/* * (C) Copyright 2006-2008 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * SPDX-License-Identifier: GPL-2.0+ */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_MPC5200 #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ #define CONFIG_MCC200 1 /* ... on MCC200 board */ /* * Valid values for CONFIG_SYS_TEXT_BASE are: * 0xFC000000 boot low (standard configuration) * 0xFFF00000 boot high * 0x00100000 boot from RAM (for testing only) */ #ifndef CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_TEXT_BASE 0xFC000000 #endif #define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33MHz */ #define CONFIG_MISC_INIT_R #define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* * Serial console configuration * * To select console on the one of 8 external UARTs, * define CONFIG_QUART_CONSOLE as 1, 2, 3, or 4 for the first Quad UART, * or as 5, 6, 7, or 8 for the second Quad UART. * COM11, COM12, COM13, COM14 are located on the second Quad UART. * * CONFIG_PSC_CONSOLE must be undefined in this case. */ #if !defined(CONFIG_PRS200) /* MCC200 configuration: */ #ifdef CONFIG_CONSOLE_COM12 #define CONFIG_QUART_CONSOLE 6 /* console is on UARTF of QUART2 */ #else #define CONFIG_QUART_CONSOLE 8 /* console is on UARTH of QUART2 */ #endif #else /* PRS200 configuration: */ #undef CONFIG_QUART_CONSOLE #endif /* CONFIG_PRS200 */ /* * To select console on PSC1, define CONFIG_PSC_CONSOLE as 1 * and undefine CONFIG_QUART_CONSOLE. */ #if !defined(CONFIG_PRS200) /* MCC200 configuration: */ #define CONFIG_PSC_CONSOLE 1 /* PSC1 may be COM */ #define CONFIG_PSC_CONSOLE2 2 /* PSC2 is PSoC */ #else /* PRS200 configuration: */ #define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ #endif #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } #define CONFIG_MII 1 #define CONFIG_DOS_PARTITION /* USB */ #define CONFIG_USB_OHCI #define CONFIG_USB_STORAGE /* automatic software updates (see board/mcc200/auto_update.c) */ #define CONFIG_AUTO_UPDATE 1 /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include #define CONFIG_CMD_BEDBUG #define CONFIG_CMD_FAT #define CONFIG_CMD_I2C #define CONFIG_CMD_USB #undef CONFIG_CMD_NET #undef CONFIG_CMD_NFS /* * Autobooting */ #define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */ #define CONFIG_PREBOOT "echo;" \ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ "echo" #undef CONFIG_BOOTARGS #ifdef CONFIG_PRS200 # define CONFIG_SYS__BOARDNAME "prs200" # define CONFIG_SYS__LINUX_CONSOLE "ttyS0" #else # define CONFIG_SYS__BOARDNAME "mcc200" # define CONFIG_SYS__LINUX_CONSOLE "ttyEU5" #endif /* Network */ #define CONFIG_ETHADDR 00:17:17:ff:00:00 #define CONFIG_IPADDR 10.76.9.29 #define CONFIG_SERVERIP 10.76.9.1 #include /* For U-Boot version */ #define CONFIG_EXTRA_ENV_SETTINGS \ "ubootver=" U_BOOT_VERSION "\0" \ "netdev=eth0\0" \ "hostname=" CONFIG_SYS__BOARDNAME "\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/mtdblock2 " \ "rootfstype=cramfs\0" \ "addip=setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ ":${hostname}:${netdev}:off panic=1\0" \ "addcons=setenv bootargs ${bootargs} " \ "console=${console},${baudrate} " \ "ubootver=${ubootver} board=${board}\0" \ "flash_nfs=run nfsargs addip addcons;" \ "bootm ${kernel_addr}\0" \ "flash_self=run ramargs addip addcons;" \ "bootm ${kernel_addr} ${ramdisk_addr}\0" \ "net_nfs=tftp 200000 ${bootfile};" \ "run nfsargs addip addcons;bootm\0" \ "console=" CONFIG_SYS__LINUX_CONSOLE "\0" \ "rootpath=/opt/eldk/ppc_6xx\0" \ "bootfile=/tftpboot/" CONFIG_SYS__BOARDNAME "/uImage\0" \ "load=tftp 200000 /tftpboot/" CONFIG_SYS__BOARDNAME "/u-boot.bin\0" \ "text_base=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ "kernel_addr=0xFC0C0000\0" \ "update=protect off ${text_base} +${filesize};" \ "era ${text_base} +${filesize};" \ "cp.b 200000 ${text_base} ${filesize}\0" \ "unlock=yes\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" #define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */ /* * IPB Bus clocking configuration. */ #define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* * I2C configuration */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ #define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ #define CONFIG_SYS_I2C_SLAVE 0x7F /* * Flash configuration (8,16 or 32 MB) * TEXT base always at 0xFFF00000 * ENV_ADDR always at 0xFFF40000 * FLASH_BASE at 0xFC000000 for 64 MB (only 32MB are supported, not