/* * (C) Copyright 2007 * Heiko Schocher, DENX Software Engineering, hs@denx.de. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * board/config.h - configuration options, board specific */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_MPC866 1 /* This is a MPC866 CPU */ #define CONFIG_MGSUVD 1 /* ...on a mgsuvd board */ /* Do boardspecific init */ #define CONFIG_BOARD_EARLY_INIT_R 1 #define CONFIG_8xx_GCLK_FREQ 66000000 #define CONFIG_SYS_SMC_UCODE_PATCH 1 /* Relocate SMC1 */ #define CONFIG_SYS_SMC_DPMEM_OFFSET 0x1fc0 #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ #define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ #define CONFIG_BOOTCOUNT_LIMIT #define CONFIG_SYS_CPM_BOOTCOUNT_ADDR 0x1eb0 /* In case of SMC relocation, the * default value is not working */ #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #define CONFIG_BOARD_TYPES 1 /* support board types */ #define CONFIG_PREBOOT "echo;" \ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ "echo" #undef CONFIG_BOOTARGS #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "addcons=setenv bootargs ${bootargs} console=ttyCPM0,${baudrate}\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "addip=setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ ":${hostname}:${netdev}:off panic=1\0" \ "flash_nfs=run nfsargs addip;" \ "bootm ${kernel_addr}\0" \ "flash_self=run ramargs addip;" \ "bootm ${kernel_addr} ${ramdisk_addr}\0" \ "net_nfs=tftp ${kernel_addr} ${bootfile}; " \ "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip addcons;" \ "bootm ${kernel_addr} - ${fdt_addr}\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/mgsuvd/uImage\0" \ "fdt_addr=400000\0" \ "kernel_addr=200000\0" \ "fdt_file=/tftpboot/mgsuvd/mgsuvd.dtb\0" \ "load=tftp 200000 ${u-boot}\0" \ "update=protect off f0000000 +${filesize};" \ "erase f0000000 +${filesize};" \ "cp.b 200000 f0000000 ${filesize};" \ "protect on f0000000 +${filesize}\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_BOOTFILESIZE #undef CONFIG_RTC_MPC8xx /* MPC866 does not support RTC */ #define CONFIG_TIMESTAMP /* but print image timestmps */ /* * Command line configuration. */ #include #define CONFIG_CMD_ASKENV #define CONFIG_CMD_DHCP #define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_I2C #define CONFIG_CMD_NFS #define CONFIG_CMD_PING /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ #ifdef CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #define CONFIG_HUSH_INIT_VAR 1 #endif #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ /*----------------------------------------------------------------------- * Internal Memory Mapped Register */ #define CONFIG_SYS_IMMR 0xFFF00000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR #define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ #define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0xf0000000 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_FLASH_SIZE 32 #define CONFIG_SYS_FLASH_CFI #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */ #define CONFIG_ENV_SIZE 0x08000 /* Total Size of Environment Sector */ #define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) /*----------------------------------------------------------------------- * Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ #endif /*----------------------------------------------------------------------- * SYPCR - System Protection Control 11-9 * SYPCR can only be written once after reset! *----------------------------------------------------------------------- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze */ #define CONFIG_SYS_SYPCR 0xffffff89 /*----------------------------------------------------------------------- * SIUMCR - SIU Module Configuration 11-6 *----------------------------------------------------------------------- */ #define CONFIG_SYS_SIUMCR 0x00610480 /*----------------------------------------------------------------------- * TBSCR - Time Base Status and Control 11-26 *----------------------------------------------------------------------- * Clear Reference Interrupt Status, Timebase freezing enabled */ #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control 11-31 *----------------------------------------------------------------------- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled */ #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) /*----------------------------------------------------------------------- * SCCR - System Clock and reset Control Register 15-27 *----------------------------------------------------------------------- * Set clock output, timebase and RTC source and divider, * power management and some other internal clocks */ #define SCCR_MASK 0x01800000 #define CONFIG_SYS_SCCR 0x01800000 #define CONFIG_SYS_DER 0 /* * Init Memory Controller: * * BR0/1 and OR0/1 (FLASH) */ #define FLASH_BASE0_PRELIM 0xf0000000 /* FLASH bank #0 */ /* used to re-map FLASH both when starting from SRAM or FLASH: * restrict access enough to keep SRAM working (if any) * but not too much to meddle with FLASH accesses */ #define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ #define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ /* * FLASH timing: Default value of OR0 after reset */ #define CONFIG_SYS_OR0_PRELIM 0xfe000954 #define CONFIG_SYS_BR0_PRELIM 0xf0000401 /* * BR1 and OR1 (SDRAM) * */ #define SDRAM_BASE1_PRELIM 0x00000000 /* SDRAM bank #0 */ #define SDRAM_MAX_SIZE (64 << 20) /* max 64 MB per bank */ /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ #define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00 #define CONFIG_SYS_OR1_PRELIM 0xfc000800 #define CONFIG_SYS_BR1_PRELIM (0x000000C0 | 0x01) #define CONFIG_SYS_MPTPR 0x0200 /* PTB=16, AMB=001, FIXME 1 RAS precharge cycles, 1 READ loop cycle (not used), 1 Write loop Cycle (not used), 1 Timer Loop Cycle */ #define CONFIG_SYS_MBMR 0x10964111 #define CONFIG_SYS_MAR 0x00000088 /* * 4096 Rows from SDRAM example configuration * 1000 factor s -> ms * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration * 4 Number of refresh cycles per period * 64 Refresh cycle in ms per number of rows */ #define CONFIG_SYS_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64)) /* GPIO/PIGGY on CS3 initialization values */ #define CONFIG_SYS_PIGGY_BASE (0x30000000) #define CONFIG_SYS_OR3_PRELIM (0xfe000d24) #define CONFIG_SYS_BR3_PRELIM (0x30000401) /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #define CONFIG_SCC3_ENET #define CONFIG_ETHPRIME "SCC ETHERNET" #define CONFIG_HAS_ETH0 /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 #define OF_STDOUT_PATH "/soc/cpm/serial@a80" /* enable I2C and select the hardware/software driver */ #undef CONFIG_HARD_I2C /* I2C with hardware support */ #define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ #define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F #define I2C_SOFT_DECLARATIONS /* * Software (bit-bang) I2C driver configuration */ #define I2C_BASE_DIR ((u16 *)(CONFIG_SYS_PIGGY_BASE + 0x04)) #define I2C_BASE_PORT ((u8 *)(CONFIG_SYS_PIGGY_BASE + 0x09)) #define SDA_BIT 0x40 #define SCL_BIT 0x80 #define SDA_CONF 0x1000 #define SCL_CONF 0x2000 #define I2C_ACTIVE do {} while (0) #define I2C_TRISTATE do {} while (0) #define I2C_READ ((in_8(I2C_BASE_PORT) & SDA_BIT) == SDA_BIT) #define I2C_SDA(bit) if(bit) { \ clrbits(be16, I2C_BASE_DIR, SDA_CONF); \ } else { \ clrbits(8, I2C_BASE_PORT, SDA_BIT); \ setbits(be16, I2C_BASE_DIR, SDA_CONF); \ } #define I2C_SCL(bit) if(bit) { \ clrbits(be16, I2C_BASE_DIR, SCL_CONF); \ } else { \ clrbits(8, I2C_BASE_PORT, SCL_BIT); \ setbits(be16, I2C_BASE_DIR, SCL_CONF); \ } #define I2C_DELAY udelay(50) /* 1/4 I2C clock duration */ #define CONFIG_I2C_MULTI_BUS 1 #define CONFIG_I2C_CMD_TREE 1 #define CONFIG_SYS_MAX_I2C_BUS 2 #define CONFIG_SYS_I2C_INIT_BOARD 1 #define CONFIG_I2C_MUX 1 /* EEprom support */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 #define CONFIG_SYS_I2C_MULTI_EEPROMS 1 #define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* Support the IVM EEprom */ #define CONFIG_SYS_IVM_EEPROM_ADR 0x50 #define CONFIG_SYS_IVM_EEPROM_MAX_LEN 0x400 #define CONFIG_SYS_IVM_EEPROM_PAGE_LEN 0x100 /* I2C SYSMON (LM75, AD7414 is almost compatible) */ #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ #define CONFIG_DTT_SENSORS {0, 2, 4, 6} /* Sensor addresses */ #define CONFIG_SYS_DTT_MAX_TEMP 70 #define CONFIG_SYS_DTT_LOW_TEMP -30 #define CONFIG_SYS_DTT_HYSTERESIS 3 #define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS) #endif /* __CONFIG_H */