/* * (C) Copyright 2004 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * Sam Song, IEMC. SHU, samsongshu@yahoo.com.cn * * SPDX-License-Identifier: GPL-2.0+ */ /* * board/config.h - configuration options, board specific */ /* Yoo. Jonghoon, IPone, yooth@ipone.co.kr * U-BOOT port on RPXlite board */ /* * Sam Song, IEMC. SHU, samsongshu@yahoo.com.cn * U-BOOT port on RPXlite DW version board--RPXlite_DW * June 8 ,2004 */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ /* #define DEBUG 1 */ /* #define DEPLOYMENT 1 */ #undef CONFIG_MPC860 #define CONFIG_MPC823 1 /* This is a MPC823e CPU. */ #define CONFIG_RPXLITE 1 /* RPXlite DW version board */ #define CONFIG_SYS_TEXT_BASE 0xff000000 #ifdef CONFIG_LCD /* with LCD controller ? */ #define CONFIG_MPC8XX_LCD #define CONFIG_SPLASH_SCREEN /* ... with splashscreen support*/ #endif #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ #undef CONFIG_8xx_CONS_SMC2 #undef CONFIG_8xx_CONS_NONE #define CONFIG_BAUDRATE 9600 /* console default baudrate = 9600bps */ #ifdef DEBUG #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ #else #define CONFIG_BOOTDELAY 6 /* autoboot after 6 seconds */ #ifdef DEPLOYMENT #define CONFIG_BOOT_RETRY_TIME -1 #define CONFIG_AUTOBOOT_KEYED #define CONFIG_AUTOBOOT_PROMPT \ "autoboot in %d seconds (stop with 'st')...\n", bootdelay #define CONFIG_AUTOBOOT_STOP_STR "st" #define CONFIG_ZERO_BOOTDELAY_CHECK #define CONFIG_RESET_TO_RETRY 1 #define CONFIG_BOOT_RETRY_MIN 1 #endif /* DEPLOYMENT */ #endif /* DEBUG */ /* pre-boot commands */ #define CONFIG_PREBOOT "setenv stdout serial;setenv stdin serial" #undef CONFIG_BOOTARGS #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "nfsargs=setenv bootargs console=tty0 console=ttyS0,9600 " \ "root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs console=tty0 root=/dev/ram rw\0" \ "addip=setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ ":${hostname}:${netdev}:off panic=1\0" \ "flash_nfs=run nfsargs addip;" \ "bootm ${kernel_addr}\0" \ "flash_self=run ramargs addip;" \ "bootm ${kernel_addr} ${ramdisk_addr}\0" \ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "gatewayip=172.16.115.254\0" \ "netmask=255.255.255.0\0" \ "kernel_addr=ff040000\0" \ "ramdisk_addr=ff200000\0" \ "ku=era ${kernel_addr} ff1fffff;cp.b 100000 ${kernel_addr} " \ "${filesize};md ${kernel_addr};" \ "echo kernel updating finished\0" \ "uu=protect off 1:0-4;era 1:0-4;cp.b 100000 ff000000 " \ "${filesize};md ff000000;" \ "echo u-boot updating finished\0" \ "eu=protect off 1:6;era 1:6;reset\0" \ "lcd=setenv stdout lcd;setenv stdin lcd\0" \ "ser=setenv stdout serial;setenv stdin serial\0" \ "verify=no" #define CONFIG_BOOTCOMMAND "run flash_self" #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ #undef CONFIG_WATCHDOG /* watchdog disabled */ #undef CONFIG_STATUS_LED /* disturbs display. Status LED disabled. */ /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_BOOTFILESIZE #if 1 /* Enable this stuff could make image enlarge about 25KB. Mask it if you don't want the advanced function */ /* * Command line configuration. */ #include #define CONFIG_CMD_ASKENV #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_PING #define CONFIG_CMD_ELF #define CONFIG_CMD_REGINFO #define CONFIG_CMD_DHCP #ifdef CONFIG_SPLASH_SCREEN #define CONFIG_CMD_BMP #endif /* test-only */ #define CONFIG_SYS_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ #define CONFIG_SYS_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */ #define CONFIG_NETCONSOLE #endif /* 1 */ /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "u-boot>" /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x0040000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ /*----------------------------------------------------------------------- * Internal Memory Mapped Register */ #define CONFIG_SYS_IMMR 0xFA200000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR #define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0xFF000000 #if defined(DEBUG) || defined(CONFIG_CMD_IDE) #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #else #define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ #endif #define CONFIG_SYS_MONITOR_BASE 0xFF000000 #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #ifdef CONFIG_ENV_IS_IN_NVRAM #define CONFIG_ENV_ADDR 0xFA000100 #define