Merge commit 'v2.6.30' into for-2.6.31

1 files changed, 12 insertions, 77 deletions

diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index 0ab0230cbcb0..d16b7a1c3793 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -43,12 +43,11 @@ Table of Contents
     2) Representing devices without a current OF specification
       a) PHY nodes
       b) Interrupt controllers
-      c) CFI or JEDEC memory-mapped NOR flash
-      d) 4xx/Axon EMAC ethernet nodes
-      e) Xilinx IP cores
-      f) USB EHCI controllers
-      g) MDIO on GPIOs
-      h) SPI busses
+      c) 4xx/Axon EMAC ethernet nodes
+      d) Xilinx IP cores
+      e) USB EHCI controllers
+      f) MDIO on GPIOs
+      g) SPI busses
 
   VII - Marvell Discovery mv64[345]6x System Controller chips
     1) The /system-controller node
@@ -999,7 +998,7 @@ compatibility.
       translation of SOC addresses for memory mapped SOC registers.
     - bus-frequency: Contains the bus frequency for the SOC node.
       Typically, the value of this field is filled in by the boot
-      loader. 
+      loader.
 
 
   Recommended properties:
@@ -1287,71 +1286,7 @@ platforms are moved over to use the flattened-device-tree model.
 		device_type = "open-pic";
 	};
 
-   c) CFI or JEDEC memory-mapped NOR flash
-
-    Flash chips (Memory Technology Devices) are often used for solid state
-    file systems on embedded devices.
-
-     - compatible : should contain the specific model of flash chip(s)
-       used, if known, followed by either "cfi-flash" or "jedec-flash"
-     - reg : Address range of the flash chip
-     - bank-width : Width (in bytes) of the flash bank.  Equal to the
-       device width times the number of interleaved chips.
-     - device-width : (optional) Width of a single flash chip.  If
-       omitted, assumed to be equal to 'bank-width'.
-     - #address-cells, #size-cells : Must be present if the flash has
-       sub-nodes representing partitions (see below).  In this case
-       both #address-cells and #size-cells must be equal to 1.
-
-    For JEDEC compatible devices, the following additional properties
-    are defined:
-
-     - vendor-id : Contains the flash chip's vendor id (1 byte).
-     - device-id : Contains the flash chip's device id (1 byte).
-
-    In addition to the information on the flash bank itself, the
-    device tree may optionally contain additional information
-    describing partitions of the flash address space.  This can be
-    used on platforms which have strong conventions about which
-    portions of the flash are used for what purposes, but which don't
-    use an on-flash partition table such as RedBoot.
-
-    Each partition is represented as a sub-node of the flash device.
-    Each node's name represents the name of the corresponding
-    partition of the flash device.
-
-    Flash partitions
-     - reg : The partition's offset and size within the flash bank.
-     - label : (optional) The label / name for this flash partition.
-       If omitted, the label is taken from the node name (excluding
-       the unit address).
-     - read-only : (optional) This parameter, if present, is a hint to
-       Linux that this flash partition should only be mounted
-       read-only.  This is usually used for flash partitions
-       containing early-boot firmware images or data which should not
-       be clobbered.
-
-    Example:
-
-	flash@ff000000 {
-		compatible = "amd,am29lv128ml", "cfi-flash";
-		reg = <ff000000 01000000>;
-		bank-width = <4>;
-		device-width = <1>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		fs@0 {
-			label = "fs";
-			reg = <0 f80000>;
-		};
-		firmware@f80000 {
-			label ="firmware";
-			reg = <f80000 80000>;
-			read-only;
-		};
-	};
-
-    d) 4xx/Axon EMAC ethernet nodes
+    c) 4xx/Axon EMAC ethernet nodes
 
     The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
     the Axon bridge.  To operate this needs to interact with a ths
@@ -1499,7 +1434,7 @@ platforms are moved over to use the flattened-device-tree model.
 			   available.
 			   For Axon: 0x0000012a
 
-   e) Xilinx IP cores
+   d) Xilinx IP cores
 
    The Xilinx EDK toolchain ships with a set of IP cores (devices) for use
    in Xilinx Spartan and Virtex FPGAs.  The devices cover the whole range
@@ -1761,7 +1696,7 @@ platforms are moved over to use the flattened-device-tree model.
       listed above, nodes for these devices should include a phy-handle
       property, and may include other common network device properties
       like local-mac-address.
-      
+
       iv) Xilinx Uartlite
 
       Xilinx uartlite devices are simple fixed speed serial ports.
@@ -1793,7 +1728,7 @@ platforms are moved over to use the flattened-device-tree model.
        - reg-offset : A value of 3 is required
        - reg-shift : A value of 2 is required
 
-    f) USB EHCI controllers
+    e) USB EHCI controllers
 
     Required properties:
       - compatible : should be "usb-ehci".
@@ -1819,7 +1754,7 @@ platforms are moved over to use the flattened-device-tree model.
 		   big-endian;
 	   };
 
-   g) MDIO on GPIOs
+   f) MDIO on GPIOs
 
    Currently defined compatibles:
    - virtual,gpio-mdio
@@ -1839,7 +1774,7 @@ platforms are moved over to use the flattened-device-tree model.
 			 &qe_pio_c 6>;
 	};
 
-    h) SPI (Serial Peripheral Interface) busses
+    g) SPI (Serial Peripheral Interface) busses
 
     SPI busses can be described with a node for the SPI master device
     and a set of child nodes for each SPI slave on the bus.  For this