Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Conflicts:
	net/ipv4/arp.c

The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.

Signed-off-by: David S. Miller <davem@davemloft.net>

13 files changed, 174 insertions, 25 deletions

diff --git a/Documentation/devicetree/bindings/arm/gic-v3.txt b/Documentation/devicetree/bindings/arm/gic-v3.txt
index ddfade40ac59..7803e77d85cb 100644
--- a/Documentation/devicetree/bindings/arm/gic-v3.txt
+++ b/Documentation/devicetree/bindings/arm/gic-v3.txt
@@ -57,6 +57,8 @@ used to route Message Signalled Interrupts (MSI) to the CPUs.
 These nodes must have the following properties:
 - compatible : Should at least contain  "arm,gic-v3-its".
 - msi-controller : Boolean property. Identifies the node as an MSI controller
+- #msi-cells: Must be <1>. The single msi-cell is the DeviceID of the device
+  which will generate the MSI.
 - reg: Specifies the base physical address and size of the ITS
   registers.
 
@@ -83,6 +85,7 @@ Examples:
 		gic-its@2c200000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c200000 0 0x200000>;
 		};
 	};
@@ -107,12 +110,14 @@ Examples:
 		gic-its@2c200000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c200000 0 0x200000>;
 		};
 
 		gic-its@2c400000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c400000 0 0x200000>;
 		};
 	};
diff --git a/Documentation/devicetree/bindings/arm/idle-states.txt b/Documentation/devicetree/bindings/arm/idle-states.txt
index a8274eabae2e..b8e41c148a3c 100644
--- a/Documentation/devicetree/bindings/arm/idle-states.txt
+++ b/Documentation/devicetree/bindings/arm/idle-states.txt
@@ -497,7 +497,7 @@ cpus {
 	};
 
 	idle-states {
-		entry-method = "arm,psci";
+		entry-method = "psci";
 
 		CPU_RETENTION_0_0: cpu-retention-0-0 {
 			compatible = "arm,idle-state";
diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt
index 5788d5cf1252..82d40e2505f6 100644
--- a/Documentation/devicetree/bindings/gpio/gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio.txt
@@ -16,7 +16,9 @@ properties, each containing a 'gpio-list':
 GPIO properties should be named "[<name>-]gpios", with <name> being the purpose
 of this GPIO for the device. While a non-existent <name> is considered valid
 for compatibility reasons (resolving to the "gpios" property), it is not allowed
-for new bindings.
+for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old
+bindings use it, but are only supported for compatibility reasons and should not
+be used for newer bindings since it has been deprecated.
 
 GPIO properties can contain one or more GPIO phandles, but only in exceptional
 cases should they contain more than one. If your device uses several GPIOs with
diff --git a/Documentation/devicetree/bindings/iio/accel/bma180.txt b/Documentation/devicetree/bindings/iio/accel/bma180.txt
index c5933573e0f6..4a3679d54457 100644
--- a/Documentation/devicetree/bindings/iio/accel/bma180.txt
+++ b/Documentation/devicetree/bindings/iio/accel/bma180.txt
@@ -1,10 +1,11 @@
-* Bosch BMA180 triaxial acceleration sensor
+* Bosch BMA180 / BMA250 triaxial acceleration sensor
 
 http://omapworld.com/BMA180_111_1002839.pdf
+http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf
 
 Required properties:
 
-  - compatible : should be "bosch,bma180"
+  - compatible : should be "bosch,bma180" or "bosch,bma250"
   - reg : the I2C address of the sensor
 
 Optional properties:
@@ -13,6 +14,9 @@ Optional properties:
 
