TABILITY or FITNESS FO04-2007 Freescale Semiconductor, Inc. * Hayden Fraser (Hayden.Fraser@freescale.com) * * SPDX-License-Identifier: GPL-2.0+ */ #ifndef _M5253DEMO_H #define _M5253DEMO_H #define CONFIG_MCF52x2 /* define processor family */ #define CONFIG_M5253 /* define processor type */ #define CONFIG_M5253DEMO /* define board type */ #define CONFIG_MCFTMR #define CONFIG_MCFUART #define CONFIG_SYS_UART_PORT (0) #define CONFIG_BAUDRATE 115200 #undef CONFIG_WATCHDOG /* disable watchdog */ #define CONFIG_BOOTDELAY 5 /* Configuration for environment * Environment is embedded in u-boot in the second sector of the flash */ #ifdef CONFIG_MONITOR_IS_IN_RAM # define CONFIG_ENV_OFFSET 0x4000 # define CONFIG_ENV_SECT_SIZE 0x1000 # define CONFIG_ENV_IS_IN_FLASH 1 #else # define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x4000) # define CONFIG_ENV_SECT_SIZE 0x1000 # define CONFIG_ENV_IS_IN_FLASH 1 #endif /* * Command line configuration. */ #include #define CONFIG_CMD_CACHE #define CONFIG_CMD_LOADB #define CONFIG_CMD_LOADS #define CONFIG_CMD_EXT2 #define CONFIG_CMD_FAT #define CONFIG_CMD_IDE #define CONFIG_CMD_MEMORY #define CONFIG_CMD_MISC #define CONFIG_CMD_PING #ifdef CONFIG_CMD_IDE /* ATA */ # define CONFIG_DOS_PARTITION # define CONFIG_MAC_PARTITION # define CONFIG_IDE_RESET 1 # define CONFIG_IDE_PREINIT 1 # define CONFIG_ATAPI # undef CONFIG_LBA48 # define CONFIG_SYS_IDE_MAXBUS 1 # define CONFIG_SYS_IDE_MAXDEVICE 2 # define CONFIG_SYS_ATA_BASE_ADDR (CONFIG_SYS_MBAR2 + 0x800) # define CONFIG_SYS_ATA_IDE0_OFFSET 0 # define CONFIG_SYS_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */ # define CONFIG_SYS_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */ # define CONFIG_SYS_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */ # define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ #endif #define CONFIG_DRIVER_DM9000 #ifdef CONFIG_DRIVER_DM9000 # define CONFIG_DM9000_BASE (CONFIG_SYS_CS1_BASE | 0x300) # define DM9000_IO CONFIG_DM9000_BASE # define DM9000_DATA (CONFIG_DM9000_BASE + 4) # undef CONFIG_DM9000_DEBUG # define CONFIG_DM9000_BYTE_SWAPPED # define CONFIG_OVERWRITE_ETHADDR_ONCE # define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ "loadaddr=10000\0" \ "u-boot=u-boot.bin\0" \ "load=tftp ${loadaddr) ${u-boot}\0" \ "upd=run load; run prog\0" \ "prog=prot off 0xff800000 0xff82ffff;" \ "era 0xff800000 0xff82ffff;" \ "cp.b ${loadaddr} 0xff800000 ${filesize};" \ "save\0" \ "" #endif #define CONFIG_HOSTNAME M5253DEMO /* I2C */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_FSL #define CONFIG_SYS_FSL_I2C_SPEED 80000 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F #define CONFIG_SYS_FSL_I2C_OFFSET 0x00000280 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_SYS_I2C_PINMUX_REG (*(u32 *) (CONFIG_SYS_MBAR+0x19C)) #define CONFIG_SYS_I2C_PINMUX_CLR (0xFFFFE7FF) #define CONFIG_SYS_I2C_PINMUX_SET (0) #define CONFIG_SYS_PROMPT "=> " #define CONFIG_SYS_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) # define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else # define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_LOAD_ADDR 0x00100000 #define CONFIG_SYS_MEMTEST_START 0x400 #define CONFIG_SYS_MEMTEST_END 0x380000 #define CONFIG_SYS_HZ 1000 #undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ #define CONFIG_SYS_FAST_CLK #ifdef CONFIG_SYS_FAST_CLK # define CONFIG_SYS_PLLCR 0x1243E054 # define CONFIG_SYS_CLK 140000000 #else # define CONFIG_SYS_PLLCR 0x135a4140 # define CONFIG_SYS_CLK 70000000 #endif /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ #define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ #define CONFIG_SYS_MBAR2 0x80000000 /* Module Base Addrs 2 */ /* * Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 #define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ #ifdef CONFIG_MONITOR_IS_IN_RAM # define CONFIG_SYS_MONITOR_BASE 0x20000 #else # define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) #endif #define CONFIG_SYS_MONITOR_LEN 0x40000 #define CONFIG_SYS_MALLOC_LEN (256 << 10) #define CONFIG_SYS_BOOTPARAMS_LEN (64*1024) /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) #define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20) /* FLASH organization */ #define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE) #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 2048 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 1000 #define FLASH_SST6401B 0x200 #define SST_ID_xF6401B 0x236D236D #undef CONFIG_SYS_FLASH_CFI #ifdef CONFIG_SYS_FLASH_CFI /* * Unable to use CFI driver, due to incompatible sector erase command by SST. * Amd/Atmel use 0x30 for sector erase, SST use 0x50. * 0x30 is block erase in SST */ # define CONFIG_FLASH_CFI_DRIVER 1 # define CONFIG_SYS_FLASH_SIZE 0x800000 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT # define CONFIG_FLASH_CFI_LEGACY #else # define CONFIG_SYS_SST_SECT 2048 # define CONFIG_SYS_SST_SECTSZ 0x1000 # define CONFIG_SYS_FLASH_WRITE_TOUT 500 #endif /* Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ CONFIG_SYS_INIT_RAM_SIZE - 8) #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ CONFIG_SYS_INIT_RAM_SIZE - 4) #define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \ CF_ADDRMASK(8) | \ CF_ACR_EN | CF_ACR_SM_ALL) #define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ CF_ACR_EN | CF_ACR_SM_ALL) #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ CF_CACR_DBWE) /* Port configuration */ #define CONFIG_SYS_FECI2C 0xF0 #define CONFIG_SYS_CS0_BASE 0xFF800000 #define CONFIG_SYS_CS0_MASK 0x007F0021 #define CONFIG_SYS_CS0_CTRL 0x00001D80 #define CONFIG_SYS_CS1_BASE 0xE0000000 #define CONFIG_SYS_CS1_MASK 0x00000001 #define CONFIG_SYS_CS1_CTRL 0x00003DD8 /*----------------------------------------------------------------------- * Port configuration */ #define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ #define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */ #define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */ #define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */ #define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */ #define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ #define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */ #endif /* _M5253DEMO_H */