/* * Part of this code has been derived from linux: * Universal Host Controller Interface driver for USB (take II). * * (c) 1999-2001 Georg Acher, acher@in.tum.de (executive slave) (base guitar) * Deti Fliegl, deti@fliegl.de (executive slave) (lead voice) * Thomas Sailer, sailer@ife.ee.ethz.ch (chief consultant) (cheer leader) * Roman Weissgaerber, weissg@vienna.at (virt root hub) (studio porter) * (c) 2000 Yggdrasil Computing, Inc. (port of new PCI interface support * from usb-ohci.c by Adam Richter, adam@yggdrasil.com). * (C) 2000 David Brownell, david-b@pacbell.net (usb-ohci.c) * * HW-initalization based on material of * * (C) Copyright 1999 Linus Torvalds * (C) Copyright 1999 Johannes Erdfelt * (C) Copyright 1999 Randy Dunlap * (C) Copyright 1999 Gregory P. Smith * * * Adapted for U-Boot: * (C) Copyright 2001 Denis Peter, MPL AG Switzerland * * SPDX-License-Identifier: GPL-2.0+ */ /********************************************************************** * How it works: * ------------- * The framelist / Transfer descriptor / Queue Heads are similar like * in the linux usb_uhci.c. * * During initialization, the following skeleton is allocated in init_skel: * * framespecific | common chain * * framelist[] * [ 0 ]-----> TD ---------\ * [ 1 ]-----> TD ----------> TD ------> QH -------> QH -------> QH ---> NULL * ... TD ---------/ * [1023]-----> TD --------/ * * ^^ ^^ ^^ ^^ ^^ * 7 TDs for 1 TD for Start of Start of End Chain * INT (2-128ms) 1ms-INT CTRL Chain BULK Chain * * * Since this is a bootloader, the isochronous transfer descriptor have been removed. * * Interrupt Transfers. * -------------------- * For Interrupt transfers USB_MAX_TEMP_INT_TD Transfer descriptor are available. They * will be inserted after the appropriate (depending the interval setting) skeleton TD. * If an interrupt has been detected the dev->irqhandler is called. The status and number * of transfered bytes is stored in dev->irq_status resp. dev->irq_act_len. If the * dev->irqhandler returns 0, the interrupt TD is removed and disabled. If an 1 is returned, * the interrupt TD will be reactivated. * * Control Transfers * ----------------- * Control Transfers are issued by filling the tmp_td with the appropriate data and connect * them to the qh_cntrl queue header. Before other control/bulk transfers can be issued, * the programm has to wait for completion. This does not allows asynchronous data transfer. * * Bulk Transfers * -------------- * Bulk Transfers are issued by filling the tmp_td with the appropriate data and connect * them to the qh_bulk queue header. Before other control/bulk transfers can be issued, * the programm has to wait for completion. This does not allows asynchronous data transfer. * * */ #include #include #ifdef CONFIG_USB_UHCI #include #include "usb_uhci.h" #define USB_MAX_TEMP_TD 128 /* number of temporary TDs for bulk and control transfers */ #define USB_MAX_TEMP_INT_TD 32 /* number of temporary TDs for Interrupt transfers */ #undef USB_UHCI_DEBUG #ifdef USB_UHCI_DEBUG #define USB_UHCI_PRINTF(fmt,args...) printf (fmt ,##args) #else #define USB_UHCI_PRINTF(fmt,args...) #endif static int irqvec = -1; /* irq vector, if -1 uhci is stopped / reseted */ unsigned int usb_base_addr; /* base address */ static uhci_td_t td_int[8]; /* Interrupt Transfer descriptors */ static uhci_qh_t qh_cntrl; /* control Queue Head */ static uhci_qh_t qh_bulk; /* bulk Queue Head */ static uhci_qh_t qh_end; /* end Queue Head */ static uhci_td_t td_last; /* last TD (linked with end chain) */ /* temporary tds */ static uhci_td_t tmp_td[USB_MAX_TEMP_TD]; /* temporary bulk/control td's */ static uhci_td_t tmp_int_td[USB_MAX_TEMP_INT_TD]; /* temporary interrupt td's */ static unsigned long framelist[1024] __attribute__ ((aligned (0x1000))); /* frame list */ static struct virt_root_hub rh; /* struct for root hub */ /********************************************************************** * some forward decleration */ int uhci_submit_rh_msg(struct usb_device *dev, unsigned long pipe, void *buffer, int transfer_len,struct devrequest *setup); /* fill a td with the approproiate data. Link, status, info and buffer * are used by the USB controller itselfes, dev is used to identify the * "connected" device */ void usb_fill_td(uhci_td_t* td,unsigned long link,unsigned long status, unsigned long info, unsigned long buffer, unsigned long dev) { td->link=swap_32(link); td->status=swap_32(status); td->info=swap_32(info); td->buffer=swap_32(buffer); td->dev_ptr=dev; } /* fill a qh with the approproiate data. Head and element are used by the USB controller * itselfes. As soon as a valid dev_ptr is filled, a td chain is connected to the qh. * Please note, that after completion of the td chain, the entry element is removed / * marked invalid by the USB controller. */ void usb_fill_qh(uhci_qh_t* qh,unsigned long head,unsigned long element) { qh->head=swap_32(head); qh->element=swap_32(element); qh->dev_ptr=0L; } /* get the status of a td->status */ unsigned long usb_uhci_td_stat(unsigned long status) { unsigned long result=0; result |= (status & TD_CTRL_NAK) ? USB_ST_NAK_REC : 0; result |= (status & TD_CTRL_STALLED) ? USB_ST_STALLED : 0; result |= (status & TD_CTRL_DBUFERR) ? USB_ST_BUF_ERR : 0; result |= (status & TD_CTRL_BABBLE) ? USB_ST_BABBLE_DET : 0; result |= (status & TD_CTRL_CRCTIMEO) ? USB_ST_CRC_ERR : 0; result |= (status & TD_CTRL_BITSTUFF) ? USB_ST_BIT_ERR : 0; result |= (status & TD_CTRL_ACTIVE) ? USB_ST_NOT_PROC : 0; return result; } /* get the status and the transfered len of a td chain. * called from the completion handler */ int usb_get_td_status(uhci_td_t *td,struct usb_device *dev) { unsigned long temp,info; unsigned long stat; uhci_td_t *mytd=td; if(dev->devnum==rh.devnum) return 0; dev->act_len=0; stat=0; do { temp=swap_32((unsigned long)mytd->status); stat=usb_uhci_td_stat(temp); info=swap_32((unsigned long)mytd->info); if(((info & 0xff)!= USB_PID_SETUP) && (((info >> 21) & 0x7ff)!= 0x7ff) && (temp & 0x7FF)!=0x7ff) { /* if not setup and not null data pack */ dev->act_len+=(temp & 0x7FF) + 1; /* the transfered len is act_len + 1 */ } if(stat) { /* status no ok */ dev->status=stat; return -1; } temp=swap_32((unsigned long)mytd->link); mytd=(uhci_td_t *)(temp & 0xfffffff0); }while((temp & 0x1)==0); /* process all TDs */ dev->status=stat; return 0; /* Ok */ } /*------------------------------------------------------------------- * LOW LEVEL STUFF * assembles QHs und TDs for control, bulk and iso *-------------------------------------------------------------------*/ /* Submits a control message. That is a Setup, Data and Status transfer. * Routine does not wait for completion. */ int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer, int transfer_len,struct devrequest *setup) { unsigned long destination, status; int maxsze = usb_maxpacket(dev, pipe); unsigned long dataptr; int len; int pktsze; int i=0; if (!maxsze) { USB_UHCI_PRINTF("uhci_submit_control_urb: pipesize for pipe %lx is zero\n", pipe); return -1; } if(((pipe>>8)&0x7f)==rh.devnum) { /* this is the root hub -> redirect it */ return uhci_submit_rh_msg(dev,pipe,buffer,transfer_len,setup); } USB_UHCI_PRINTF("uhci_submit_control start len %x, maxsize %x\n",transfer_len,maxsze); /* The "pipe" thing contains the destination in bits 8--18 */ destination = (pipe & PIPE_DEVEP_MASK) | USB_PID_SETUP; /* Setup stage */ /* 3 errors */ status = (pipe & TD_CTRL_LS) | TD_CTRL_ACTIVE | (3 << 27); /* (urb->transfer_flags & USB_DISABLE_SPD ? 