1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
|
/*
* Copyright (C) 2011
* Stefan Herbrechtsmeier <stefan@code.herbrechtsmeier.net>
*
* Based on Kirkwood support:
* (C) Copyright 2009
* Marvell Semiconductor <www.marvell.com>
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <miiphy.h>
#include <netdev.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include <asm/arch/mpp.h>
#include <asm/arch/gpio.h>
#include "dns325.h"
DECLARE_GLOBAL_DATA_PTR;
int board_early_init_f(void)
{
/* Gpio configuration */
mvebu_config_gpio(DNS325_OE_VAL_LOW, DNS325_OE_VAL_HIGH,
DNS325_OE_LOW, DNS325_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
MPP3_NF_IO5,
MPP4_NF_IO6,
MPP5_NF_IO7,
MPP6_SYSRST_OUTn,
MPP7_GPO,
MPP8_TW_SDA,
MPP9_TW_SCK,
MPP10_UART0_TXD,
MPP11_UART0_RXD,
MPP12_SD_CLK,
MPP13_SD_CMD,
MPP14_SD_D0,
MPP15_SD_D1,
MPP16_SD_D2,
MPP17_SD_D3,
MPP18_NF_IO0,
MPP19_NF_IO1,
MPP20_SATA1_ACTn, /* sata1(left) status led */
MPP21_SATA0_ACTn, /* sata0(right) status led */
MPP22_GPIO,
MPP23_GPIO,
MPP24_GPIO, /* power off out */
MPP25_GPIO,
MPP26_GPIO, /* power led */
MPP27_GPIO, /* sata0(right) error led */
MPP28_GPIO, /* sata1(left) error led */
MPP29_GPIO, /* usb error led */
MPP30_GPIO,
MPP31_GPIO,
MPP32_GPIO,
MPP33_GPIO,
MPP34_GPIO, /* power key */
MPP35_GPIO,
MPP36_GPIO,
MPP37_GPIO,
MPP38_GPIO,
MPP39_GPIO, /* enable sata 0 */
MPP40_GPIO, /* enable sata 1 */
MPP41_GPIO, /* hdd0 present */
MPP42_GPIO, /* hdd1 present */
MPP43_GPIO, /* usb status led */
MPP44_GPIO, /* fan status */
MPP45_GPIO, /* fan high speed */
MPP46_GPIO, /* fan low speed */
MPP47_GPIO, /* usb umount */
MPP48_GPIO, /* factory reset */
MPP49_GPIO, /* thermal sensor */
0
};
kirkwood_mpp_conf(kwmpp_config, NULL);
kw_gpio_set_blink(DNS325_GPIO_LED_POWER , 1);
kw_gpio_set_value(DNS325_GPIO_SATA0_EN , 1);
return 0;
}
int board_init(void)
{
/* Boot parameters address */
gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
return 0;
}
#ifdef CONFIG_RESET_PHY_R
/* Configure and initialize PHY */
void reset_phy(void)
{
u16 reg;
u16 devadr;
char *name = "egiga0";
if (miiphy_set_current_dev(name))
return;
/* command to read PHY dev address */
if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
printf("Err..(%s) could not read PHY dev address\n", __func__);
return;
}
/*
* Enable RGMII delay on Tx and Rx for CPU port
* Ref: sec 4.7.2 of chip datasheet
*/
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
/* reset the phy */
miiphy_reset(name, devadr);
debug("88E1116 Initialized on %s\n", name);
}
#endif /* CONFIG_RESET_PHY_R */
|
