/* * Copyright 2004 Freescale Semiconductor. * (C) Copyright 2002,2003 Motorola,Inc. * Xianghua Xiao * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * mpc8540ads board configuration file * * Please refer to doc/README.mpc85xx for more info. * * Make sure you change the MAC address and other network params first, * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. */ #ifndef __CONFIG_H #define __CONFIG_H /* High Level Configuration Options */ #define CONFIG_BOOKE 1 /* BOOKE */ #define CONFIG_E500 1 /* BOOKE e500 family */ #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ #define CONFIG_MPC8540 1 /* MPC8540 specific */ #define CONFIG_MPC8540ADS 1 /* MPC8540ADS board specific */ #ifndef CONFIG_HAS_FEC #define CONFIG_HAS_FEC 1 /* 8540 has FEC */ #endif #define CONFIG_PCI #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ /* * sysclk for MPC85xx * * Two valid values are: * 33000000 * 66000000 * * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz * is likely the desired value here, so that is now the default. * The board, however, can run at 66MHz. In any event, this value * must match the settings of some switches. Details can be found * in the README.mpc85xxads. * * XXX -- Can't we run at 66 MHz, anyway? PCI should drop to * 33MHz to accommodate, based on a PCI pin. * Note that PCI-X won't work at 33MHz. */ #ifndef CONFIG_SYS_CLK_FREQ #define CONFIG_SYS_CLK_FREQ 33000000 #endif /* * These can be toggled for performance analysis, otherwise use default. */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ #define CONFIG_SYS_MEMTEST_END 0x00400000 /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ /* DDR Setup */ #define CONFIG_FSL_DDR1 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ #define CONFIG_DDR_SPD #undef CONFIG_FSL_DDR_INTERACTIVE #define CONFIG_MEM_INIT_VALUE 0xDeadBeef #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_NUM_DDR_CONTROLLERS 1 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) /* I2C addresses of SPD EEPROMs */ #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ /* These are used when DDR doesn't use SPD. */ #define CONFIG_SYS_SDRAM_SIZE 128 /* DDR is 128MB */ #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ #define CONFIG_SYS_DDR_CS0_CONFIG 0x80000002 #define CONFIG_SYS_DDR_TIMING_1 0x37344321 #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ #define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ #define CONFIG_SYS_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */ #define CONFIG_SYS_DDR_INTERVAL 0x05200100 /* autocharge,no open page */ /* * SDRAM on the Local Bus */ #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ #define CONFIG_SYS_BR0_PRELIM 0xff001801 /* port size 32bit */ #define CONFIG_SYS_OR0_PRELIM 0xff006ff7 /* 16MB Flash */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ #define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */ #undef CONFIG_SYS_FLASH_CHECKSUM #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) #define CONFIG_SYS_RAMBOOT #else #undef CONFIG_SYS_RAMBOOT #endif #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_EMPTY_INFO #undef CONFIG_CLOCKS_IN_MHZ /* * Local Bus Definitions */ /* * Base Register 2 and Option Register 2 configure SDRAM. * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. * * For BR2, need: * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 * port-size = 32-bits = BR2[19:20] = 11 * no parity checking = BR2[21:22] = 00 * SDRAM for MSEL = BR2[24:26] = 011 * Valid = BR[31] = 1 * * 0 4 8 12 16 20 24 28 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 * * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into * FIXME: the top 17 bits of BR2. */ #define CONFIG_SYS_BR2_PRELIM 0xf0001861 /* * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. * * For OR2, need: * 64MB mask for AM, OR2[0:7] = 1111 1100 * XAM, OR2[17:18] = 11 * 9 columns OR2[19-21] = 010 * 13 rows OR2[23-25] = 100 * EAD set for extra time OR[31] = 1 * * 0 4 8 12 16 20 24 28 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 */ #define CONFIG_SYS_OR2_PRELIM 0xfc006901 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/ /* * LSDMR masks */ #define CONFIG_SYS_LBC_LSDMR_RFEN (1 << (31 - 1)) #define CONFIG_SYS_LBC_LSDMR_BSMA1516 (3 << (31 - 10)) #define CONFIG_SYS_LBC_LSDMR_BSMA1617 (4 << (31 - 10)) #define CONFIG_SYS_LBC_LSDMR_RFCR5 (3 << (31 - 16)) #define CONFIG_SYS_LBC_LSDMR_RFCR16 (7 << (31 - 16)) #define CONFIG_SYS_LBC_LSDMR_PRETOACT3 (3 << (31 - 19)) #define CONFIG_SYS_LBC_LSDMR_PRETOACT7 (7 << (31 - 19)) #define CONFIG_SYS_LBC_LSDMR_ACTTORW3 (3 << (31 - 22)) #define CONFIG_SYS_LBC_LSDMR_ACTTORW7 (7 << (31 - 22)) #define CONFIG_SYS_LBC_LSDMR_ACTTORW6 (6 << (31 - 22)) #define CONFIG_SYS_LBC_LSDMR_BL8 (1 << (31 - 23)) #define CONFIG_SYS_LBC_LSDMR_WRC2 (2 << (31 - 27)) #define CONFIG_SYS_LBC_LSDMR_WRC4 (0 << (31 - 27)) #define CONFIG_SYS_LBC_LSDMR_BUFCMD (1 << (31 - 29)) #define CONFIG_SYS_LBC_LSDMR_CL3 (3 << (31 - 31)) #define CONFIG_SYS_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) #define CONFIG_SYS_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) #define