0 : TD_CTRL_SPD); */ /* Build the TD for the control request, try forever, 8 bytes of data */ usb_fill_td(&tmp_td[i],UHCI_PTR_TERM ,status, destination | (7 << 21),(unsigned long)setup,(unsigned long)dev); #if 0 { char *sp=(char *)setup; printf("SETUP to pipe %lx: %x %x %x %x %x %x %x %x\n", pipe, sp[0],sp[1],sp[2],sp[3],sp[4],sp[5],sp[6],sp[7]); } #endif dataptr = (unsigned long)buffer; len=transfer_len; /* If direction is "send", change the frame from SETUP (0x2D) to OUT (0xE1). Else change it from SETUP to IN (0x69). */ destination = (pipe & PIPE_DEVEP_MASK) | ((pipe & USB_DIR_IN)==0 ? USB_PID_OUT : USB_PID_IN); while (len > 0) { /* data stage */ pktsze = len; i++; if (pktsze > maxsze) pktsze = maxsze; destination ^= 1 << TD_TOKEN_TOGGLE; /* toggle DATA0/1 */ usb_fill_td(&tmp_td[i],UHCI_PTR_TERM, status, destination | ((pktsze - 1) << 21),dataptr,(unsigned long)dev); /* Status, pktsze bytes of data */ tmp_td[i-1].link=swap_32((unsigned long)&tmp_td[i]); dataptr += pktsze; len -= pktsze; } /* Build the final TD for control status */ /* It's only IN if the pipe is out AND we aren't expecting data */ destination &= ~UHCI_PID; if (((pipe & USB_DIR_IN)==0) || (transfer_len == 0)) destination |= USB_PID_IN; else destination |= USB_PID_OUT; destination |= 1 << TD_TOKEN_TOGGLE; /* End in Data1 */ i++; status &=~TD_CTRL_SPD; /* no limit on errors on final packet , 0 bytes of data */ usb_fill_td(&tmp_td[i],UHCI_PTR_TERM, status | TD_CTRL_IOC, destination | (UHCI_NULL_DATA_SIZE << 21),0,(unsigned long)dev); tmp_td[i-1].link=swap_32((unsigned long)&tmp_td[i]); /* queue status td */ /* usb_show_td(i+1);*/ USB_UHCI_PRINTF("uhci_submit_control end (%d tmp_tds used)\n",i); /* first mark the control QH element terminated */ qh_cntrl.element=0xffffffffL; /* set qh active */ qh_cntrl.dev_ptr=(unsigned long)dev; /* fill in tmp_td_chain */ qh_cntrl.element=swap_32((unsigned long)&tmp_td[0]); return 0; } /*------------------------------------------------------------------- * Prepare TDs for bulk transfers. */ int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, void *buffer,int transfer_len) { unsigned long destination, status,info; unsigned long dataptr; int maxsze = usb_maxpacket(dev, pipe); int len; int i=0; if(transfer_len < 0) { printf("Negative transfer length in submit_bulk\n"); return -1; } if (!maxsze) return -1; /* The "pipe" thing contains the destination in bits 8--18. */ destination = (pipe & PIPE_DEVEP_MASK) | usb_packetid (pipe); /* 3 errors */ status = (pipe & TD_CTRL_LS) | TD_CTRL_ACTIVE | (3 << 27); /* ((urb->transfer_flags & USB_DISABLE_SPD) ? 