summaryrefslogtreecommitdiffstats
path: root/board/sc3/init.S
blob: 097aa4a5e74882a91214416f3af5c740df47fa0c (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
/*
 * SPDX-License-Identifier:	GPL-2.0	IBM-pibs
 */
#include <config.h>
#include <asm/ppc4xx.h>

#include <ppc_asm.tmpl>
#include <ppc_defs.h>

#include <asm/cache.h>
#include <asm/mmu.h>

/**
 * ext_bus_cntlr_init - Initializes the External Bus Controller for the external peripherals
 *
 * IMPORTANT: For pass1 this code must run from cache since you can not
 * reliably change a peripheral banks timing register (pbxap) while running
 * code from that bank. For ex., since we are running from ROM on bank 0, we
 * can NOT execute the code that modifies bank 0 timings from ROM, so
 * we run it from cache.
 *
 * Bank 0 - Boot-Flash
 * Bank 1 - NAND-Flash
 * Bank 2 - ISA bus
 * Bank 3 - Second Flash
 * Bank 4 - USB controller
 */
	.globl ext_bus_cntlr_init
ext_bus_cntlr_init:
/*
 * We need the current boot up configuration to set correct
 * timings into internal flash and external flash
 */
		mfdcr r24,CPC0_PSR		/* xxxx xxxx xxxx xxx? ?xxx xxxx xxxx xxxx
						   0 0 -> 8 bit external ROM
						   0 1 -> 16 bit internal ROM */
		addi r4,0,2
		srw r24,r24,r4				/* shift right r24 two positions */
		andi. r24,r24,0x06000
/*
 * All calculations are based on 33MHz EBC clock.
 *
 * First, create a "very slow" timing (~250ns) with burst mode enabled
 * This is need for the external flash access
 */
		lis r25,0x0800
		/* 0000 1000 0xxx 0000 0000 0010 100x xxxx = 0x03800280 */
		ori r25,r25,0x0280
/*
 * Second, create a fast timing:
 * 90ns first cycle - 3 clock access
 * and 90ns burst cycle, plus 1 clock after the last access
 * This is used for the internal access
 */
		lis r26,0x8900
		/* 1000 1001 0xxx 0000 0000 0010 100x xxxx */
		ori r26,r26,0x0280
/*
 * We can't change settings on CS# if we currently use them.
 * -> load a few instructions into cache and run this code from cache
 */
		mflr r4					/* save link register */
		bl ..getAddr
..getAddr:
		mflr r3					/* get address of ..getAddr */
		mtlr r4					/* restore link register */
		addi r4,0,14				/* set ctr to 10; used to prefetch */
		mtctr r4				/* 10 cache lines to fit this function
							in cache (gives us 8x10=80 instructions) */
..ebcloop:
		icbt r0,r3				/* prefetch cache line for addr in r3 */
		addi r3,r3,32				/* move to next cache line */
		bdnz ..ebcloop				/* continue for 10 cache lines */
/*
 * Delay to ensure all accesses to ROM are complete before changing
 * bank 0 timings. 200usec should be enough.
 * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles
 */
		lis r3,0x0
		ori r3,r3,0xA000			/* ensure 200usec have passed since reset */
		mtctr r3
..spinlp:
		bdnz ..spinlp				/* spin loop */

/*-----------------------------------------------------------------------
 * Memory Bank 0 (BOOT-ROM) initialization
 * 0xFFEF00000....0xFFFFFFF
 * We only have to change the timing. Mapping is ok by boot-strapping
 *----------------------------------------------------------------------- */

		li r4,PB1AP				/* PB0AP=Peripheral Bank 0 Access Parameters */
		mtdcr EBC0_CFGADDR,r4

		mr r4,r26				/* assume internal fast flash is boot flash */
		cmpwi r24,0x2000			/* assumption true? ... */
		beq 1f					/* ...yes! */
		mr r4,r25				/* ...no, use the slow variant */
		mr r25,r26				/* use this for the other flash */
1:
		mtdcr EBC0_CFGDATA,r4			/* change timing now */

		li r4,PB0CR				/* PB0CR=Peripheral Bank 0 Control Register */
		mtdcr EBC0_CFGADDR,r4
		mfdcr r4,EBC0_CFGDATA
		lis r3,0x0001
		ori r3,r3,0x8000			/* allow reads and writes */
		or r4,r4,r3
		mtdcr EBC0_CFGDATA,r4

