summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorRemy Bohmer <linux@bohmer.net>2008-02-08 04:21:01 -0800
committerLinus Torvalds <torvalds@woody.linux-foundation.org>2008-02-08 09:22:37 -0800
commitb843aa216c4da250c6732cd76430d73a6589beb5 (patch)
tree4c830b7749d565c6fd1010d889dc812607b1acde
parenta1cfac48ba4c7481bb749e0f4f37c85cb871b2d1 (diff)
downloadblackbird-op-linux-b843aa216c4da250c6732cd76430d73a6589beb5.tar.gz
blackbird-op-linux-b843aa216c4da250c6732cd76430d73a6589beb5.zip
atmel_serial: clean up the code
Clean up the atmel_serial driver to conform the coding rules. It contains no functional change. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <linux@maxim.org.za> Tested-by: Marc Pignat <marc.pignat@hevs.ch> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-rw-r--r--drivers/serial/atmel_serial.c255
1 files changed, 150 insertions, 105 deletions
diff --git a/drivers/serial/atmel_serial.c b/drivers/serial/atmel_serial.c
index 60f52904aad0..bb9c3574caa9 100644
--- a/drivers/serial/atmel_serial.c
+++ b/drivers/serial/atmel_serial.c
@@ -73,6 +73,7 @@
#define ATMEL_ISR_PASS_LIMIT 256
+/* UART registers. CR is write-only, hence no GET macro */
#define UART_PUT_CR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_CR)
#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR)
#define UART_PUT_MR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_MR)
@@ -86,8 +87,6 @@
#define UART_PUT_BRGR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR)
#define UART_PUT_RTOR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR)
-// #define UART_GET_CR(port) __raw_readl((port)->membase + ATMEL_US_CR) // is write-only
-
/* PDC registers */
#define UART_PUT_PTCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR)
#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR)
@@ -100,8 +99,6 @@
#define UART_PUT_TPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR)
#define UART_PUT_TCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR)
-//#define UART_PUT_TNPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TNPR)
-//#define UART_PUT_TNCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TNCR)
static int (*atmel_open_hook)(struct uart_port *);
static void (*atmel_close_hook)(struct uart_port *);
@@ -141,8 +138,8 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
#ifdef CONFIG_ARCH_AT91RM9200
if (cpu_is_at91rm9200()) {
/*
- * AT91RM9200 Errata #39: RTS0 is not internally connected to PA21.
- * We need to drive the pin manually.
+ * AT91RM9200 Errata #39: RTS0 is not internally connected
+ * to PA21. We need to drive the pin manually.
*/
if (port->mapbase == AT91RM9200_BASE_US0) {
if (mctrl & TIOCM_RTS)
@@ -227,7 +224,8 @@ static void atmel_stop_rx(struct uart_port *port)
*/
static void atmel_enable_ms(struct uart_port *port)
{
- UART_PUT_IER(port, ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC | ATMEL_US_CTSIC);
+ UART_PUT_IER(port, ATMEL_US_RIIC | ATMEL_US_DSRIC
+ | ATMEL_US_DCDIC | ATMEL_US_CTSIC);
}
/*
@@ -246,7 +244,7 @@ static void atmel_break_ctl(struct uart_port *port, int break_state)
*/
static void atmel_rx_chars(struct uart_port *port)
{
- struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
+ struct atmel_uart_port *atmel_port = (struct atmel_uart_port *)port;
struct tty_struct *tty = port->info->tty;
unsigned int status, ch, flg;
@@ -265,10 +263,12 @@ static void atmel_rx_chars(struct uart_port *port)
if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
| ATMEL_US_OVRE | ATMEL_US_RXBRK)
|| atmel_port->break_active)) {
- UART_PUT_CR(port, ATMEL_US_RSTSTA); /* clear error */
+ /* clear error */
+ UART_PUT_CR(port, ATMEL_US_RSTSTA);
if (status & ATMEL_US_RXBRK
&& !atmel_port->break_active) {
- status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME); /* ignore side-effect */
+ /* ignore side-effect */
+ status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
port->icount.brk++;
atmel_port->break_active = 1;
UART_PUT_IER(port, ATMEL_US_RXBRK);
@@ -308,7 +308,7 @@ static void atmel_rx_chars(struct uart_port *port)
uart_insert_char(port, status, ATMEL_US_OVRE, ch, flg);
- ignore_char:
+ignore_char:
status = UART_GET_CSR(port);
}
@@ -349,44 +349,73 @@ static void atmel_tx_chars(struct uart_port *port)
}
/*
+ * receive interrupt handler.
