/* * (C) Copyright 2007 DENX Software Engineering * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * ADS5121 board configuration file */ #ifndef __CONFIG_H #define __CONFIG_H #define DEBUG #undef DEBUG /* * Memory map for the ADS5121 board: * * 0x0000_0000 - 0x0FFF_FFFF DDR RAM (256 MB) * 0x3000_0000 - 0x3001_FFFF SRAM (128 KB) * 0x8000_0000 - 0x803F_FFFF IMMR (4 MB) * 0x8200_0000 - 0x8200_001F CPLD (32 B) * 0xFC00_0000 - 0xFFFF_FFFF NOR Boot FLASH (64 MB) */ /* * High Level Configuration Options */ #define CONFIG_E300 1 /* E300 Family */ #define CONFIG_MPC512X 1 /* MPC512X family */ #undef CONFIG_PCI #define CFG_MPC512X_CLKIN 66000000 /* in Hz */ #define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f() */ #define CFG_IMMR 0x80000000 #define CFG_MEMTEST_START 0x00200000 /* memtest region */ #define CFG_MEMTEST_END 0x00400000 /* * DDR Setup - manually set all parameters as there's no SPD etc. */ #define CFG_DDR_SIZE 256 /* MB */ #define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/ #define CFG_SDRAM_BASE CFG_DDR_BASE /* DDR Controller Configuration * * SYS_CFG: * [31:31] MDDRC Soft Reset: Diabled * [30:30] DRAM CKE pin: Enabled * [29:29] DRAM CLK: Enabled * [28:28] Command Mode: Enabled (For initialization only) * [27:25] DRAM Row Select: dram_row[15:0] = magenta_address[25:10] * [24:21] DRAM Bank Select: dram_bank[1:0] = magenta_address[11:10] * [20:19] Read Test: DON'T USE * [18:18] Self Refresh: Enabled * [17:17] 16bit Mode: Disabled * [16:13] Ready Delay: 2 * [12:12] Half DQS Delay: Disabled * [11:11] Quarter DQS Delay: Disabled * [10:08] Write Delay: 2 * [07:07] Early ODT: Disabled * [06:06] On DIE Termination: Disabled * [05:05] FIFO Overflow Clear: DON'T USE here * [04:04] FIFO Underflow Clear: DON'T USE here * [03:03] FIFO Overflow Pending: DON'T USE here * [02:02] FIFO Underlfow Pending: DON'T USE here * [01:01] FIFO Overlfow Enabled: Enabled * [00:00] FIFO Underflow Enabled: Enabled * TIME_CFG0 * [31:16] DRAM Refresh Time: 0 CSB clocks * [15:8] DRAM Command Time: 0 CSB clocks * [07:00] DRAM Precharge Time: 0 CSB clocks * TIME_CFG1 * [31:26] DRAM tRFC: * [25:21] DRAM tWR1: * [20:17] DRAM tWRT1: * [16:11] DRAM tDRR: * [10:05] DRAM tRC: * [04:00] DRAM tRAS: * TIME_CFG2 * [31:28] DRAM tRCD: * [27:23] DRAM tFAW: * [22:19] DRAM tRTW1: * [18:15] DRAM tCCD: * [14:10] DRAM tRTP: * [09:05] DRAM tRP: * [04:00] DRAM tRPA */ #define CFG_MDDRC_SYS_CFG 0xF8604200 #define CFG_MDDRC_SYS_CFG_RUN 0xE8604200 #define CFG_MDDRC_SYS_CFG_EN 0x30000000 #define CFG_MDDRC_TIME_CFG0 0x0000281E #define CFG_MDDRC_TIME_CFG0_RUN 0x01F4281E #define CFG_MDDRC_TIME_CFG1 0x54EC1168 #define CFG_MDDRC_TIME_CFG2 0x35210864 #define CFG_MICRON_NOP 0x01380000 #define CFG_MICRON_PCHG_ALL 0x01100400 #define CFG_MICRON_MR 0x01000022 #define CFG_MICRON_EM2 0x01020000 #define CFG_MICRON_EM3 0x01030000 #define CFG_MICRON_EN_DLL 0x01010000 #define CFG_MICRON_RST_DLL 0x01000932 #define CFG_MICRON_RFSH 0x01080000 #define CFG_MICRON_INIT_DEV_OP 0x01000832 #define CFG_MICRON_OCD_DEFAULT 0x01010780 #define CFG_MICRON_OCD_EXIT 0x01010400 /* DDR Priority Manager Configuration */ #define CFG_MDDRCGRP_PM_CFG1 0x000777AA #define CFG_MDDRCGRP_PM_CFG2 