/*-----------------------------------------------------------------------
 * Memory Bank 3 (Second-Flash) initialization
 * 0xF0000000...0xF01FFFFF -> 2MB
 *----------------------------------------------------------------------- */

		li r4,PB3AP				/* Peripheral Bank 1 Access Parameter */
		mtdcr EBC0_CFGADDR,r4
		mtdcr EBC0_CFGDATA,r2			/* change timing */

		li r4,PB3CR				/* Peripheral Bank 1 Configuration Registers */
		mtdcr EBC0_CFGADDR,r4

		lis r4,0xF003
		ori r4,r4,0x8000
/*
 * Consider boot configuration
 */
		xori r24,r24,0x2000			/* invert current bus width */
		or r4,r4,r24
		mtdcr EBC0_CFGDATA,r4

/*-----------------------------------------------------------------------
 * Memory Bank 1 (NAND-Flash) initialization
 * 0x77D00000...0x77DFFFFF -> 1MB
 * - the write/read pulse to the NAND can be as short as 25ns, bus the cycle time is always 50ns
 * - the setup time is 0ns
 * - the hold time is 15ns
 * ->
 *   - TWT = 0
 *   - CSN = 0
 *   - OEN = 0
 *   - WBN = 0
 *   - WBF = 0
 *   - TH  = 1
 * ----> 2 clocks per cycle = 60ns cycle (30ns active, 30ns hold)
 *----------------------------------------------------------------------- */

		li r4,PB1AP				/* Peripheral Bank 1 Access Parameter */
		mtdcr EBC0_CFGADDR,r4

		lis r4,0x0000
		ori r4,r4,0x0200
		mtdcr EBC0_CFGDATA,r4

		li r4,PB1CR				/* Peripheral Bank 1 Configuration Registers */
		mtdcr EBC0_CFGADDR,r4

		lis r4,0x77D1
		ori r4,r4,0x8000
		mtdcr EBC0_CFGDATA,r4


/* USB init (without acceleration) */
#ifndef CONFIG_ISP1161_PRESENT
		li r4,PB4AP				/* PB4AP=Peripheral Bank 4 Access Parameters */
		mtdcr EBC0_CFGADDR,r4
		lis r4,0x0180
		ori r4,r4,0x5940
		mtdcr EBC0_CFGDATA,r4
#endif

/*-----------------------------------------------------------------------
 * Memory Bank 2 (ISA Access) initialization (plus memory bank 6 and 7)
 * 0x78000000...0x7BFFFFFF -> 64 MB
 * Wir arbeiten bei 33 MHz -> 30ns
 *-----------------------------------------------------------------------

 A7 (ppc notation) or A24 (standard notation) decides about
 the type of access:
 A7/A24=0 -> memory cycle
 A7/ /A24=1 -> I/O cycle
*/
		li r4,PB2AP				/* PB2AP=Peripheral Bank 2 Access Parameters */
		mtdcr EBC0_CFGADDR,r4
/*
 We emulate an ISA access

 1. Address active
 2. wait 0 EBC clocks -> CSN=0
 3. set CS#
 4. wait 0 EBC clock -> OEN/WBN=0
 5. set OE#/WE#
 6. wait 4 clocks (ca. 90ns) and for Ready signal
 7. hold for 4 clocks -> TH=4
*/

#if 1
/* faster access to isa-bus */
		lis r4,0x0180
		ori r4,r4,0x5940
#else
		lis r4,0x0100
		ori r4,r4,0x0340
#endif
		mtdcr EBC0_CFGDATA,r4

#ifdef IDE_USES_ISA_EMULATION
		li r25,PB5AP				/* PB5AP=Peripheral Bank 5 Access Parameters */
		mtdcr EBC0_CFGADDR,r25
		mtdcr EBC0_CFGDATA,r4
#endif

		li r25,PB6AP				/* PB6AP=Peripheral Bank 6 Access Parameters */
		mtdcr EBC0_CFGADDR,r25
		mtdcr EBC0_CFGDATA,r4
		li r25,PB7AP				/* PB7AP=Peripheral Bank 7 Access Parameters */
		mtdcr EBC0_CFGADDR,r25
		mtdcr EBC0_CFGDATA,r4

		li r25,PB2CR				/* PB2CR=Peripheral Bank 2 Configuration Register */
		mtdcr EBC0_CFGADDR,r25

		lis r4,0x780B
		ori r4,r4,0xA000
		mtdcr EBC0_CFGDATA,r4
/*
 * the other areas are only 1MiB in size
 */
		lis r4,0x7401
		ori r4,r4,0xA000

		li r25,PB6CR				/* PB6CR=Peripheral Bank 6 Configuration Register */
		mtdcr EBC0_CFGADDR,r25
		lis r4,0x7401
		ori r4,r4,0xA000
		mtdcr EBC0_CFGDATA,r4

		li r25,PB7CR				/* PB7CR=Peripheral Bank 7 Configuration Register */
		mtdcr EBC0_CFGADDR,r25
		lis r4,0x7411
		ori r4,r4,0xA000
		mtdcr EBC0_CFGDATA,r4

