Merge tag 'imx-soc-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc2

From Shawn Guo:
The imx soc changes for 3.10:

* Enable anatop, well bisa and RBC for suspend to optimize the power
  consumption a little bit
* Clock changes for TVE, LDB, PATA, SRTC support
* Add System Reset Controller (SRC) support for imx5 and imx6
* Add initial imx6dl support based on imx6q code
* Kconfig for cpufreq-cpu0, defconfig updates and few other changes

* tag 'imx-soc-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6: (275 commits)
  ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
  ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
  ARM i.MX53: make tve_ext_sel propagate rate change to PLL
  ARM i.MX53: Remove unused tve_gate clkdev entry
  ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
  ARM: i.MX5: Add PATA and SRTC clocks
  ARM: imx: do not bring up unavailable cores
  ARM: imx: add initial imx6dl support
  ARM: imx1: mm: add call to mxc_device_init
  ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
  ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
  ARM: i.MX53 Add the cko1, cko2 clock outputs.
  staging: drm/imx: Use SRC to reset IPU
  ARM i.MX6q: Add GPU, VPU, IPU, and OpenVG resets to System Reset Controller (SRC)
  ARM: imx: do not use regmap_read for ANADIG_DIGPROG
  ARM i.MX6q: set the LDB serial clock parent to the video PLL
  ARM i.MX6q: Add audio/video PLL post dividers for i.MX6q rev 1.1
  ARM i.MX6q: fix ldb di divider and selector clocks
  ARM i.MX53: fix ldb di divider and selector clocks
  ARM i.MX: Add imx_clk_divider_flags and imx_clk_mux_flags
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>

Trivial change/change conflict in arch/arm/mach-imx/mach-imx6q.c resolved.

6 files changed, 145 insertions, 4 deletions

diff --git a/Documentation/devicetree/bindings/clock/imx5-clock.txt b/Documentation/devicetree/bindings/clock/imx5-clock.txt
index 2a0c904c46ae..d71b4b2c077d 100644
--- a/Documentation/devicetree/bindings/clock/imx5-clock.txt
+++ b/Documentation/devicetree/bindings/clock/imx5-clock.txt
@@ -38,7 +38,6 @@ clocks and IDs.
 	usb_phy_podf		23
 	cpu_podf		24
 	di_pred			25
-	tve_di			26
 	tve_s			27
 	uart1_ipg_gate		28
 	uart1_per_gate		29
@@ -172,6 +171,19 @@ clocks and IDs.
 	can1_serial_gate	157
 	can1_ipg_gate		158
 	owire_gate		159
+	gpu3d_s			160
+	gpu2d_s			161
+	gpu3d_gate		162
+	gpu2d_gate		163
+	garb_gate		164
+	cko1_sel		165
+	cko1_podf		166
+	cko1			167
+	cko2_sel		168
+	cko2_podf		169
+	cko2			170
+	srtc_gate		171
+	pata_gate		172
 
 Examples (for mx53):
 
diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt
index 969b38e06ad3..6deb6fd1c7cd 100644
--- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt
+++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt
@@ -205,6 +205,9 @@ clocks and IDs.
 	enet_ref		190
 	usbphy1_gate		191
 	usbphy2_gate		192
+	pll4_post_div		193
+	pll5_post_div		194
+	pll5_video_div		195
 
 Examples:
 
