/* * (C) Copyright 2001 * Josh Huber , Mission Critical Linux, Inc. * * SPDX-License-Identifier: GPL-2.0+ */ /* * board/config.h - configuration options, board specific */ /************************************************************************* * (c) 2004 esd gmbh Hannover * * * from db64360.h file * by Reinhard Arlt reinhard.arlt@esd-electronics.com * ************************************************************************/ #ifndef __CONFIG_H #define __CONFIG_H /* This define must be before the core.h include */ #define CONFIG_CPCI750 1 /* this is an CPCI750 board */ #ifndef __ASSEMBLY__ #include <../board/Marvell/include/core.h> #endif /*-----------------------------------------------------*/ #include "../board/esd/cpci750/local.h" /* * High Level Configuration Options * (easy to change) */ #define CONFIG_750FX /* we have a 750FX (override local.h) */ #define CONFIG_CPCI750 1 /* this is an CPCI750 board */ #define CONFIG_SYS_TEXT_BASE 0xfff00000 #define CONFIG_BAUDRATE 9600 /* console baudrate = 9600 */ #define CONFIG_MV64360_ECC /* enable ECC support */ #define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* which initialization functions to call for this board */ #define CONFIG_MISC_INIT_R #define CONFIG_BOARD_PRE_INIT #define CONFIG_BOARD_EARLY_INIT_F 1 #define CONFIG_SYS_BOARD_NAME "CPCI750" #define CONFIG_IDENT_STRING "Marvell 64360 + IBM750FX" /*#define CONFIG_SYS_HUSH_PARSER*/ #define CONFIG_SYS_HUSH_PARSER #define CONFIG_CMDLINE_EDITING /* add command line history */ #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ /* Define which ETH port will be used for connecting the network */ #define CONFIG_SYS_ETH_PORT ETH_0 /* * The following defines let you select what serial you want to use * for your console driver. * * what to do: * to use the DUART, undef CONFIG_MPSC. If you have hacked a serial * cable onto the second DUART channel, change the CONFIG_SYS_DUART port from 1 * to 0 below. * * to use the MPSC, #define CONFIG_MPSC. If you have wired up another * mpsc channel, change CONFIG_MPSC_PORT to the desired value. */ #define CONFIG_MPSC #define CONFIG_MPSC_PORT 0 /* to change the default ethernet port, use this define (options: 0, 1, 2) */ #define MV_ETH_DEVS 1 #define CONFIG_ETHER_PORT 0 #undef CONFIG_ETHER_PORT_MII /* use RMII */ #define CONFIG_BOOTDELAY 5 /* autoboot disabled */ #define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ #define CONFIG_ZERO_BOOTDELAY_CHECK #undef CONFIG_BOOTARGS /* ----------------------------------------------------------------------------- * New bootcommands for Marvell CPCI750 c 2002 Ingo Assmus */ #define CONFIG_IPADDR "192.168.0.185" #define CONFIG_SERIAL "AA000001" #define CONFIG_SERVERIP "10.0.0.79" #define CONFIG_ROOTPATH "/export/nfs_cpci750/%s" #define CONFIG_TESTDRAMDATA y #define CONFIG_TESTDRAMADDRESS n #define CONFIG_TESETDRAMWALK n /* ----------------------------------------------------------------------------- */ #define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate changes */ #undef CONFIG_WATCHDOG /* watchdog disabled */ #undef CONFIG_ALTIVEC /* undef to disable */ /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_BOOTFILESIZE /* * Command line configuration. */ #include #define CONFIG_CMD_ASKENV #define CONFIG_CMD_I2C #define CONFIG_CMD_CACHE #define CONFIG_CMD_EEPROM #define CONFIG_CMD_PCI #define CONFIG_CMD_ELF #define CONFIG_CMD_DATE #define CONFIG_CMD_NET #define CONFIG_CMD_PING #define CONFIG_CMD_IDE #define CONFIG_CMD_FAT #define CONFIG_CMD_EXT2 #define CONFIG_DOS_PARTITION #define CONFIG_USE_CPCIDVI #ifdef CONFIG_USE_CPCIDVI #define CONFIG_VIDEO #define CONFIG_VIDEO_CT69000 #define CONFIG_CFB_CONSOLE #define CONFIG_VIDEO_SW_CURSOR #define CONFIG_VIDEO_LOGO #define CONFIG_I8042_KBD #define CONFIG_SYS_ISA_IO 0 #endif /* * Miscellaneous configurable options */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_SPEED 80000 /* I2C speed default */ #define CONFIG_PRAM 0 #define CONFIG_SYS_GT_DUAL_CPU /* also for JTAG even with one cpu */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ /*#define CONFIG_SYS_MEMTEST_START 0x00400000*/ /* memtest works on */ /*#define CONFIG_SYS_MEMTEST_END 0x00C00000*/ /* 4 ... 