CONFIG_SYS_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) #define CONFIG_SYS_LBC_LSDMR_OP_MRW (3 << (31 - 4)) #define CONFIG_SYS_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) #define CONFIG_SYS_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) #define CONFIG_SYS_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) #define CONFIG_SYS_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) #define CONFIG_SYS_LBC_LSDMR_COMMON ( CONFIG_SYS_LBC_LSDMR_BSMA1516 \ | CONFIG_SYS_LBC_LSDMR_RFCR5 \ | CONFIG_SYS_LBC_LSDMR_PRETOACT3 \ | CONFIG_SYS_LBC_LSDMR_ACTTORW3 \ | CONFIG_SYS_LBC_LSDMR_BL8 \ | CONFIG_SYS_LBC_LSDMR_WRC2 \ | CONFIG_SYS_LBC_LSDMR_CL3 \ | CONFIG_SYS_LBC_LSDMR_RFEN \ ) /* * SDRAM Controller configuration sequence. */ #define CONFIG_SYS_LBC_LSDMR_1 ( CONFIG_SYS_LBC_LSDMR_COMMON \ | CONFIG_SYS_LBC_LSDMR_OP_PCHALL) #define CONFIG_SYS_LBC_LSDMR_2 ( CONFIG_SYS_LBC_LSDMR_COMMON \ | CONFIG_SYS_LBC_LSDMR_OP_ARFRSH) #define CONFIG_SYS_LBC_LSDMR_3 ( CONFIG_SYS_LBC_LSDMR_COMMON \ | CONFIG_SYS_LBC_LSDMR_OP_ARFRSH) #define CONFIG_SYS_LBC_LSDMR_4 ( CONFIG_SYS_LBC_LSDMR_COMMON \ | CONFIG_SYS_LBC_LSDMR_OP_MRW) #define CONFIG_SYS_LBC_LSDMR_5 ( CONFIG_SYS_LBC_LSDMR_COMMON \ | CONFIG_SYS_LBC_LSDMR_OP_NORMAL) /* * 32KB, 8-bit wide for ADS config reg */ #define CONFIG_SYS_BR4_PRELIM 0xf8000801 #define CONFIG_SYS_OR4_PRELIM 0xffffe1f1 #define CONFIG_SYS_BCSR (CONFIG_SYS_BR4_PRELIM & 0xffff8000) #define CONFIG_SYS_INIT_RAM_LOCK 1 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) /* Use the HUSH parser */ #define CONFIG_SYS_HUSH_PARSER #ifdef CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 #define CONFIG_SYS_64BIT_VSPRINTF 1 #define CONFIG_SYS_64BIT_STRTOUL 1 /* * I2C */ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ #define CONFIG_SYS_I2C_OFFSET 0x3000 /* RapidIO MMU */ #define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 /* base address */ #define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE #define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */ /* * General PCI * Memory space is mapped 1-1, but I/O space must start from 0. */ #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ #if defined(CONFIG_PCI) #define CONFIG_NET_MULTI #define CONFIG_PCI_PNP /* do pci plug-and-play */ #undef CONFIG_EEPRO100 #undef CONFIG_TULIP #if !defined(CONFIG_PCI_PNP) #define PCI_ENET0_IOADDR 0xe0000000 #define PCI_ENET0_MEMADDR 0xe0000000 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ #endif #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ #endif /* CONFIG_PCI */ #if defined(CONFIG_TSEC_ENET) #ifndef CONFIG_NET_MULTI #define CONFIG_NET_MULTI 1 #endif #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_TSEC1 1 #define CONFIG_TSEC1_NAME "TSEC0" #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "TSEC1" #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define TSEC1_FLAGS TSEC_GIGABIT #define TSEC2_FLAGS TSEC_GIGABIT #if CONFIG_HAS_FEC #define CONFIG_MPC85XX_FEC 1 #define CONFIG_MPC85XX_FEC_NAME "FEC" #define FEC_PHY_ADDR 3 #define FEC_PHYIDX 0 #define FEC_FLAGS 0 #endif /* Options are: TSEC[0-1], FEC */ #define CONFIG_ETHPRIME "TSEC0" #endif /* CONFIG_TSEC_ENET */ /* * Environment */ #ifndef CONFIG_SYS_RAMBOOT #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ #define CONFIG_ENV_SIZE 0x2000 #else #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 #endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include #define CONFIG_CMD_PING #define CONFIG_CMD_I2C #define CONFIG_CMD_ELF #define CONFIG_CMD_IRQ #define CONFIG_CMD_SETEXPR #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI #endif #if defined(CONFIG_SYS_RAMBOOT) #undef CONFIG_CMD_ENV #undef CONFIG_CMD_LOADS #endif #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_CMDLINE_EDITING /* Command-line editing */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /* * Environment Configuration */ /* The mac addresses for all ethernet interface */ #if defined(CONFIG_TSEC_ENET) #define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD #define CONFIG_HAS_ETH2 #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD #endif #define CONFIG_IPADDR 192.168.1.253 #define CONFIG_HOSTNAME unknown #define CONFIG_ROOTPATH /nfsroot #define CONFIG_BOOTFILE your.uImage #define CONFIG_SERVERIP 192.168.1.1 #define CONFIG_GATEWAYIP 192.168.1.1 #define CONFIG_NETMASK 255.255.255.0 #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #define CONFIG_BAUDRATE 115200 #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "consoledev=ttyS0\0" \ "ramdiskaddr=1000000\0" \ "ramdiskfile=your.ramdisk.u-boot\0" \ "fdtaddr=400000\0" \ "fdtfile=your.fdt.dtb\0" #define CONFIG_NFSBOOTCOMMAND \ "setenv bootargs root=/dev/nfs rw " \ "nfsroot=$serverip:$rootpath " \ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr - $fdtaddr" #define CONFIG_RAMBOOTCOMMAND \ "setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $ramdiskaddr $ramdiskfile;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr $ramdiskaddr $fdtaddr" #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND #endif /* __CONFIG_H */