0 : TD_CTRL_SPD) | (3 << 27); */ /* Build the TDs for the bulk request */ len = transfer_len; dataptr = (unsigned long)buffer; do { int pktsze = len; if (pktsze > maxsze) pktsze = maxsze; /* pktsze bytes of data */ info = destination | (((pktsze - 1)&UHCI_NULL_DATA_SIZE) << 21) | (usb_gettoggle (dev, usb_pipeendpoint (pipe), usb_pipeout (pipe)) << TD_TOKEN_TOGGLE); if((len-pktsze)==0) status |= TD_CTRL_IOC; /* last one generates INT */ usb_fill_td(&tmp_td[i],UHCI_PTR_TERM, status, info,dataptr,(unsigned long)dev); /* Status, pktsze bytes of data */ if(i>0) tmp_td[i-1].link=swap_32((unsigned long)&tmp_td[i]); i++; dataptr += pktsze; len -= pktsze; usb_dotoggle (dev, usb_pipeendpoint (pipe), usb_pipeout (pipe)); } while (len > 0); /* first mark the bulk QH element terminated */ qh_bulk.element=0xffffffffL; /* set qh active */ qh_bulk.dev_ptr=(unsigned long)dev; /* fill in tmp_td_chain */ qh_bulk.element=swap_32((unsigned long)&tmp_td[0]); return 0; } /* search a free interrupt td */ uhci_td_t *uhci_alloc_int_td(void) { int i; for(i=0;i free TD */ return &tmp_int_td[i]; } return NULL; } #if 0 void uhci_show_temp_int_td(void) { int i; for(i=0;i free TD */ printf("temp_td %d is assigned to dev %lx\n",i,tmp_int_td[i].dev_ptr); } printf("all others temp_tds are free\n"); } #endif /*------------------------------------------------------------------- * submits USB interrupt (ie. polling ;-) */ int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer,int transfer_len, int interval) { int nint, n; unsigned long status, destination; unsigned long info,tmp; uhci_td_t *mytd; if (interval < 0 || interval >= 256) return -1; if (interval == 0) nint = 0; else { for (nint = 0, n = 1; nint <= 8; nint++, n += n) /* round interval down to 2^n */ { if(interval < n) { interval = n / 2; break; } } nint--; } USB_UHCI_PRINTF("Rounded interval to %i, chain %i\n", interval, nint); mytd=uhci_alloc_int_td(); if(mytd==NULL) { printf("No free INT TDs found\n"); return -1; } status = (pipe & TD_CTRL_LS) | TD_CTRL_ACTIVE | TD_CTRL_IOC | (3 << 27); /* (urb->transfer_flags & USB_DISABLE_SPD ? 0 : TD_CTRL_SPD) | (3 << 27); */ destination =(pipe & PIPE_DEVEP_MASK) | usb_packetid (pipe) | (((transfer_len - 1) & 0x7ff) << 21); info = destination | (usb_gettoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe)) << TD_TOKEN_TOGGLE); tmp = swap_32(td_int[nint].link); usb_fill_td(mytd,tmp,status, info,(unsigned long)buffer,(unsigned long)dev); /* Link it */ tmp = swap_32((unsigned long)mytd); td_int[nint].link=tmp; usb_dotoggle (dev, usb_pipeendpoint (pipe), usb_pipeout (pipe)); return 0; } /********************************************************************** * Low Level functions */ void reset_hc(void) { /* Global reset for 100ms */ out16r( usb_base_addr + USBPORTSC1,0x0204); out16r( usb_base_addr + USBPORTSC2,0x0204); out16r( usb_base_addr + USBCMD,USBCMD_GRESET | USBCMD_RS); /* Turn off all interrupts */ out16r(usb_base_addr + USBINTR,0); mdelay(50); out16r( usb_base_addr + USBCMD,0); mdelay(10); } void start_hc(void) { int timeout = 1000; while(in16r(usb_base_addr + USBCMD) & USBCMD_HCRESET) { if (!--timeout) { printf("USBCMD_HCRESET timed out!\n"); break; } } /* Turn on all interrupts */ out16r(usb_base_addr + USBINTR,USBINTR_TIMEOUT | USBINTR_RESUME | USBINTR_IOC | USBINTR_SP); /* Start at frame 0 */ out16r(usb_base_addr + USBFRNUM,0); /* set Framebuffer base address */ out32r(usb_base_addr+USBFLBASEADD,(unsigned long)&framelist); /* Run and mark it configured with a 64-byte max packet */ out16r(usb_base_addr + USBCMD,USBCMD_RS | USBCMD_CF | USBCMD_MAXP); } /* Initialize the skeleton */ void usb_init_skel(void) { unsigned long temp; int n; for(n=0;nstatus & USB_ST_NOT_PROC)) { /* is not active anymore, disconnect devices */ qh_cntrl.dev_ptr=0; } } /* now process the bulk */ if(qh_bulk.dev_ptr!