+#define SA1111_GPIO_PCSSR	(0x02c)
+
+#define GPIO_A0		(1 << 0)
+#define GPIO_A1		(1 << 1)
+#define GPIO_A2		(1 << 2)
+#define GPIO_A3		(1 << 3)
+
+#define GPIO_B0		(1 << 8)
+#define GPIO_B1		(1 << 9)
+#define GPIO_B2		(1 << 10)
+#define GPIO_B3		(1 << 11)
+#define GPIO_B4		(1 << 12)
+#define GPIO_B5		(1 << 13)
+#define GPIO_B6		(1 << 14)
+#define GPIO_B7		(1 << 15)
+
+#define GPIO_C0		(1 << 16)
+#define GPIO_C1		(1 << 17)
+#define GPIO_C2		(1 << 18)
+#define GPIO_C3		(1 << 19)
+#define GPIO_C4		(1 << 20)
+#define GPIO_C5		(1 << 21)
+#define GPIO_C6		(1 << 22)
+#define GPIO_C7		(1 << 23)
+
+/*
+ * Interrupt Controller
+ *
+ * Registers
+ *    INTTEST0		Test register 0
+ *    INTTEST1		Test register 1
+ *    INTEN0		Interrupt Enable register 0
+ *    INTEN1		Interrupt Enable register 1
+ *    INTPOL0		Interrupt Polarity selection 0
+ *    INTPOL1		Interrupt Polarity selection 1
+ *    INTTSTSEL		Interrupt source selection
+ *    INTSTATCLR0	Interrupt Status/Clear 0
+ *    INTSTATCLR1	Interrupt Status/Clear 1
+ *    INTSET0		Interrupt source set 0
+ *    INTSET1		Interrupt source set 1
+ *    WAKE_EN0		Wake-up source enable 0
+ *    WAKE_EN1		Wake-up source enable 1
+ *    WAKE_POL0		Wake-up polarity selection 0
+ *    WAKE_POL1		Wake-up polarity selection 1
+ */
+#define SA1111_INTC		0x1600
+
+/*
+ * These are offsets from the above base.
+ */
+#define SA1111_INTTEST0		0x0000
+#define SA1111_INTTEST1		0x0004
+#define SA1111_INTEN0		0x0008
+#define SA1111_INTEN1		0x000c
+#define SA1111_INTPOL0		0x0010
+#define SA1111_INTPOL1		0x0014
+#define SA1111_INTTSTSEL	0x0018
+#define SA1111_INTSTATCLR0	0x001c
+#define SA1111_INTSTATCLR1	0x0020
+#define SA1111_INTSET0		0x0024
+#define SA1111_INTSET1		0x0028
+#define SA1111_WAKEEN0		0x002c
+#define SA1111_WAKEEN1		0x0030
+#define SA1111_WAKEPOL0		0x0034
+#define SA1111_WAKEPOL1		0x0038
+
+/*
+ * PS/2 Trackpad and Mouse Interfaces
+ *
+ * Registers
+ *    PS2CR		Control Register
+ *    PS2STAT		Status Register
+ *    PS2DATA		Transmit/Receive Data register
+ *    PS2CLKDIV		Clock Division Register
+ *    PS2PRECNT		Clock Precount Register
+ *    PS2TEST1		Test register 1
+ *    PS2TEST2		Test register 2
+ *    PS2TEST3		Test register 3
+ *    PS2TEST4		Test register 4
+ */
+
+#define SA1111_KBD		0x0a00
+#define SA1111_MSE		0x0c00
+
+/*
+ * These are offsets from the above bases.
+ */
+#define SA1111_PS2CR		0x0000
+#define SA1111_PS2STAT		0x0004
+#define SA1111_PS2DATA		0x0008
+#define SA1111_PS2CLKDIV	0x000c
+#define SA1111_PS2PRECNT	0x0010
+
+#define PS2CR_ENA		0x08
+#define PS2CR_FKD		0x02
+#define PS2CR_FKC		0x01
+
+#define PS2STAT_STP		0x0100
+#define PS2STAT_TXE		0x0080
+#define PS2STAT_TXB		0x0040
+#define PS2STAT_RXF		0x0020
+#define PS2STAT_RXB		0x0010
+#define PS2STAT_ENA		0x0008
+#define PS2STAT_RXP		0x0004
+#define PS2STAT_KBD		0x0002
+#define PS2STAT_KBC		0x0001
+
+/*
+ * PCMCIA Interface
+ *
+ * Registers
+ *    PCSR	Status Register
+ *    PCCR	Control Register
+ *    PCSSR	Sleep State Register
+ */
+
+#define SA1111_PCMCIA	0x1600
+
+/*
+ * These are offsets from the above base.
