/* * linux/include/linux/mtd/nand.h * * Copyright (c) 2000 David Woodhouse * Steven J. Hill * Thomas Gleixner * * $Id: nand.h,v 1.68 2004/11/12 10:40:37 gleixner Exp $ * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. * * Info: * Contains standard defines and IDs for NAND flash devices * * Changelog: * 01-31-2000 DMW Created * 09-18-2000 SJH Moved structure out of the Disk-On-Chip drivers * so it can be used by other NAND flash device * drivers. I also changed the copyright since none * of the original contents of this file are specific * to DoC devices. David can whack me with a baseball * bat later if I did something naughty. * 10-11-2000 SJH Added private NAND flash structure for driver * 10-24-2000 SJH Added prototype for 'nand_scan' function * 10-29-2001 TG changed nand_chip structure to support * hardwarespecific function for accessing control lines * 02-21-2002 TG added support for different read/write adress and * ready/busy line access function * 02-26-2002 TG added chip_delay to nand_chip structure to optimize * command delay times for different chips * 04-28-2002 TG OOB config defines moved from nand.c to avoid duplicate * defines in jffs2/wbuf.c * 08-07-2002 TG forced bad block location to byte 5 of OOB, even if * CONFIG_MTD_NAND_ECC_JFFS2 is not set * 08-10-2002 TG extensions to nand_chip structure to support HW-ECC * * 08-29-2002 tglx nand_chip structure: data_poi for selecting * internal / fs-driver buffer * support for 6byte/512byte hardware ECC * read_ecc, write_ecc extended for different oob-layout * oob layout selections: NAND_NONE_OOB, NAND_JFFS2_OOB, * NAND_YAFFS_OOB * 11-25-2002 tglx Added Manufacturer code FUJITSU, NATIONAL * Split manufacturer and device ID structures * * 02-08-2004 tglx added option field to nand structure for chip anomalities * 05-25-2004 tglx added bad block table support, ST-MICRO manufacturer id * update of nand_chip structure description */ #ifndef __LINUX_MTD_NAND_NEW_H #define __LINUX_MTD_NAND_NEW_H #include #include struct mtd_info; /* Scan and identify a NAND device */ extern int nand_scan (struct mtd_info *mtd, int max_chips); /* Free resources held by the NAND device */ extern void nand_release (struct mtd_info *mtd); /* Read raw data from the device without ECC */ extern int nand_read_raw (struct mtd_info *mtd, uint8_t *buf, loff_t from, size_t len, size_t ooblen); /* This constant declares the max. oobsize / page, which * is supported now. If you add a chip with bigger oobsize/page * adjust this accordingly. */ #define NAND_MAX_OOBSIZE 64 /* * Constants for hardware specific CLE/ALE/NCE function */ /* Select the chip by setting nCE to low */ #define NAND_CTL_SETNCE 1 /* Deselect the chip by setting nCE to high */ #define NAND_CTL_CLRNCE 2 /* Select the command latch by setting CLE to high */ #define NAND_CTL_SETCLE 3 /* Deselect the command latch by setting CLE to low */ #define NAND_CTL_CLRCLE 4 /* Select the address latch by setting ALE to high */ #define NAND_CTL_SETALE 5 /* Deselect the address latch by setting ALE to low */ #define NAND_CTL_CLRALE 6 /* Set write protection by setting WP to high. Not used! */ #define NAND_CTL_SETWP 7 /* Clear write protection by setting WP to low. Not used! */ #define NAND_CTL_CLRWP 8 /* * Standard NAND flash commands */ #define NAND_CMD_READ0 0 #define NAND_CMD_READ1 1 #define NAND_CMD_PAGEPROG 0x10 #define NAND_CMD_READOOB 0x50 #define NAND_CMD_ERASE1 0x60 #define NAND_CMD_STATUS 0x70 #define NAND_CMD_STATUS_MULTI 0x71 #define NAND_CMD_SEQIN 0x80 #define NAND_CMD_READID 0x90 #define NAND_CMD_ERASE2 0xd0 #define NAND_CMD_RESET 0xff /* Extended commands for large page devices */ #define NAND_CMD_READSTART 0x30 #define NAND_CMD_CACHEDPROG 0x15 /* Status bits */ #define NAND_STATUS_FAIL 0x01 #define NAND_STATUS_FAIL_N1 0x02 #define NAND_STATUS_TRUE_READY 0x20 #define NAND_STATUS_READY 0x40 #define NAND_STATUS_WP 0x80 /* * Constants for ECC_MODES */ /* No ECC. Usage is not recommended ! */ #define NAND_ECC_NONE 0 /* Software ECC 3 byte ECC per 256 Byte data */ #define NAND_ECC_SOFT 1 /* Hardware ECC 3 byte ECC per 256 Byte data */ #define NAND_ECC_HW3_256 2 /* Hardware ECC 3 byte ECC per 512 Byte data */ #define NAND_ECC_HW3_512 3 /* Hardware ECC 