enough addr lines!!!) * 0xFE000000 for 32 MB * 0xFF000000 for 16 MB * 0xFF800000 for 8 MB */ #define CONFIG_SYS_FLASH_BASE 0xfc000000 #define CONFIG_SYS_FLASH_SIZE 0x04000000 #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CONFIG_SYS_FLASH_PROTECTION 1 /* hardware flash protection */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ #define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) #define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */ #if CONFIG_SYS_TEXT_BASE == CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_LOWBOOT 1 #endif /* * Memory map */ #define CONFIG_SYS_MBAR 0xf0000000 #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_DEFAULT_MBAR 0x80000000 /* Use SRAM until RAM will be available */ #define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM #define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) # define CONFIG_SYS_RAMBOOT 1 #endif #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Ethernet configuration */ /* #define CONFIG_MPC5xxx_FEC 1 */ /* #define CONFIG_MPC5xxx_FEC_MII100 */ /* * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb */ /* #define CONFIG_MPC5xxx_FEC_MII10 */ #define CONFIG_PHY_ADDR 1 /* * LCD Splash Screen */ #if !defined(CONFIG_PRS200) #define CONFIG_LCD 1 #define CONFIG_PROGRESSBAR 1 #endif #if defined(CONFIG_LCD) #define CONFIG_SPLASH_SCREEN 1 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 #define LCD_BPP LCD_MONOCHROME #endif /* * GPIO configuration */ /* 0x10000004 = 32MB SDRAM */ /* 0x90000004 = 64MB SDRAM */ #if defined(CONFIG_LCD) /* set PSC2 in UART mode */ #define CONFIG_SYS_GPS_PORT_CONFIG 0x00000044 #else #define CONFIG_SYS_GPS_PORT_CONFIG 0x00000004 #endif /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ #if defined(CONFIG_CMD_KGDB) # define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /* * Various low-level settings */ #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI #define CONFIG_SYS_HID0_FINAL HID0_ICE #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE #define CONFIG_SYS_BOOTCS_CFG 0x0004fb00 #define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE /* Quad UART @0x80000000 (MBAR is relocated to 0xF0000000) */ #define CONFIG_SYS_CS2_START 0x80000000 #define CONFIG_SYS_CS2_SIZE 0x00001000 #define CONFIG_SYS_CS2_CFG 0x1d300 /* Second Quad UART @0x80010000 */ #define CONFIG_SYS_CS1_START 0x80010000 #define CONFIG_SYS_CS1_SIZE 0x00001000 #define CONFIG_SYS_CS1_CFG 0x1d300 /* Leica - build revision resistors */ /* #define CONFIG_SYS_CS3_START 0x80020000 #define CONFIG_SYS_CS3_SIZE 0x00000004 #define CONFIG_SYS_CS3_CFG 0x1d300 */ /* * Select one of quarts as a default * console. If undefined - PSC console * wil be default */ #define CONFIG_SYS_CS_BURST 0x00000000 #define CONFIG_SYS_CS_DEADCYCLE 0x33333333 #define CONFIG_SYS_RESET_ADDRESS 0xff000000 /* * QUART Expanders support */ #if defined(CONFIG_QUART_CONSOLE) /* * We'll use NS16550 chip routines, */ #define CONFIG_SYS_NS16550 1 #define CONFIG_SYS_NS16550_SERIAL 1 #define CONFIG_CONS_INDEX 1 /* * To achieve necessary offset on SC16C554 * A0-A2 (register select) pins with NS16550 * functions (in struct NS16550), REG_SIZE * should be 4, because A0-A2 pins are connected * to DA2-DA4 address bus lines. */ #define CONFIG_SYS_NS16550_REG_SIZE 4 /* * LocalPlus Bus already inited in cpu_init_f(), * so can work with QUART's chip selects. * One of four SC16C554 UARTs is selected with * A3-A4 (DA5-DA6) lines. */ #if (CONFIG_QUART_CONSOLE > 0) && (CONFIG_QUART_CONSOLE < 5) && !defined(CONFIG_PRS200) #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CS2_START | (CONFIG_QUART_CONSOLE - 1)<<5) #elif (CONFIG_QUART_CONSOLE > 4) && (CONFIG_QUART_CONSOLE < 9) #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CS1_START | (CONFIG_QUART_CONSOLE - 5)<<5) #else #error "Wrong QUART expander number." #endif /* * SC16C554 chip's external crystal oscillator frequency * is 7.3728 MHz */ #define CONFIG_SYS_NS16550_CLK 7372800 #endif /* CONFIG_QUART_CONSOLE */ /*----------------------------------------------------------------------- * USB stuff *----------------------------------------------------------------------- */ #define CONFIG_USB_CLOCK 0x0001BBBB #define CONFIG_USB_CONFIG 0x00005000 #define CONFIG_AUTOBOOT_KEYED /* use key strings to stop autoboot */ #define CONFIG_AUTOBOOT_STOP_STR "432" #define CONFIG_SILENT_CONSOLE 1 #endif /* __CONFIG_H */