=0) /* it's a device assigned check if this caused IRQ */ { dev=(struct usb_device *)qh_bulk.dev_ptr; usb_get_td_status(&tmp_td[0],dev); /* update status */ if(!(dev->status & USB_ST_NOT_PROC)) { /* is not active anymore, disconnect devices */ qh_bulk.dev_ptr=0; } } } /* check the interrupt chain, ubdate the status of the appropriate device, * call the appropriate irqhandler and reactivate the TD if the irqhandler * returns with 1 */ void usb_check_int_chain(void) { int i,res; unsigned long link,status; struct usb_device *dev; uhci_td_t *td,*prevtd; for(i=0;i<8;i++) { prevtd = &td_int[i]; /* the first previous td is the skeleton td */ link=swap_32(td_int[i].link) & 0xfffffff0; /* next in chain */ td=(uhci_td_t *)link; /* assign it */ /* all interrupt TDs are finally linked to the td_int[0]. * so we process all until we find the td_int[0]. * if int0 chain points to a QH, we're also done */ while(((i>0) && (link != (unsigned long)&td_int[0])) || ((i==0) && !(swap_32(td->link) & UHCI_PTR_QH))) { /* check if a device is assigned with this td */ status=swap_32(td->status); if((td->dev_ptr!=0L) && !(status & TD_CTRL_ACTIVE)) { /* td is not active and a device is assigned -> call irqhandler */ dev=(struct usb_device *)td->dev_ptr; dev->irq_act_len=((status & 0x7FF)==0x7FF) ? 0 : (status & 0x7FF) + 1; /* transfered length */ dev->irq_status=usb_uhci_td_stat(status); /* get status */ res=dev->irq_handle(dev); /* call irqhandler */ if(res==1) { /* reactivate */ status|=TD_CTRL_ACTIVE; td->status=swap_32(status); prevtd=td; /* previous td = this td */ } else { prevtd->link=td->link; /* link previous td directly to the nex td -> unlinked */ /* remove device pointer */ td->dev_ptr=0L; } } /* if we call the irq handler */ link=swap_32(td->link) & 0xfffffff0; /* next in chain */ td=(uhci_td_t *)link; /* assign it */ } /* process all td in this int chain */ } /* next interrupt chain */ } /* usb interrupt service routine. */ void handle_usb_interrupt(void) { unsigned short status; /* * Read the interrupt status, and write it back to clear the * interrupt cause */ status = in16r(usb_base_addr + USBSTS); if (!status) /* shared interrupt, not mine */ return; if (status != 1) { /* remove host controller halted state */ if ((status&0x20) && ((in16r(usb_base_addr+USBCMD) && USBCMD_RS)==0)) { out16r(usb_base_addr + USBCMD, USBCMD_RS | in16r(usb_base_addr + USBCMD)); } } usb_check_int_chain(); /* call interrupt handlers for int tds */ usb_check_skel(); /* call completion handler for common transfer routines */ out16r(usb_base_addr+USBSTS,status); } /* init uhci */ int usb_lowlevel_init(int index, enum usb_init_type init, void **controller) { unsigned char temp; int busdevfunc; busdevfunc=pci_find_device(USB_UHCI_VEND_ID,USB_UHCI_DEV_ID,0); /* get PCI Device ID */ if(busdevfunc==-1) { printf("Error USB UHCI (%04X,%04X) not found\n",USB_UHCI_VEND_ID,USB_UHCI_DEV_ID); return -1; } pci_read_config_byte(busdevfunc,PCI_INTERRUPT_LINE,&temp); irqvec = temp; irq_free_handler(irqvec); USB_UHCI_PRINTF("Interrupt Line = %d, is %d\n",irqvec); pci_read_config_byte(busdevfunc,PCI_INTERRUPT_PIN,&temp); USB_UHCI_PRINTF("Interrupt Pin = %ld\n",temp); pci_read_config_dword(busdevfunc,PCI_BASE_ADDRESS_4,&usb_base_addr); USB_UHCI_PRINTF("IO Base Address = 0x%lx\n",usb_base_addr); usb_base_addr&=0xFFFFFFF0; usb_base_addr+=CONFIG_SYS_ISA_IO_BASE_ADDRESS; rh.devnum = 0; usb_init_skel(); reset_hc(); start_hc(); irq_install_handler(irqvec, (interrupt_handler_t *)handle_usb_interrupt, NULL); return 0; } /* stop uhci */ int usb_lowlevel_stop(int