/* * (C) Copyright 2003 * MuLogic B.V. * * (C) Copyright 2002 * Simple Network Magic Corporation * * (C) Copyright 2000 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * SPDX-License-Identifier: GPL-2.0+ */ /* * board/config.h - configuration options, board specific */ #ifndef __CONFIG_H #define __CONFIG_H /* various debug settings */ #undef CONFIG_SYS_DEVICE_NULLDEV /* null device */ #undef CONFIG_SILENT_CONSOLE /* silent console */ #undef CONFIG_SYS_CONSOLE_INFO_QUIET /* silent console ? */ #undef DEBUG_FLASH /* debug flash code */ #undef FLASH_DEBUG /* debug fash code */ #undef DEBUG_ENV /* debug environment code */ #define CONFIG_SYS_DIRECT_FLASH_TFTP 1 /* allow direct tftp to flash */ #define CONFIG_ENV_OVERWRITE 1 /* allow overwrite MAC address */ /* * High Level Configuration Options * (easy to change) */ #define CONFIG_MPC850 1 /* This is a MPC850 CPU */ #define CONFIG_QS850 1 /* ...on a QS850 module */ #define CONFIG_SCC2_ENET 1 /* SCC2 10BaseT ethernet */ #define CONFIG_SYS_TEXT_BASE 0xFFF00000 /* Select the target clock speed */ #undef CONFIG_CLOCK_16MHZ /* cpu=16,777,216 Hz, mem=16Mhz */ #undef CONFIG_CLOCK_33MHZ /* cpu=33,554,432 Hz, mem=33Mhz */ #undef CONFIG_CLOCK_50MHZ /* cpu=49,971,200 Hz, mem=33Mhz */ #define CONFIG_CLOCK_66MHZ 1 /* cpu=67,108,864 Hz, mem=66Mhz */ #undef CONFIG_CLOCK_80MHZ /* cpu=79,986,688 Hz, mem=33Mhz */ #ifdef CONFIG_CLOCK_16MHZ #define CONFIG_CLOCK_MULT 512 #endif #ifdef CONFIG_CLOCK_33MHZ #define CONFIG_CLOCK_MULT 1024 #endif #ifdef CONFIG_CLOCK_50MHZ #define CONFIG_CLOCK_MULT 1525 #endif #ifdef CONFIG_CLOCK_66MHZ #define CONFIG_CLOCK_MULT 2048 #endif #ifdef CONFIG_CLOCK_80MHZ #define CONFIG_CLOCK_MULT 2441 #endif /* choose flash size, 4Mb or 8Mb */ #define CONFIG_FLASH_4MB 1 /* board has 4Mb flash */ #undef CONFIG_FLASH_8MB /* board has 8Mb flash */ #define CONFIG_CLOCK_BASE 32768 /* Base clock input freq */ #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ #undef CONFIG_8xx_CONS_SMC2 #undef CONFIG_8xx_CONS_NONE #define CONFIG_BAUDRATE 38400 /* console baudrate = 38.4kbps */ #undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */ /* Define default IP addresses */ #define CONFIG_IPADDR 192.168.1.99 /* own ip address */ #define CONFIG_SERVERIP 192.168.1.19 /* used for tftp (not nfs?) */ /* message to say directly after booting */ #define CONFIG_PREBOOT "echo '';" \ "echo 'type:';" \ "echo 'run boot_nfs to boot to NFS';" \ "echo 'run boot_flash to boot to flash';" \ "echo '';" \ "echo 'run flash_rootfs to install a new rootfs';" \ "echo 'run flash_env to clear the env sector';" \ "echo 'run flash_rw to clear the rw fs';" \ "echo 'run flash_uboot to install a new u-boot';" \ "echo 'run flash_kernel to install a new kernel';" /* wait 5 seconds before executing CONFIG_BOOTCOMMAND */ #define CONFIG_BOOTDELAY 5 #define CONFIG_BOOTCOMMAND "run boot_nfs" #undef CONFIG_BOOTARGS /* made by set_nfs of set_flash */ /* Our flash filesystem looks like this * * 4Mb board: * ffc0 0000 - ffeb ffff root filesystem (jffs2) (~3Mb) * ffec 0000 - ffed ffff read-write filesystem (ext2) * ffee 0000 - ffef ffff environment * fff0 0000 - fff1 ffff u-boot * fff2 0000 - ffff ffff linux kernel * * 8Mb board: * ff80 0000 - ffeb ffff root filesystem (jffs2) (~7Mb) * ffec 0000 - ffed ffff read-write filesystem (ext2) * ffee 0000 - ffef ffff environment * fff0 0000 - fff1 ffff u-boot * fff2 0000 - ffff ffff linux kernel * */ /* environment for 4Mb board */ #ifdef CONFIG_FLASH_4MB #define CONFIG_EXTRA_ENV_SETTINGS \ "serial#=QS850\0" \ "hostname=qs850\0" \ "netdev=eth0\0" \ "ethaddr=00:01:02:B4:36:56\0" \ "rootpath=/exports/rootfs\0" \ "mtdparts=mtdparts=phys:2816k(root),128k(rw),128k(env),128k(u-boot),-(kernel)\0" \ /* fill in variables */ \ "set_ip=setenv ip ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off\0" \ "set_nfs=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath $ip init=/sbin/init $mtdparts\0" \ "set_flash=setenv bootargs root=/dev/mtdblock1 ro $ip init=/sbin/init $mtdparts\0" \ /* commands */ \ "boot_nfs=run set_ip; run set_nfs; tftp 0x400000 /tftpboot/vmlinux.UBoot; bootm 