3 byte ECC per 512 Byte data */ #define NAND_ECC_HW6_512 4 /* Hardware ECC 8 byte ECC per 512 Byte data */ #define NAND_ECC_HW8_512 6 /* Hardware ECC 12 byte ECC per 2048 Byte data */ #define NAND_ECC_HW12_2048 7 /* * Constants for Hardware ECC */ /* Reset Hardware ECC for read */ #define NAND_ECC_READ 0 /* Reset Hardware ECC for write */ #define NAND_ECC_WRITE 1 /* Enable Hardware ECC before syndrom is read back from flash */ #define NAND_ECC_READSYN 2 /* Option constants for bizarre disfunctionality and real * features */ /* Chip can not auto increment pages */ #define NAND_NO_AUTOINCR 0x00000001 /* Buswitdh is 16 bit */ #define NAND_BUSWIDTH_16 0x00000002 /* Device supports partial programming without padding */ #define NAND_NO_PADDING 0x00000004 /* Chip has cache program function */ #define NAND_CACHEPRG 0x00000008 /* Chip has copy back function */ #define NAND_COPYBACK 0x00000010 /* AND Chip which has 4 banks and a confusing page / block * assignment. See Renesas datasheet for further information */ #define NAND_IS_AND 0x00000020 /* Chip has a array of 4 pages which can be read without * additional ready /busy waits */ #define NAND_4PAGE_ARRAY 0x00000040 /* Options valid for Samsung large page devices */ #define NAND_SAMSUNG_LP_OPTIONS \ (NAND_NO_PADDING | NAND_CACHEPRG | NAND_COPYBACK) /* Macros to identify the above */ #define NAND_CANAUTOINCR(chip) (!(chip->options & NAND_NO_AUTOINCR)) #define NAND_MUST_PAD(chip) (!(chip->options & NAND_NO_PADDING)) #define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG)) #define NAND_HAS_COPYBACK(chip) ((chip->options & NAND_COPYBACK)) /* Mask to zero out the chip options, which come from the id table */ #define NAND_CHIPOPTIONS_MSK (0x0000ffff & ~NAND_NO_AUTOINCR) /* Non chip related options */ /* Use a flash based bad block table. This option is passed to the * default bad block table function. */ #define NAND_USE_FLASH_BBT 0x00010000 /* The hw ecc generator provides a syndrome instead a ecc value on read * This can only work if we have the ecc bytes directly behind the * data bytes. Applies for DOC and AG-AND Renesas HW Reed Solomon generators */ #define NAND_HWECC_SYNDROME 0x00020000 /* Options set by nand scan */ /* Nand scan has allocated oob_buf */ #define NAND_OOBBUF_ALLOC 0x40000000 /* Nand scan has allocated data_buf */ #define NAND_DATABUF_ALLOC 0x80000000 /* * nand_state_t - chip states * Enumeration for NAND flash chip state */ typedef enum { FL_READY, FL_READING, FL_WRITING, FL_ERASING, FL_SYNCING, FL_CACHEDPRG, } nand_state_t; /* Keep gcc happy */ struct nand_chip; #if 0 /** * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independend devices * @lock: protection lock * @active: the mtd device which holds the controller currently */ struct nand_hw_control { spinlock_t lock; struct nand_chip *active; }; #endif /** * struct nand_chip - NAND Private Flash Chip Data * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the flash device * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the flash device * @read_byte: [REPLACEABLE] read one byte from the chip * @write_byte: [REPLACEABLE] write one byte to the chip * @read_word: [REPLACEABLE] read one word from the chip * @write_word: [REPLACEABLE] write one word to the chip * @write_buf: [REPLACEABLE] write data from the buffer to the chip * @read_buf: [REPLACEABLE] read data from the chip into the buffer * @verify_buf: [REPLACEABLE] verify buffer contents against the chip data * @select_chip: [REPLACEABLE] select chip nr * @block_bad: [REPLACEABLE] check, if the block is bad * @block_markbad: [REPLACEABLE] mark the block bad * @hwcontrol: [BOARDSPECIFIC] hardwarespecific function for accesing control-lines * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accesing device ready/busy line * If set to NULL no access to ready/busy is available and the ready/busy information * is read from the chip status register * @cmdfunc: [REPLACEABLE] hardwarespecific function for writing commands to the chip * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on ready * @calculate_ecc: [REPLACEABLE] function for ecc calculation or readback from ecc hardware * @correct_data: [REPLACEABLE] function for ecc correction, matching to ecc