summaryrefslogtreecommitdiffstats
path: root/board/lwmon5/init.S
blob: e5207c2b40b5f1a0f26772b49dc0a76c420d39e0 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
/*
 * (C) Copyright 2007
 * Stefan Roese, DENX Software Engineering, sr@denx.de.
 *
 *  Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <asm-offsets.h>
#include <ppc_asm.tmpl>
#include <config.h>
#include <asm/mmu.h>

/**************************************************************************
 * TLB TABLE
 *
 * This table is used by the cpu boot code to setup the initial tlb
 * entries. Rather than make broad assumptions in the cpu source tree,
 * this table lets each board set things up however they like.
 *
 *  Pointer to the table is returned in r1
 *
 *************************************************************************/
	.section .bootpg,"ax"
	.globl tlbtab

tlbtab:
	tlbtab_start

	/*
	 * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
	 * speed up boot process. It is patched after relocation to enable SA_I
	 */
	tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 1, AC_RWX | SA_G)

	/*
	 * TLB entries for SDRAM are not needed on this platform.
	 * They are dynamically generated in the SPD DDR(2) detection
	 * routine.
	 */

#ifdef CONFIG_SYS_INIT_RAM_DCACHE
	/* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
	tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G)
#endif

	/* TLB-entry for PCI Memory */
	tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 1, AC_RW | SA_IG)
	tlbentry(CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 1, AC_RW | SA_IG)
	tlbentry(CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 1, AC_RW | SA_IG)
	tlbentry(CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 1, AC_RW | SA_IG)

	/* TLB-entry for the FPGA Chip select 2 */
	tlbentry(CONFIG_SYS_FPGA_BASE_0, SZ_1M, CONFIG_SYS_FPGA_BASE_0, 1, AC_RWX | SA_I|SA_G)

	/* TLB-entry for the FPGA Chip select 3 */
	tlbentry(CONFIG_SYS_FPGA_BASE_1, SZ_1M, CONFIG_SYS_FPGA_BASE_1, 1,AC_RWX | SA_I|SA_G)

	/* TLB-entry for the LIME Controller */
	tlbentry(CONFIG_SYS_LIME_BASE_0, SZ_16M, CONFIG_SYS_LIME_BASE_0, 1, AC_RWX | SA_I|SA_G)
	tlbentry(CONFIG_SYS_LIME_BASE_1, SZ_16M, CONFIG_SYS_LIME_BASE_1, 1, AC_RWX | SA_I|SA_G)
	tlbentry(CONFIG_SYS_LIME_BASE_2, SZ_16M, CONFIG_SYS_LIME_BASE_2, 1, AC_RWX | SA_I|SA_G)
	tlbentry(CONFIG_SYS_LIME_BASE_3, SZ_16M, CONFIG_SYS_LIME_BASE_3, 1, AC_RWX | SA_I|SA_G)

	/* TLB-entry for Internal Registers & OCM */
	tlbentry(0xe0000000, SZ_16M, 0xe0000000, 0,  AC_RWX | SA_I)

	/*TLB-entry PCI registers*/
	tlbentry(0xEEC00000, SZ_1K, 0xEEC00000, 1,  AC_RWX | SA_IG)

	/* TLB-entry for peripherals */
	tlbentry(0xEF000000, SZ_16M, 0xEF000000, 1, AC_RWX | SA_IG)

	tlbtab_end
OpenPOWER on IntegriCloud