index) { if(irqvec==-1) return 1; irq_free_handler(irqvec); reset_hc(); irqvec = -1; return 0; } /******************************************************************************************* * Virtual Root Hub * Since the uhci does not have a real HUB, we simulate one ;-) */ #undef USB_RH_DEBUG #ifdef USB_RH_DEBUG #define USB_RH_PRINTF(fmt,args...) printf (fmt ,##args) static void usb_display_wValue(unsigned short wValue,unsigned short wIndex); static void usb_display_Req(unsigned short req); #else #define USB_RH_PRINTF(fmt,args...) static void usb_display_wValue(unsigned short wValue,unsigned short wIndex) {} static void usb_display_Req(unsigned short req) {} #endif #define WANT_USB_ROOT_HUB_HUB_DES #include #undef WANT_USB_ROOT_HUB_HUB_DES /* * Root Hub Control Pipe (interrupt Pipes are not supported) */ int uhci_submit_rh_msg(struct usb_device *dev, unsigned long pipe, void *buffer,int transfer_len,struct devrequest *cmd) { void *data = buffer; int leni = transfer_len; int len = 0; int status = 0; int stat = 0; int i; unsigned short cstatus; unsigned short bmRType_bReq; unsigned short wValue; unsigned short wIndex; unsigned short wLength; if (usb_pipeint(pipe)) { printf("Root-Hub submit IRQ: NOT implemented\n"); #if 0 uhci->rh.urb = urb; uhci->rh.send = 1; uhci->rh.interval = urb->interval; rh_init_int_timer (urb); #endif return 0; } bmRType_bReq = cmd->requesttype | cmd->request << 8; wValue = swap_16(cmd->value); wIndex = swap_16(cmd->index); wLength = swap_16(cmd->length); usb_display_Req(bmRType_bReq); for (i = 0; i < 8; i++) rh.c_p_r[i] = 0; USB_RH_PRINTF("Root-Hub: adr: %2x cmd(%1x): %02x%02x %04x %04x %04x\n", dev->devnum, 8, cmd->requesttype,cmd->request, wValue, wIndex, wLength); switch (bmRType_bReq) { /* Request Destination: without flags: Device, RH_INTERFACE: interface, RH_ENDPOINT: endpoint, RH_CLASS means HUB here, RH_OTHER | RH_CLASS almost ever means HUB_PORT here */ case RH_GET_STATUS: *(unsigned short *) data = swap_16(1); len=2; break; case RH_GET_STATUS | RH_INTERFACE: *(unsigned short *) data = swap_16(0); len=2; break; case RH_GET_STATUS | RH_ENDPOINT: *(unsigned short *) data = swap_16(0); len=2; break; case RH_GET_STATUS | RH_CLASS: *(unsigned long *) data = swap_32(0); len=4; break; /* hub power ** */ case RH_GET_STATUS | RH_OTHER | RH_CLASS: status = in16r(usb_base_addr + USBPORTSC1 + 2 * (wIndex - 1)); cstatus = ((status & USBPORTSC_CSC) >> (1 - 0)) | ((status & USBPORTSC_PEC) >> (3 - 1)) | (rh.c_p_r[wIndex - 1] << (0 + 4)); status = (status & USBPORTSC_CCS) | ((status & USBPORTSC_PE) >> (2 - 1)) | ((status & USBPORTSC_SUSP) >> (12 - 2)) | ((status & USBPORTSC_PR) >> (9 - 4)) | (1 << 8) | /* power on ** */ ((status & USBPORTSC_LSDA) << (-8 + 9)); *(unsigned short *) data = swap_16(status); *(unsigned short *) (data + 2) = swap_16(cstatus); len=4; break; case RH_CLEAR_FEATURE | RH_ENDPOINT: switch (wValue) { case (RH_ENDPOINT_STALL): len=0; break; } break; case RH_CLEAR_FEATURE | RH_CLASS: switch (wValue) { case (RH_C_HUB_OVER_CURRENT): len=0; /* hub power over current ** */ break; } break; case RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS: usb_display_wValue(wValue,wIndex); switch (wValue) { case (RH_PORT_ENABLE): status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1)); status = (status & 0xfff5) & ~USBPORTSC_PE; out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status); len=0; break; case (RH_PORT_SUSPEND): status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1)); status = (status & 