+ */
+static void
+atmel_handle_receive(struct uart_port *port, unsigned int pending)
+{
+ struct atmel_uart_port *atmel_port = (struct atmel_uart_port *)port;
+
+ /* Interrupt receive */
+ if (pending & ATMEL_US_RXRDY)
+ atmel_rx_chars(port);
+ else if (pending & ATMEL_US_RXBRK) {
+ /*
+ * End of break detected. If it came along with a
+ * character, atmel_rx_chars will handle it.
+ */
+ UART_PUT_CR(port, ATMEL_US_RSTSTA);
+ UART_PUT_IDR(port, ATMEL_US_RXBRK);
+ atmel_port->break_active = 0;
+ }
+}
+
+/*
+ * transmit interrupt handler.
+ */
+static void
+atmel_handle_transmit(struct uart_port *port, unsigned int pending)
+{
+ /* Interrupt transmit */
+ if (pending & ATMEL_US_TXRDY)
+ atmel_tx_chars(port);
+}
+
+/*
+ * status flags interrupt handler.
+ */
+static void
+atmel_handle_status(struct uart_port *port, unsigned int pending,
+ unsigned int status)
+{
+ /* TODO: All reads to CSR will clear these interrupts! */
+ if (pending & ATMEL_US_RIIC)
+ port->icount.rng++;
+ if (pending & ATMEL_US_DSRIC)
+ port->icount.dsr++;
+ if (pending & ATMEL_US_DCDIC)
+ uart_handle_dcd_change(port, !(status & ATMEL_US_DCD));
+ if (pending & ATMEL_US_CTSIC)
+ uart_handle_cts_change(port, !(status & ATMEL_US_CTS));
+ if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC
+ | ATMEL_US_CTSIC))
+ wake_up_interruptible(&port->info->delta_msr_wait);
+}
+
+/*
* Interrupt handler
*/
static irqreturn_t atmel_interrupt(int irq, void *dev_id)
{
struct uart_port *port = dev_id;
- struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
unsigned int status, pending, pass_counter = 0;
status = UART_GET_CSR(port);
pending = status & UART_GET_IMR(port);
while (pending) {
- /* Interrupt receive */
- if (pending & ATMEL_US_RXRDY)
- atmel_rx_chars(port);
- else if (pending & ATMEL_US_RXBRK) {
- /*
- * End of break detected. If it came along
- * with a character, atmel_rx_chars will
- * handle it.
- */
- UART_PUT_CR(port, ATMEL_US_RSTSTA);
- UART_PUT_IDR(port, ATMEL_US_RXBRK);
- atmel_port->break_active = 0;
- }
-
- // TODO: All reads to CSR will clear these interrupts!
