Merge tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB patches from Greg KH:
 "Here's the big USB driver pull request for 3.12-rc1

  Lots of USB driver fixes and updates.  Nothing major, just the normal
  xhci, gadget, and other driver changes.  Full details in the shortlog"

* tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (352 commits)
  usbcore: fix incorrect type in assignment in descriptors_changed()
  usbcore: compare and release one bos descriptor in usb_reset_and_verify_device()
  ehci: remove debugging statement with ehci statistics in ehci_stop()
  ehci: remove duplicate debug_async_open() prototype in ehci-dbg.c
  ehci: enable debugging code when CONFIG_DYNAMIC_DEBUG is set
  ehci: remove ehci_vdbg() verbose debugging statements
  Documentation sysfs-bus-usb: Document which files are used by libusb
  Documentation sysfs-bus-usb: Document the speed file used by libusb
  Documentation sysfs-bus-usb: Move files with known users to stable
  USB: fix build error when CONFIG_PM_SLEEP isn't enabled
  usb: r8a66597-hcd: use platform_{get,set}_drvdata()
  usb: phy-tegra-usb: use platform_{get,set}_drvdata()
  usb: acm gadget: Null termintate strings table
  dma: cppi41: off by one in desc_to_chan()
  xhci: Fix warning introduced by disabling runtime PM.
  dev-core: fix build break when DEBUG is enabled
  USB: OHCI: Allow runtime PM without system sleep
  usb: ohci-at91: remove unnecessary dev_set_drvdata()
  usb: renesas_usbhs: use platform_{get,set}_drvdata()
  usb: fotg210-udc: use platform_{get,set}_drvdata()
  ...

7 files changed, 293 insertions, 39 deletions

diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
index dc9dc8c87f15..20c2ff2ba07e 100644
--- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt
+++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
@@ -1,35 +1,197 @@
-AM33XX MUSB GLUE
- - compatible : Should be "ti,musb-am33xx"
- - reg : offset and length of register sets, first usbss, then for musb instances
- - interrupts : usbss, musb instance interrupts in order
- - ti,hwmods : must be "usb_otg_hs"
- - multipoint : Should be "1" indicating the musb controller supports
-   multipoint. This is a MUSB configuration-specific setting.
- - num-eps : Specifies the number of endpoints. This is also a
-   MUSB configuration-specific setting. Should be set to "16"
- - ram-bits : Specifies the ram address size. Should be set to "12"
- - port0-mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
-   represents PERIPHERAL.
- - port1-mode : Should be "1" to represent HOST. "3" signifies OTG and "2"
-   represents PERIPHERAL.
- - power : Should be "250". This signifies the controller can supply up to
-   500mA when operating in host mode.
+  AM33xx MUSB
+~~~~~~~~~~~~~~~
+- compatible: ti,am33xx-usb
+- reg: offset and length of the usbss register sets
+- ti,hwmods : must be "usb_otg_hs"
+
+The glue layer contains multiple child nodes. It is required the have
+at least a control module node, USB node and a PHY node. The second USB
+node and its PHY node is optional. The DMA node is also optional.
+
+Reset module
+~~~~~~~~~~~~
+- compatible: ti,am335x-usb-ctrl-module
+- reg: offset and length of the "USB control registers" in the "Control
+  Module" block. A second offset and length for the USB wake up control
+  in the same memory block.
+- reg-names: "phy_ctrl" for the "USB control registers" and "wakeup" for
+  the USB wake up control register.
+
+USB PHY
+~~~~~~~
+compatible: ti,am335x-usb-phy
+reg: offset and length of the "USB PHY" register space
+ti,ctrl_mod: reference to the "reset module" node
+reg-names: phy
+The PHY should have a "phy" alias numbered properly in the alias
+node.
+
+USB
+~~~
+- compatible: ti,musb-am33xx
+- reg: offset and length of "USB Controller Registers", and offset and
+  length of "USB Core" register space.
+- reg-names: control for the ""USB Controller Registers" and "mc" for
+  "USB Core" register space
+- interrupts: USB interrupt number
+- interrupt-names: mc
+- dr_mode: Should be one of "host", "peripheral" or "otg".
+- mentor,multipoint: Should be "1" indicating the musb controller supports
+  multipoint. This is a MUSB configuration-specific setting.
+- mentor,num-eps: Specifies the number of endpoints. This is also a
+  MUSB configuration-specific setting. Should be set to "16"
+- mentor,ram-bits: Specifies the ram address size. Should be set to "12"
+- mentor,power: Should be "500". This signifies the controller can supply up to
+  500mA when operating in host mode.
+- phys: reference to the USB phy
+- dmas: specifies the dma channels
+- dma-names: specifies the names of the channels. Use "rxN" for receive
+  and "txN" for transmit endpoints. N specifies the endpoint number.
+
+The controller should have an "usb" alias numbered properly in the alias
+node.
+
+DMA
+~~~
+- compatible: ti,am3359-cppi41
+- reg: offset and length of the following register spaces: USBSS, USB
+  CPPI DMA Controller, USB CPPI DMA Scheduler, USB Queue Manager
+- reg-names: glue, controller, scheduler, queuemgr
+- #dma-cells: should be set to 2. The first number represents the
+  endpoint number (0 … 14 for endpoints 1 … 15 on instance 0 and 15 … 29
+  for endpoints 1 … 15 on instance 1). The second number is 0 for RX and
+  1 for TX transfers.
+- #dma-channels: should be set to 30 representing the 15 endpoints for
+  each USB instance.
 