generator (sw/hw) * @enable_hwecc: [BOARDSPECIFIC] function to enable (reset) hardware ecc generator. Must only * be provided if a hardware ECC is available * @erase_cmd: [INTERN] erase command write function, selectable due to AND support * @scan_bbt: [REPLACEABLE] function to scan bad block table * @eccmode: [BOARDSPECIFIC] mode of ecc, see defines * @eccsize: [INTERN] databytes used per ecc-calculation * @eccbytes: [INTERN] number of ecc bytes per ecc-calculation step * @eccsteps: [INTERN] number of ecc calculation steps per page * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transfering data from array to read regs (tR) * @chip_lock: [INTERN] spinlock used to protect access to this structure and the chip * @wq: [INTERN] wait queue to sleep on if a NAND operation is in progress * @state: [INTERN] the current state of the NAND device * @page_shift: [INTERN] number of address bits in a page (column address bits) * @phys_erase_shift: [INTERN] number of address bits in a physical eraseblock * @bbt_erase_shift: [INTERN] number of address bits in a bbt entry * @chip_shift: [INTERN] number of address bits in one chip * @data_buf: [INTERN] internal buffer for one page + oob * @oob_buf: [INTERN] oob buffer for one eraseblock * @oobdirty: [INTERN] indicates that oob_buf must be reinitialized * @data_poi: [INTERN] pointer to a data buffer * @options: [BOARDSPECIFIC] various chip options. They can partly be set to inform nand_scan about * special functionality. See the defines for further explanation * @badblockpos: [INTERN] position of the bad block marker in the oob area * @numchips: [INTERN] number of physical chips * @chipsize: [INTERN] the size of one chip for multichip arrays * @pagemask: [INTERN] page number mask = number of (pages / chip) - 1 * @pagebuf: [INTERN] holds the pagenumber which is currently in data_buf * @autooob: [REPLACEABLE] the default (auto)placement scheme * @bbt: [INTERN] bad block table pointer * @bbt_td: [REPLACEABLE] bad block table descriptor for flash lookup * @bbt_md: [REPLACEABLE] bad block table mirror descriptor * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial bad block scan * @controller: [OPTIONAL] a pointer to a hardware controller structure which is shared among multiple independend devices * @priv: [OPTIONAL] pointer to private chip date */ struct nand_chip { void __iomem *IO_ADDR_R; void __iomem *IO_ADDR_W; u_char (*read_byte)(struct mtd_info *mtd); void (*write_byte)(struct mtd_info *mtd, u_char byte); u16 (*read_word)(struct mtd_info *mtd); void (*write_word)(struct mtd_info *mtd, u16 word); void (*write_buf)(struct mtd_info *mtd, const u_char *buf, int len); void (*read_buf)(struct mtd_info *mtd, u_char *buf, int len); int (*verify_buf)(struct mtd_info *mtd, const u_char *buf, int len); void (*select_chip)(struct mtd_info *mtd, int chip); int (*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip); int (*block_markbad)(struct mtd_info *mtd, loff_t ofs); void (*hwcontrol)(struct mtd_info *mtd, int cmd); int (*dev_ready)(struct mtd_info *mtd); void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, int page_addr); int (*waitfunc)(struct mtd_info *mtd, struct nand_chip *this, int state); int (*calculate_ecc)(struct mtd_info *mtd, const u_char *dat, u_char *ecc_code); int (*correct_data)(struct mtd_info *mtd, u_char *dat, u_char *read_ecc, u_char *calc_ecc); void (*enable_hwecc)(struct mtd_info *mtd, int mode); void (*erase_cmd)(struct mtd_info *mtd, int page); int (*scan_bbt)(struct mtd_info *mtd); int eccmode; int eccsize; int eccbytes; int eccsteps; int chip_delay; #if 0 spinlock_t chip_lock; wait_queue_head_t wq; nand_state_t state; #endif int page_shift; int phys_erase_shift; int bbt_erase_shift; int chip_shift; u_char *data_buf; u_char *oob_buf; int oobdirty; u_char *data_poi; unsigned int options; int badblockpos; int numchips; unsigned long chipsize; int pagemask; int pagebuf; struct nand_oobinfo *autooob; uint8_t *bbt; struct nand_bbt_descr *bbt_td; struct nand_bbt_descr *bbt_md; struct nand_bbt_descr *badblock_pattern; struct nand_hw_control *controller; void *priv; }; /* * NAND Flash Manufacturer ID Codes */ #define NAND_MFR_TOSHIBA 0x98 #define NAND_MFR_SAMSUNG 0xec #define