- if (pending & ATMEL_US_RIIC) port->icount.rng++;
- if (pending & ATMEL_US_DSRIC) port->icount.dsr++;
- if (pending & ATMEL_US_DCDIC)
- uart_handle_dcd_change(port, !(status & ATMEL_US_DCD));
- if (pending & ATMEL_US_CTSIC)
- uart_handle_cts_change(port, !(status & ATMEL_US_CTS));
- if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC | ATMEL_US_CTSIC))
- wake_up_interruptible(&port->info->delta_msr_wait);
-
- /* Interrupt transmit */
- if (pending & ATMEL_US_TXRDY)
- atmel_tx_chars(port);
+ atmel_handle_receive(port, pending);
+ atmel_handle_status(port, pending, status);
+ atmel_handle_transmit(port, pending);
if (pass_counter++ > ATMEL_ISR_PASS_LIMIT)
break;
@@ -414,7 +443,8 @@ static int atmel_startup(struct uart_port *port)
/*
* Allocate the IRQ
*/
- retval = request_irq(port->irq, atmel_interrupt, IRQF_SHARED, "atmel_serial", port);
+ retval = request_irq(port->irq, atmel_interrupt, IRQF_SHARED,
+ "atmel_serial", port);
if (retval) {
printk("atmel_serial: atmel_startup - Can't get irq\n");
return retval;
@@ -436,9 +466,11 @@ static int atmel_startup(struct uart_port *port)
* Finally, enable the serial port
*/
UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
- UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN); /* enable xmit & rcvr */
+ /* enable xmit & rcvr */
+ UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
- UART_PUT_IER(port, ATMEL_US_RXRDY); /* enable receive only */
+ /* enable receive only */
+ UART_PUT_IER(port, ATMEL_US_RXRDY);
return 0;
}
@@ -470,45 +502,48 @@ static void atmel_shutdown(struct uart_port *port)
/*
* Power / Clock management.
*/
-static void atmel_serial_pm(struct uart_port *port, unsigned int state, unsigned int oldstate)
+static void atmel_serial_pm(struct uart_port *port, unsigned int state,
+ unsigned int oldstate)
{
- struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
+ struct atmel_uart_port *atmel_port = (struct atmel_uart_port *)port;
switch (state) {
- case 0:
- /*
- * Enable the peripheral clock for this serial port.
- * This is called on uart_open() or a resume event.
- */
- clk_enable(atmel_port->clk);
- break;
- case 3:
- /*
- * Disable the peripheral clock for this serial port.
- * This is called on uart_close() or a suspend event.
- */
- clk_disable(atmel_port->clk);
- break;
- default:
- printk(KERN_ERR "atmel_serial: unknown pm %d\n", state);
+ case 0:
+ /*
+ * Enable the peripheral clock for this serial port.
+ * This is called on uart_open() or a resume event.
+ */
+ clk_enable(atmel_port->clk);
+ break;
+ case 3:
+ /*
+ * Disable the peripheral clock for this serial port.
+ * This is called on uart_close() or a suspend event.
+ */
+ clk_disable(atmel_port->clk);
+ break;
+ default:
+ printk(KERN_ERR "atmel_serial: unknown pm %d\n", state);
}
}
/*
* Change the port parameters
*/
-static void atmel_set_termios(struct uart_port *port, struct ktermios * termios, struct ktermios * old)
+static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
{
unsigned long flags;
unsigned int mode, imr, quot, baud;
/* Get current mode register */
- mode = UART_GET_MR(port) & ~(ATMEL_US_USCLKS | ATMEL_US_CHRL | ATMEL_US_NBSTOP | ATMEL_US_PAR);
+ mode = UART_GET_MR(port) & ~(ATMEL_US_USCLKS | ATMEL_US_CHRL
+ | ATMEL_US_NBSTOP | ATMEL_US_PAR);
- baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+ baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
quot = uart_get_divisor(port, baud);
- if (quot > 65535) { /* BRGR is 16-bit, so switch to slower clock */
+ if (quot > 65535) { /* BRGR is 16-bit, so switch to slower clock */
quot /= 8;
mode |= ATMEL_US_USCLKS_MCK_DIV8;
}
@@ -535,18 +570,17 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios * termios,
/* parity */
if (termios->c_cflag & PARENB) {
- if (termios->c_cflag & CMSPAR) { /* Mark or Space parity */
+ /* Mark or Space parity */
+ if (termios->c_cflag & CMSPAR) {
if (termios->c_cflag & PARODD)
mode |= ATMEL_US_PAR_MARK;
else
mode |= ATMEL_US_PAR_SPACE;
- }
- else if (termios->c_cflag & PARODD)
+ } else if (termios->c_cflag & PARODD)
mode |= ATMEL_US_PAR_ODD;
else
mode |= ATMEL_US_PAR_EVEN;
- }
- else
+ } else
mode |= ATMEL_US_PAR_NONE;
spin_lock_irqsave(&port->lock, flags);
@@ -572,16 +606,16 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios * termios,
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= ATMEL_US_OVRE;
}
-
- // TODO: Ignore all characters if CREAD is set.
