blackbird-op-linux/drivers/net/ethernet/broadcom, branch master

net: systemport: Avoid RBUF stuck in Wake-on-LAN mode

2020-02-06T13:28:52+00:00

After a number of suspend and resume cycles, it is possible for the RBUF to be stuck in Wake-on-LAN mode, despite the MPD enable bit being cleared which instructed the RBUF to exit that mode. Avoid creating that problematic condition by clearing the RX_EN and TX_EN bits in the UniMAC prior to disable the Magic Packet Detector logic which is guaranteed to make the RBUF exit Wake-on-LAN mode. Fixes: 83e82f4c706b ("net: systemport: add Wake-on-LAN support") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2020-02-04T13:32:20+00:00

Pull networking fixes from David Miller: 1) Use after free in rxrpc_put_local(), from David Howells. 2) Fix 64-bit division error in mlxsw, from Nathan Chancellor. 3) Make sure we clear various bits of TCP state in response to tcp_disconnect(). From Eric Dumazet. 4) Fix netlink attribute policy in cls_rsvp, from Eric Dumazet. 5) txtimer must be deleted in stmmac suspend(), from Nicolin Chen. 6) Fix TC queue mapping in bnxt_en driver, from Michael Chan. 7) Various netdevsim fixes from Taehee Yoo (use of uninitialized data, snapshot panics, stack out of bounds, etc.) 8) cls_tcindex changes hash table size after allocating the table, fix from Cong Wang. 9) Fix regression in the enforcement of session ID uniqueness in l2tp. We only have to enforce uniqueness for IP based tunnels not UDP ones. From Ridge Kennedy. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (46 commits) gtp: use __GFP_NOWARN to avoid memalloc warning l2tp: Allow duplicate session creation with UDP r8152: Add MAC passthrough support to new device net_sched: fix an OOB access in cls_tcindex qed: Remove set but not used variable 'p_link' tc-testing: add missing 'nsPlugin' to basic.json tc-testing: fix eBPF tests failure on linux fresh clones net: hsr: fix possible NULL deref in hsr_handle_frame() netdevsim: remove unused sdev code netdevsim: use __GFP_NOWARN to avoid memalloc warning netdevsim: use IS_ERR instead of IS_ERR_OR_NULL for debugfs netdevsim: fix stack-out-of-bounds in nsim_dev_debugfs_init() netdevsim: fix panic in nsim_dev_take_snapshot_write() netdevsim: disable devlink reload when resources are being used netdevsim: fix using uninitialized resources bnxt_en: Fix TC queue mapping. bnxt_en: Fix logic that disables Bus Master during firmware reset. bnxt_en: Fix RDMA driver failure with SRIOV after firmware reset. bnxt_en: Refactor logic to re-enable SRIOV after firmware reset detected. net: stmmac: Delete txtimer in suspend() ...

bnxt_en: Fix TC queue mapping.

2020-02-03T23:06:45+00:00

The driver currently only calls netdev_set_tc_queue when the number of TCs is greater than 1. Instead, the comparison should be greater than or equal to 1. Even with 1 TC, we need to set the queue mapping. This bug can cause warnings when the number of TCs is changed back to 1. Fixes: 7809592d3e2e ("bnxt_en: Enable MSIX early in bnxt_init_one().") Signed-off-by: Michael Chan Signed-off-by: Jakub Kicinski

bnxt_en: Fix logic that disables Bus Master during firmware reset.

2020-02-03T23:06:45+00:00

The current logic that calls pci_disable_device() in __bnxt_close_nic() during firmware reset is flawed. If firmware is still alive, we're disabling the device too early, causing some firmware commands to not reach the firmware. Fix it by moving the logic to bnxt_reset_close(). If firmware is in fatal condition, we call pci_disable_device() before we free any of the rings to prevent DMA corruption of the freed rings. If firmware is still alive, we call pci_disable_device() after the last firmware message has been sent. Fixes: 3bc7d4a352ef ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.") Signed-off-by: Vasundhara Volam Signed-off-by: Michael Chan Signed-off-by: Jakub Kicinski

bnxt_en: Fix RDMA driver failure with SRIOV after firmware reset.

2020-02-03T23:06:45+00:00

bnxt_ulp_start() needs to be called before SRIOV is re-enabled after firmware reset. Re-enabling SRIOV may consume all the resources and may cause the RDMA driver to fail to get MSIX and other resources. Fix it by calling bnxt_ulp_start() first before calling bnxt_reenable_sriov(). We re-arrange the logic so that we call bnxt_ulp_start() and bnxt_reenable_sriov() in proper sequence in bnxt_fw_reset_task() and bnxt_open(). The former is the normal coordinated firmware reset sequence and the latter is firmware reset while the function is down. This new logic is now more straight forward and will now fix both scenarios. Fixes: f3a6d206c25a ("bnxt_en: Call bnxt_ulp_stop()/bnxt_ulp_start() during error recovery.") Reported-by: Vasundhara Volam Signed-off-by: Michael Chan Signed-off-by: Jakub Kicinski

bnxt_en: Refactor logic to re-enable SRIOV after firmware reset detected.

