/* * Copyright (C) 2010 Albert ARIBAUD * * Based on original Kirkwood support which is * (C) Copyright 2009 * Marvell Semiconductor * Written-by: Prafulla Wadaskar * * SPDX-License-Identifier: GPL-2.0+ */ #ifndef _CONFIG_EDMINIV2_H #define _CONFIG_EDMINIV2_H /* * SPL */ #define CONFIG_SPL_FRAMEWORK #define CONFIG_SPL_LIBGENERIC_SUPPORT #define CONFIG_SPL_LIBCOMMON_SUPPORT #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_NOR_SUPPORT #define CONFIG_SPL_TEXT_BASE 0xffff0000 #define CONFIG_SPL_MAX_SIZE 0x0000fff0 #define CONFIG_SPL_STACK 0x00020000 #define CONFIG_SPL_BSS_START_ADDR 0x00020000 #define CONFIG_SPL_BSS_MAX_SIZE 0x0001ffff #define CONFIG_SYS_SPL_MALLOC_START 0x00040000 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x0001ffff #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/orion5x/u-boot-spl.lds" #define CONFIG_SPL_BOARD_INIT #define CONFIG_SYS_UBOOT_BASE 0xfff90000 #define CONFIG_SYS_UBOOT_START 0x00800000 #define CONFIG_SYS_TEXT_BASE 0x00800000 /* * Version number information */ #define CONFIG_IDENT_STRING " EDMiniV2" /* * High Level Configuration Options (easy to change) */ #define CONFIG_MARVELL 1 #define CONFIG_FEROCEON 1 /* CPU Core subversion */ #define CONFIG_88F5182 1 /* SOC Name */ #define CONFIG_MACH_EDMINIV2 1 /* Machine type */ #include /* * CLKs configurations */ /* * Board-specific values for Orion5x MPP low level init: * - MPPs 12 to 15 are SATA LEDs (mode 5) * - Others are GPIO/unused (mode 3 for MPP0, mode 5 for * MPP16 to MPP19, mode 0 for others */ #define ORION5X_MPP0_7 0x00000003 #define ORION5X_MPP8_15 0x55550000 #define ORION5X_MPP16_23 0x00005555 /* * Board-specific values for Orion5x GPIO low level init: * - GPIO3 is input (RTC interrupt) * - GPIO16 is Power LED control (0 = on, 1 = off) * - GPIO17 is Power LED source select (0 = CPLD, 1 = GPIO16) * - GPIO18 is Power Button status (0 = Released, 1 = Pressed) * - GPIO19 is SATA disk power toggle (toggles on 0-to-1) * - GPIO22 is SATA disk power status () * - GPIO23 is supply status for SATA disk () * - GPIO24 is supply control for board (write 1 to power off) * Last GPIO is 25, further bits are supposed to be 0. * Enable mask has ones for INPUT, 0 for OUTPUT. * Default is LED ON, board ON :) */ #define ORION5X_GPIO_OUT_ENABLE 0xfef4f0ca #define ORION5X_GPIO_OUT_VALUE 0x00000000 #define ORION5X_GPIO_IN_POLARITY 0x000000d0 /* * NS16550 Configuration */ #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE (-4) #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK #define CONFIG_SYS_NS16550_COM1 ORION5X_UART0_BASE /* * Serial Port configuration * The following definitions let you select what serial you want to use * for your console driver. */ #define CONFIG_CONS_INDEX 1 /*Console on UART0 */ #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_BAUDRATE_TABLE \ { 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 } /* * FLASH configuration */ #define CONFIG_SYS_FLASH_CFI #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ #define CONFIG_SYS_MAX_FLASH_SECT 11 /* max num of sects on one chip */ #define CONFIG_SYS_FLASH_BASE 0xfff80000 /* auto boot */ #define CONFIG_BOOTDELAY 3 /* default enable autoboot */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ #define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ #define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ /* * Commands configuration */ #define CONFIG_CMD_IDE /* * Network */ #ifdef CONFIG_CMD_NET #define CONFIG_MVGBE /* Enable Marvell GbE Driver */ #define CONFIG_MVGBE_PORTS {1} /* enable port 0 only */ #define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION /* don't randomize MAC */ #define CONFIG_PHY_BASE_ADR 0x8 #define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ #define CONFIG_NETCONSOLE /* include NetConsole support */ #define CONFIG_MII /* expose smi ove miiphy interface */ #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ #endif /* * IDE */ #ifdef CONFIG_CMD_IDE #define __io #define CONFIG_IDE_PREINIT #define CONFIG_DOS_PARTITION /* ED Mini V has an IDE-compatible SATA connector for port 1 */ #define CONFIG_MVSATA_IDE #define CONFIG_MVSATA_IDE_USE_PORT1 /* Needs byte-swapping for ATA data register */ #define CONFIG_IDE_SWAP_IO /* Data, registers and alternate blocks are at the same offset */ #define CONFIG_SYS_ATA_DATA_OFFSET (0x0100) #define CONFIG_SYS_ATA_REG_OFFSET (0x0100) #define CONFIG_SYS_ATA_ALT_OFFSET (0x0100) /* Each 8-bit ATA register is aligned to a 4-bytes address */ #define CONFIG_SYS_ATA_STRIDE 4 /* Controller supports 48-bits LBA addressing */ #define CONFIG_LBA48 /* A single bus, a single device */ #define CONFIG_SYS_IDE_MAXBUS 1 #define CONFIG_SYS_IDE_MAXDEVICE 1 /* ATA registers base is at SATA controller base */ #define CONFIG_SYS_ATA_BASE_ADDR ORION5X_SATA_BASE /* ATA bus 0 is orion5x port 1 on ED Mini V2 */ #define CONFIG_SYS_ATA_IDE0_OFFSET ORION5X_SATA_PORT1_OFFSET /* end of IDE defines */ #endif /* CMD_IDE */ /* * Common USB/EHCI configuration */ #ifdef CONFIG_CMD_USB #define CONFIG_USB_EHCI /* Enable EHCI USB support */ #define CONFIG_USB_EHCI_MARVELL #define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE #define CONFIG_USB_STORAGE #define CONFIG_DOS_PARTITION #define CONFIG_ISO_PARTITION #define CONFIG_SUPPORT_VFAT #endif /* CONFIG_CMD_USB */ /* * I2C related stuff */ #ifdef CONFIG_CMD_I2C #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MVTWSI #define CONFIG_I2C_MVTWSI_BASE0 ORION5X_TWSI_BASE #define CONFIG_SYS_I2C_SLAVE 0x0 #define CONFIG_SYS_I2C_SPEED 100000 #endif /* * Environment variables configurations */ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_SECT_SIZE 0x2000 /* 16K */ #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_OFFSET 0x4000 /* env starts here */ /* * Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (1024 * 256) /* 256kB for malloc() */ /* * Other required minimal configurations */ #define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ #define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ #define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ #define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ #define CONFIG_NR_DRAM_BANKS 1 #define CONFIG_SYS_LOAD_ADDR 0x00800000 #define CONFIG_SYS_MEMTEST_START 0x00400000 #define CONFIG_SYS_MEMTEST_END 0x007fffff #define CONFIG_SYS_RESET_ADDRESS 0xffff0000 #define CONFIG_SYS_MAXARGS 16 /* Enable command line editing */ #define CONFIG_CMDLINE_EDITING /* provide extensive help */ #define CONFIG_SYS_LONGHELP /* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE 0 #define CONFIG_SYS_INIT_SP_ADDR \ (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) #endif /* _CONFIG_EDMINIV2_H */