i2c: mux: Add dt support to i2c-mux-gpio driver

Allow the i2c-mux-gpio to be used by a device tree enabled device. The
bindings are inspired by the one found in the i2c-mux-pinctrl driver.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>

[wsa: fixed some whitespace]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

1 files changed, 81 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt
new file mode 100644
index 000000000000..66709a825541
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt
@@ -0,0 +1,81 @@
+GPIO-based I2C Bus Mux
+
+This binding describes an I2C bus multiplexer that uses GPIOs to
+route the I2C signals.
+
+                                  +-----+  +-----+
+                                  | dev |  | dev |
+    +------------+                +-----+  +-----+
+    | SoC        |                   |        |
+    |            |          /--------+--------+
+    |   +------+ |  +------+    child bus A, on GPIO value set to 0
+    |   | I2C  |-|--| Mux  |
+    |   +------+ |  +--+---+    child bus B, on GPIO value set to 1
+    |            |     |    \----------+--------+--------+
+    |   +------+ |     |               |        |        |
+    |   | GPIO |-|-----+            +-----+  +-----+  +-----+
+    |   +------+ |                  | dev |  | dev |  | dev |
+    +------------+                  +-----+  +-----+  +-----+
+
+Required properties:
+- compatible: i2c-mux-gpio
+- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
+  port is connected to.
+- mux-gpios: list of gpios used to control the muxer
+* Standard I2C mux properties. See mux.txt in this directory.
+* I2C child bus nodes. See mux.txt in this directory.
+
+Optional properties:
+- idle-state: value to set the muxer to when idle. When no value is
+  given, it defaults to the last value used.
+
+For each i2c child node, an I2C child bus will be created. They will
+be numbered based on their order in the device tree.
+
+Whenever an access is made to a device on a child bus, the value set
+in the revelant node's reg property will be output using the list of
+GPIOs, the first in the list holding the least-significant value.
+
+If an idle state is defined, using the idle-state (optional) property,
+whenever an access is not being made to a device on a child bus, the
+GPIOs will be set according to the idle value.
+
+If an idle state is not defined, the most recently used value will be
+left programmed into hardware whenever no access is being made to a
+device on a child bus.
+
+Example:
+	i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+		i2c-parent = <&i2c1>;
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ssd1307: oled@3c {
+				compatible = "solomon,ssd1307fb-i2c";
+				reg = <0x3c>;
+				pwms = <&pwm 4 3000>;
+				reset-gpios = <&gpio2 7 1>;
+				reset-active-low;
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pca9555: pca9555@20 {
+				compatible = "nxp,pca9555";
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x20>;
+			};
+		};
+	};