 Example:
+~~~~~~~~
+The following example contains all the nodes as used on am335x-evm:
+
+aliases {
+	usb0 = &usb0;
+	usb1 = &usb1;
+	phy0 = &usb0_phy;
+	phy1 = &usb1_phy;
+};
 
-usb@47400000  {
-	compatible = "ti,musb-am33xx";
-	reg = <0x47400000 0x1000	/* usbss */
-	       0x47401000 0x800		/* musb instance 0 */
-	       0x47401800 0x800>;	/* musb instance 1 */
-	interrupts = <17		/* usbss */
-		      18		/* musb instance 0 */
-		      19>;		/* musb instance 1 */
-	multipoint = <1>;
-	num-eps = <16>;
-	ram-bits = <12>;
-	port0-mode = <3>;
-	port1-mode = <3>;
-	power = <250>;
+usb: usb@47400000 {
+	compatible = "ti,am33xx-usb";
+	reg = <0x47400000 0x1000>;
+	ranges;
+	#address-cells = <1>;
+	#size-cells = <1>;
 	ti,hwmods = "usb_otg_hs";
+
+	ctrl_mod: control@44e10000 {
+		compatible = "ti,am335x-usb-ctrl-module";
+		reg = <0x44e10620 0x10
+			0x44e10648 0x4>;
+		reg-names = "phy_ctrl", "wakeup";
+	};
+
+	usb0_phy: usb-phy@47401300 {
+		compatible = "ti,am335x-usb-phy";
+		reg = <0x47401300 0x100>;
+		reg-names = "phy";
+		ti,ctrl_mod = <&ctrl_mod>;
+	};
+
+	usb0: usb@47401000 {
+		compatible = "ti,musb-am33xx";
+		reg = <0x47401400 0x400
+			0x47401000 0x200>;
+		reg-names = "mc", "control";
+
+		interrupts = <18>;
+		interrupt-names = "mc";
+		dr_mode = "otg"
+		mentor,multipoint = <1>;
+		mentor,num-eps = <16>;
+		mentor,ram-bits = <12>;
+		mentor,power = <500>;
+		phys = <&usb0_phy>;
+
+		dmas = <&cppi41dma  0 0 &cppi41dma  1 0
+			&cppi41dma  2 0 &cppi41dma  3 0
+			&cppi41dma  4 0 &cppi41dma  5 0
+			&cppi41dma  6 0 &cppi41dma  7 0
+			&cppi41dma  8 0 &cppi41dma  9 0
+			&cppi41dma 10 0 &cppi41dma 11 0
+			&cppi41dma 12 0 &cppi41dma 13 0
+			&cppi41dma 14 0 &cppi41dma  0 1
+			&cppi41dma  1 1 &cppi41dma  2 1
+			&cppi41dma  3 1 &cppi41dma  4 1
+			&cppi41dma  5 1 &cppi41dma  6 1
+			&cppi41dma  7 1 &cppi41dma  8 1
+			&cppi41dma  9 1 &cppi41dma 10 1
+			&cppi41dma 11 1 &cppi41dma 12 1
+			&cppi41dma 13 1 &cppi41dma 14 1>;
+		dma-names =
+			"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+			"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+			"rx14", "rx15",
+			"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+			"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+			"tx14", "tx15";
+	};
+
+	usb1_phy: usb-phy@47401b00 {
+		compatible = "ti,am335x-usb-phy";
+		reg = <0x47401b00 0x100>;
+		reg-names = "phy";
+		ti,ctrl_mod = <&ctrl_mod>;
+	};
+
+	usb1: usb@47401800 {
+		compatible = "ti,musb-am33xx";
+		reg = <0x47401c00 0x400
+			0x47401800 0x200>;
+		reg-names = "mc", "control";
+		interrupts = <19>;
+		interrupt-names = "mc";
+		dr_mode = "host"
+		mentor,multipoint = <1>;
+		mentor,num-eps = <16>;
+		mentor,ram-bits = <12>;
+		mentor,power = <500>;
+		phys = <&usb1_phy>;
+
+		dmas = <&cppi41dma 15 0 &cppi41dma 16 0
+			&cppi41dma 17 0 &cppi41dma 18 0
+			&cppi41dma 19 0 &cppi41dma 20 0
+			&cppi41dma 21 0 &cppi41dma 22 0
+			&cppi41dma 23 0 &cppi41dma 24 0
+			&cppi41dma 25 0 &cppi41dma 26 0
+			&cppi41dma 27 0 &cppi41dma 28 0
+			&cppi41dma 29 0 &cppi41dma 15 1
+			&cppi41dma 16 1 &cppi41dma 17 1
+			&cppi41dma 18 1 &cppi41dma 19 1
+			&cppi41dma 20 1 &cppi41dma 21 1
+			&cppi41dma 22 1 &cppi41dma 23 1
+			&cppi41dma 24 1 &cppi41dma 25 1
+			&cppi41dma 26 1 &cppi41dma 27 1
+			&cppi41dma 28 1 &cppi41dma 29 1>;
+		dma-names =
+			"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
+			"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
+			"rx14", "rx15",
+			"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
+			"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
+			"tx14", "tx15";
+	};
+
+	cppi41dma: dma-controller@07402000 {
+		compatible = "ti,am3359-cppi41";
+		reg =  <0x47400000 0x1000
+			0x47402000 0x1000
+			0x47403000 0x1000
+			0x47404000 0x4000>;
+		reg-names = "glue", "controller", "scheduler", "queuemgr";
+		interrupts = <17>;
+		interrupt-names = "glue";
+		#dma-cells = <2>;
+		#dma-channels = <30>;
+		#dma-requests = <256>;
+	};
 };
diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
index 7a95c651ceb3..e807635f9e1c 100644
--- a/Documentation/devicetree/bindings/usb/dwc3.txt
+++ b/Documentation/devicetree/bindings/usb/dwc3.txt
@@ -3,10 +3,12 @@ synopsys DWC3 CORE
 DWC3- USB3 CONTROLLER
 