+ /* TODO: Ignore all characters if CREAD is set.*/
/* update the per-port timeout */
uart_update_timeout(port, termios->c_cflag, baud);
- /* disable interrupts and drain transmitter */
- imr = UART_GET_IMR(port); /* get interrupt mask */
- UART_PUT_IDR(port, -1); /* disable all interrupts */
- while (!(UART_GET_CSR(port) & ATMEL_US_TXEMPTY)) { barrier(); }
+ /* save/disable interrupts and drain transmitter */
+ imr = UART_GET_IMR(port);
+ UART_PUT_IDR(port, -1);
+ while (!(UART_GET_CSR(port) & ATMEL_US_TXEMPTY))
+ barrier();
/* disable receiver and transmitter */
UART_PUT_CR(port, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
@@ -707,7 +741,8 @@ static struct uart_ops atmel_pops = {
/*
* Configure the port from the platform device resource info.
*/
-static void __devinit atmel_init_port(struct atmel_uart_port *atmel_port, struct platform_device *pdev)
+static void __devinit atmel_init_port(struct atmel_uart_port *atmel_port,
+ struct platform_device *pdev)
{
struct uart_port *port = &atmel_port->uart;
struct atmel_uart_data *data = pdev->dev.platform_data;
@@ -730,7 +765,8 @@ static void __devinit atmel_init_port(struct atmel_uart_port *atmel_port, struct
port->membase = NULL;
}
- if (!atmel_port->clk) { /* for console, the clock could already be configured */
+ /* for console, the clock could already be configured */
+ if (!atmel_port->clk) {
atmel_port->clk = clk_get(&pdev->dev, "usart");
clk_enable(atmel_port->clk);
port->uartclk = clk_get_rate(atmel_port->clk);
@@ -754,7 +790,6 @@ void __init atmel_register_uart_fns(struct atmel_port_fns *fns)
atmel_pops.set_wake = fns->set_wake;
}
-
#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
static void atmel_console_putchar(struct uart_port *port, int ch)
{
@@ -772,28 +807,30 @@ static void atmel_console_write(struct console *co, const char *s, u_int count)
unsigned int status, imr;
/*
- * First, save IMR and then disable interrupts
+ * First, save IMR and then disable interrupts
*/
- imr = UART_GET_IMR(port); /* get interrupt mask */
+ imr = UART_GET_IMR(port);
UART_PUT_IDR(port, ATMEL_US_RXRDY | ATMEL_US_TXRDY);
uart_console_write(port, s, count, atmel_console_putchar);
/*
- * Finally, wait for transmitter to become empty
- * and restore IMR
+ * Finally, wait for transmitter to become empty
+ * and restore IMR
*/
do {
status = UART_GET_CSR(port);
} while (!(status & ATMEL_US_TXRDY));
- UART_PUT_IER(port, imr); /* set interrupts back the way they were */
+ /* set interrupts back the way they were */
+ UART_PUT_IER(port, imr);
}
/*
- * If the port was already initialised (eg, by a boot loader), try to determine
- * the current setup.
+ * If the port was already initialised (eg, by a boot loader),
+ * try to determine the current setup.