   - interrupts : interrupt mapping for GPIO IRQ, it should by configured with
 		flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING
+		For the bma250 the first interrupt listed must be the one
+		connected to the INT1 pin, the second (optional) interrupt
+		listed must be the one connected to the INT2 pin.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt
new file mode 100644
index 000000000000..9d9e930f3251
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt
@@ -0,0 +1,36 @@
+* Toradex Colibri VF50 Touchscreen driver
+
+Required Properties:
+- compatible must be toradex,vf50-touchscreen
+- io-channels: adc channels being used by the Colibri VF50 module
+- xp-gpios: FET gate driver for input of X+
+- xm-gpios: FET gate driver for input of X-
+- yp-gpios: FET gate driver for input of Y+
+- ym-gpios: FET gate driver for input of Y-
+- interrupt-parent: phandle for the interrupt controller
+- interrupts: pen irq interrupt for touch detection
+- pinctrl-names: "idle", "default", "gpios"
+- pinctrl-0: pinctrl node for pen/touch detection state pinmux
+- pinctrl-1: pinctrl node for X/Y and pressure measurement (ADC) state pinmux
+- pinctrl-2: pinctrl node for gpios functioning as FET gate drivers
+- vf50-ts-min-pressure: pressure level at which to stop measuring X/Y values
+
+Example:
+
+	touchctrl: vf50_touchctrl {
+		compatible = "toradex,vf50-touchscreen";
+		io-channels = <&adc1 0>,<&adc0 0>,
+				<&adc0 1>,<&adc1 2>;
+		xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+		xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+		yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "idle","default","gpios";
+		pinctrl-0 = <&pinctrl_touchctrl_idle>;
+		pinctrl-1 = <&pinctrl_touchctrl_default>;
+		pinctrl-2 = <&pinctrl_touchctrl_gpios>;
+		vf50-ts-min-pressure = <200>;
+		status = "disabled";
+	};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
new file mode 100644
index 000000000000..853dff96dd9f
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
@@ -0,0 +1,36 @@
+* Freescale i.MX6UL Touch Controller
+
+Required properties:
+- compatible: must be "fsl,imx6ul-tsc".
+- reg: this touch controller address and the ADC2 address.
+- interrupts: the interrupt of this touch controller and ADC2.
+- clocks: the root clock of touch controller and ADC2.
+- clock-names; must be "tsc" and "adc".
+- xnur-gpio: the X- gpio this controller connect to.
+  This xnur-gpio returns to low once the finger leave the touch screen (The
+  last touch event the touch controller capture).
+
+Optional properties:
+- measure-delay-time: the value of measure delay time.
+  Before X-axis or Y-axis measurement, the screen need some time before
+  even potential distribution ready.
+  This value depends on the touch screen.
+- pre-charge-time: the touch screen need some time to precharge.
+  This value depends on the touch screen.
+
+Example:
+	tsc: tsc@02040000 {
+		compatible = "fsl,imx6ul-tsc";
+		reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
+		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks IMX6UL_CLK_IPG>,
+			 <&clks IMX6UL_CLK_ADC2>;
+		clock-names = "tsc", "adc";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tsc>;
+		xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+		measure-delay-time = <0xfff>;
+		pre-charge-time = <0xffff>;
+		status = "okay";
+	};
diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt
index d8ef5bf50f11..7fab84b33531 100644
--- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt
+++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt
@@ -7,7 +7,8 @@ OHCI and EHCI controllers.
 
 Required properties:
 - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC;
-	      "renesas,pci-r8a7791" for the R8A7791 SoC.
+	      "renesas,pci-r8a7791" for the R8A7791 SoC;
+	      "renesas,pci-r8a7794" for the R8A7794 SoC.
 - reg:	A list of physical regions to access the device: the first is
 	the operational registers for the OHCI/EHCI controllers and the
 	second is for the bridge configuration and control registers.
diff --git a/Documentation/devicetree/bindings/regulator/pbias-regulator.txt b/Documentation/devicetree/bindings/regulator/pbias-regulator.txt
index 32aa26f1e434..acbcb452a69a 100644
--- a/Documentation/devicetree/bindings/regulator/pbias-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/pbias-regulator.txt
@@ -2,7 +2,12 @@ PBIAS internal regulator for SD card dual voltage i/o pads on OMAP SoCs.
 
 Required properties:
 - compatible:
-  - "ti,pbias-omap" for OMAP2, OMAP3, OMAP4, OMAP5, DRA7.
+  - should be "ti,pbias-dra7" for DRA7
+  - should be "ti,pbias-omap2" for OMAP2
+  - should be "ti,pbias-omap3" for OMAP3
+  - should be "ti,pbias-omap4" for OMAP4
+  - should be "ti,pbias-omap5" for OMAP5
+  - "ti,pbias-omap" is deprecated
 - reg: pbias register offset from syscon base and size of pbias register.
 - syscon : phandle of the system control module
 - regulator-name : should be
diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt
index dcefc438272f..6160ffbcb3d3 100644
--- a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt
+++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt
@@ -15,17 +15,18 @@ Required properties:
 - interrupts: Should contain spi interrupt
 
 - clocks: phandles to input clocks.
-  The first should be <&topckgen CLK_TOP_SPI_SEL>.
-  The second should be one of the following.
+  The first should be one of the following. It's PLL.
    -  <&clk26m>: specify parent clock 26MHZ.
    -  <&topckgen CLK_TOP_SYSPLL3_D2>: specify parent clock 109MHZ.
 				      It's the default one.
    -  <&topckgen CLK_TOP_SYSPLL4_D2>: specify parent clock 78MHZ.
    -  <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ.
    -  <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ.
+  The second should be <&topckgen CLK_TOP_SPI_SEL>. It's clock mux.
+  The third is <&pericfg CLK_PERI_SPI0>. It's clock gate.
 
-- clock-names: shall be "spi-clk" for the controller clock, and
-  "parent-clk" for the parent clock.
+- clock-names: shall be "parent-clk" for the parent clock, "sel-clk" for the
+  muxes clock, and "spi-clk" for the clock gate.
 
