/* * Copyright 2007-2008 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * mpc8572ds board configuration file * */ #ifndef __CONFIG_H #define __CONFIG_H /* High Level Configuration Options */ #define CONFIG_BOOKE 1 /* BOOKE */ #define CONFIG_E500 1 /* BOOKE e500 family */ #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ #define CONFIG_MPC8572 1 #define CONFIG_MPC8572DS 1 #define CONFIG_MP 1 /* support multiple processors */ #define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */ #define CONFIG_PCI 1 /* Enable PCI/PCIE */ #define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */ #define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */ #define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */ #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE /* * When initializing flash, if we cannot find the manufacturer ID, * assume this is the AMD flash associated with the CDS board. * This allows booting from a promjet. */ #define CONFIG_ASSUME_AMD_FLASH #ifndef __ASSEMBLY__ extern unsigned long get_board_sys_clk(unsigned long dummy); extern unsigned long get_board_ddr_clk(unsigned long dummy); #endif #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ #define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */ #define CONFIG_GET_CLK_FROM_ICS307 /* decode sysclk and ddrclk freq from ICS307 instead of switches */ /* * These can be toggled for performance analysis, otherwise use default. */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_ENABLE_36BIT_PHYS 1 #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x7fffffff #define CONFIG_PANIC_HANG /* do not reset board on panic */ /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ #define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR+0x8000) #define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) #define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) /* DDR Setup */ #define CONFIG_FSL_DDR2 #undef CONFIG_FSL_DDR_INTERACTIVE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ #define CONFIG_DDR_SPD #undef CONFIG_DDR_DLL #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER #define CONFIG_MEM_INIT_VALUE 0xDeadBeef #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_NUM_DDR_CONTROLLERS 2 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 /* I2C addresses of SPD EEPROMs */ #define CONFIG_SYS_SPD_BUS_NUM 1 /* SPD EEPROMS locate on I2C bus 1 */ #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ #define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 1 DIMM 0 */ /* These are used when DDR doesn't use SPD. */ #define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */ #define CONFIG_SYS_DDR_CS0_BNDS 0x0000001F #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */ #define CONFIG_SYS_DDR_TIMING_3 0x00020000 #define CONFIG_SYS_DDR_TIMING_0 0x00260802 #define CONFIG_SYS_DDR_TIMING_1 0x626b2634 #define CONFIG_SYS_DDR_TIMING_2 0x062874cf #define CONFIG_SYS_DDR_MODE_1 0x00440462 #define CONFIG_SYS_DDR_MODE_2 0x00000000 #define CONFIG_SYS_DDR_INTERVAL 0x0c300100 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef #define CONFIG_SYS_DDR_CLK_CTRL 0x00800000 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 #define CONFIG_SYS_DDR_CONTROL 0xc3000008 /* Type = DDR2 */ #define CONFIG_SYS_DDR_CONTROL2 0x24400000 #define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d #define CONFIG_SYS_DDR_ERR_DIS 0x00000000 #define CONFIG_SYS_DDR_SBE 0x00010000 /* * Make sure required options are set */ #ifndef CONFIG_SPD_EEPROM #error ("CONFIG_SPD_EEPROM is required") #endif #undef CONFIG_CLOCKS_IN_MHZ /* * Memory map * * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable * * Localbus cacheable (TBD) * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable * * Localbus non-cacheable * 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable */ /* * Local Bus Definitions */ #define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */ #define CONFIG_SYS_BR0_PRELIM 0xe8001001 #define CONFIG_SYS_OR0_PRELIM 0xf8000ff7 #define CONFIG_SYS_BR1_PRELIM 0xe0001001 #define CONFIG_SYS_OR1_PRELIM 0xf8000ff7 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE + 0x8000000, CONFIG_SYS_FLASH_BASE} #define CONFIG_SYS_FLASH_QUIET_TEST #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ #undef CONFIG_SYS_FLASH_CHECKSUM #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_EMPTY_INFO #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ #define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ #define CONFIG_SYS_BR3_PRELIM (PIXIS_BASE | 0x0801) /* port size 8bit */ #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ #define PIXIS_ID 0x0 /* Board ID at offset 0 */ #define PIXIS_VER 0x1 /* Board version at offset 1 */ #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ #define PIXIS_CSR 0x3 /* PIXIS General control/status register */ #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ #define PIXIS_PWR 0x5 /* PIXIS Power status register */ #define PIXIS_AUX 0x6 /* Auxiliary 1 register */ #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ #define PIXIS_AUX2 0x8 /* Auxiliary 2 register */ #define PIXIS_VCTL 0x10 /* VELA Control Register */ #define PIXIS_VSTAT 0x11 /* VELA Status Register */ #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ #define PIXIS_VCORE0 0x14 /* VELA VCORE0 Register */ #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ #define PIXIS_VSPEED2 0x19 /* VELA VSpeed 2 */ #define PIXIS_VSYSCLK0 0x1C /* VELA SYSCLK0 Register */ #define PIXIS_VSYSCLK1 0x1D /* VELA SYSCLK1 Register */ #define PIXIS_VSYSCLK2 0x1E /* VELA SYSCLK2 Register */ #define PIXIS_VDDRCLK0 0x1F /* VELA DDRCLK0 Register */ #define PIXIS_VDDRCLK1 0x20 /* VELA DDRCLK1 Register */ #define PIXIS_VDDRCLK2 0x21 /* VELA DDRCLK2 Register */ #define PIXIS_VWATCH 0x24 /* Watchdog Register */ #define PIXIS_LED 0x25 /* LED Register */ /* old pixis referenced names */ #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ #define CONFIG_SYS_PIXIS_VBOOT_MASK 0xc0 #define PIXIS_VSPEED2_TSEC1SER 0x8 #define PIXIS_VSPEED2_TSEC2SER 0x4 #define PIXIS_VSPEED2_TSEC3SER 0x2 #define PIXIS_VSPEED2_TSEC4SER 0x1 #define PIXIS_VCFGEN1_TSEC1SER 0x20 #define PIXIS_VCFGEN1_TSEC2SER 0x20 #define PIXIS_VCFGEN1_TSEC3SER 0x20 #define PIXIS_VCFGEN1_TSEC4SER 0x20 #define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER \ | PIXIS_VSPEED2_TSEC2SER \ | PIXIS_VSPEED2_TSEC3SER \ | PIXIS_VSPEED2_TSEC4SER) #define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER \ | PIXIS_VCFGEN1_TSEC2SER \ | PIXIS_VCFGEN1_TSEC3SER \ | PIXIS_VCFGEN1_TSEC4SER) #define CONFIG_SYS_INIT_RAM_LOCK 1 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ #define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */ #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ #define CONFIG_SYS_NAND_BASE 0xffa00000 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE,\ CONFIG_SYS_NAND_BASE + 0x40000, \ CONFIG_SYS_NAND_BASE + 0x80000,\ CONFIG_SYS_NAND_BASE + 0xC0000} #define CONFIG_SYS_MAX_NAND_DEVICE 4 #define NAND_MAX_CHIPS 1 #define CONFIG_MTD_NAND_VERIFY_WRITE #define CONFIG_CMD_NAND 1 #define CONFIG_NAND_FSL_ELBC 1 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) /* NAND flash config */ #define CONFIG_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ | (2< " #endif /* * Pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 #define CONFIG_SYS_64BIT_VSPRINTF 1 #define CONFIG_SYS_64BIT_STRTOUL 1 /* new uImage format support */ #define CONFIG_FIT 1 #define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ /* I2C */ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_I2C_MULTI_BUS #define CONFIG_I2C_CMD_TREE #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 #define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_SYS_I2C_NOPROBES {{0,0x29}}/* Don't probe these addrs */ #define CONFIG_SYS_I2C_OFFSET 0x3000 #define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * I2C2 EEPROM */ #define CONFIG_ID_EEPROM #ifdef CONFIG_ID_EEPROM #define CONFIG_SYS_I2C_EEPROM_NXID #endif #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 #define CONFIG_SYS_EEPROM_BUS_NUM 1 /* * General PCI * Memory space is mapped 1-1, but I/O space must start from 0. */ /* controller 3, direct to uli, tgtid 3, Base address 8000 */ #define CONFIG_SYS_PCIE3_MEM_BASE 0x80000000 #define CONFIG_SYS_PCIE3_MEM_PHYS CONFIG_SYS_PCIE3_MEM_BASE #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCIE3_IO_BASE 0x00000000 #define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ /* controller 2, Slot 2, tgtid 2, Base address 9000 */ #define CONFIG_SYS_PCIE2_MEM_BASE 0xa0000000 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BASE #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ /* controller 1, Slot 1, tgtid 1, Base address a000 */ #define CONFIG_SYS_PCIE1_MEM_BASE 0xc0000000 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ #if defined(CONFIG_PCI) /*PCIE video card used*/ #define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_PHYS /* video */ #define CONFIG_VIDEO #if defined(CONFIG_VIDEO) #define CONFIG_BIOSEMU #define CONFIG_CFB_CONSOLE #define CONFIG_VIDEO_SW_CURSOR #define CONFIG_VGA_AS_SINGLE_DEVICE #define CONFIG_ATI_RADEON_FB #define CONFIG_VIDEO_LOGO /*#define CONFIG_CONSOLE_CURSOR*/ #define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET #endif #define CONFIG_NET_MULTI #define CONFIG_PCI_PNP /* do pci plug-and-play */ #undef CONFIG_EEPRO100 #undef CONFIG_TULIP #undef CONFIG_RTL8139 #ifdef CONFIG_RTL8139 /* This macro is used by RTL8139 but not defined in PPC architecture */ #define KSEG1ADDR(x) (x) #define _IO_BASE 0x00000000 #endif #ifndef CONFIG_PCI_PNP #define PCI_ENET0_IOADDR CONFIG_SYS_PCIE3_IO_BASE #define PCI_ENET0_MEMADDR CONFIG_SYS_PCIE3_IO_BASE #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */ #endif #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CONFIG_DOS_PARTITION #define CONFIG_SCSI_AHCI #ifdef CONFIG_SCSI_AHCI #define CONFIG_SATA_ULI5288 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 #define CONFIG_SYS_SCSI_MAX_LUN 1 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) #define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE #endif /* SCSI */ #endif /* CONFIG_PCI */ #if defined(CONFIG_TSEC_ENET) #ifndef CONFIG_NET_MULTI #define CONFIG_NET_MULTI 1 #endif #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ #define CONFIG_TSEC1 1 #define CONFIG_TSEC1_NAME "eTSEC1" #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "eTSEC2" #define CONFIG_TSEC3 1 #define CONFIG_TSEC3_NAME "eTSEC3" #define CONFIG_TSEC4 1 #define CONFIG_TSEC4_NAME "eTSEC4" #define CONFIG_PIXIS_SGMII_CMD #define CONFIG_FSL_SGMII_RISER 1 #define SGMII_RISER_PHY_OFFSET 0x1c #ifdef CONFIG_FSL_SGMII_RISER #define CONFIG_SYS_TBIPA_VALUE 0x10 /* avoid conflict with eTSEC4 paddr */ #endif #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC3_PHY_ADDR 2 #define TSEC4_PHY_ADDR 3 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define TSEC3_PHYIDX 0 #define TSEC4_PHYIDX 0 #define CONFIG_ETHPRIME "eTSEC1" #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #endif /* CONFIG_TSEC_ENET */ /* * Environment */ #define CONFIG_ENV_IS_IN_FLASH 1 #if CONFIG_SYS_MONITOR_BASE > 0xfff80000 #define CONFIG_ENV_ADDR 0xfff80000 #else #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) #endif #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* * Command line configuration. */ #include #define CONFIG_CMD_IRQ #define CONFIG_CMD_PING #define CONFIG_CMD_I2C #define CONFIG_CMD_MII #define CONFIG_CMD_ELF #define CONFIG_CMD_IRQ #define CONFIG_CMD_SETEXPR #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI #define CONFIG_CMD_BEDBUG #define CONFIG_CMD_NET #define CONFIG_CMD_SCSI #define CONFIG_CMD_EXT2 #endif #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_CMDLINE_EDITING /* Command-line editing */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /* * Environment Configuration */ /* The mac addresses for all ethernet interface */ #if defined(CONFIG_TSEC_ENET) #define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:E0:0C:02:00:FD #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:E0:0C:02:01:FD #define CONFIG_HAS_ETH2 #define CONFIG_ETH2ADDR 00:E0:0C:02:02:FD #define CONFIG_HAS_ETH3 #define CONFIG_ETH3ADDR 00:E0:0C:02:03:FD #endif #define CONFIG_IPADDR 192.168.1.254 #define CONFIG_HOSTNAME unknown #define CONFIG_ROOTPATH /opt/nfsroot #define CONFIG_BOOTFILE uImage #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ #define CONFIG_SERVERIP 192.168.1.1 #define CONFIG_GATEWAYIP 192.168.1.1 #define CONFIG_NETMASK 255.255.255.0 /* default location for tftp and bootm */ #define CONFIG_LOADADDR 1000000 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #define CONFIG_BAUDRATE 115200 #define CONFIG_EXTRA_ENV_SETTINGS \ "memctl_intlv_ctl=2\0" \ "netdev=eth0\0" \ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ "tftpflash=tftpboot $loadaddr $uboot; " \ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ "erase " MK_STR(TEXT_BASE) " +$filesize; " \ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ "consoledev=ttyS0\0" \ "ramdiskaddr=2000000\0" \ "ramdiskfile=8572ds/ramdisk.uboot\0" \ "fdtaddr=c00000\0" \ "fdtfile=8572ds/mpc8572ds.dtb\0" \ "bdev=sda3\0" #define CONFIG_HDBOOT \ "setenv bootargs root=/dev/$bdev rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr - $fdtaddr" #define CONFIG_NFSBOOTCOMMAND \ "setenv bootargs root=/dev/nfs rw " \ "nfsroot=$serverip:$rootpath " \ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr - $fdtaddr" #define CONFIG_RAMBOOTCOMMAND \ "setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $ramdiskaddr $ramdiskfile;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr $ramdiskaddr $fdtaddr" #define CONFIG_BOOTCOMMAND CONFIG_HDBOOT #endif /* __CONFIG_H */