0xfff5) & ~USBPORTSC_SUSP; out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status); len=0; break; case (RH_PORT_POWER): len=0; /* port power ** */ break; case (RH_C_PORT_CONNECTION): status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1)); status = (status & 0xfff5) | USBPORTSC_CSC; out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status); len=0; break; case (RH_C_PORT_ENABLE): status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1)); status = (status & 0xfff5) | USBPORTSC_PEC; out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status); len=0; break; case (RH_C_PORT_SUSPEND): /*** WR_RH_PORTSTAT(RH_PS_PSSC); */ len=0; break; case (RH_C_PORT_OVER_CURRENT): len=0; break; case (RH_C_PORT_RESET): rh.c_p_r[wIndex - 1] = 0; len=0; break; } break; case RH_SET_FEATURE | RH_OTHER | RH_CLASS: usb_display_wValue(wValue,wIndex); switch (wValue) { case (RH_PORT_SUSPEND): status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1)); status = (status & 0xfff5) | USBPORTSC_SUSP; out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status); len=0; break; case (RH_PORT_RESET): status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1)); status = (status & 0xfff5) | USBPORTSC_PR; out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status); mdelay(10); status = (status & 0xfff5) & ~USBPORTSC_PR; out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status); udelay(10); status = (status & 0xfff5) | USBPORTSC_PE; out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status); mdelay(10); status = (status & 0xfff5) | 0xa; out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status); len=0; break; case (RH_PORT_POWER): len=0; /* port power ** */ break; case (RH_PORT_ENABLE): status = in16r(usb_base_addr+USBPORTSC1+2*(wIndex-1)); status = (status & 0xfff5) | USBPORTSC_PE; out16r(usb_base_addr+USBPORTSC1+2*(wIndex-1),status); len=0; break; } break; case RH_SET_ADDRESS: rh.devnum = wValue; len=0; break; case RH_GET_DESCRIPTOR: switch ((wValue & 0xff00) >> 8) { case (0x01): /* device descriptor */ i=sizeof(root_hub_config_des); status=i > wLength ? wLength : i; len = leni > status ? status : leni; memcpy (data, root_hub_dev_des, len); break; case (0x02): /* configuration descriptor */ i=sizeof(root_hub_config_des); status=i > wLength ? wLength : i; len = leni > status ? status : leni; memcpy (data, root_hub_config_des, len); break; case (0x03): /*string descriptors */ if(wValue==0x0300) { i=sizeof(root_hub_str_index0); status = i > wLength ? wLength : i; len = leni > status ? status : leni; memcpy (data, root_hub_str_index0, len); break; } if(wValue==0x0301) { i=sizeof(root_hub_str_index1); status = i > wLength ? wLength : i; len = leni > status ? status : leni; memcpy (data, root_hub_str_index1, len); break; } stat = USB_ST_STALLED; } break; case RH_GET_DESCRIPTOR | RH_CLASS: root_hub_hub_des[2] = 2; i=sizeof(root_hub_hub_des); status= i > wLength ? wLength : i; len = leni > status ? status : leni; memcpy (data, root_hub_hub_des, len); break; case RH_GET_CONFIGURATION: *(unsigned char *) data = 0x01; len = 1; break; case RH_SET_CONFIGURATION: len=0; break; default: stat = USB_ST_STALLED; } USB_RH_PRINTF("Root-Hub stat %lx port1: %x port2: %x\n\n",stat, in16r(usb_base_addr + USBPORTSC1), in16r(usb_base_addr + USBPORTSC2)); dev->act_len=len; dev->status=stat; return stat; } /******************************************************************************** * Some Debug Routines */ #ifdef USB_RH_DEBUG static void