12 MB in DRAM */ /*#define CONFIG_SYS_MEMTEST_END 0x07c00000*/ /* 4 ... 124 MB in DRAM */ /* #define CONFIG_SYS_DRAM_TEST * DRAM tests * CONFIG_SYS_DRAM_TEST - enables the following tests. * * CONFIG_SYS_DRAM_TEST_DATA - Enables test for shorted or open data lines * Environment variable 'test_dram_data' must be * set to 'y'. * CONFIG_SYS_DRAM_TEST_DATA - Enables test to verify that each word is uniquely * addressable. Environment variable * 'test_dram_address' must be set to 'y'. * CONFIG_SYS_DRAM_TEST_WALK - Enables test a 64-bit walking ones pattern test. * This test takes about 6 minutes to test 64 MB. * Environment variable 'test_dram_walk' must be * set to 'y'. */ #define CONFIG_SYS_DRAM_TEST #if defined(CONFIG_SYS_DRAM_TEST) #define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */ /*#define CONFIG_SYS_MEMTEST_END 0x00C00000*/ /* 4 ... 12 MB in DRAM */ #define CONFIG_SYS_MEMTEST_END 0x07c00000 /* 4 ... 124 MB in DRAM */ #define CONFIG_SYS_DRAM_TEST_DATA #define CONFIG_SYS_DRAM_TEST_ADDRESS #define CONFIG_SYS_DRAM_TEST_WALK #endif /* CONFIG_SYS_DRAM_TEST */ #define CONFIG_DISPLAY_MEMMAP /* at the end of the bootprocess show the memory map */ #undef CONFIG_SYS_DISPLAY_DIMM_SPD_CONTENT /* show SPD content during boot */ #define CONFIG_SYS_LOAD_ADDR 0x00300000 /* default load address */ #define CONFIG_SYS_BUS_CLK 133000000 /* 133 MHz (CPU = 5*Bus = 666MHz) */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } #define CONFIG_SYS_TCLK 133000000 /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area */ /* * When locking data in cache you should point the CONFIG_SYS_INIT_RAM_ADDRESS * To an unused memory region. The stack will remain in cache until RAM * is initialized */ #undef CONFIG_SYS_INIT_RAM_LOCK /* #define CONFIG_SYS_INIT_RAM_ADDR 0x40000000*/ /* unused memory region */ /* #define CONFIG_SYS_INIT_RAM_ADDR 0xfba00000*/ /* unused memory region */ #define CONFIG_SYS_INIT_RAM_ADDR 0xf1080000 /* unused memory region */ #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define RELOCATE_INTERNAL_RAM_ADDR #ifdef RELOCATE_INTERNAL_RAM_ADDR /*#define CONFIG_SYS_INTERNAL_RAM_ADDR 0xfba00000*/ #define CONFIG_SYS_INTERNAL_RAM_ADDR 0xf1080000 #endif /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 /* Dummies for BAT 4-7 */ #define CONFIG_SYS_SDRAM1_BASE 0x10000000 /* each 256 MByte */ #define CONFIG_SYS_SDRAM2_BASE 0x20000000 #define CONFIG_SYS_SDRAM3_BASE 0x30000000 #define CONFIG_SYS_SDRAM4_BASE 0x40000000 #define CONFIG_SYS_RESET_ADDRESS 0xfff00100 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CONFIG_SYS_MONITOR_BASE 0xfff00000 #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 256 kB for malloc */ /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ #define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */ #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of flash banks */ #define CONFIG_SYS_MAX_FLASH_BANKS 4 /* max number of memory banks */ #define CONFIG_SYS_FLASH_INCREMENT 0x01000000 /* size of flash bank */ #define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, \ CONFIG_SYS_FLASH_BASE + 1*CONFIG_SYS_FLASH_INCREMENT, \ CONFIG_SYS_FLASH_BASE + 2*CONFIG_SYS_FLASH_INCREMENT, \ CONFIG_SYS_FLASH_BASE + 3*CONFIG_SYS_FLASH_INCREMENT } #define CONFIG_SYS_FLASH_EMPTY_INFO 1 /* show if bank is empty */ /* areas to map different things with the GT in physical space */ #define CONFIG_SYS_DRAM_BANKS 4 /* What to put in the bats. */ #define CONFIG_SYS_MISC_REGION_BASE 0xf0000000 /* Peripheral Device section */ /*******************************************************/ /* We have on the cpci750 Board : */ /* GT-Chipset Register Area */ /* GT-Chipset internal SRAM 256k */ /* SRAM on external device module */ /* Real time clock on external device module */ /* dobble UART on external device module */ /* Data flash on external device module */ /* Boot flash on external device module */ /*******************************************************/ #define CONFIG_SYS_DFL_GT_REGS 0x14000000 /* boot time GT_REGS */ #define CONFIG_SYS_CPCI750_RESET_ADDR 0x14000000 /* After power on Reset the CPCI750 is here */ #undef MARVEL_STANDARD_CFG #ifndef MARVEL_STANDARD_CFG /*++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++*/ #define CONFIG_SYS_GT_REGS 0xf1000000 /* GT Registers will be mapped here */ /*#define CONFIG_SYS_DEV_BASE 0xfc000000*/ /* GT Devices CS start here */ #define CONFIG_SYS_INT_SRAM_BASE 0xf1080000 /* GT offers 256k internal fast SRAM */ #define CONFIG_SYS_BOOT_SPACE 0xff000000 /* BOOT_CS0 flash 0 */ #define CONFIG_SYS_DEV0_SPACE 0xfc000000 /* DEV_CS0 flash 1 */ #define CONFIG_SYS_DEV1_SPACE 0xfd000000 /* DEV_CS1 flash 2 */ #define CONFIG_SYS_DEV2_SPACE 0xfe000000 /* DEV_CS2 flash 3 */ #define CONFIG_SYS_DEV3_SPACE 0xf0000000 /* DEV_CS3 nvram/can */ #define CONFIG_SYS_BOOT_SIZE _16M /* cpci750 flash 0 */ #define CONFIG_SYS_DEV0_SIZE _16M /* cpci750 flash 1 */ #define CONFIG_SYS_DEV1_SIZE _16M /* cpci750 flash 2 */ #define CONFIG_SYS_DEV2_SIZE _16M /* cpci750 flash 3 */ #define CONFIG_SYS_DEV3_SIZE _16M /* cpci750 nvram/can */ /*++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++*/ #endif /* Reset values for Port behavior (8bit/ 32bit, etc.) only corrected by device width */ #define CONFIG_SYS_DEV0_PAR 0x8FDFFFFF /* 16 bit flash */ #define CONFIG_SYS_DEV1_PAR 0x8FDFFFFF /* 16 bit flash */ #define CONFIG_SYS_DEV2_PAR 0x8FDFFFFF /* 16 bit flash */ #define CONFIG_SYS_DEV3_PAR 0x8FCFFFFF /* nvram/can */ #define CONFIG_SYS_BOOT_PAR 0x8FDFFFFF /* 16 bit flash */ /* c 4 a 8 2 4 1 c */ /* 33 22|2222|22 22|111 1|11 11|1 1 | | */ /* 10 98|7654|32 10|987 6|54 32|1 098|7 654|3 210 */ /* 11|00|0100|10 10|100|0 00|10 0|100 0|001 1|100 */ /* 3| 0|.... ..| 2| 4 | 0 | 4 | 8 | 3 | 4 */ /* MPP Control MV64360 Appendix P P. 632*/ #define CONFIG_SYS_MPP_CONTROL_0 0x00002222 /* */ #define CONFIG_SYS_MPP_CONTROL_1 0x11110000 /* */ #define CONFIG_SYS_MPP_CONTROL_2 0x11111111 /* */ #define CONFIG_SYS_MPP_CONTROL_3 0x00001111 /* */ /* #define CONFIG_SYS_SERIAL_PORT_MUX 0x00000102*/ /* */ #define CONFIG_SYS_GPP_LEVEL_CONTROL 0xffffffff /* 1111 1111 1111 1111 1111 1111 1111 1111*/ /* setup new config_value for MV64360 DDR-RAM To_do !! */ /*# define CONFIG_SYS_SDRAM_CONFIG 0xd8e18200*/ /* 0x448 */ /*# define CONFIG_SYS_SDRAM_CONFIG 0xd8e14400*/ /* 0x1400 */ /* GB has high prio. idma has low prio MPSC has low prio pci has low prio 1 and 2 cpu has high prio Data DQS pins == eight (DQS[7:0] foe x8 and x16 devices ECC disable non registered DRAM */ /* 31:26 25:22 21:20 19 18 17 16 */ /* 100001 0000 010 0 0 0 0 */ /* refresh_count=0x400 phisical interleaving disable virtual interleaving enable */ /* 15 14 13:0 */ /* 0 1 0x400 */ # define CONFIG_SYS_SDRAM_CONFIG 0x58200400 /* 0x1400 copied from Dink32 