Merge tag 'xceiv-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

usb: xceiv: patches for v3.7 merge window

nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.

Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.

We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.

Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.

2 files changed, 57 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
new file mode 100644
index 000000000000..36b9aede3f40
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
@@ -0,0 +1,40 @@
+USB COMPARATOR OF TWL CHIPS
+
+TWL6030 USB COMPARATOR
+ - compatible : Should be "ti,twl6030-usb"
+ - interrupts : Two interrupt numbers to the cpu should be specified. First
+   interrupt number is the otg interrupt number that raises ID interrupts when
+   the controller has to act as host and the second interrupt number is the
+   usb interrupt number that raises VBUS interrupts when the controller has to
+   act as device
+ - usb-supply : phandle to the regulator device tree node. It should be vusb
+   if it is twl6030 or ldousb if it is twl6025 subclass.
+
+twl6030-usb {
+	compatible = "ti,twl6030-usb";
+	interrupts = < 4 10 >;
+};
+
+Board specific device node entry
+&twl6030-usb {
+	usb-supply = <&vusb>;
+};
+
+TWL4030 USB PHY AND COMPARATOR
+ - compatible : Should be "ti,twl4030-usb"
+ - interrupts : The interrupt numbers to the cpu should be specified. First
+   interrupt number is the otg interrupt number that raises ID interrupts
+   and VBUS interrupts. The second interrupt number is optional.
+ - <supply-name>-supply : phandle to the regulator device tree node.
+   <supply-name> should be vusb1v5, vusb1v8 and vusb3v1
+ - usb_mode : The mode used by the phy to connect to the controller. "1"
+   specifies "ULPI" mode and "2" specifies "CEA2011_3PIN" mode.
+
+twl4030-usb {
+	compatible = "ti,twl4030-usb";
+	interrupts = < 10 4 >;
+	usb1v5-supply = <&vusb1v5>;
+	usb1v8-supply = <&vusb1v8>;
+	usb3v1-supply = <&vusb3v1>;
+	usb_mode = <1>;
+};
diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt
new file mode 100644
index 000000000000..80d4148cb661
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/usb-phy.txt
@@ -0,0 +1,17 @@
+USB PHY
+
+OMAP USB2 PHY
+
+Required properties:
+ - compatible: Should be "ti,omap-usb2"
+ - reg : Address and length of the register set for the device. Also
+add the address of control module dev conf register until a driver for
+control module is added
+
+This is usually a subnode of ocp2scp to which it is connected.
+
+usb2phy@4a0ad080 {
+	compatible = "ti,omap-usb2";
+	reg = <0x4a0ad080 0x58>,
+	      <0x4a002300 0x4>;
+};