Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6

Conflicts:

	Documentation/kernel-parameters.txt
	arch/sh/include/asm/elf.h

1 files changed, 71 insertions, 7 deletions

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index abeff96e9d46..bcecfaa1e770 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -284,6 +284,11 @@ and is between 256 and 4096 characters. It is defined in the file
 			isolate - enable device isolation (each device, as far
 			          as possible, will get its own protection
 			          domain)
+			fullflush - enable flushing of IO/TLB entries when
+				    they are unmapped. Otherwise they are
+				    flushed before they will be reused, which
+				    is a lot of faster
+
 	amd_iommu_size= [HW,X86-64]
 			Define the size of the aperture for the AMD IOMMU
 			driver. Possible values are:
@@ -463,12 +468,6 @@ and is between 256 and 4096 characters. It is defined in the file
 			Range: 0 - 8192
 			Default: 64
 
-	disable_8254_timer
-	enable_8254_timer
-			[IA32/X86_64] Disable/Enable interrupt 0 timer routing
-			over the 8254 in addition to over the IO-APIC. The
-			kernel tries to set a sensible default.
-
 	hpet=		[X86-32,HPET] option to control HPET usage
 			Format: { enable (default) | disable | force }
 			disable: disable HPET and use PIT instead
@@ -659,11 +658,12 @@ and is between 256 and 4096 characters. It is defined in the file
 	earlyprintk=	[X86-32,X86-64,SH,BLACKFIN]
 			earlyprintk=vga
 			earlyprintk=serial[,ttySn[,baudrate]]
+			earlyprintk=dbgp
 
 			Append ",keep" to not disable it when the real console
 			takes over.
 
-			Only vga or serial at a time, not both.
+			Only vga or serial or usb debug port at a time.
 
 			Currently only ttyS0 and ttyS1 are supported.
 
@@ -798,6 +798,7 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	hlt		[BUGS=ARM,SH]
 
+	i8042.debug	[HW] Toggle i8042 debug mode
 	i8042.direct	[HW] Put keyboard port into non-translated mode
 	i8042.dumbkbd	[HW] Pretend that controller can only read data from
 			     keyboard and cannot control its state
@@ -1022,6 +1023,10 @@ and is between 256 and 4096 characters. It is defined in the file
 			(only serial suported for now)
 			Format: <serial_device>[,baud]
 
+	kmac=		[MIPS] korina ethernet MAC address.
+			Configure the RouterBoard 532 series on-chip
+			Ethernet adapter MAC address.
+
 	l2cr=		[PPC]
 
 	l3cr=		[PPC]
@@ -1234,6 +1239,29 @@ and is between 256 and 4096 characters. It is defined in the file
 			         or
 			         memmap=0x10000$0x18690000
 
+	memory_corruption_check=0/1 [X86]
+			Some BIOSes seem to corrupt the first 64k of
+			memory when doing things like suspend/resume.
+			Setting this option will scan the memory
+			looking for corruption.  Enabling this will
+			both detect corruption and prevent the kernel
+			from using the memory being corrupted.
+			However, its intended as a diagnostic tool; if
+			repeatable BIOS-originated corruption always
+			affects the same memory, you can use memmap=
+			to prevent the kernel from using that memory.
+
+	memory_corruption_check_size=size [X86]
+			By default it checks for corruption in the low
+			64k, making this memory unavailable for normal
+			use.  Use this parameter to scan for
+			corruption in more or less memory.
+
+	memory_corruption_check_period=seconds [X86]
+			By default it checks for corruption every 60
+			seconds.  Use this parameter to check at some
+			other rate.  0 disables periodic checking.
+
 	memtest=	[KNL,X86] Enable memtest
 			Format: <integer>
 			range: 0,4 : pattern number
@@ -1435,6 +1463,12 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	nolapic_timer	[X86-32,APIC] Do not use the local APIC timer.
 
+	nox2apic	[X86-64,APIC] Do not enable x2APIC mode.
+
+	x2apic_phys	[X86-64,APIC] Use x2apic physical mode instead of
+			default x2apic cluster mode on platforms
+			supporting x2apic.
+
 	noltlbs		[PPC] Do not use large page/tlb entries for kernel
 			lowmem mapping on PPC40x.
 
@@ -1690,6 +1724,11 @@ and is between 256 and 4096 characters. It is defined in the file
 			autoconfiguration.
 			Ranges are in pairs (memory base and size).
 
+	dynamic_printk
+			Enables pr_debug()/dev_dbg() calls if
+			CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. These can also
+			be switched on/off via <debugfs>/dynamic_printk/modules
+
 	print-fatal-signals=
 			[KNL] debug: print fatal signals
 			print-fatal-signals=1: print segfault info to
@@ -1892,6 +1931,12 @@ and is between 256 and 4096 characters. It is defined in the file
 	shapers=	[NET]
 			Maximal number of shapers.
 
+	show_msr=	[x86] show boot-time MSR settings
+			Format: { <integer> }
+			Show boot-time (BIOS-initialized) MSR settings.
+			The parameter means the number of CPUs to show,
+			for example 1 means boot CPU only.
+
 	sim710=		[SCSI,HW]
 			See header of drivers/scsi/sim710.c.
 
@@ -2218,6 +2263,25 @@ and is between 256 and 4096 characters. It is defined in the file
 			autosuspended.  Devices for which the delay is set
 			to a negative value won't be autosuspended at all.
 
+	usbcore.usbfs_snoop=
+			[USB] Set to log all usbfs traffic (default 0 = off).
+
+	usbcore.blinkenlights=
+			[USB] Set to cycle leds on hubs (default 0 = off).
+
+	usbcore.old_scheme_first=
+			[USB] Start with the old device initialization
+			scheme (default 0 = off).
+
+	usbcore.use_both_schemes=
+			[USB] Try the other device initialization scheme
+			if the first one fails (default 1 = enabled).
+
+	usbcore.initial_descriptor_timeout=
+			[USB] Specifies timeout for the initial 64-byte
+                        USB_REQ_GET_DESCRIPTOR request in milliseconds
+			(default 5000 = 5.0 seconds).
+
 	usbhid.mousepoll=
 			[USBHID] The interval which mice are to be polled at.