bzw. VxWorks*/ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ #define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ #define PCI_HOST_FORCE 1 /* configure as pci host */ #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show devices on bus */ /* PCI MEMORY MAP section */ #define CONFIG_SYS_PCI0_MEM_BASE 0x80000000 #define CONFIG_SYS_PCI0_MEM_SIZE _128M #define CONFIG_SYS_PCI1_MEM_BASE 0x88000000 #define CONFIG_SYS_PCI1_MEM_SIZE _128M #define CONFIG_SYS_PCI0_0_MEM_SPACE (CONFIG_SYS_PCI0_MEM_BASE) #define CONFIG_SYS_PCI1_0_MEM_SPACE (CONFIG_SYS_PCI1_MEM_BASE) /* PCI I/O MAP section */ #define CONFIG_SYS_PCI0_IO_BASE 0xfa000000 #define CONFIG_SYS_PCI0_IO_SIZE _16M #define CONFIG_SYS_PCI1_IO_BASE 0xfb000000 #define CONFIG_SYS_PCI1_IO_SIZE _16M #define CONFIG_SYS_PCI0_IO_SPACE (CONFIG_SYS_PCI0_IO_BASE) #define CONFIG_SYS_PCI0_IO_SPACE_PCI 0x00000000 #define CONFIG_SYS_PCI1_IO_SPACE (CONFIG_SYS_PCI1_IO_BASE) #define CONFIG_SYS_PCI1_IO_SPACE_PCI 0x00000000 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS (CONFIG_SYS_PCI0_IO_BASE) #if defined (CONFIG_750CX) #define CONFIG_SYS_PCI_IDSEL 0x0 #else #define CONFIG_SYS_PCI_IDSEL 0x30 #endif /*----------------------------------------------------------------------- * IDE/ATA stuff *----------------------------------------------------------------------- */ #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ #undef CONFIG_IDE_LED /* no led for ide supported */ #define CONFIG_IDE_RESET /* no reset for ide supported */ #define CONFIG_IDE_PREINIT /* check for units */ #define CONFIG_SYS_IDE_MAXBUS 2 /* max. 1 IDE busses */ #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 1 drives per IDE bus */ #define CONFIG_SYS_ATA_BASE_ADDR 0 #define CONFIG_SYS_ATA_IDE0_OFFSET 0 #define CONFIG_SYS_ATA_IDE1_OFFSET 0 #define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ #define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */ #ifndef __ASSEMBLY__ int ata_device(int dev); #endif #define ATA_DEVICE(dev) ata_device(dev) #define CONFIG_ATAPI 1 /*---------------------------------------------------------------------- * Initial BAT mappings */ /* NOTES: * 1) GUARDED and WRITE_THRU not allowed in IBATS * 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT */ /* SDRAM */ #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U /* init ram */ #define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) #define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_256K | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U /* PCI0, PCI1 in one BAT */ #define CONFIG_SYS_IBAT2L BATL_NO_ACCESS #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U #define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI0_MEM_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI0_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) /* GT regs, bootrom, all the devices, PCI I/O */ #define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW) #define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_BASE | BATU_VS | BATU_VP | BATU_BL_256M) #define CONFIG_SYS_DBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U /* * 750FX IBAT and DBAT pairs (To_do: define regins for I(D)BAT4 - I(D)BAT7) * IBAT4 and DBAT4 * FIXME: ingo disable BATs for Linux Kernel */ /* #undef SETUP_HIGH_BATS_FX750 */ /* don't initialize BATS 4-7 */ #define SETUP_HIGH_BATS_FX750 /* initialize BATS 4-7 */ #ifdef SETUP_HIGH_BATS_FX750 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT4U (CONFIG_SYS_SDRAM1_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT4L (CONFIG_SYS_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U /* IBAT5 and DBAT5 */ #define CONFIG_SYS_IBAT5L (CONFIG_SYS_SDRAM2_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT5U (CONFIG_SYS_SDRAM2_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT5L (CONFIG_SYS_SDRAM2_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U /* IBAT6 and DBAT6 */ #define CONFIG_SYS_IBAT6L (CONFIG_SYS_SDRAM3_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT6U (CONFIG_SYS_SDRAM3_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT6L (CONFIG_SYS_SDRAM3_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U /* IBAT7 and DBAT7 */ #define CONFIG_SYS_IBAT7L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT7U (CONFIG_SYS_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT7L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U #else /* set em out of range for Linux !!!!!!!!!!! */ #define CONFIG_SYS_IBAT4L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT4U (CONFIG_SYS_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT4L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U /* IBAT5 and DBAT5 */ #define CONFIG_SYS_IBAT5L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT5U (CONFIG_SYS_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT5L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT4U /* IBAT6 and DBAT6 */ #define CONFIG_SYS_IBAT6L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT6U (CONFIG_SYS_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT6L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT4U /* IBAT7 and DBAT7 */ #define CONFIG_SYS_IBAT7L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT7U (CONFIG_SYS_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT7L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT4U #endif /* FIXME: ingo end: disable BATs for Linux Kernel */ /* I2C addresses for the two DIMM SPD chips */ #define DIMM0_I2C_ADDR 0x51 #define DIMM1_I2C_ADDR 0x52 /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_BOOT_FLASH_WIDTH 2 /* 16 bit */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #define CONFIG_SYS_FLASH_LOCK_TOUT 500 /* Timeout for Flash Lock (in ms) */ #if 0 #define CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ #define CONFIG_ENV_SECT_SIZE 0x10000 #define CONFIG_ENV_ADDR 0xFFF78000 /* Marvell 8-Bit Bootflash last sector */ /* #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+CONFIG_SYS_MONITOR_LEN-CONFIG_ENV_SECT_SIZE) */ #endif #define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x050 #define CONFIG_ENV_OFFSET 0x200 /* environment starts at the beginning of the EEPROM */ #define CONFIG_ENV_SIZE 0x600 /* 2048 bytes may be used for env vars*/ #define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */ #define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */ #define CONFIG_SYS_VXWORKS_MAC_PTR (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-0x40) /*----------------------------------------------------------------------- * Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /*----------------------------------------------------------------------- * L2CR setup -- make sure this is right for your board! * look in include/mpc74xx.h for the defines used here */ /*#define CONFIG_SYS_L2*/ #undef CONFIG_SYS_L2 /* #ifdef CONFIG_750CX*/ #if defined (CONFIG_750CX) || defined (CONFIG_750FX) #define L2_INIT 0 #else #define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \ L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT) #endif #define L2_ENABLE (L2_INIT | L2CR_L2E) #define CONFIG_SYS_BOARD_ASM_INIT 1 #define CPCI750_SLAVE_TEST (((in8(0xf0300000) & 0x80) == 0) ? 0 : 1) #define CPCI750_ECC_TEST (((in8(0xf0300000) & 0x02) == 0) ? 1 : 0) #define CONFIG_SYS_PLD_VER 0xf0e00000 #define CONFIG_OF_LIBFDT 1 #endif /* __CONFIG_H */