/* * i2c driver for Freescale i.MX series * * (c) 2007 Pengutronix, Sascha Hauer * (c) 2011 Marek Vasut * * Based on i2c-imx.c from linux kernel: * Copyright (C) 2005 Torsten Koschorrek * Copyright (C) 2005 Matthias Blaschke * Copyright (C) 2007 RightHand Technologies, Inc. * Copyright (C) 2008 Darius Augulis * * * SPDX-License-Identifier: GPL-2.0+ */ #include #include #include #include #include #include #include DECLARE_GLOBAL_DATA_PTR; #ifdef I2C_QUIRK_REG struct mxc_i2c_regs { uint8_t iadr; uint8_t ifdr; uint8_t i2cr; uint8_t i2sr; uint8_t i2dr; }; #else struct mxc_i2c_regs { uint32_t iadr; uint32_t ifdr; uint32_t i2cr; uint32_t i2sr; uint32_t i2dr; }; #endif #define I2CR_IIEN (1 << 6) #define I2CR_MSTA (1 << 5) #define I2CR_MTX (1 << 4) #define I2CR_TX_NO_AK (1 << 3) #define I2CR_RSTA (1 << 2) #define I2SR_ICF (1 << 7) #define I2SR_IBB (1 << 5) #define I2SR_IAL (1 << 4) #define I2SR_IIF (1 << 1) #define I2SR_RX_NO_AK (1 << 0) #ifdef I2C_QUIRK_REG #define I2CR_IEN (0 << 7) #define I2CR_IDIS (1 << 7) #define I2SR_IIF_CLEAR (1 << 1) #else #define I2CR_IEN (1 << 7) #define I2CR_IDIS (0 << 7) #define I2SR_IIF_CLEAR (0 << 1) #endif #if defined(CONFIG_HARD_I2C) && !defined(CONFIG_SYS_I2C_BASE) #error "define CONFIG_SYS_I2C_BASE to use the mxc_i2c driver" #endif #ifdef I2C_QUIRK_REG static u16 i2c_clk_div[60][2] = { { 20, 0x00 }, { 22, 0x01 }, { 24, 0x02 }, { 26, 0x03 }, { 28, 0x04 }, { 30, 0x05 }, { 32, 0x09 }, { 34, 0x06 }, { 36, 0x0A }, { 40, 0x07 }, { 44, 0x0C }, { 48, 0x0D }, { 52, 0x43 }, { 56, 0x0E }, { 60, 0x45 }, { 64, 0x12 }, { 68, 0x0F }, { 72, 0x13 }, { 80, 0x14 }, { 88, 0x15 }, { 96, 0x19 }, { 104, 0x16 }, { 112, 0x1A }, { 128, 0x17 }, { 136, 0x4F }, { 144, 0x1C }, { 160, 0x1D }, { 176, 0x55 }, { 192, 0x1E }, { 208, 0x56 }, { 224, 0x22 }, { 228, 0x24 }, { 240, 0x1F }, { 256, 0x23 }, { 288, 0x5C }, { 320, 0x25 }, { 384, 0x26 }, { 448, 0x2A }, { 480, 0x27 }, { 512, 0x2B }, { 576, 0x2C }, { 640, 0x2D }, { 768, 0x31 }, { 896, 0x32 }, { 960, 0x2F }, { 1024, 0x33 }, { 1152, 0x34 }, { 1280, 0x35 }, { 1536, 0x36 }, { 1792, 0x3A }, { 1920, 0x37 }, { 2048, 0x3B }, { 2304, 0x3C }, { 2560, 0x3D }, { 3072, 0x3E }, { 3584, 0x7A }, { 3840, 0x3F }, { 4096, 0x7B }, { 5120, 0x7D }, { 6144, 0x7E }, }; #else static u16 i2c_clk_div[50][2] = { { 22, 0x20 }, { 24, 0x21 }, { 26, 0x22 }, { 28, 0x23 }, { 30, 0x00 }, { 32, 0x24 }, { 36, 0x25 }, { 40, 0x26 }, { 42, 0x03 }, { 44, 0x27 }, { 48, 0x28 }, { 52, 0x05 }, { 56, 0x29 }, { 60, 0x06 }, { 64, 0x2A }, { 72, 0x2B }, { 80, 0x2C }, { 88, 0x09 }, { 96, 0x2D }, { 104, 0x0A }, { 112, 0x2E }, { 128, 0x2F }, { 144, 0x0C }, { 160, 0x30 }, { 192, 0x31 }, { 224, 0x32 }, { 240, 0x0F }, { 256, 0x33 }, { 288, 0x10 }, { 320, 0x34 }, { 384, 0x35 }, { 448, 0x36 }, { 480, 0x13 }, { 512, 0x37 }, { 576, 0x14 }, { 640, 0x38 }, { 768, 0x39 }, { 896, 0x3A }, { 960, 0x17 }, { 1024, 0x3B }, { 1152, 0x18 }, { 1280, 0x3C }, { 1536, 0x3D }, { 1792, 0x3E }, { 1920, 0x1B }, { 2048, 0x3F }, { 2304, 0x1C }, { 2560, 0x1D }, { 3072, 0x1E }, { 3840, 0x1F } }; #endif #ifndef CONFIG_SYS_MXC_I2C1_SPEED #define CONFIG_SYS_MXC_I2C1_SPEED 100000 #endif #ifndef CONFIG_SYS_MXC_I2C2_SPEED #define CONFIG_SYS_MXC_I2C2_SPEED 100000 #endif #ifndef CONFIG_SYS_MXC_I2C3_SPEED #define CONFIG_SYS_MXC_I2C3_SPEED 100000 #endif #ifndef CONFIG_SYS_MXC_I2C1_SLAVE #define CONFIG_SYS_MXC_I2C1_SLAVE 0 #endif #ifndef CONFIG_SYS_MXC_I2C2_SLAVE #define CONFIG_SYS_MXC_I2C2_SLAVE 0 #endif #ifndef CONFIG_SYS_MXC_I2C3_SLAVE #define CONFIG_SYS_MXC_I2C3_SLAVE 0 #endif /* * Calculate and set proper clock divider */ static uint8_t i2c_imx_get_clk(unsigned int rate) { unsigned int i2c_clk_rate; unsigned int div; u8 clk_div; #if defined(CONFIG_MX31) struct clock_control_regs *sc_regs = (struct clock_control_regs *)CCM_BASE; /* start the required I2C clock */ writel(readl(&sc_regs->cgr0) | (3 << CONFIG_SYS_I2C_CLK_OFFSET), &sc_regs->cgr0); #endif /* Divider value calculation */ i2c_clk_rate = mxc_get_clock(MXC_I2C_CLK); div = (i2c_clk_rate + rate - 1) / rate; if (div < i2c_clk_div[0][0]) clk_div = 0; else if (div > i2c_clk_div[ARRAY_SIZE(i2c_clk_div) - 1][0]) clk_div = ARRAY_SIZE(i2c_clk_div) - 1; else for (clk_div = 0; i2c_clk_div[clk_div][0] < div; clk_div++) ; /* Store divider value */ return clk_div; } /* * Set I2C Bus speed */ static int bus_i2c_set_bus_speed(void *base, int speed) { struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)base; u8 clk_idx = i2c_imx_get_clk(speed); u8 idx = i2c_clk_div[clk_idx][1]; /* Store divider value */ writeb(idx, &i2c_regs->ifdr); /* Reset module */ writeb(I2CR_IDIS, &i2c_regs->i2cr); writeb(0, &i2c_regs->i2sr); return 0; } #define ST_BUS_IDLE (0 | (I2SR_IBB << 8)) #define ST_BUS_BUSY (I2SR_IBB | (I2SR_IBB << 8)) #define ST_IIF (I2SR_IIF | (I2SR_IIF << 8)) static int wait_for_sr_state(struct mxc_i2c_regs *i2c_regs, unsigned state) { unsigned sr; ulong elapsed; ulong start_time = get_timer(0); for (;;) { sr = readb(&i2c_regs->i2sr); if (sr & I2SR_IAL) { #ifdef I2C_QUIRK_REG writeb(sr | I2SR_IAL, &i2c_regs->i2sr); #else writeb(sr & ~I2SR_IAL, &i2c_regs->i2sr); #endif printf("%s: Arbitration lost sr=%x cr=%x state=%x\n", __func__, sr, readb(&i2c_regs->i2cr), state); return -ERESTART; } if ((sr & (state >> 8)) == (unsigned char)state) return sr; WATCHDOG_RESET(); elapsed = get_timer(start_time); if (elapsed > (CONFIG_SYS_HZ / 10)) /* .1 seconds */ break; } printf("%s: failed sr=%x cr=%x state=%x\n", __func__, sr, readb(&i2c_regs->i2cr), state); return -ETIMEDOUT; } static int tx_byte(struct mxc_i2c_regs *i2c_regs, u8 byte) { int ret; writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr); writeb(byte, &i2c_regs->i2dr); ret = wait_for_sr_state(i2c_regs, ST_IIF); if (ret < 0) return ret; if (ret & I2SR_RX_NO_AK) return -ENODEV; return 0; } /* * Stop I2C transaction */ static void i2c_imx_stop(struct mxc_i2c_regs *i2c_regs) { int ret; unsigned int temp = readb(&i2c_regs->i2cr); temp &= ~(I2CR_MSTA | I2CR_MTX); writeb(temp, &i2c_regs->i2cr); ret = wait_for_sr_state(i2c_regs, ST_BUS_IDLE); if (ret < 0) printf("%s:trigger stop failed\n", __func__); } /* * Send start signal, chip address and * write register address */ static int i2c_init_transfer_(struct mxc_i2c_regs *i2c_regs, uchar chip, uint addr, int alen) { unsigned int temp; int ret; /* Enable I2C controller */ #ifdef I2C_QUIRK_REG if (readb(&i2c_regs->i2cr) & I2CR_IDIS) { #else if (!