#ifndef CONFIG_ISP1161_PRESENT
		li r25,PB4CR				/* PB4CR=Peripheral Bank 4 Configuration Register */
		mtdcr EBC0_CFGADDR,r25
		lis r4,0x7421
		ori r4,r4,0xA000
		mtdcr EBC0_CFGDATA,r4
#endif
#ifdef IDE_USES_ISA_EMULATION
		li r25,PB5CR				/* PB5CR=Peripheral Bank 5 Configuration Register */
		mtdcr EBC0_CFGADDR,r25
		lis r4,0x0000
		ori r4,r4,0x0000
		mtdcr EBC0_CFGDATA,r4
#endif

/*-----------------------------------------------------------------------
 * Memory bank 4: USB controller Philips ISP6111
 * 0x77C00000 ... 0x77CFFFFF
 *
 * The chip is connected to:
 * - CPU CS#4
 * - CPU IRQ#2
 * - CPU DMA 3
 *
 * Timing:
 * - command to first data: 300ns. Software must ensure this timing!
 * - Write pulse: 26ns
 * - Read pulse: 33ns
 * - read cycle time: 150ns
 * - write cycle time: 140ns
 *
 * Note: All calculations are based on 33MHz EBC clock. One '#' or '_' is 30ns
 *
 *			  |- 300ns --|
 *		  |---- 420ns ---|---- 420ns ---| cycle
 * CS ############:###____#######:###____#######
 * OE ############:####___#######:####___#######
 * WE ############:####__########:####__########
 *
 * ----> 2 clocks RD/WR pulses: 60ns
 * ----> CSN: 3 clock, 90ns
 * ----> OEN: 1 clocks (read cycle)
 * ----> WBN: 1 clocks (write cycle)
 * ----> WBE: 2 clocks
 * ----> TH: 7 clock, 210ns
 * ----> TWT: 7 clocks
 *----------------------------------------------------------------------- */

#ifdef CONFIG_ISP1161_PRESENT

		li r4,PB4AP				/* PB4AP=Peripheral Bank 4 Access Parameters */
		mtdcr EBC0_CFGADDR,r4

		lis r4,0x030D
		ori r4,r4,0x5E80
		mtdcr EBC0_CFGDATA,r4

		li r4,PB4CR				/* PB2CR=Peripheral Bank 4 Configuration Register */
		mtdcr EBC0_CFGADDR,r4

		lis r4,0x77C1
		ori r4,r4,0xA000
		mtdcr EBC0_CFGDATA,r4

#endif

#ifndef IDE_USES_ISA_EMULATION

/*-----------------------------------------------------------------------
 * Memory Bank 5 used for IDE access
 *
 * Timings for IDE Interface
 *
 * SETUP / LENGTH / HOLD - cycles valid for 33.3 MHz clk -> 30ns cycle time
 *  70		165		30		PIO-Mode 0, [ns]
 *   3		  6		 1		[Cycles] ----> AP=0x040C0200
 *  50		125		20	   PIO-Mode 1, [ns]
 *   2		  5		 1		[Cycles] ----> AP=0x03080200
 *  30		100		15	   PIO-Mode 2, [ns]
 *   1		  4		 1		[Cycles] ----> AP=0x02040200
 *  30		 80		10	   PIO-Mode 3, [ns]
 *   1		  3		 1		[Cycles] ----> AP=0x01840200
 *  25		 70		10	   PIO-Mode 4, [ns]
 *   1		  3		 1		[Cycles] ----> AP=0x01840200
 *
 *----------------------------------------------------------------------- */

		li r4,PB5AP
		mtdcr EBC0_CFGADDR,r4
		lis r4,0x040C
		ori r4,r4,0x0200
		mtdcr EBC0_CFGDATA,r4

		li r4,PB5CR			/* PB2CR=Peripheral Bank 2 Configuration Register */
		mtdcr EBC0_CFGADDR,r4

		lis r4,0x7A01
		ori r4,r4,0xA000
		mtdcr EBC0_CFGDATA,r4
#endif
/*
 * External Peripheral Control Register
 */
		li r4,EBC0_CFG
		mtdcr EBC0_CFGADDR,r4

		lis r4,0xB84E
		ori r4,r4,0xF000
		mtdcr EBC0_CFGDATA,r4
/*
 * drive POST code
 */
		lis r4,0x7900
		ori r4,r4,0x0080
		li r3,0x0001
		stb r3,0(r4)			/* 01 -> external bus controller is initialized */
		nop				/* pass2 DCR errata #8 */
		blr
OpenPOWER on IntegriCloud