0x00000055 #define CFG_MDDRCGRP_HIPRIO_CFG 0x00000000 #define CFG_MDDRCGRP_LUT0_MU 0x11111117 #define CFG_MDDRCGRP_LUT0_ML 0x7777777A #define CFG_MDDRCGRP_LUT1_MU 0x4444EEEE #define CFG_MDDRCGRP_LUT1_ML 0xEEEEEEEE #define CFG_MDDRCGRP_LUT2_MU 0x44444444 #define CFG_MDDRCGRP_LUT2_ML 0x44444444 #define CFG_MDDRCGRP_LUT3_MU 0x55555555 #define CFG_MDDRCGRP_LUT3_ML 0x55555558 #define CFG_MDDRCGRP_LUT4_MU 0x11111111 #define CFG_MDDRCGRP_LUT4_ML 0x1111117C #define CFG_MDDRCGRP_LUT0_AU 0x33333377 #define CFG_MDDRCGRP_LUT0_AL 0x7777EEEE #define CFG_MDDRCGRP_LUT1_AU 0x11111111 #define CFG_MDDRCGRP_LUT1_AL 0x11111111 #define CFG_MDDRCGRP_LUT2_AU 0x11111111 #define CFG_MDDRCGRP_LUT2_AL 0x11111111 #define CFG_MDDRCGRP_LUT3_AU 0x11111111 #define CFG_MDDRCGRP_LUT3_AL 0x11111111 #define CFG_MDDRCGRP_LUT4_AU 0x11111111 #define CFG_MDDRCGRP_LUT4_AL 0x11111111 /* * NOR FLASH on the Local Bus */ #define CFG_FLASH_CFI /* use the Common Flash Interface */ #define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ #define CFG_FLASH_BASE 0xFC000000 /* start of FLASH */ #define CFG_FLASH_SIZE 0x04000000 /* max flash size in bytes */ #define CFG_FLASH_USE_BUFFER_WRITE #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ #define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE} #define CFG_MAX_FLASH_SECT 256 /* max sectors per device */ #undef CFG_FLASH_CHECKSUM /* * CPLD registers area is really only 32 bytes in size, but the smallest possible LP * window is 64KB */ #define CFG_CPLD_BASE 0x82000000 #define CFG_CPLD_SIZE 0x00010000 /* 64 KB */ #define CFG_SRAM_BASE 0x30000000 #define CFG_SRAM_SIZE 0x00020000 /* 128 KB */ #define CFG_CS0_CFG 0x05059310 /* ALE active low, data size 4bytes */ #define CFG_CS2_CFG 0x05059010 /* ALE active low, data size 1byte */ /* Use SRAM for initial stack */ #define CFG_INIT_RAM_ADDR CFG_SRAM_BASE /* Initial RAM address */ #define CFG_INIT_RAM_END CFG_SRAM_SIZE /* End of used area in RAM */ #define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET #define CFG_MONITOR_BASE TEXT_BASE /* Start of monitor */ #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ /* * Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO /* * Serial console configuration */ #define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 */ #if CONFIG_PSC_CONSOLE != 3 #error CONFIG_PSC_CONSOLE must be 3 #endif #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ #define CFG_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} #define CONSOLE_FIFO_TX_SIZE FIFOC_PSC3_TX_SIZE #define CONSOLE_FIFO_TX_ADDR FIFOC_PSC3_TX_ADDR #define CONSOLE_FIFO_RX_SIZE FIFOC_PSC3_RX_SIZE #define CONSOLE_FIFO_RX_ADDR FIFOC_PSC3_RX_ADDR #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ /* Use the HUSH parser */ #define CFG_HUSH_PARSER #ifdef CFG_HUSH_PARSER #define CFG_PROMPT_HUSH_PS2 "> " #endif /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* so disable bit-banged I2C */ #define CONFIG_I2C_MULTI_BUS #define CONFIG_I2C_CMD_TREE #define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F #if 0 #define CFG_I2C_NOPROBES {{0,0x69}} * Don't probe these addrs */ #endif /* * Ethernet configuration */ #define CONFIG_MPC512x_FEC 