(readb(&i2c_regs->i2cr) & I2CR_IEN)) { #endif writeb(I2CR_IEN, &i2c_regs->i2cr); /* Wait for controller to be stable */ udelay(50); } if (readb(&i2c_regs->iadr) == (chip << 1)) writeb((chip << 1) ^ 2, &i2c_regs->iadr); writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr); ret = wait_for_sr_state(i2c_regs, ST_BUS_IDLE); if (ret < 0) return ret; /* Start I2C transaction */ temp = readb(&i2c_regs->i2cr); temp |= I2CR_MSTA; writeb(temp, &i2c_regs->i2cr); ret = wait_for_sr_state(i2c_regs, ST_BUS_BUSY); if (ret < 0) return ret; temp |= I2CR_MTX | I2CR_TX_NO_AK; writeb(temp, &i2c_regs->i2cr); /* write slave address */ ret = tx_byte(i2c_regs, chip << 1); if (ret < 0) return ret; while (alen--) { ret = tx_byte(i2c_regs, (addr >> (alen * 8)) & 0xff); if (ret < 0) return ret; } return 0; } static int i2c_idle_bus(void *base); static int i2c_init_transfer(struct mxc_i2c_regs *i2c_regs, uchar chip, uint addr, int alen) { int retry; int ret; for (retry = 0; retry < 3; retry++) { ret = i2c_init_transfer_(i2c_regs, chip, addr, alen); if (ret >= 0) return 0; i2c_imx_stop(i2c_regs); if (ret == -ENODEV) return ret; printf("%s: failed for chip 0x%x retry=%d\n", __func__, chip, retry); if (ret != -ERESTART) /* Disable controller */ writeb(I2CR_IDIS, &i2c_regs->i2cr); udelay(100); if (i2c_idle_bus(i2c_regs) < 0) break; } printf("%s: give up i2c_regs=%p\n", __func__, i2c_regs); return ret; } /* * Read data from I2C device */ int bus_i2c_read(void *base, uchar chip, uint addr, int alen, uchar *buf, int len) { int ret; unsigned int temp; int i; struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)base; ret = i2c_init_transfer(i2c_regs, chip, addr, alen); if (ret < 0) return ret; temp = readb(&i2c_regs->i2cr); temp |= I2CR_RSTA; writeb(temp, &i2c_regs->i2cr); ret = tx_byte(i2c_regs, (chip << 1) | 1); if (ret < 0) { i2c_imx_stop(i2c_regs); return ret; } /* setup bus to read data */ temp = readb(&i2c_regs->i2cr); temp &= ~(I2CR_MTX | I2CR_TX_NO_AK); if (len == 1) temp |= I2CR_TX_NO_AK; writeb(temp, &i2c_regs->i2cr); writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr); readb(&i2c_regs->i2dr); /* dummy read to clear ICF */ /* read data */ for (i = 0; i < len; i++) { ret = wait_for_sr_state(i2c_regs, ST_IIF); if (ret < 0) { i2c_imx_stop(i2c_regs); return ret; } /* * It must generate STOP before read I2DR to prevent * controller from generating another clock cycle */ if (i == (len - 1)) { i2c_imx_stop(i2c_regs); } else if (i == (len - 2)) { temp = readb(&i2c_regs->i2cr); temp |= I2CR_TX_NO_AK; writeb(temp, &i2c_regs->i2cr); } writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr); buf[i] = readb(&i2c_regs->i2dr); } i2c_imx_stop(i2c_regs); return 0; } /* * Write data to I2C device */ int bus_i2c_write(void *base, uchar chip, uint addr, int alen, const uchar *buf, int len) { int ret; int i; struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)base; ret = i2c_init_transfer(i2c_regs, chip, addr, alen); if (ret < 0) return ret; for (i = 0; i < len; i++) { ret = tx_byte(i2c_regs, buf[i]); if (ret < 0) break; } i2c_imx_stop(i2c_regs); return ret; } struct i2c_parms { void *base; void *idle_bus_data; int (*idle_bus_fn)(void *p); }; struct sram_data { unsigned curr_i2c_bus; struct i2c_parms i2c_data[3]; }; static void * const i2c_bases[] = { #if