2020-02-03T23:06:45+00:00

Put the current logic in bnxt_open() to re-enable SRIOV after detecting firmware reset into a new function bnxt_reenable_sriov(). This call needs to be invoked in the firmware reset path also in the next patch. Signed-off-by: Michael Chan Signed-off-by: Jakub Kicinski

ocfs2/dlm: move BITS_TO_BYTES() to bitops.h for wider use

2020-01-31T18:30:36+00:00

There are users already and will be more of BITS_TO_BYTES() macro. Move it to bitops.h for wider use. In the case of ocfs2 the replacement is identical. As for bnx2x, there are two places where floor version is used. In the first case to calculate the amount of structures that can fit one memory page. In this case obviously the ceiling variant is correct and original code might have a potential bug, if amount of bits % 8 is not 0. In the second case the macro is used to calculate bytes transmitted in one microsecond. This will work for all speeds which is multiply of 1Gbps without any change, for the rest new code will give ceiling value, for instance 100Mbps will give 13 bytes, while old code gives 12 bytes and the arithmetically correct one is 12.5 bytes. Further the value is used to setup timer threshold which in any case has its own margins due to certain resolution. I don't see here an issue with slightly shifting thresholds for low speed connections, the card is supposed to utilize highest available rate, which is usually 10Gbps. Link: http://lkml.kernel.org/r/20200108121316.22411-1-andriy.shevchenko@linux.intel.com Signed-off-by: Andy Shevchenko Reviewed-by: Joseph Qi Acked-by: Sudarsana Reddy Kalluru Cc: Mark Fasheh Cc: Joel Becker Cc: Junxiao Bi Cc: Changwei Ge Cc: Gang He Cc: Jun Piao Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

2020-01-29T00:02:33+00:00

Pull networking updates from David Miller: 1) Add WireGuard 2) Add HE and TWT support to ath11k driver, from John Crispin. 3) Add ESP in TCP encapsulation support, from Sabrina Dubroca. 4) Add variable window congestion control to TIPC, from Jon Maloy. 5) Add BCM84881 PHY driver, from Russell King. 6) Start adding netlink support for ethtool operations, from Michal Kubecek. 7) Add XDP drop and TX action support to ena driver, from Sameeh Jubran. 8) Add new ipv4 route notifications so that mlxsw driver does not have to handle identical routes itself. From Ido Schimmel. 9) Add BPF dynamic program extensions, from Alexei Starovoitov. 10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes. 11) Add support for macsec HW offloading, from Antoine Tenart. 12) Add initial support for MPTCP protocol, from Christoph Paasch, Matthieu Baerts, Florian Westphal, Peter Krystad, and many others. 13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu Cherian, and others. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits) net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC udp: segment looped gso packets correctly netem: change mailing list qed: FW 8.42.2.0 debug features qed: rt init valid initialization changed qed: Debug feature: ilt and mdump qed: FW 8.42.2.0 Add fw overlay feature qed: FW 8.42.2.0 HSI changes qed: FW 8.42.2.0 iscsi/fcoe changes qed: Add abstraction for different hsi values per chip qed: FW 8.42.2.0 Additional ll2 type qed: Use dmae to write to widebus registers in fw_funcs qed: FW 8.42.2.0 Parser offsets modified qed: FW 8.42.2.0 Queue Manager changes qed: FW 8.42.2.0 Expose new registers and change windows qed: FW 8.42.2.0 Internal ram offsets modifications MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver Documentation: net: octeontx2: Add RVU HW and drivers overview octeontx2-pf: ethtool RSS config support octeontx2-pf: Add basic ethtool support ...

Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap

2020-01-27T21:03:00+00:00

Pull ioremap updates from Christoph Hellwig: "Remove the ioremap_nocache API (plus wrappers) that are always identical to ioremap" * tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap: remove ioremap_nocache and devm_ioremap_nocache MIPS: define ioremap_nocache to ioremap

bnxt_en: Add support for devlink info command

2020-01-27T10:33:29+00:00

Display the following information via devlink info command: - Driver name - Board id - Broad revision - Board Serial number - Board FW version - FW parameter set version - FW App version - FW management version - FW RoCE version Standard output example: $ devlink dev info pci/0000:3b:00.0 pci/0000:3b:00.0: driver bnxt_en serial_number 00-10-18-FF-FE-AD-05-00 versions: fixed: asic.id D802 asic.rev 1 running: fw 216.1.124.0 fw.psid 0.0.0 fw.app 216.1.122.0 fw.mgmt 864.0.32.0 fw.roce 216.1.15.0 [ This version has incorporated changes suggested by Jakub Kicinski to use generic devlink version tags. ] v2: Use fw.psid Cc: Jiri Pirko Cc: Jakub Kicinski Signed-off-by: Vasundhara Volam Signed-off-by: Michael Chan Signed-off-by: David S. Miller