*/
-static void __init atmel_console_get_options(struct uart_port *port, int *baud, int *parity, int *bits)
+static void __init atmel_console_get_options(struct uart_port *port, int *baud,
+ int *parity, int *bits)
{
unsigned int mr, quot;
@@ -835,10 +872,12 @@ static int __init atmel_console_setup(struct console *co, char *options)
int parity = 'n';
int flow = 'n';
- if (port->membase == 0) /* Port not initialized yet - delay setup */
+ if (port->membase == NULL) {
+ /* Port not initialized yet - delay setup */
return -ENODEV;
+ }
- UART_PUT_IDR(port, -1); /* disable interrupts */
+ UART_PUT_IDR(port, -1);
UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
@@ -870,13 +909,16 @@ static struct console atmel_console = {
static int __init atmel_console_init(void)
{
if (atmel_default_console_device) {
- add_preferred_console(ATMEL_DEVICENAME, atmel_default_console_device->id, NULL);
- atmel_init_port(&(atmel_ports[atmel_default_console_device->id]), atmel_default_console_device);
+ add_preferred_console(ATMEL_DEVICENAME,
+ atmel_default_console_device->id, NULL);
+ atmel_init_port(&atmel_ports[atmel_default_console_device->id],
+ atmel_default_console_device);
register_console(&atmel_console);
}
return 0;
}
+
console_initcall(atmel_console_init);
/*
@@ -884,11 +926,13 @@ console_initcall(atmel_console_init);
*/
static int __init atmel_late_console_init(void)
{
- if (atmel_default_console_device && !(atmel_console.flags & CON_ENABLED))
+ if (atmel_default_console_device
+ && !(atmel_console.flags & CON_ENABLED))
register_console(&atmel_console);
return 0;
}
+
core_initcall(atmel_late_console_init);
#else
@@ -896,22 +940,24 @@ core_initcall(atmel_late_console_init);
#endif
static struct uart_driver atmel_uart = {
- .owner = THIS_MODULE,
- .driver_name = "atmel_serial",
- .dev_name = ATMEL_DEVICENAME,
- .major = SERIAL_ATMEL_MAJOR,
- .minor = MINOR_START,
- .nr = ATMEL_MAX_UART,
- .cons = ATMEL_CONSOLE_DEVICE,
+ .owner = THIS_MODULE,
+ .driver_name = "atmel_serial",
+ .dev_name = ATMEL_DEVICENAME,
+ .major = SERIAL_ATMEL_MAJOR,
+ .minor = MINOR_START,
+ .nr = ATMEL_MAX_UART,
+ .cons = ATMEL_CONSOLE_DEVICE,
};
#ifdef CONFIG_PM
-static int atmel_serial_suspend(struct platform_device *pdev, pm_message_t state)
+static int atmel_serial_suspend(struct platform_device *pdev,
+ pm_message_t state)
{
struct uart_port *port = platform_get_drvdata(pdev);
- struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
+ struct atmel_uart_port *atmel_port = (struct atmel_uart_port *)port;
- if (device_may_wakeup(&pdev->dev) && !at91_suspend_entering_slow_clock())
+ if (device_may_wakeup(&pdev->dev)
+ && !at91_suspend_entering_slow_clock())
enable_irq_wake(port->irq);
else {
uart_suspend_port(&atmel_uart, port);
@@ -924,13 +970,12 @@ static int atmel_serial_suspend(struct platform_device *pdev, pm_message_t state
static int atmel_serial_resume(struct platform_device *pdev)
{
struct uart_port *port = platform_get_drvdata(pdev);
- struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
+ struct atmel_uart_port *atmel_port = (struct atmel_uart_port *)port;
if (atmel_port->suspended) {
uart_resume_port(&atmel_uart, port);
atmel_port->suspended = 0;
- }
- else
+ } else
disable_irq_wake(port->irq);
return 0;
@@ -960,7 +1005,7 @@ static int __devinit atmel_serial_probe(struct platform_device *pdev)
static int __devexit atmel_serial_remove(struct platform_device *pdev)
{
struct uart_port *port = platform_get_drvdata(pdev);
- struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
+ struct atmel_uart_port *atmel_port = (struct atmel_uart_port *)port;
int ret = 0;
clk_disable(atmel_port->clk);
OpenPOWER on IntegriCloud