Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (53 commits)
  spi/omap2_mcspi: Verify TX reg is empty after TX only xfer with DMA
  spi/omap2_mcspi: disable channel after TX_ONLY transfer in PIO mode
  spi/bfin_spi: namespace local structs
  spi/bfin_spi: init early
  spi/bfin_spi: check per-transfer bits_per_word
  spi/bfin_spi: warn when CS is driven by hardware (CPHA=0)
  spi/bfin_spi: cs should be always low when a new transfer begins
  spi/bfin_spi: fix typo in comment
  spi/bfin_spi: reject unsupported SPI modes
  spi/bfin_spi: use dma_disable_irq_nosync() in irq handler
  spi/bfin_spi: combine duplicate SPI_CTL read/write logic
  spi/bfin_spi: reset ctl_reg bits when setup is run again on a device
  spi/bfin_spi: push all size checks into the transfer function
  spi/bfin_spi: use nosync when disabling the IRQ from the IRQ handler
  spi/bfin_spi: sync hardware state before reprogramming everything
  spi/bfin_spi: save/restore state when suspending/resuming
  spi/bfin_spi: redo GPIO CS handling
  Blackfin: SPI: expand SPI bitmasks
  spi/bfin_spi: use the SPI namespaced bit names
  spi/bfin_spi: drop extra memory we don't need
  ...

1 files changed, 23 insertions, 1 deletions

diff --git a/Documentation/powerpc/dts-bindings/fsl/spi.txt b/Documentation/powerpc/dts-bindings/fsl/spi.txt
index 80510c018eea..777abd7399d5 100644
--- a/Documentation/powerpc/dts-bindings/fsl/spi.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/spi.txt
@@ -1,7 +1,9 @@
 * SPI (Serial Peripheral Interface)
 
 Required properties:
-- cell-index : SPI controller index.
+- cell-index : QE SPI subblock index.
+		0: QE subblock SPI1
+		1: QE subblock SPI2
 - compatible : should be "fsl,spi".
 - mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
 - reg : Offset and length of the register set for the device
@@ -29,3 +31,23 @@ Example:
 		gpios = <&gpio 18 1	// device reg=<0>
 			 &gpio 19 1>;	// device reg=<1>
 	};
+
+
+* eSPI (Enhanced Serial Peripheral Interface)
+
+Required properties:
+- compatible : should be "fsl,mpc8536-espi".
+- reg : Offset and length of the register set for the device.
+- interrupts : should contain eSPI interrupt, the device has one interrupt.
+- fsl,espi-num-chipselects : the number of the chipselect signals.
+
+Example:
+	spi@110000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc8536-espi";
+		reg = <0x110000 0x1000>;
+		interrupts = <53 0x2>;
+		interrupt-parent = <&mpic>;
+		fsl,espi-num-chipselects = <4>;
+	};