summaryrefslogtreecommitdiffstats
path: root/doc/README.odroid
blob: 528bb952795b5ea55a68338bdf9100d8e14e4dd2 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
 U-boot for Odroid X2/U3
========================

1. Summary
==========
This is a quick instruction for setup Odroid boards based on Exynos4412.
Board config: odroid_config

2. Supported devices
====================
This U-BOOT config can be used on two boards:
- Odroid U3
- Odroid X2
with CPU Exynos 4412 rev 2.0 and 2GB of RAM

3. Boot sequence
================
iROM->BL1->(BL2 + TrustZone)->U-BOOT

This version of U-BOOT doesn't implement SPL but it is required(BL2)
and can be found in "boot.tar.gz" from here:
http://dev.odroid.com/projects/4412boot/wiki/FrontPage?action=download&value=boot.tar.gz
or here:
http://odroid.in/guides/ubuntu-lfs/boot.tar.gz

4. Boot media layout
====================
The table below shows SD/eMMC cards layout for U-boot.
The block offset is starting from 0 and the block size is 512B.
 -------------------------------------
|  Binary   | Block offset| part type |
|   name    | SD   | eMMC |(eMMC only)|
 -------------------------------------
| Bl1       | 1    | 0    |  1 (boot) |
| Bl2       | 31   | 30   |  1 (boot) |
| U-boot    | 63   | 62   |  1 (boot) |
| Tzsw      | 2111 | 2110 |  1 (boot) |
| Uboot Env | 2500 | 2500 |  0 (user) |
 -------------------------------------

5. Prepare the SD boot card - with SD card reader
=================================================
To prepare bootable media you need boot binaries provided by hardkernel.
File "boot.tar.gz" (link in point 3.) contains:
- E4412_S.bl1.HardKernel.bin
- E4412_S.tzsw.signed.bin
- bl2.signed.bin
- sd_fusing.sh
- u-boot.bin

This is all you need to boot this board. But if you want to use your custom
u-boot then you need to change u-boot.bin with your own u-boot binary*
and run the script "sd_fusing.sh" - this script is valid only for SD card.

*note:
The proper binary file of current U-boot is u-boot-dtb.bin.

quick steps for Linux:
- extract boot.tar.gz
- put any SD card into the SD reader
- check the device with "dmesg"
- run ./sd_fusing.sh /dev/sdX - where X is SD card device (but not a partition)
Check if Hardkernel U-boot is booting, and next do the same with your U-boot.

6. Prepare the eMMC boot card
   with a eMMC card reader (boot from eMMC card slot)
=====================================================
To boot the device from the eMMC slot you should use a special card reader
which supports eMMC partiion switch. All of the boot binaries are stored
on the eMMC boot partition which is normally hidden.

The "sd_fusing.sh" script can be used after updating offsets of binaries
according to the table from point 4. Be sure that you are working on the right
eMMC partition - its size is usually very small, about 1-4 MiB.

7. Prepare the eMMC boot card
   with a SD card reader (boot from SD card slot)
=================================================
If you have an eMMC->microSD adapter you can prepare the card as in point 5.
But then the device can boot only from the SD card slot.

8. Prepare the boot media using Hardkernel U-boot
=================================================
You can update the U-boot to the custom one if you have an working bootloader
delivered with the board on a eMMC/SD card. Then follow the steps:
- install the android fastboot tool
- connect a micro usb cable to the board
- on the U-boot prompt, run command: fastboot (as a root)
- on the host, run command: "fastboot flash bootloader u-boot-dtb.bin"
- the custom U-boot should start after the board resets.

9. Partition layout
====================
Default U-boot environment is setup for fixed partiion layout.

Partition table: MSDOS. Disk layout and files as listed in the table below.
 ----- ------ ------ ------ -------- ---------------------------------
| Num | Name |  FS  | Size | Offset |         Reguired files          |
|     |      | Type |  MiB |  MiB   |                                 |
 ----- ------ ------ ------ -------- ---------------------------------
|  1  | BOOT | fat  |  100 |   2    |  kernel, fdt**                  |
|  2  | ROOT | ext4 |   -  |        |  any Linux system               |
 ----- ------ ------ ------ -------- ---------------------------------

**note:
Supported fdt files are:
- exynos4412-odroidx2.dtb
- exynos4412-odroidu3.dtb

Supported kernel files are:
- Image.itb
- zImage
- uImage

The default environmental variable "dfu_alt_info" is set* for above layout.
Each partition size is just an example, dfu_alt_info tries init two partitions.
The size of each is not important.

*note:
$dfu_alt_info is set on a boot time and it is concatenated using two variables:
- $dfu_alt_boot(set dynamically)
- $dfu_alt_system(from current env).

To add any changes to dfu_alt_info - please modify $dfu_alt_system only.
Changes are visible after board reset.

10. The environment and booting the kernel
==========================================
There are three macros defined in config for various boot options:
Two for both, kernel with device tree support and also without it:
- boot_uimg - load uImage
- boot_zimg - load zImage
If proper fdt file exists then it will be automatically loaded,
so for old kernel types, please remove fdt file from boot partition.

The third boot option for multi image support (more info: doc/uImage.FIT/)
- boot_fit - for binary file: "Image.itb"

Default boot command: "autoboot"
And the boot sequence is:
- boot_fit - if "Image.itb" exists
- boot_zimg - if "zImage" exists
- boot_uimg - if "uImage" exists
OpenPOWER on IntegriCloud