 Required properties:
- - compatible: must be "synopsys,dwc3"
+ - compatible: must be "snps,dwc3"
  - reg : Address and length of the register set for the device
  - interrupts: Interrupts used by the dwc3 controller.
- - usb-phy : array of phandle for the PHY device
+ - usb-phy : array of phandle for the PHY device.  The first element
+   in the array is expected to be a handle to the USB2/HS PHY and
+   the second element is expected to be a handle to the USB3/SS PHY
 
 Optional properties:
  - tx-fifo-resize: determines if the FIFO *has* to be reallocated.
@@ -14,7 +16,7 @@ Optional properties:
 This is usually a subnode to DWC3 glue to which it is connected.
 
 dwc3@4a030000 {
-	compatible = "synopsys,dwc3";
+	compatible = "snps,dwc3";
 	reg = <0x4a030000 0xcfff>;
 	interrupts = <0 92 4>
 	usb-phy = <&usb2_phy>, <&usb3,phy>;
diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt
new file mode 100644
index 000000000000..477d5bb5e51c
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/generic.txt
@@ -0,0 +1,24 @@
+Generic USB Properties
+
+Optional properties:
+ - maximum-speed: tells USB controllers we want to work up to a certain
+			speed. Valid arguments are "super-speed", "high-speed",
+			"full-speed" and "low-speed". In case this isn't passed
+			via DT, USB controllers should default to their maximum
+			HW capability.
+ - dr_mode: tells Dual-Role USB controllers that we want to work on a
+			particular mode. Valid arguments are "host",
+			"peripheral" and "otg". In case this attribute isn't
+			passed via DT, USB DRD controllers should default to
+			OTG.
+
+This is an attribute to a USB controller such as:
+
+dwc3@4a030000 {
+	compatible = "synopsys,dwc3";
+	reg = <0x4a030000 0xcfff>;
+	interrupts = <0 92 4>
+	usb-phy = <&usb2_phy>, <&usb3,phy>;
+	maximum-speed = "super-speed";
+	dr_mode = "otg";
+};
diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt
index c4c9e9e664aa..ba797d3e6326 100644
--- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt
+++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt
@@ -3,7 +3,7 @@ Tegra SOC USB PHY
 The device node for Tegra SOC USB PHY:
 
 Required properties :
- - compatible : Should be "nvidia,tegra20-usb-phy".
+ - compatible : Should be "nvidia,tegra<chip>-usb-phy".
  - reg : Defines the following set of registers, in the order listed:
    - The PHY's own register set.
      Always present.
@@ -24,17 +24,26 @@ Required properties :
 Required properties for phy_type == ulpi:
   - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
 