+ */
+#define SA1111_PCCR	0x0000
+#define SA1111_PCSSR	0x0004
+#define SA1111_PCSR	0x0008
+
+#define PCSR_S0_READY	(1<<0)
+#define PCSR_S1_READY	(1<<1)
+#define PCSR_S0_DETECT	(1<<2)
+#define PCSR_S1_DETECT	(1<<3)
+#define PCSR_S0_VS1	(1<<4)
+#define PCSR_S0_VS2	(1<<5)
+#define PCSR_S1_VS1	(1<<6)
+#define PCSR_S1_VS2	(1<<7)
+#define PCSR_S0_WP	(1<<8)
+#define PCSR_S1_WP	(1<<9)
+#define PCSR_S0_BVD1	(1<<10)
+#define PCSR_S0_BVD2	(1<<11)
+#define PCSR_S1_BVD1	(1<<12)
+#define PCSR_S1_BVD2	(1<<13)
+
+#define PCCR_S0_RST	(1<<0)
+#define PCCR_S1_RST	(1<<1)
+#define PCCR_S0_FLT	(1<<2)
+#define PCCR_S1_FLT	(1<<3)
+#define PCCR_S0_PWAITEN	(1<<4)
+#define PCCR_S1_PWAITEN	(1<<5)
+#define PCCR_S0_PSE	(1<<6)
+#define PCCR_S1_PSE	(1<<7)
+
+#define PCSSR_S0_SLEEP	(1<<0)
+#define PCSSR_S1_SLEEP	(1<<1)
+
+
+
+
+extern struct bus_type sa1111_bus_type;
+
+#define SA1111_DEVID_SBI	0
+#define SA1111_DEVID_SK		1
+#define SA1111_DEVID_USB	2
+#define SA1111_DEVID_SAC	3
+#define SA1111_DEVID_SSP	4
+#define SA1111_DEVID_PS2	5
+#define SA1111_DEVID_GPIO	6
+#define SA1111_DEVID_INT	7
+#define SA1111_DEVID_PCMCIA	8
+
+struct sa1111_dev {
+	struct device	dev;
+	unsigned int	devid;
+	struct resource	res;
+	void __iomem	*mapbase;
+	unsigned int	skpcr_mask;
+	unsigned int	irq[6];
+	u64		dma_mask;
+};
+
+#define SA1111_DEV(_d)	container_of((_d), struct sa1111_dev, dev)
+
+#define sa1111_get_drvdata(d)	dev_get_drvdata(&(d)->dev)
+#define sa1111_set_drvdata(d,p)	dev_set_drvdata(&(d)->dev, p)
+
+struct sa1111_driver {
+	struct device_driver	drv;
+	unsigned int		devid;
+	int (*probe)(struct sa1111_dev *);
+	int (*remove)(struct sa1111_dev *);
+	int (*suspend)(struct sa1111_dev *, pm_message_t);
+	int (*resume)(struct sa1111_dev *);
+};
+
+#define SA1111_DRV(_d)	container_of((_d), struct sa1111_driver, drv)
+
+#define SA1111_DRIVER_NAME(_sadev) ((_sadev)->dev.driver->name)
+
+/*
+ * These frob the SKPCR register.
+ */
+void sa1111_enable_device(struct sa1111_dev *);
+void sa1111_disable_device(struct sa1111_dev *);
+
+unsigned int sa1111_pll_clock(struct sa1111_dev *);
+
+#define SA1111_AUDIO_ACLINK	0
+#define SA1111_AUDIO_I2S	1
+
+void sa1111_select_audio_mode(struct sa1111_dev *sadev, int mode);
+int sa1111_set_audio_rate(struct sa1111_dev *sadev, int rate);
+int sa1111_get_audio_rate(struct sa1111_dev *sadev);
+
+int sa1111_check_dma_bug(dma_addr_t addr);
+
+int sa1111_driver_register(struct sa1111_driver *);
+void sa1111_driver_unregister(struct sa1111_driver *);
+
+void sa1111_set_io_dir(struct sa1111_dev *sadev, unsigned int bits, unsigned int dir, unsigned int sleep_dir);
+void sa1111_set_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v);
+void sa1111_set_sleep_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v);
+
+#endif  /* _ASM_ARCH_SA1111 */