Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC DT updates from Kevin Hilman:
 "As usual, quite a few device-tree updates in ARM land.  There was one
  minor churn in DTs due to relicensing under a dual-license, and lots
  of little additions of new peripherals, features etc, but nothing
  really exciting to call to your attention.  Some higlights, focsuing
  on support for new SoCs and boards:

   - AT91: new boards: Overkiz,  Acme Systems' Arietta G25
   - tegra: HDA support
   - bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS
     RT-AC87U
   - mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
     boards, DLink DNS-327L
   - OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill
     SL50
   - ARM: added support for Juno r1 board
   - sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33,
     Mele A1000G
   - imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
     Gateworks GW5510, and aristainetos2 boards
   - hisilicon: hi6220 SoC support; new boards: 96boards hikey"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (462 commits)
  ARM: hisi: revert changes from hisi/hip04-dt branch
  ARM: nomadik: set proper compatible for accelerometer
  ARM64: juno: add GPIO keys
  ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodes
  ARM: dts: Introduce STM32F429 MCU
  ARM: socfpga: dts: enable ethernet for Arria10 devkit
  ARM: dts: k2l: fix the netcp range size
  ARM: dts: k2e: fix the netcp range size
  ARM: dts: k2hk: fix the netcp range size
  ARM: dts: k2l-evm: Add device bindings for netcp driver
  ARM: dts: k2e-evm: Add device bindings for netcp driver
  ARM: dts: k2hk-evm: Add device bindings for netcp driver
  ARM: BCM5301X: Add DT for Asus RT-AC87U
  ARM: BCM5301X: add IRQ numbers for PCIe controller
  ARM: BCM5301X: add NAND flash chip description
  arm64: dts: Add dts files for Hisilicon Hi6220 SoC
  clk: hi6220: Document devicetree bindings for hi6220 clock
  arm64: hi6220: Document devicetree bindings for Hisilicon hi6220 SoC
  ARM: at91/dt: sama5d4ek: mci0 uses slot 0
  ARM: at91/dt: kizbox: fix mismatch LED PWM device
  ...

1 files changed, 76 insertions, 79 deletions

diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts
index 03deb84268ce..ad84fe4276c9 100644
--- a/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts
@@ -17,11 +17,6 @@
  *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  *     GNU General Public License for more details.
  *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
  * Or, alternatively,
  *
  *  b) Permission is hereby granted, free of charge, to any person
@@ -61,76 +56,8 @@
 		serial0 = &uart1;
 	};
 
-	soc@01c00000 {
-		mmc0: mmc@01c0f000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxinom>;
-			vmmc-supply = <&reg_vcc3v3>;
-			bus-width = <4>;
-			cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
-			cd-inverted;
-			status = "okay";
-		};
-
-		usbphy: phy@01c13400 {
-			usb1_vbus-supply = <&reg_usb1_vbus>;
-			status = "okay";
-		};
-
-		ehci0: usb@01c14000 {
-			status = "okay";
-		};
-
-		ohci0: usb@01c14400 {
-			status = "okay";
-		};
-
-		pinctrl@01c20800 {
-			mmc0_cd_pin_olinuxinom: mmc0_cd_pin@0 {
-				allwinner,pins = "PG0";
-				allwinner,function = "gpio_in";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-			};
-
-			led_pins_olinuxinom: led_pins@0 {
-				allwinner,pins = "PG9";
-				allwinner,function = "gpio_out";
-				allwinner,drive = <SUN4I_PINCTRL_20_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			usb1_vbus_pin_olinuxinom: usb1_vbus_pin@0 {
-				allwinner,pins = "PG11";
-				allwinner,function = "gpio_out";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-		};
-
-		uart1: serial@01c28400 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart1_pins_b>;
-			status = "okay";
-		};
-
-		i2c0: i2c@01c2ac00 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c0_pins_a>;
-			status = "okay";
-		};
-
-		i2c1: i2c@01c2b000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c1_pins_a>;
-			status = "okay";
-		};
-
-		i2c2: i2c@01c2b400 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c2_pins_a>;
-			status = "okay";
-		};
+	chosen {
+		stdout-path = "serial0:115200n8";
 	};
 
 	leds {
@@ -144,10 +71,80 @@
 			default-state = "on";
 		};
 	};
+};
+
+&ehci0 {
+	status = "okay";
+};
 
-	reg_usb1_vbus: usb1-vbus {
-		pinctrl-0 = <&usb1_vbus_pin_olinuxinom>;
-		gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
-		status = "okay";
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxinom>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
+	cd-inverted;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pio {
+	mmc0_cd_pin_olinuxinom: mmc0_cd_pin@0 {
+		allwinner,pins = "PG0";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 	};
+
+	led_pins_olinuxinom: led_pins@0 {
+		allwinner,pins = "PG9";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	usb1_vbus_pin_olinuxinom: usb1_vbus_pin@0 {
+		allwinner,pins = "PG11";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+};
+
+&reg_usb1_vbus {
+	pinctrl-0 = <&usb1_vbus_pin_olinuxinom>;
+	gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins_b>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
 };