-Required PHY timing params for utmi phy:
+Required PHY timing params for utmi phy, for all chips:
   - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before
     start of sync launches RxActive
   - nvidia,elastic-limit : Variable FIFO Depth of elastic input store
   - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait
     before declare IDLE.
   - nvidia,term-range-adj : Range adjusment on terminations
-  - nvidia,xcvr-setup : HS driver output control
+  - Either one of the following for HS driver output control:
+    - nvidia,xcvr-setup : integer, uses the provided value.
+    - nvidia,xcvr-setup-use-fuses : boolean, indicates that the value is read
+      from the on-chip fuses
+    If both are provided, nvidia,xcvr-setup-use-fuses takes precedence.
   - nvidia,xcvr-lsfslew : LS falling slew rate control.
   - nvidia,xcvr-lsrslew :  LS rising slew rate control.
 
+Required PHY timing params for utmi phy, only on Tegra30 and above:
+  - nvidia,xcvr-hsslew : HS slew rate control.
+  - nvidia,hssquelch-level : HS squelch detector level.
+  - nvidia,hsdiscon-level : HS disconnect detector level.
+
 Optional properties:
   - nvidia,has-legacy-mode : boolean indicates whether this controller can
     operate in legacy mode (as APX 2500 / 2600). In legacy mode some
@@ -48,5 +57,5 @@ Optional properties:
       peripheral means it is device controller
       otg means it can operate as either ("on the go")
 
-Required properties for dr_mode == otg:
+VBUS control (required for dr_mode == otg, optional for dr_mode == host):
   - vbus-supply: regulator for VBUS
diff --git a/Documentation/devicetree/bindings/usb/samsung-hsotg.txt b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt
new file mode 100644
index 000000000000..b83d428a265e
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt
@@ -0,0 +1,40 @@
+Samsung High Speed USB OTG controller
+-----------------------------
+
+The Samsung HSOTG IP can be found on Samsung SoCs, from S3C6400 onwards.
+It gives functionality of OTG-compliant USB 2.0 host and device with
+support for USB 2.0 high-speed (480Mbps) and full-speed (12 Mbps)
+operation.
+
+Currently only device mode is supported.
+
+Binding details
+-----
+
+Required properties:
+- compatible: "samsung,s3c6400-hsotg" should be used for all currently
+    supported SoC,
+- interrupt-parent: phandle for the interrupt controller to which the
+    interrupt signal of the HSOTG block is routed,
+- interrupts: specifier of interrupt signal of interrupt controller,
+    according to bindings of interrupt controller,
+- clocks: contains an array of clock specifiers:
+    - first entry: OTG clock
+- clock-names: contains array of clock names:
+    - first entry: must be "otg"
+- vusb_d-supply: phandle to voltage regulator of digital section,
+- vusb_a-supply: phandle to voltage regulator of analog section.
+
+Example
+-----
+
+	hsotg@12480000 {
+		compatible = "samsung,s3c6400-hsotg";
+		reg = <0x12480000 0x20000>;
+		interrupts = <0 71 0>;
+		clocks = <&clock 305>;
+		clock-names = "otg";
+		vusb_d-supply = <&vusb_reg>;
+		vusb_a-supply = <&vusbdac_reg>;
+	};
+
diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt
new file mode 100644
index 000000000000..5752df0e17a2
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt
@@ -0,0 +1,14 @@
+USB xHCI controllers
+
+Required properties:
+  - compatible: should be "xhci-platform".
+  - reg: should contain address and length of the standard XHCI
+    register set for the device.
+  - interrupts: one XHCI interrupt should be described here.
+
+Example:
+	usb@f0931000 {
+		compatible = "xhci-platform";
+		reg = <0xf0931000 0x8c8>;
+		interrupts = <0x0 0x4e 0x0>;
+	};
diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt
index 8c5be48b43c8..a018da4a7ad7 100644
--- a/Documentation/devicetree/bindings/usb/usb3503.txt
+++ b/Documentation/devicetree/bindings/usb/usb3503.txt
@@ -1,8 +1,11 @@
 SMSC USB3503 High-Speed Hub Controller
 
 Required properties:
-- compatible: Should be "smsc,usb3503".
-- reg: Specifies the i2c slave address, it should be 0x08.
+- compatible: Should be "smsc,usb3503" or "smsc,usb3503a".
+
+Optional properties:
+- reg: Specifies the i2c slave address, it is required and should be 0x08
+       if I2C is used.
 - connect-gpios: Should specify GPIO for connect.
 - disabled-ports: Should specify the ports unused.
 	'1' or '2' or '3' are availe for this property to describe the port