usb_display_Req(unsigned short req) { USB_RH_PRINTF("- Root-Hub Request: "); switch (req) { case RH_GET_STATUS: USB_RH_PRINTF("Get Status "); break; case RH_GET_STATUS | RH_INTERFACE: USB_RH_PRINTF("Get Status Interface "); break; case RH_GET_STATUS | RH_ENDPOINT: USB_RH_PRINTF("Get Status Endpoint "); break; case RH_GET_STATUS | RH_CLASS: USB_RH_PRINTF("Get Status Class"); break; /* hub power ** */ case RH_GET_STATUS | RH_OTHER | RH_CLASS: USB_RH_PRINTF("Get Status Class Others"); break; case RH_CLEAR_FEATURE | RH_ENDPOINT: USB_RH_PRINTF("Clear Feature Endpoint "); break; case RH_CLEAR_FEATURE | RH_CLASS: USB_RH_PRINTF("Clear Feature Class "); break; case RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS: USB_RH_PRINTF("Clear Feature Other Class "); break; case RH_SET_FEATURE | RH_OTHER | RH_CLASS: USB_RH_PRINTF("Set Feature Other Class "); break; case RH_SET_ADDRESS: USB_RH_PRINTF("Set Address "); break; case RH_GET_DESCRIPTOR: USB_RH_PRINTF("Get Descriptor "); break; case RH_GET_DESCRIPTOR | RH_CLASS: USB_RH_PRINTF("Get Descriptor Class "); break; case RH_GET_CONFIGURATION: USB_RH_PRINTF("Get Configuration "); break; case RH_SET_CONFIGURATION: USB_RH_PRINTF("Get Configuration "); break; default: USB_RH_PRINTF("****UNKNOWN**** 0x%04X ",req); } USB_RH_PRINTF("\n"); } static void usb_display_wValue(unsigned short wValue,unsigned short wIndex) { switch (wValue) { case (RH_PORT_ENABLE): USB_RH_PRINTF("Root-Hub: Enable Port %d\n",wIndex); break; case (RH_PORT_SUSPEND): USB_RH_PRINTF("Root-Hub: Suspend Port %d\n",wIndex); break; case (RH_PORT_POWER): USB_RH_PRINTF("Root-Hub: Port Power %d\n",wIndex); break; case (RH_C_PORT_CONNECTION): USB_RH_PRINTF("Root-Hub: C Port Connection Port %d\n",wIndex); break; case (RH_C_PORT_ENABLE): USB_RH_PRINTF("Root-Hub: C Port Enable Port %d\n",wIndex); break; case (RH_C_PORT_SUSPEND): USB_RH_PRINTF("Root-Hub: C Port Suspend Port %d\n",wIndex); break; case (RH_C_PORT_OVER_CURRENT): USB_RH_PRINTF("Root-Hub: C Port Over Current Port %d\n",wIndex); break; case (RH_C_PORT_RESET): USB_RH_PRINTF("Root-Hub: C Port reset Port %d\n",wIndex); break; default: USB_RH_PRINTF("Root-Hub: unknown %x %x\n",wValue,wIndex); break; } } #endif #ifdef USB_UHCI_DEBUG static int usb_display_td(uhci_td_t *td) { unsigned long tmp; int valid; printf("TD at %p:\n",td); tmp=swap_32(td->link); printf("Link points to 0x%08lX, %s first, %s, %s\n",tmp&0xfffffff0, ((tmp & 0x4)==0x4) ? "Depth" : "Breath", ((tmp & 0x2)==0x2) ? "QH" : "TD", ((tmp & 0x1)==0x1) ? "invalid" : "valid"); valid=((tmp & 0x1)==0x0); tmp=swap_32(td->status); printf(" %s %ld Errors %s %s %s \n %s %s %s %s %s %s\n Len 0x%lX\n", (((tmp>>29)&0x1)==0x1) ? "SPD Enable" : "SPD Disable", ((tmp>>28)&0x3), (((tmp>>26)&0x1)==0x1) ? "Low Speed" : "Full Speed", (((tmp>>25)&0x1)==0x1) ? "ISO " : "", (((tmp>>24)&0x1)==0x1) ? "IOC " : "", (((tmp>>23)&0x1)==0x1) ? "Active " : "Inactive ", (((tmp>>22)&0x1)==0x1) ? "Stalled" : "", (((tmp>>21)&0x1)==0x1) ? "Data Buffer Error" : "", (((tmp>>20)&0x1)==0x1) ? "Babble" : "", (((tmp>>19)&0x1)==0x1) ? "NAK" : "", (((tmp>>18)&0x1)==0x1) ? "Bitstuff Error" : "", (tmp&0x7ff)); tmp=swap_32(td->info); printf(" MaxLen 0x%lX\n",((tmp>>21)&0x7FF)); printf(" %s Endpoint 0x%lX Dev Addr 0x%lX PID 0x%lX\n",((tmp>>19)&0x1)==0x1 ? "TOGGLE" : "", ((tmp>>15)&0xF),((tmp>>8)&0x7F),tmp&0xFF); tmp=swap_32(td->buffer); printf(" Buffer 0x%08lX\n",tmp); printf(" DEV %08lX\n",td->dev_ptr); return valid; } void usb_show_td(int max) { int i; if(max>0) { for(i=0;i