CONFIG_ENV_SIZE 0x1000 #else #define CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_OFFSET 0x30000 /* Offset of Environment Sector */ #define CONFIG_ENV_SIZE 0x8000 /* Total Size of Environment Sector */ #endif /* CONFIG_ENV_IS_IN_NVRAM */ #define CONFIG_SYS_RESET_ADDRESS ((ulong)((((immap_t *)CONFIG_SYS_IMMR)->im_clkrst.res))) /*----------------------------------------------------------------------- * Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ #endif /*----------------------------------------------------------------------- * SYPCR - System Protection Control 32-bit 12-35 * SYPCR can only be written once after reset! *----------------------------------------------------------------------- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze */ #if defined(CONFIG_WATCHDOG) #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) #else #define CONFIG_SYS_SYPCR (SYPCR_SWTC | 0x00000600 | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) #endif /* We can get SYPCR: 0xFFFF0689. */ /*----------------------------------------------------------------------- * SIUMCR - SIU Module Configuration 32-bit 12-30 *----------------------------------------------------------------------- * PCMCIA config., multi-function pin tri-state */ #define CONFIG_SYS_SIUMCR (SIUMCR_MLRC10) /* SIUMCR:0x00000800 */ /*--------------------------------------------------------------------- * TBSCR - Time Base Status and Control 16-bit 12-16 *--------------------------------------------------------------------- * Clear Reference Interrupt Status, Timebase freezing enabled */ #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE) /* TBSCR: 0x00C3 [SAM] */ /*----------------------------------------------------------------------- * RTCSC - Real-Time Clock Status and Control Register 16-bit 12-18 *----------------------------------------------------------------------- * [RTC enabled but not stopped on FRZ] */ #define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTE) /* RTCSC:0x00C1 */ /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control 16-bit 12-23 *----------------------------------------------------------------------- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled * [Periodic timer enabled,Periodic timer interrupt disable. ] */ #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) /* PISCR:0x0083 */ /*----------------------------------------------------------------------- * PLPRCR - PLL, Low-Power, and Reset Control Register 32-bit 5-7 *----------------------------------------------------------------------- * Reset PLL lock status sticky bit, timer expired status bit and timer * interrupt status bit */ /* up to 64 MHz we use a 1:2 clock */ #if defined(RPXlite_64MHz) #define CONFIG_SYS_PLPRCR ( (7 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS ) /*PLPRCR: 0x00700000. */ #else #define CONFIG_SYS_PLPRCR ( (5 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS ) #endif /*----------------------------------------------------------------------- * SCCR - System Clock and reset Control Register 5-3 *----------------------------------------------------------------------- * Set clock output, timebase and RTC source and divider, * power management and some other internal clocks */ #define SCCR_MASK SCCR_EBDF00 /* Up to 48MHz system clock, we use 1:1 SYSTEM/BUS ratio */ #if defined(RPXlite_64MHz) #define CONFIG_SYS_SCCR ( SCCR_TBS | SCCR_EBDF01 ) /* %%%SCCR:0x02020000 */ #else #define CONFIG_SYS_SCCR ( SCCR_TBS | SCCR_EBDF00 ) /* %%%SCCR:0x02000000 */ #endif /*----------------------------------------------------------------------- * PCMCIA stuff *----------------------------------------------------------------------- */ #define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) #define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) #define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) #define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) #define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) #define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) #define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) #define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) /*----------------------------------------------------------------------- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) *----------------------------------------------------------------------- */ #define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */ #define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ #undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ #undef CONFIG_IDE_LED /* LED for ide not supported */ #undef CONFIG_IDE_RESET /* reset for ide not supported */ #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ #define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 #define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR /* Offset for data I/O */ #define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) /* Offset for normal register accesses */ #define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) /* Offset for alternate registers */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 #define CONFIG_SYS_DER 0 /* * Init Memory Controller: * * BR0 and OR0 (FLASH) */ #define FLASH_BASE_PRELIM 0xFC000000 /* FLASH base */ #define CONFIG_SYS_PRELIM_OR_AM 0xFC000000 /* OR addr mask */ /* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 8, ETHR = 0, BIH = 1 */ #define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_8_CLK | OR_BI) #define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) #define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V) /* * BR1 and OR1 (SDRAM) * */ #define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */ #define SDRAM_MAX_SIZE 0x08000000 /* max 128 MB in system */ /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ #define CONFIG_SYS_OR_TIMING_SDRAM 0x00000E00 #define CONFIG_SYS_OR_AM_SDRAM (-(SDRAM_MAX_SIZE & OR_AM_MSK)) #define CONFIG_SYS_OR1_PRELIM ( CONFIG_SYS_OR_AM_SDRAM | CONFIG_SYS_OR_TIMING_SDRAM ) #define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) /* RPXlite mem setting */ #define CONFIG_SYS_BR3_PRELIM 0xFA400001 /* BCSR */ #define CONFIG_SYS_OR3_PRELIM 0xFF7F8900 #define CONFIG_SYS_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */ #define CONFIG_SYS_OR4_PRELIM 0xFFFE0040 /* * Memory Periodic Timer Prescaler */ /* periodic timer for refresh */ #if defined(RPXlite_64MHz) #define CONFIG_SYS_MAMR_PTA 32 #else #define CONFIG_SYS_MAMR_PTA 20 #endif /* * Refresh clock Prescalar */ #define CONFIG_SYS_MPTPR MPTPR_PTP_DIV2 /* * MAMR settings for SDRAM */ /* 9 column SDRAM */ #define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10) /* CONFIG_SYS_MAMR_9COL:0x20904000 @ 64MHz */ /*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */ /* Configuration variable added by yooth. */ /*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */ /* * BCSRx * * Board Status and Control Registers * */ #define BCSR0 0xFA400000 #define BCSR1 0xFA400001 #define BCSR2 0xFA400002 #define BCSR3 0xFA400003 #define BCSR0_ENMONXCVR 0x01 /* Monitor XVCR Control */ #define BCSR0_ENNVRAM 0x02 /* CS4# Control */ #define BCSR0_LED5 0x04 /* LED5 control 0='on' 1='off' */ #define BCSR0_LED4 0x08 /* LED4 control 0='on' 1='off' */ #define BCSR0_FULLDPLX 0x10 /* Ethernet XCVR Control */ #define BCSR0_COLTEST 0x20 #define BCSR0_ETHLPBK 0x40 #define BCSR0_ETHEN 0x80 #define BCSR1_PCVCTL7 0x01 /* PC Slot B Control */ #define BCSR1_PCVCTL6 0x02 #define BCSR1_PCVCTL5 0x04 #define BCSR1_PCVCTL4 0x08 #define BCSR1_IPB5SEL 0x10 #define BCSR1_SMC1CTS 0x40 /* Added by SAM. */ #define BCSR1_SMC1TRS 0x80 /* Added by SAM. */ #define BCSR2_ENRTCIRQ 0x01 /* Added by SAM. */ #define BCSR2_ENBRG1 0x04 /* Added by SAM. */ #define BCSR2_ENPA5HDR 0x08 /* USB Control */ #define BCSR2_ENUSBCLK 0x10 #define BCSR2_USBPWREN 0x20 #define BCSR2_USBSPD 0x40 #define BCSR2_USBSUSP 0x80 #define BCSR3_BWKAPWR 0x01 /* Changed by SAM. Backup battery situation */ #define BCSR3_IRQRTC 0x02 /* Changed by SAM. NVRAM Battery */ #define BCSR3_RDY_BSY 0x04 /* Changed by SAM. Flash Operation */ #define BCSR3_MPLX_LIN 0x08 /* Changed by SAM. Linear or Multiplexed address Mode */ #define BCSR3_D27 0x10 /* Dip Switch settings */ #define BCSR3_D26 0x20 #define BCSR3_D25 0x40 #define BCSR3_D24 0x80 /* * Environment setting */ #define CONFIG_ETHADDR 00:10:EC:00:37:5B #define CONFIG_IPADDR 172.16.115.7 #define CONFIG_SERVERIP 172.16.115.6 #define CONFIG_ROOTPATH "/workspace/myfilesystem/target/" #define CONFIG_BOOTFILE "uImage.rpxusb" #define CONFIG_HOSTNAME LITE_H1_DW #endif /* __CONFIG_H */