/* * (C) Copyright 2004 Sandburst Corporation * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /************************************************************************ * KAMINOREFDES.h - configuration for the Sandburst Kamino Reference * design. ***********************************************************************/ /* * $Id: KAREF.h,v 1.6 2005/06/03 15:05:25 tsawyer Exp $ * */ #ifndef __CONFIG_H #define __CONFIG_H /*----------------------------------------------------------------------- * High Level Configuration Options *----------------------------------------------------------------------*/ #define CONFIG_KAREF 1 /* Board is Kamino Ref Variant */ #define CONFIG_440GX 1 /* Specifc GX support */ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_MISC_INIT_F 1 /* Call board misc_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call board misc_init_r */ #undef CONFIG_SYS_DRAM_TEST /* Disable-takes long time!*/ #define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ #define CONFIG_VERY_BIG_RAM 1 #define CONFIG_VERSION_VARIABLE #define CONFIG_IDENT_STRING " Sandburst Kamino Reference Design" /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ #define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */ #define CONFIG_SYS_MONITOR_BASE 0xfff80000 /* start of monitor */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ #define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000) #define CONFIG_SYS_KAREF_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08200000) #define CONFIG_SYS_OFEM_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08400000) #define CONFIG_SYS_BME32_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08500000) #define CONFIG_SYS_GPIO_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700) /* Here for completeness */ #define CONFIG_SYS_OFEMAC_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08600000) /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ #define CONFIG_SYS_TEMP_STACK_OCM 1 #define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */ #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Rsrv 256kB for Mon */ #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Rsrv 128kB for malloc */ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #define CONFIG_CONS_INDEX 1 /* Use UART0 */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_serial_clock() #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SERIAL_MULTI 1 #define CONFIG_BAUDRATE 9600 #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * NVRAM/RTC * * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located. * The DS1743 code assumes this condition (i.e. -- it assumes the base * address for the RTC registers is: * * CONFIG_SYS_NVRAM_BASE_ADDR + CONFIG_SYS_NVRAM_SIZE * *----------------------------------------------------------------------*/ #define CONFIG_SYS_NVRAM_SIZE (0x2000 - 8) /* NVRAM size(8k)- RTC regs*/ #define CONFIG_RTC_DS174x 1 /* DS1743 RTC */ /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ #define CONFIG_SYS_MAX_FLASH_SECT 8 /* sectors per device */ #undef CONFIG_SYS_FLASH_CHECKSUM #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Flash Erase TO (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO(in ms) */ /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ #define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup*/ #define SPD_EEPROM_ADDRESS {0x53} /* SPD i2c spd addresses */ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ #define CONFIG_HARD_I2C 1 /* I2C hardware support */ #undef CONFIG_SOFT_I2C /* I2C !bit-banged */ #define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed 400kHz */ #define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */ #define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ #define CONFIG_I2C_BUS1 1 /* Include i2c bus 1 supp */ /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ #define CONFIG_ENV_IS_IN_NVRAM 1 /* Environment uses NVRAM */ #undef CONFIG_ENV_IS_IN_FLASH /* ... not in flash */ #undef CONFIG_ENV_IS_IN_EEPROM /* ... not in EEPROM */ #define CONFIG_ENV_OVERWRITE 1 /* allow env overwrite */ #define CONFIG_ENV_SIZE 0x1000 /* Size of Env vars */ #define CONFIG_ENV_ADDR (CONFIG_SYS_NVRAM_BASE_ADDR) #define CONFIG_BOOTDELAY 5 /* 5 second autoboot */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial dnld */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /*----------------------------------------------------------------------- * Networking *----------------------------------------------------------------------*/ #define CONFIG_PPC4xx_EMAC #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_NET_MULTI 1 #define CONFIG_PHY_ADDR 0xff /* no phy on EMAC0 */ #define CONFIG_PHY1_ADDR 0xff /* no phy on EMAC1 */ #define CONFIG_PHY2_ADDR 0x08 /* PHY addr, MGMT, EMAC2 */ #define CONFIG_PHY3_ADDR 0x18 /* PHY addr, LCL, EMAC3 */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_HAS_ETH2 #define CONFIG_HAS_ETH3 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_CIS8201_PHY 1 /* RGMII mode for Cicada */ #define CONFIG_CIS8201_SHORT_ETCH 1 /* Use short etch mode */ #define CONFIG_PHY_GIGE 1 /* GbE speed/duplex detect */ #define CONFIG_PHY_RESET_DELAY 1000 #define CONFIG_NETMASK 255.255.0.0 #define CONFIG_ETHADDR 00:00:00:00:00:00 /* No EMAC 0 support */ #define CONFIG_ETH1ADDR 00:00:00:00:00:00 /* No EMAC 1 support */ #define CONFIG_SYS_RX_ETH_BUFFER 32 /* #eth rx buff & descrs */ /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include #define CONFIG_CMD_PCI #define CONFIG_CMD_IRQ #define CONFIG_CMD_I2C #define CONFIG_CMD_DHCP #define CONFIG_CMD_DATE #define CONFIG_CMD_BEDBUG #define CONFIG_CMD_PING #define CONFIG_CMD_DIAG #define CONFIG_CMD_MII #define CONFIG_CMD_NET #define CONFIG_CMD_ELF #define CONFIG_CMD_IDE #define CONFIG_CMD_FAT /* Include NetConsole support */ #define CONFIG_NETCONSOLE /* Include auto complete with tabs */ #define CONFIG_AUTO_COMPLETE 1 #define CONFIG_SYS_ALT_MEMTEST 1 /* use real memory test */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "KaRefDes=> " /* Monitor Command Prompt */ #define CONFIG_SYS_HUSH_PARSER 1 /* HUSH for ext'd cli */ #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /*----------------------------------------------------------------------- * Console Buffer *----------------------------------------------------------------------*/ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg Buffer Size */ /*----------------------------------------------------------------------- * Memory Test *----------------------------------------------------------------------*/ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ /*----------------------------------------------------------------------- * Compact Flash (in true IDE mode) *----------------------------------------------------------------------*/ #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ #undef CONFIG_IDE_LED /* no led for ide supported */ #define CONFIG_IDE_RESET /* reset for ide supported */ #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ #define CONFIG_SYS_ATA_BASE_ADDR 0xF0000000 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 #define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ #define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses*/ #define CONFIG_SYS_ATA_ALT_OFFSET 0x100000 /* Offset for alternate registers */ #define CONFIG_SYS_ATA_STRIDE 2 /* Directly connected CF, needs a stride to get to the correct offset */ #define CONFIG_DOS_PARTITION 1 /* Include dos partition */ /*----------------------------------------------------------------------- * PCI *----------------------------------------------------------------------*/ /* General PCI */ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices */ #define CONFIG_SYS_PCI_TARGBASE (CONFIG_SYS_PCI_MEMBASE) /* Board-specific PCI */ #define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target*/ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x17BA /* Sandburst */ #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal PowerOn: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* kgdb serial port baud */ #define CONFIG_KGDB_SER_INDEX 2 /* kgdb serial port */ #endif /*----------------------------------------------------------------------- * Miscellaneous configurable options *----------------------------------------------------------------------*/ #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_SYS_LOAD_ADDR 0x8000000 /* default load address */ #define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info */ #define CONFIG_SYS_HZ 100 /* decr freq: 1 ms ticks */ #endif /* __CONFIG_H */