diff --git a/Documentation/devicetree/bindings/reset/fsl,imx-src.txt b/Documentation/devicetree/bindings/reset/fsl,imx-src.txt
new file mode 100644
index 000000000000..13301777e11c
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/fsl,imx-src.txt
@@ -0,0 +1,49 @@
+Freescale i.MX System Reset Controller
+======================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "fsl,<chip>-src"
+- reg: should be register base and length as documented in the
+  datasheet
+- interrupts: Should contain SRC interrupt and CPU WDOG interrupt,
+  in this order.
+- #reset-cells: 1, see below
+
+example:
+
+src: src@020d8000 {
+        compatible = "fsl,imx6q-src";
+        reg = <0x020d8000 0x4000>;
+        interrupts = <0 91 0x04 0 96 0x04>;
+        #reset-cells = <1>;
+};
+
+Specifying reset lines connected to IP modules
+==============================================
+
+The system reset controller can be used to reset the GPU, VPU,
+IPU, and OpenVG IP modules on i.MX5 and i.MX6 ICs. Those device
+nodes should specify the reset line on the SRC in their resets
+property, containing a phandle to the SRC device node and a
+RESET_INDEX specifying which module to reset, as described in
+reset.txt
+
+example:
+
+        ipu1: ipu@02400000 {
+                resets = <&src 2>;
+        };
+        ipu2: ipu@02800000 {
+                resets = <&src 4>;
+        };
+
+The following RESET_INDEX values are valid for i.MX5:
+GPU_RESET     0
+VPU_RESET     1
+IPU1_RESET    2
+OPEN_VG_RESET 3
+The following additional RESET_INDEX value is valid for i.MX6:
+IPU2_RESET    4
diff --git a/Documentation/devicetree/bindings/reset/reset.txt b/Documentation/devicetree/bindings/reset/reset.txt
new file mode 100644
index 000000000000..31db6ff84908
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/reset.txt
@@ -0,0 +1,75 @@
+= Reset Signal Device Tree Bindings =
+
+This binding is intended to represent the hardware reset signals present
+internally in most IC (SoC, FPGA, ...) designs. Reset signals for whole
+standalone chips are most likely better represented as GPIOs, although there
+are likely to be exceptions to this rule.
+
+Hardware blocks typically receive a reset signal. This signal is generated by
+a reset provider (e.g. power management or clock module) and received by a
+reset consumer (the module being reset, or a module managing when a sub-
+ordinate module is reset). This binding exists to represent the provider and
+consumer, and provide a way to couple the two together.
+
+A reset signal is represented by the phandle of the provider, plus a reset
+specifier - a list of DT cells that represents the reset signal within the
+provider. The length (number of cells) and semantics of the reset specifier
+are dictated by the binding of the reset provider, although common schemes
+are described below.
+
+A word on where to place reset signal consumers in device tree: It is possible
+in hardware for a reset signal to affect multiple logically separate HW blocks
+at once. In this case, it would be unwise to represent this reset signal in
+the DT node of each affected HW block, since if activated, an unrelated block
+may be reset. Instead, reset signals should be represented in the DT node
+where it makes most sense to control it; this may be a bus node if all
+children of the bus are affected by the reset signal, or an individual HW
+block node for dedicated reset signals. The intent of this binding is to give
+appropriate software access to the reset signals in order to manage the HW,
+rather than to slavishly enumerate the reset signal that affects each HW
+block.
+
+= Reset providers =
+
+Required properties:
+#reset-cells:	Number of cells in a reset specifier; Typically 0 for nodes
+		with a single reset output and 1 for nodes with multiple
+		reset outputs.
+
+For example:
+
+	rst: reset-controller {
+		#reset-cells = <1>;
+	};
+
+= Reset consumers =
+
+Required properties:
+resets:		List of phandle and reset specifier pairs, one pair
+		for each reset signal that affects the device, or that the
+		device manages. Note: if the reset provider specifies '0' for
+		#reset-cells, then only the phandle portion of the pair will
+		appear.
+
+Optional properties:
+reset-names:	List of reset signal name strings sorted in the same order as
+		the resets property. Consumers drivers will use reset-names to
+		match reset signal names with reset specifiers.
+
+For example:
+
+	device {
+		resets = <&rst 20>;
+		reset-names = "reset";
+	};
+
+This represents a device with a single reset signal named "reset".
+
+	bus {
+		resets = <&rst 10> <&rst 11> <&rst 12> <&rst 11>;
+		reset-names = "i2s1", "i2s2", "dma", "mixer";
+	};
+
+This represents a bus that controls the reset signal of each of four sub-
+ordinate devices. Consider for example a bus that fails to operate unless no
+child device has reset asserted.
diff --git a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt
index 07654f0338b6..f7698573cb9c 100644
--- a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt
+++ b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt
@@ -8,6 +8,8 @@ Required properties:
 - interrupts: Should contain sync interrupt and error interrupt,
   in this order.
 - #crtc-cells: 1, See below
+- resets: phandle pointing to the system reset controller and
+          reset line index, see reset/fsl,imx-src.txt for details
 
 example:
 
@@ -16,6 +18,7 @@ ipu: ipu@18000000 {
 	compatible = "fsl,imx53-ipu";
 	reg = <0x18000000 0x080000000>;
 	interrupts = <11 10>;
+	resets = <&src 2>;
 };
 
 Parallel display support
diff --git a/Documentation/sound/alsa/ALSA-Configuration.txt b/Documentation/sound/alsa/ALSA-Configuration.txt
index 4499bd948860..95731a08f257 100644
--- a/Documentation/sound/alsa/ALSA-Configuration.txt
+++ b/Documentation/sound/alsa/ALSA-Configuration.txt
@@ -890,9 +890,8 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
     enable_msi	- Enable Message Signaled Interrupt (MSI) (default = off)
     power_save	- Automatic power-saving timeout (in second, 0 =
 		disable)
-    power_save_controller - Support runtime D3 of HD-audio controller
-		(-1 = on for supported chip (default), false = off,
-		 true = force to on even for unsupported hardware)
+    power_save_controller - Reset HD-audio controller in power-saving mode
+		(default = on)
     align_buffer_size - Force rounding of buffer/period sizes to multiples
     		      of 128 bytes. This is more efficient in terms of memory
 		      access but isn't required by the HDA spec and prevents