0x400000\0" \ "boot_flash=run set_ip; run set_flash; bootm fff20000\0" \ /* reinstall flash parts */ \ "flash_rootfs=protect off ffc00000 ffebffff; era ffc00000 ffebffff; tftp ffc00000 /tftpboot/rootfs.jffs2\0" \ "flash_rw=protect off ffec0000 ffedffff; era ffec0000 ffedffff\0" \ "flash_env=protect off ffee0000 ffefffff; era ffee0000 ffefffff\0" \ "flash_uboot=protect off fff00000 fff1ffff; era fff00000 fff1ffff; tftp fff00000 /tftpboot/u-boot.4mb.bin\0" \ "flash_kernel=protect off fff20000 ffffffff; era fff20000 ffffffff; tftp fff20000 /tftpboot/vmlinux.UBoot\0" #endif /* CONFIG_FLASH_4MB */ /* environment for 8Mb board */ #ifdef CONFIG_FLASH_8MB #define CONFIG_EXTRA_ENV_SETTINGS \ "serial#=QS850\0" \ "hostname=qs850\0" \ "netdev=eth0\0" \ "ethaddr=00:01:02:B4:36:56\0" \ "rootpath=/exports/rootfs\0" \ "mtdparts=mtdparts=phys:6912k(root),128k(rw),128k(env),128k(u-boot),-(kernel)\0" \ /* fill in variables */ \ "set_ip=setenv ip ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off\0" \ "set_nfs=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath $ip init=/sbin/init $mtdparts\0" \ "set_flash=setenv bootargs root=/dev/mtdblock1 ro $ip init=/sbin/init $mtdparts\0" \ /* commands */ \ "boot_nfs=run set_ip; run set_nfs; tftp 0x400000 /tftpboot/vmlinux.UBoot; bootm 0x400000\0" \ "boot_flash=run set_ip; run set_flash; bootm fff20000\0" \ /* reinstall flash parts */ \ "flash_rootfs=protect off ff800000 ffebffff; era ff800000 ffebffff; tftp ff800000 /tftpboot/rootfs.jffs2\0" \ "flash_rw=protect off ffec0000 ffedffff; era ffec0000 ffedffff\0" \ "flash_env=protect off ffee0000 ffefffff; era ffee0000 ffefffff\0" \ "flash_uboot=protect off fff00000 fff1ffff; era fff00000 fff1ffff; tftp fff00000 /tftpboot/u-boot.8mb.bin\0" \ "flash_kernel=protect off fff20000 ffffffff; era fff20000 ffffffff; tftp fff20000 /tftpboot/vmlinux.UBoot\0" #endif /* CONFIG_FLASH_8MB */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ #undef CONFIG_WATCHDOG /* watchdog disabled */ #undef CONFIG_STATUS_LED /* Status LED disabled */ #undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_BOOTFILESIZE #undef CONFIG_MAC_PARTITION #undef CONFIG_DOS_PARTITION #define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ /* * Command line configuration. */ #define CONFIG_CMD_BDI #define CONFIG_CMD_BOOTD #define CONFIG_CMD_CONSOLE #define CONFIG_CMD_DATE #define CONFIG_CMD_SAVEENV #define CONFIG_CMD_FLASH #define CONFIG_CMD_IMI #define CONFIG_CMD_IMMAP #define CONFIG_CMD_MEMORY #define CONFIG_CMD_NET #define CONFIG_CMD_RUN /*----------------------------------------------------------------------- * Environment variable storage is in FLASH, one sector before U-boot */ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128Kb, one whole sector */ #define CONFIG_ENV_SIZE 0x2000 /* 8kb */ #define CONFIG_ENV_ADDR 0xffee0000 /* address of env sector */ /*----------------------------------------------------------------------- * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */ /*----------------------------------------------------------------------- * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ /*----------------------------------------------------------------------- * Internal Memory Mapped Register */ #define CONFIG_SYS_IMMR 0xFF000000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR #define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0xFF800000 /* Allow an 8Mbyte window */ #define FLASH_BASE0_4M_PRELIM 0xFFC00000 /* Base for 4M Flash */ #define FLASH_BASE0_8M_PRELIM 0xFF800000 /* Base for 8M Flash */ #define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ #define CONFIG_SYS_MONITOR_BASE 0xFFF00000 /* U-boot location */ #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * TODO flash parameters * FLASH organization for Intel Strataflash */ #undef CONFIG_SYS_FLASH_16BIT /* 32-bit wide flash memory */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ /*----------------------------------------------------------------------- * Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ #endif /*----------------------------------------------------------------------- * SYPCR - System Protection Control 11-9 * SYPCR can only be written once after reset! *----------------------------------------------------------------------- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze */ #ifdef CONFIG_WATCHDOG #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP) #else #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWRI | SYPCR_SWP) #endif /*----------------------------------------------------------------------- * SIUMCR - SIU Module Configuration 11-6 *----------------------------------------------------------------------- */ #define CONFIG_SYS_SIUMCR (SIUMCR_DLK | SIUMCR_DPC | SIUMCR_MPRE | SIUMCR_MLRC01 | SIUMCR_GB5E) /*----------------------------------------------------------------------- * TBSCR - Time Base Status and Control 11-26 *----------------------------------------------------------------------- */ #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) /*----------------------------------------------------------------------- * RTCSC - Real-Time Clock Status and Control Register 11-27 *----------------------------------------------------------------------- */ #define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control 11-31 *----------------------------------------------------------------------- */ #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) /*----------------------------------------------------------------------- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 *----------------------------------------------------------------------- */ /* MF (Multiplication Factor of SPLL) */ /* Sets the QS850 to specified clock from 32KHz clock at EXTAL. */ #define vPLPRCR_MF ((CONFIG_CLOCK_MULT+1) << 20) #define CONFIG_SYS_PLPRCR (vPLPRCR_MF | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | PLPRCR_LOLRE) /*----------------------------------------------------------------------- * SCCR - System Clock and reset Control Register 15-27 *----------------------------------------------------------------------- */ #if defined(CONFIG_CLOCK_16MHZ) || defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_50MHZ) #define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_EBDF00 | SCCR_DFBRG00) #define CONFIG_SYS_BRGCLK_PRESCALE 1 #endif #if defined(CONFIG_CLOCK_66MHZ) #define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_EBDF00 | SCCR_DFBRG01) #define CONFIG_SYS_BRGCLK_PRESCALE 4 #endif #if defined(CONFIG_CLOCK_80MHZ) #define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_EBDF01 | SCCR_DFBRG01) #define CONFIG_SYS_BRGCLK_PRESCALE 4 #endif #define SCCR_MASK CONFIG_SYS_SCCR /*----------------------------------------------------------------------- * Debug Enable Register * 0x73E67C0F - All interrupts handled by BDM * 0x00824001 - Only interrupts needed by MWDebug.exe handled by BDM *----------------------------------------------------------------------- #define CONFIG_SYS_DER 0x73E67C0F #define CONFIG_SYS_DER 0x0082400F #------------------------------------------------------------------------- # Program the Debug Enable Register (DER). This register provides the user # with the reason for entering into the debug mode. We want all conditions # to end up as an exception. We don't want to enter into debug mode for # any condition. See the back of of the Development Support section of the # MPC860 User Manual for a description of this register. #------------------------------------------------------------------------- */ #define CONFIG_SYS_DER 0 /*----------------------------------------------------------------------- * Memory Controller Initialization Constants *----------------------------------------------------------------------- */ /* * BR0 and OR0 (AMD dual FLASH devices) * Base address = 0xFFF0_0000 - 0xFFF7_FFFF (After relocation) */ #define CONFIG_SYS_PRELIM_OR_AM #define CONFIG_SYS_OR_TIMING_FLASH /* *----------------------------------------------------------------------- * Base Register 0 (BR0): Bank 0 is assigned to the 8Mbyte (2M X 32) * flash that resides on the QS850. *----------------------------------------------------------------------- */ /* BA (Base Address) = 0xFF80+0b for a total of 17 bits. 17 bit base addr */ /* represents a minumum 32K block size. */ #define vBR0_BA ((0xFF80 << 16) + (0 << 15)) #define CONFIG_SYS_BR0_PRELIM (vBR0_BA | BR_V) /* AM (Address Mask) = 0xFF80+0b = We've masked the upper 9 bits */ /* which defines a 8 Mbyte memory block. */ #define vOR0_AM ((0xFF80 << 16) + (0 << 15)) #if defined(CONFIG_CLOCK_50MHZ) || defined(CONFIG_CLOCK_80MHZ) /* 0101 = Add a 5 clock cycle wait state */ #define CONFIG_SYS_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | 0R_ACS_DIV4 | OR_BI | OR_SCY_5_CLK) #endif #if defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_66MHZ) /* 0011 = Add a 3 clock cycle wait state */ /* 29.8ns clock * (3 + 2) = 149ns cycle time */ #define CONFIG_SYS_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK) #endif #if defined(CONFIG_CLOCK_16MHZ) /* 0010 = Add a 2 clock cycle wait state */ #define CONFIG_SYS_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_2_CLK) #endif /* * BR1 and OR1 (SDRAM) * Base Address = 0x00000000 - 0x00FF_FFFF (16M After relocation) * Base Address = 0x00000000 - 0x01FF_FFFF (32M After relocation) * Base Address = 0x00000000 - 0x03FF_FFFF (64M After relocation) * Base Address = 0x00000000 - 0x07FF_FFFF (128M After relocation) */ #define SDRAM_BASE 0x00000000 /* SDRAM bank */ #define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */ /* AM (Address Mask) = 0xF800+0b = We've masked the upper 5 bits which * represents a 128 Mbyte block the DRAM in * this address base. */ #define vOR1_AM ((0xF800 << 16) + (0 << 15)) #define vBR1_BA ((0x0000 << 16) + (0 << 15)) #define CONFIG_SYS_OR1 (vOR1_AM | OR_CSNT_SAM | OR_BI) #define CONFIG_SYS_BR1 (vBR1_BA | BR_MS_UPMA | BR_V) /* Machine A Mode Register */ /* PTA Periodic Timer A */ #if defined(CONFIG_CLOCK_80MHZ) #define vMAMR_PTA (19 << 24) #endif #if defined(CONFIG_CLOCK_66MHZ) #define vMAMR_PTA (16 << 24) #endif #if defined(CONFIG_CLOCK_50MHZ) #define vMAMR_PTA (195 << 24) #endif #if defined(CONFIG_CLOCK_33MHZ) #define vMAMR_PTA (131 << 24) #endif #if defined(CONFIG_CLOCK_16MHZ) #define vMAMR_PTA (65 << 24) #endif /* For boards with 16M of SDRAM */ #define SDRAM_16M_MAX_SIZE 0x01000000 /* max 16MB SDRAM */ #define CONFIG_SYS_16M_MAMR (vMAMR_PTA | MAMR_AMA_TYPE_0 | MAMR_DSA_2_CYCL | MAMR_G0CLA_A11 |\ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) /* For boards with 32M of SDRAM */ #define SDRAM_32M_MAX_SIZE 0x02000000 /* max 32MB SDRAM */ #define CONFIG_SYS_32M_MAMR (vMAMR_PTA | MAMR_AMA_TYPE_1 | MAMR_DSA_2_CYCL | MAMR_G0CLA_A10 |\ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) /* Memory Periodic Timer Prescaler Register */ #if defined(CONFIG_CLOCK_66MHZ) || defined(CONFIG_CLOCK_80MHZ) /* Divide by 32 */ #define CONFIG_SYS_MPTPR 0x02 #endif #if defined(CONFIG_CLOCK_16MHZ) || defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_50MHZ) /* Divide by 16 */ #define CONFIG_SYS_MPTPR 0x04 #endif /* * BR2 and OR2 (Unused) * Base address = 0xF020_0000 - 0xF020_0FFF * */ #define CONFIG_SYS_OR2_PRELIM 0xFFF00000 #define CONFIG_SYS_BR2_PRELIM 0xF0200000 /* * BR3 and OR3 (External Bus CS3) * Base address = 0xF030_0000 - 0xF030_0FFF * */ #define CONFIG_SYS_OR3_PRELIM 0xFFF00000 #define CONFIG_SYS_BR3_PRELIM 0xF0300000 /* * BR4 and OR4 (External Bus CS3) * Base address = 0xF040_0000 - 0xF040_0FFF * */ #define CONFIG_SYS_OR4_PRELIM 0xFFF00000 #define CONFIG_SYS_BR4_PRELIM 0xF0400000 /* * BR4 and OR4 (External Bus CS3) * Base address = 0xF050_0000 - 0xF050_0FFF * */ #define CONFIG_SYS_OR5_PRELIM 0xFFF00000 #define CONFIG_SYS_BR5_PRELIM 0xF0500000 /* * BR6 and OR6 (Unused) * Base address = 0xF060_0000 - 0xF060_0FFF * */ #define CONFIG_SYS_OR6_PRELIM 0xFFF00000 #define CONFIG_SYS_BR6_PRELIM 0xF0600000 /* * BR7 and OR7 (Unused) * Base address = 0xF070_0000 - 0xF070_0FFF * */ #define CONFIG_SYS_OR7_PRELIM 0xFFF00000 #define CONFIG_SYS_BR7_PRELIM 0xF0700000 /* * Sanity checks */ #if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET) #error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured #endif #endif /* __CONFIG_H */