NAND_MFR_FUJITSU 0x04 #define NAND_MFR_NATIONAL 0x8f #define NAND_MFR_RENESAS 0x07 #define NAND_MFR_STMICRO 0x20 /** * struct nand_flash_dev - NAND Flash Device ID Structure * * @name: Identify the device type * @id: device ID code * @pagesize: Pagesize in bytes. Either 256 or 512 or 0 * If the pagesize is 0, then the real pagesize * and the eraseize are determined from the * extended id bytes in the chip * @erasesize: Size of an erase block in the flash device. * @chipsize: Total chipsize in Mega Bytes * @options: Bitfield to store chip relevant options */ struct nand_flash_dev { char *name; int id; unsigned long pagesize; unsigned long chipsize; unsigned long erasesize; unsigned long options; }; /** * struct nand_manufacturers - NAND Flash Manufacturer ID Structure * @name: Manufacturer name * @id: manufacturer ID code of device. */ struct nand_manufacturers { int id; char * name; }; extern struct nand_flash_dev nand_flash_ids[]; extern struct nand_manufacturers nand_manuf_ids[]; /** * struct nand_bbt_descr - bad block table descriptor * @options: options for this descriptor * @pages: the page(s) where we find the bbt, used with option BBT_ABSPAGE * when bbt is searched, then we store the found bbts pages here. * Its an array and supports up to 8 chips now * @offs: offset of the pattern in the oob area of the page * @veroffs: offset of the bbt version counter in the oob are of the page * @version: version read from the bbt page during scan * @len: length of the pattern, if 0 no pattern check is performed * @maxblocks: maximum number of blocks to search for a bbt. This number of * blocks is reserved at the end of the device where the tables are * written. * @reserved_block_code: if non-0, this pattern denotes a reserved (rather than * bad) block in the stored bbt * @pattern: pattern to identify bad block table or factory marked good / * bad blocks, can be NULL, if len = 0 * * Descriptor for the bad block table marker and the descriptor for the * pattern which identifies good and bad blocks. The assumption is made * that the pattern and the version count are always located in the oob area * of the first block. */ struct nand_bbt_descr { int options; int pages[NAND_MAX_CHIPS]; int offs; int veroffs; uint8_t version[NAND_MAX_CHIPS]; int len; int maxblocks; int reserved_block_code; uint8_t *pattern; }; /* Options for the bad block table descriptors */ /* The number of bits used per block in the bbt on the device */ #define NAND_BBT_NRBITS_MSK 0x0000000F #define NAND_BBT_1BIT 0x00000001 #define NAND_BBT_2BIT 0x00000002 #define NAND_BBT_4BIT 0x00000004 #define NAND_BBT_8BIT 0x00000008 /* The bad block table is in the last good block of the device */ #define NAND_BBT_LASTBLOCK 0x00000010 /* The bbt is at the given page, else we must scan for the bbt */ #define NAND_BBT_ABSPAGE 0x00000020 /* The bbt is at the given page, else we must scan for the bbt */ #define NAND_BBT_SEARCH 0x00000040 /* bbt is stored per chip on multichip devices */ #define NAND_BBT_PERCHIP 0x00000080 /* bbt has a version counter at offset veroffs */ #define NAND_BBT_VERSION 0x00000100 /* Create a bbt if none axists */ #define NAND_BBT_CREATE 0x00000200 /* Search good / bad pattern through all pages of a block */ #define NAND_BBT_SCANALLPAGES 0x00000400 /* Scan block empty during good / bad block scan */ #define NAND_BBT_SCANEMPTY 0x00000800 /* Write bbt if neccecary */ #define NAND_BBT_WRITE 0x00001000 /* Read and write back block contents when writing bbt */ #define NAND_BBT_SAVECONTENT 0x00002000 /* Search good / bad pattern on the first and the second page */ #define NAND_BBT_SCAN2NDPAGE 0x00004000 /* The maximum number of blocks to scan for a bbt */ #define NAND_BBT_SCAN_MAXBLOCKS 4 extern int nand_scan_bbt (struct mtd_info *mtd, struct nand_bbt_descr *bd); extern int nand_update_bbt (struct mtd_info *mtd, loff_t offs); extern int nand_default_bbt (struct mtd_info *mtd); extern int nand_isbad_bbt (struct mtd_info *mtd, loff_t offs, int allowbbt); extern int nand_erase_nand (struct mtd_info *mtd, struct erase_info *instr, int allowbbt); /* * Constants for oob configuration */ #define NAND_SMALL_BADBLOCK_POS 5 #define NAND_LARGE_BADBLOCK_POS 0 #endif /* __LINUX_MTD_NAND_NEW_H */