1 #define CONFIG_NET_MULTI #define CONFIG_PHY_ADDR 0x1 #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_ETHADDR 00:e0:5e:00:e5:14 #if 0 /* * Configure on-board RTC */ #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ #define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ #endif /* * Environment */ #define CFG_ENV_IS_IN_FLASH 1 /* This has to be a multiple of the Flash sector size */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) #define CFG_ENV_SIZE 0x2000 #define CFG_ENV_SECT_SIZE 0x40000 /* one sector (256K) for env */ /* Address and size of Redundant Environment Sector */ #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #if defined(CONFIG_PCI) #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ | CFG_CMD_PCI \ | CFG_CMD_NET \ | CFG_CMD_PING \ ) #else #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ | CFG_CMD_NET \ | CFG_CMD_PING \ | CFG_CMD_MII \ | CFG_CMD_I2C) #endif #include /* * Watchdog timeout = CFG_WATCHDOG_VALUE * 65536 / IPS clock. * For example, when IPS is set to 66MHz and CFG_WATCHDOG_VALUE is set * to 0xFFFF, watchdog timeouts after about 64s. For details refer * to chapter 36 of the MPC5121e Reference Manual. */ #define CONFIG_WATCHDOG /* enable watchdog */ #define CFG_WATCHDOG_VALUE 0xFFFF /* * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif #define CFG_HID0_INIT 0x000000000 #define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK #define CFG_HID2 HID2_HBE /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /* * Environment Configuration */ #define CONFIG_ENV_OVERWRITE #define CONFIG_HOSTNAME ads5121 #define CONFIG_ROOTPATH /nfsroot/rootfs #define CONFIG_BOOTFILE uImage #define CONFIG_IPADDR 192.168.160.77 #define CONFIG_SERVERIP 192.168.1.1 #define CONFIG_GATEWAYIP 192.168.1.1 #define CONFIG_NETMASK 255.255.0.0 #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ //#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ #define CONFIG_BOOTDELAY -1 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #define CONFIG_BAUDRATE 115200 #define CONFIG_PREBOOT "echo;" \ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ "echo" #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "addip=setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ ":${hostname}:${netdev}:off panic=1\0" \ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ "flash_nfs=run nfsargs addip addtty;" \ "bootm ${kernel_addr}\0" \ "flash_self=run ramargs addip addtty;" \ "bootm ${kernel_addr} ${ramdisk_addr}\0" \ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ "bootm\0" \ "load=tftp 100000 /tftpboot/ads5121/u-boot.bin\0" \ "update=protect off fff00000 fff3ffff; " \ "era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \ "upd=run load;run update\0" \ "" #define CONFIG_NFSBOOTCOMMAND \ "setenv bootargs root=/dev/nfs rw " \ "nfsroot=$serverip:$rootpath " \ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr - $fdtaddr" #define CONFIG_RAMBOOTCOMMAND \ "setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $ramdiskaddr $ramdiskfile;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr $ramdiskaddr $fdtaddr" #define CONFIG_BOOTCOMMAND "run flash_self" #endif /* __CONFIG_H */