defined(CONFIG_MX25) (void *)IMX_I2C_BASE, (void *)IMX_I2C2_BASE, (void *)IMX_I2C3_BASE #elif defined(CONFIG_MX27) (void *)IMX_I2C1_BASE, (void *)IMX_I2C2_BASE #elif defined(CONFIG_MX31) || defined(CONFIG_MX35) || \ defined(CONFIG_MX51) || defined(CONFIG_MX53) || \ defined(CONFIG_MX6) || defined(CONFIG_LS102XA) (void *)I2C1_BASE_ADDR, (void *)I2C2_BASE_ADDR, (void *)I2C3_BASE_ADDR #elif defined(CONFIG_VF610) (void *)I2C0_BASE_ADDR #elif defined(CONFIG_FSL_LSCH3) (void *)I2C1_BASE_ADDR, (void *)I2C2_BASE_ADDR, (void *)I2C3_BASE_ADDR, (void *)I2C4_BASE_ADDR #else #error "architecture not supported" #endif }; void *i2c_get_base(struct i2c_adapter *adap) { return i2c_bases[adap->hwadapnr]; } static struct i2c_parms *i2c_get_parms(void *base) { struct sram_data *srdata = (void *)gd->srdata; int i = 0; struct i2c_parms *p = srdata->i2c_data; while (i < ARRAY_SIZE(srdata->i2c_data)) { if (p->base == base) return p; p++; i++; } printf("Invalid I2C base: %p\n", base); return NULL; } static int i2c_idle_bus(void *base) { struct i2c_parms *p = i2c_get_parms(base); if (p && p->idle_bus_fn) return p->idle_bus_fn(p->idle_bus_data); return 0; } static int mxc_i2c_read(struct i2c_adapter *adap, uint8_t chip, uint addr, int alen, uint8_t *buffer, int len) { return bus_i2c_read(i2c_get_base(adap), chip, addr, alen, buffer, len); } static int mxc_i2c_write(struct i2c_adapter *adap, uint8_t chip, uint addr, int alen, uint8_t *buffer, int len) { return bus_i2c_write(i2c_get_base(adap), chip, addr, alen, buffer, len); } /* * Test if a chip at a given address responds (probe the chip) */ static int mxc_i2c_probe(struct i2c_adapter *adap, uint8_t chip) { return bus_i2c_write(i2c_get_base(adap), chip, 0, 0, NULL, 0); } void bus_i2c_init(void *base, int speed, int unused, int (*idle_bus_fn)(void *p), void *idle_bus_data) { struct sram_data *srdata = (void *)gd->srdata; int i = 0; struct i2c_parms *p = srdata->i2c_data; if (!base) return; for (;;) { if (!p->base || (p->base == base)) { p->base = base; if (idle_bus_fn) { p->idle_bus_fn = idle_bus_fn; p->idle_bus_data = idle_bus_data; } break; } p++; i++; if (i >= ARRAY_SIZE(srdata->i2c_data)) return; } bus_i2c_set_bus_speed(base, speed); } /* * Init I2C Bus */ static void mxc_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr) { bus_i2c_init(i2c_get_base(adap), speed, slaveaddr, NULL, NULL); } /* * Set I2C Speed */ static uint mxc_i2c_set_bus_speed(struct i2c_adapter *adap, uint speed) { return bus_i2c_set_bus_speed(i2c_get_base(adap), speed); } /* * Register mxc i2c adapters */ U_BOOT_I2C_ADAP_COMPLETE(mxc0, mxc_i2c_init, mxc_i2c_probe, mxc_i2c_read, mxc_i2c_write, mxc_i2c_set_bus_speed, CONFIG_SYS_MXC_I2C1_SPEED, CONFIG_SYS_MXC_I2C1_SLAVE, 0) U_BOOT_I2C_ADAP_COMPLETE(mxc1, mxc_i2c_init, mxc_i2c_probe, mxc_i2c_read, mxc_i2c_write, mxc_i2c_set_bus_speed, CONFIG_SYS_MXC_I2C2_SPEED, CONFIG_SYS_MXC_I2C2_SLAVE, 1) #if defined(CONFIG_MX31) || defined(CONFIG_MX35) ||\ defined(CONFIG_MX51) || defined(CONFIG_MX53) ||\ defined(CONFIG_MX6) || defined(CONFIG_LS102XA) U_BOOT_I2C_ADAP_COMPLETE(mxc2, mxc_i2c_init, mxc_i2c_probe, mxc_i2c_read, mxc_i2c_write, mxc_i2c_set_bus_speed, CONFIG_SYS_MXC_I2C3_SPEED, CONFIG_SYS_MXC_I2C3_SLAVE, 2) #endif