 Optional properties:
 - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi
@@ -44,8 +45,11 @@ spi: spi@1100a000 {
 	#size-cells = <0>;
 	reg = <0 0x1100a000 0 0x1000>;
 	interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>;
-	clocks = <&topckgen CLK_TOP_SPI_SEL>, <&topckgen CLK_TOP_SYSPLL3_D2>;
-	clock-names = "spi-clk", "parent-clk";
+	clocks = <&topckgen CLK_TOP_SYSPLL3_D2>,
+		 <&topckgen CLK_TOP_SPI_SEL>,
+		 <&pericfg CLK_PERI_SPI0>;
+	clock-names = "parent-clk", "sel-clk", "spi-clk";
+
 	mediatek,pad-select = <0>;
 	status = "disabled";
 };
diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt
index 8a49362dea6e..41b817f7b670 100644
--- a/Documentation/devicetree/bindings/thermal/thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/thermal.txt
@@ -55,19 +55,11 @@ of heat dissipation). For example a fan's cooling states correspond to
 the different fan speeds possible. Cooling states are referred to by
 single unsigned integers, where larger numbers mean greater heat
 dissipation. The precise set of cooling states associated with a device
-(as referred to be the cooling-min-state and cooling-max-state
+(as referred to by the cooling-min-level and cooling-max-level
 properties) should be defined in a particular device's binding.
 For more examples of cooling devices, refer to the example sections below.
 
 Required properties:
-- cooling-min-state:	An integer indicating the smallest
-  Type: unsigned	cooling state accepted. Typically 0.
-  Size: one cell
-
-- cooling-max-state:	An integer indicating the largest
-  Type: unsigned	cooling state accepted.
-  Size: one cell
-
 - #cooling-cells:	Used to provide cooling device specific information
   Type: unsigned	while referring to it. Must be at least 2, in order
   Size: one cell      	to specify minimum and maximum cooling state used
@@ -77,6 +69,15 @@ Required properties:
 			See Cooling device maps section below for more details
 			on how consumers refer to cooling devices.
 
+Optional properties:
+- cooling-min-level:	An integer indicating the smallest
+  Type: unsigned	cooling state accepted. Typically 0.
+  Size: one cell
+
+- cooling-max-level:	An integer indicating the largest
+  Type: unsigned	cooling state accepted.
+  Size: one cell
+
 * Trip points
 
 The trip node is a node to describe a point in the temperature domain
@@ -225,8 +226,8 @@ cpus {
 			396000  950000
 			198000  850000
 		>;
-		cooling-min-state = <0>;
-		cooling-max-state = <3>;
+		cooling-min-level = <0>;
+		cooling-max-level = <3>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 	...
@@ -240,8 +241,8 @@ cpus {
 	 */
 	fan0: fan@0x48 {
 		...
-		cooling-min-state = <0>;
-		cooling-max-state = <9>;
+		cooling-min-level = <0>;
+		cooling-max-level = <9>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 };
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index ac5f0c34ae00..82d2ac97af74 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -203,6 +203,7 @@ sitronix	Sitronix Technology Corporation
 skyworks	Skyworks Solutions, Inc.
 smsc	Standard Microsystems Corporation
 snps	Synopsys, Inc.
+socionext	Socionext Inc.
 solidrun	SolidRun
 solomon        Solomon Systech Limited
 sony	Sony Corporation
diff --git a/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt
new file mode 100644
index 000000000000..f7cc7c060910
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt
@@ -0,0 +1,35 @@
+* Atmel SAMA5D4 Watchdog Timer (WDT) Controller
+
+Required properties:
+- compatible: "atmel,sama5d4-wdt"
+- reg: base physical address and length of memory mapped region.
+
+Optional properties:
+- timeout-sec: watchdog timeout value (in seconds).
+- interrupts: interrupt number to the CPU.
+- atmel,watchdog-type: should be "hardware" or "software".
+	"hardware": enable watchdog fault reset. A watchdog fault triggers
+		    watchdog reset.
+	"software": enable watchdog fault interrupt. A watchdog fault asserts
+		    watchdog interrupt.
+- atmel,idle-halt: present if you want to stop the watchdog when the CPU is
+		   in idle state.
+	CAUTION: This property should be used with care, it actually makes the
+	watchdog not counting when the CPU is in idle state, therefore the
+	watchdog reset time depends on mean CPU usage and will not reset at all
+	if the CPU stop working while it is in idle state, which is probably
+	not what you want.
+- atmel,dbg-halt: present if you want to stop the watchdog when the CPU is
+		  in debug state.
+
+Example:
+	watchdog@fc068640 {
+		compatible = "atmel,sama5d4-wdt";
+		reg = <0xfc068640 0x10>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH 5>;
+		timeout-sec = <10>;
+		atmel,watchdog-type = "hardware";
+		atmel,dbg-halt;
+		atmel,idle-halt;
+		status = "okay";
+	};
diff --git a/Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt b/Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt
new file mode 100644
index 000000000000..09f6b24969e0
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt
@@ -0,0 +1,19 @@
+* NXP LPC18xx Watchdog Timer (WDT)
+
+Required properties:
+- compatible: Should be "nxp,lpc1850-wwdt"
+- reg: Should contain WDT registers location and length
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Should contain "wdtclk" and "reg"; the watchdog counter
+               clock and register interface clock respectively.
+- interrupts: Should contain WDT interrupt
+
+Examples:
+
+watchdog@40080000 {
+	compatible = "nxp,lpc1850-wwdt";
+	reg = <0x40080000 0x24>;
+	clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_WWDT>;
+	clock-names = "wdtclk", "reg";
+	interrupts = <49>;
+};