/* * U-boot - Configuration file for BF561 EZKIT board */ #ifndef __CONFIG_EZKIT561_H__ #define __CONFIG_EZKIT561_H__ #define CONFIG_VDSP 1 #define CONFIG_BF561 1 #define CFG_LONGHELP 1 #define CONFIG_CMDLINE_EDITING 1 #define CONFIG_BAUDRATE 57600 /* Set default serial console for bf537 */ #define CONFIG_UART_CONSOLE 0 #define CONFIG_EZKIT561 1 #define CONFIG_BOOTDELAY 5 #define CONFIG_PANIC_HANG 1 /* * Boot Mode Set * Blackfin can support several boot modes */ #define BF561_BYPASS_BOOT 0x21 #define BF561_PARA_BOOT 0x22 #define BF561_SPI_BOOT 0x24 /* Define the boot mode */ #define BFIN_BOOT_MODE BF561_BYPASS_BOOT /* This sets the default state of the cache on U-Boot's boot */ #define CONFIG_ICACHE_ON #define CONFIG_DCACHE_ON /* Define where the uboot will be loaded by on-chip boot rom */ #define APP_ENTRY 0x00001000 /* * Stringize definitions - needed for environmental settings */ #define STRINGIZE2(x) #x #define STRINGIZE(x) STRINGIZE2(x) /* * Board settings */ #define CONFIG_DRIVER_SMC91111 1 #define CONFIG_SMC91111_BASE 0x2C010300 #define CONFIG_ASYNC_EBIU_BASE CONFIG_SMC91111_BASE & ~(4*1024*1024) #define CONFIG_SMC_USE_32_BIT 1 #define CONFIG_MISC_INIT_R 1 /* * Clock settings */ /* CONFIG_CLKIN_HZ is any value in Hz */ #define CONFIG_CLKIN_HZ 30000000 /* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ /* 1=CLKIN/2 */ #define CONFIG_CLKIN_HALF 0 /* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ /* 1=bypass PLL */ #define CONFIG_PLL_BYPASS 0 /* CONFIG_VCO_MULT controls what the multiplier of the PLL is */ /* Values can range from 1-64 */ #define CONFIG_VCO_MULT 20 /* CONFIG_CCLK_DIV controls what the core clock divider is */ /* Values can be 1, 2, 4, or 8 ONLY */ #define CONFIG_CCLK_DIV 1 /* CONFIG_SCLK_DIV controls what the peripheral clock divider is */ /* Values can range from 1-15 */ #define CONFIG_SCLK_DIV 5 /* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ /* Values can range from 2-65535 */ /* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ #define CONFIG_SPI_BAUD 2 #define CONFIG_SPI_BAUD_INITBLOCK 4 /* * Network settings */ #if (CONFIG_DRIVER_SMC91111) #define CONFIG_IPADDR 192.168.0.15 #define CONFIG_NETMASK 255.255.255.0 #define CONFIG_GATEWAYIP 192.168.0.1 #define CONFIG_SERVERIP 192.168.0.2 #define CONFIG_HOSTNAME ezkit561 #define CONFIG_ROOTPATH /arm-cross-build/BF561/uClinux-dist/romfs #endif /* CONFIG_DRIVER_SMC91111 */ /* * Flash settings */ #define CFG_FLASH_CFI /* The flash is CFI compatible */ #define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CFG_FLASH_CFI_AMD_RESET #define CFG_ENV_IS_IN_FLASH 1 #define CFG_FLASH_BASE 0x20000000 #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 135 /* max number of sectors on one chip */ #define CFG_ENV_ADDR 0x20020000 #define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */ /* JFFS Partition offset set */ #define CFG_JFFS2_FIRST_BANK 0 #define CFG_JFFS2_NUM_BANKS 1 /* 512k reserved for u-boot */ #define CFG_JFFS2_FIRST_SECTOR 8 /* * SDRAM settings & memory map */ #define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */ #define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */ #define CONFIG_MEM_MT48LC16M16A2TG_75 1 #define CFG_SDRAM_BASE 0x00000000 #define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024) #define CFG_MEMTEST_START 0x0 /* memtest works on */ #define CFG_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024*1024) /* 1 ... 63 MB in DRAM */ #define CONFIG_LOADADDR 0x01000000 /* default load address */ #define CFG_LOAD_ADDR CONFIG_LOADADDR #define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN) #define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ #define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN) #define CFG_GBL_DATA_SIZE 0x4000 #define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE) #define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4) #define CONFIG_STACKSIZE (128*1024) /* regular stack */ #if ( CONFIG_CLKIN_HALF == 0 ) #define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) #else #define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) #endif #if (CONFIG_PLL_BYPASS == 0) #define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) #define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) #else #define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ #define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ #endif /* * Command settings */ #define CFG_AUTOLOAD "no" /* rarpb, bootp, dhcp commands will */ /* only perform a configuration */ /* lookup from the BOOTP/DHCP server */ /* but not try to load any image */ /* using TFTP */ #define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, */ /* currently its disabled */ #define CONFIG_BOOTCOMMAND "run ramboot" #define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600" #if (CONFIG_DRIVER_SMC91111) #define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \ CFG_CMD_PING | \ CFG_CMD_ELF | \ CFG_CMD_CACHE | \ CFG_CMD_JFFS2 | \ CFG_CMD_DHCP) #define CONFIG_EXTRA_ENV_SETTINGS \ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \ "$(rootpath) console=ttyBF0,57600\0" \ "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \ "ramboot=tftpboot $(loadaddr) linux; " \ "run ramargs; run addip; bootelf\0" \ "nfsboot=tftpboot $(loadaddr) linux; " \ "run nfsargs; run addip; bootelf\0" \ "update=tftpboot $(loadaddr) u-boot.bin; " \ "protect off 0x20000000 0x2003FFFF; " \ "erase 0x20000000 0x2003FFFF; " \ "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \ "" #else #define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \ CFG_CMD_ELF | \ CFG_CMD_CACHE | \ CFG_CMD_JFFS2) #define CONFIG_EXTRA_ENV_SETTINGS \ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ "flashboot=bootm 0x20100000\0" \ "" #endif #define CONFIG_COMMANDS ( CONFIG_COMMANDS1 | CONFIG_COMMANDS2 ) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include /* * Console settings */ #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } #define CFG_PROMPT "ezkit> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_LOADS_ECHO 1 /* * Miscellaneous configurable options */ #define CFG_HZ 1000 /* decrementer freq: 10 ms ticks */ #define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */ /* * FLASH organization and environment definitions */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ #define AMGCTLVAL 0x3F #define AMBCTL0VAL 0x7BB07BB0 #define AMBCTL1VAL 0xFFC27BB0 #ifdef CONFIG_VDSP #define ET_EXEC_VDSP 0x8 #define SHT_STRTAB_VDSP 0x1 #define ELFSHDRSIZE_VDSP 0x2C #define VDSP_ENTRY_ADDR 0xFFA00000 #endif #endif /* __CONFIG_EZKIT561_H__ */