menu "NAND Device Support" config SYS_NAND_SELF_INIT bool help This option, if enabled, provides more flexible and linux-like NAND initialization process. config NAND_DENALI bool "Support Denali NAND controller" select SYS_NAND_SELF_INIT help Enable support for the Denali NAND controller. config SYS_NAND_DENALI_64BIT bool "Use 64-bit variant of Denali NAND controller" depends on NAND_DENALI help The Denali NAND controller IP has some variations in terms of the bus interface. The DMA setup sequence is completely differenct between 32bit / 64bit AXI bus variants. If your Denali NAND controller is the 64-bit variant, say Y. Otherwise (32 bit), say N. config NAND_DENALI_SPARE_AREA_SKIP_BYTES int "Number of bytes skipped in OOB area" depends on NAND_DENALI range 0 63 help This option specifies the number of bytes to skip from the beginning of OOB area before last ECC sector data starts. This is potentially used to preserve the bad block marker in the OOB area. config NAND_VF610_NFC bool "Support for Freescale NFC for VF610/MPC5125" select SYS_NAND_SELF_INIT help Enables support for NAND Flash Controller on some Freescale processors like the VF610, MPC5125, MCF54418 or Kinetis K70. The driver supports a maximum 2k page size. The driver currently does not support hardware ECC. choice prompt "Hardware ECC strength" depends on NAND_VF610_NFC default SYS_NAND_VF610_NFC_45_ECC_BYTES help Select the ECC strength used in the hardware BCH ECC block. config SYS_NAND_VF610_NFC_45_ECC_BYTES bool "24-error correction (45 ECC bytes)" config SYS_NAND_VF610_NFC_60_ECC_BYTES bool "32-error correction (60 ECC bytes)" endchoice config NAND_PXA3XX bool "Support for NAND on PXA3xx and Armada 370/XP/38x" select SYS_NAND_SELF_INIT help This enables the driver for the NAND flash device found on PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2). config NAND_SUNXI bool "Support for NAND on Allwinner SoCs in SPL" depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I select SYS_NAND_SELF_INIT ---help--- Enable support for NAND. This option allows SPL to read from sunxi NAND using DMA transfers. config NAND_ARASAN bool "Configure Arasan Nand" help This enables Nand driver support for Arasan nand flash controller. This uses the hardware ECC for read and write operations. comment "Generic NAND options" # Enhance depends when converting drivers to Kconfig which use this config # option (mxc_nand, ndfc, omap_gpmc). config SYS_NAND_BUSWIDTH_16BIT bool "Use 16-bit NAND interface" depends on NAND_VF610_NFC help Indicates that NAND device has 16-bit wide data-bus. In absence of this config, bus-width of NAND device is assumed to be either 8-bit and later determined by reading ONFI params. Above config is useful when NAND device's bus-width information cannot be determined from on-chip ONFI params, like in following scenarios: - SPL boot does not support reading of ONFI parameters. This is done to keep SPL code foot-print small. - In current U-Boot flow using nand_init(), driver initialization happens in board_nand_init() which is called before any device probe (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are not available while configuring controller. So a static CONFIG_NAND_xx is needed to know the device's bus-width in advance. if SPL config SYS_NAND_U_BOOT_LOCATIONS bool "Define U-boot binaries locations in NAND" help Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig. This option should not be enabled when compiling U-boot for boards defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/.h file. config SYS_NAND_U_BOOT_OFFS hex "Location in NAND to read U-Boot from" default 0x8000 if NAND_SUNXI depends on SYS_NAND_U_BOOT_LOCATIONS help Set the offset from the start of the nand where u-boot should be loaded from. config SYS_NAND_U_BOOT_OFFS_REDUND hex "Location in NAND to read U-Boot from" default SYS_NAND_U_BOOT_OFFS depends on SYS_NAND_U_BOOT_LOCATIONS help Set the offset from the start of the nand where the redundant u-boot should be loaded from. config SPL_NAND_DENALI bool "Support Denali NAND controller for SPL" help This is a small implementation of the Denali NAND controller for use on SPL. endif endmenu