/* * (C) Copyright 2000-2005 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * SPDX-License-Identifier: GPL-2.0+ */ /* * board/config.h - configuration options, board specific */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_MPC860 1 /* This is a MPC860 CPU */ #define CONFIG_IP860 1 /* ...on a IP860 board */ #define CONFIG_SYS_TEXT_BASE 0x10000000 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ #define CONFIG_BAUDRATE 9600 #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" \ "\0load=tftp \"/tftpboot/u-boot.bin\"\0update=protect off 1:0;era 1:0;cp.b 100000 10000000 ${filesize}\0" #undef CONFIG_BOOTARGS #define CONFIG_BOOTCOMMAND \ "bootp; " \ "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ "bootm" #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ #undef CONFIG_WATCHDOG /* watchdog disabled */ /* enable I2C and select the hardware/software driver */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ #define CONFIG_SYS_I2C_SOFT_SPEED 50000 #define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ #define PB_SCL 0x00000020 /* PB 26 */ #define PB_SDA 0x00000010 /* PB 27 */ #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) #define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ else immr->im_cpm.cp_pbdat &= ~PB_SDA #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ # define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */ # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */ #define CONFIG_TIMESTAMP /* Print image info with timestamp */ /* * Command line configuration. */ #include #define CONFIG_CMD_BEDBUG #define CONFIG_CMD_I2C #define CONFIG_CMD_EEPROM #define CONFIG_CMD_NFS #define CONFIG_CMD_SNTP /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ #define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ /*----------------------------------------------------------------------- * Internal Memory Mapped Register */ #define CONFIG_SYS_IMMR 0xF1000000 /* Non-standard value!! */ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR #define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0x10000000 #ifdef DEBUG #define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ #else #if 0 /* need more space for I2C tests */ #define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ #else #define CONFIG_SYS_MONITOR_LEN (256 << 10) #endif #endif #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 124 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #undef CONFIG_ENV_IS_IN_FLASH #undef CONFIG_ENV_IS_IN_NVRAM #undef CONFIG_ENV_IS_IN_NVRAM #undef DEBUG_I2C #define CONFIG_ENV_IS_IN_EEPROM #ifdef CONFIG_ENV_IS_IN_NVRAM #define CONFIG_ENV_ADDR 0x20000000 /* use SRAM */ #define CONFIG_ENV_SIZE (16<<10) /* use 16 kB */ #endif /* CONFIG_ENV_IS_IN_NVRAM */ #ifdef CONFIG_ENV_IS_IN_EEPROM #define CONFIG_ENV_OFFSET 512 /* Leave 512 bytes free for other data */ #define CONFIG_ENV_SIZE 1536 /* Use remaining space */ #endif /* CONFIG_ENV_IS_IN_EEPROM */ /*----------------------------------------------------------------------- * Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ #endif #define CONFIG_SYS_DELAYED_ICACHE 1 /* enable ICache not before * running in RAM. */ /*----------------------------------------------------------------------- * SYPCR - System Protection Control 11-9 * SYPCR can only be written once after reset! *----------------------------------------------------------------------- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze * +0x0004 */ #if defined(CONFIG_WATCHDOG) #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) #else #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) #endif /*----------------------------------------------------------------------- * SIUMCR - SIU Module Configuration 11-6 *----------------------------------------------------------------------- * +0x0000 => 0x80600800 */ #define CONFIG_SYS_SIUMCR (SIUMCR_EARB | SIUMCR_EARP0 | \ SIUMCR_DBGC11 | SIUMCR_MLRC10) /*----------------------------------------------------------------------- * Clock Setting - get clock frequency from Board Revision Register *----------------------------------------------------------------------- */ #ifndef __ASSEMBLY__ extern unsigned long ip860_get_clk_freq (void); #endif #define CONFIG_8xx_GCLK_FREQ ip860_get_clk_freq() /*----------------------------------------------------------------------- * TBSCR - Time Base Status and Control 11-26 *----------------------------------------------------------------------- * Clear Reference Interrupt Status, Timebase freezing enabled * +0x0200 => 0x00C2 */ #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control 11-31 *----------------------------------------------------------------------- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled * +0x0240 => 0x0082 */ #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) /*----------------------------------------------------------------------- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 *----------------------------------------------------------------------- * Reset PLL lock status sticky bit, timer expired status bit and timer * interrupt status bit, set PLL multiplication factor ! */ /* +0x0286 => was: 0x0000D000 */ #define CONFIG_SYS_PLPRCR \ ( PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | \ /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \ PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \ ) /*----------------------------------------------------------------------- * SCCR - System Clock and reset Control Register 15-27 *----------------------------------------------------------------------- * Set clock output, timebase and RTC source and divider, * power management and some other internal clocks */ #define SCCR_MASK SCCR_EBDF11 #define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_TBS | \ SCCR_RTDIV | SCCR_RTSEL | \ /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \ SCCR_EBDF00 | SCCR_DFSYNC00 | \ SCCR_DFBRG00 | SCCR_DFNL000 | \ SCCR_DFNH000) /*----------------------------------------------------------------------- * RTCSC - Real-Time Clock Status and Control Register 11-27 *----------------------------------------------------------------------- */ /* +0x0220 => 0x00C3 */ #define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) /*----------------------------------------------------------------------- * RCCR - RISC Controller Configuration Register 19-4 *----------------------------------------------------------------------- */ /* +0x09C4 => TIMEP=1 */ #define CONFIG_SYS_RCCR 0x0100 /*----------------------------------------------------------------------- * RMDS - RISC Microcode Development Support Control Register *----------------------------------------------------------------------- */ #define CONFIG_SYS_RMDS 0 /*----------------------------------------------------------------------- * DER - Debug Event Register *----------------------------------------------------------------------- * */ #define CONFIG_SYS_DER 0 /* * Init Memory Controller: */ /* * MAMR settings for SDRAM - 16-14 * => 0xC3804114 */ /* periodic timer for refresh */ #define CONFIG_SYS_MAMR_PTA 0xC3 #define CONFIG_SYS_MAMR ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) /* * BR1 and OR1 (FLASH) */ #define FLASH_BASE 0x10000000 /* FLASH bank #0 */ /* used to re-map FLASH * restrict access enough to keep SRAM working (if any) * but not too much to meddle with FLASH accesses */ /* allow for max 8 MB of Flash */ #define CONFIG_SYS_REMAP_OR_AM 0xFF800000 /* OR addr mask */ #define CONFIG_SYS_PRELIM_OR_AM 0xFF800000 /* OR addr mask */ #define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | OR_SCY_6_CLK) #define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) #define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) /* 16 bit, bank valid */ #define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE & BR_BA_MSK) | BR_PS_32 | BR_V ) #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_BR0_PRELIM /* * BR2/OR2 - SDRAM */ #define SDRAM_BASE 0x00000000 /* SDRAM bank */ #define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */ #define SDRAM_TIMING 0x00000A00 /* SDRAM-Timing */ #define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */ #define CONFIG_SYS_OR2 (SDRAM_PRELIM_OR_AM | SDRAM_TIMING ) #define CONFIG_SYS_BR2 ((SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V ) /* * BR3/OR3 - SRAM (16 bit) */ #define SRAM_BASE 0x20000000 #define CONFIG_SYS_OR3 0xFFF00130 /* BI/SCY = 5/TRLX (internal) */ #define CONFIG_SYS_BR3 ((SRAM_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) #define SRAM_SIZE (1 + (~(CONFIG_SYS_OR3 & BR_BA_MSK))) #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR3 /* Make sure to map early */ #define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_BR3 /* in case it's used for ENV */ #define CONFIG_SYS_SRAM_BASE SRAM_BASE #define CONFIG_SYS_SRAM_SIZE SRAM_SIZE /* * BR4/OR4 - Board Control & Status (8 bit) */ #define BCSR_BASE 0xFC000000 #define CONFIG_SYS_OR4 0xFFFF0120 /* BI (internal) */ #define CONFIG_SYS_BR4 ((BCSR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) /* * BR5/OR5 - IP Slot A/B (16 bit) */ #define IP_SLOT_BASE 0x40000000 #define CONFIG_SYS_OR5 0xFE00010C /* SETA/TRLX/BI/ SCY=0 (external) */ #define CONFIG_SYS_BR5 ((IP_SLOT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) /* * BR6/OR6 - VME STD (16 bit) */ #define VME_STD_BASE 0xFE000000 #define CONFIG_SYS_OR6 0xFF00010C /* SETA/TRLX/BI/SCY=0 (external) */ #define CONFIG_SYS_BR6 ((VME_STD_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) /* * BR7/OR7 - SHORT I/O + RTC + IACK (16 bit) */ #define VME_SHORT_BASE 0xFF000000 #define CONFIG_SYS_OR7 0xFF00010C /* SETA/TRLX/BI/ SCY=0 (external) */ #define CONFIG_SYS_BR7 ((VME_SHORT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) /*----------------------------------------------------------------------- * Board Control and Status Region: *----------------------------------------------------------------------- */ #ifndef __ASSEMBLY__ typedef struct ip860_bcsr_s { unsigned char shmem_addr; /* +00 shared memory address register */ unsigned char reserved0; unsigned char mbox_addr; /* +02 mailbox address register */ unsigned char reserved1; unsigned char vme_int_mask; /* +04 VME Bus interrupt mask register */ unsigned char reserved2; unsigned char vme_int_pend; /* +06 VME interrupt pending register */ unsigned char reserved3; unsigned char bd_int_mask; /* +08 board interrupt mask register */ unsigned char reserved4; unsigned char bd_int_pend; /* +0A board interrupt pending register */ unsigned char reserved5; unsigned char bd_ctrl; /* +0C board control register */ unsigned char reserved6; unsigned char bd_status; /* +0E board status register */ unsigned char reserved7; unsigned char vme_irq; /* +10 VME interrupt request register */ unsigned char reserved8; unsigned char vme_ivec; /* +12 VME interrupt vector register */ unsigned char reserved9; unsigned char cli_mbox; /* +14 clear mailbox irq */ unsigned char reservedA; unsigned char rtc; /* +16 RTC control register */ unsigned char reservedB; unsigned char mbox_data; /* +18 mailbox read/write register */ unsigned char reservedC; unsigned char wd_trigger; /* +1A Watchdog trigger register */ unsigned char reservedD; unsigned char rmw_req; /* +1C RMW request register */ unsigned char reservedE; unsigned char bd_rev; /* +1E Board Revision register */ } ip860_bcsr_t; #endif /* __ASSEMBLY__ */ /*----------------------------------------------------------------------- * Board Control Register: bd_ctrl (Offset 0x0C) *----------------------------------------------------------------------- */ #define BD_CTRL_IPLSE 0x80 /* IP Slot Long Select Enable */ #define BD_CTRL_WDOGE 0x40 /* Watchdog Enable */ #define BD_CTRL_FLWE 0x20 /* Flash Write Enable */ #define BD_CTRL_RWDN 0x10 /* VMEBus Requester Release When Done Enable */ #endif /* __CONFIG_H */