; General settings that can be overwritten in the host code
; that calls the AISGen library.
[General]

; Can be 8 or 16 - used in emifa
busWidth=8

; SPIMASTER,I2CMASTER,EMIFA,NAND,EMAC,UART,PCI,HPI,USB,MMC_SD,VLYNQ,RAW
BootMode=UART

; 8,16,24 - used for SPI,I2C
;AddrWidth=8

; NO_CRC,SECTION_CRC,SINGLE_CRC
crcCheckType=NO_CRC

; This section allows setting the PLL0 system clock with a
; specified multiplier and divider as shown. The clock source
; can also be chosen for internal or external.
;           |------24|------16|-------8|-------0|
; PLL0CFG0: | CLKMODE| PLLM   | PREDIV | POSTDIV|
; PLL0CFG1: | RSVD   | PLLDIV1| PLLDIV3| PLLDIV7|
;[PLL0CONFIG]
;PLL0CFG0 = 0x00180001
;PLL0CFG1 = 0x00000205

[PLLANDCLOCKCONFIG]
PLL0CFG0 = 0x00180001
PLL0CFG1 = 0x00000205
PERIPHCLKCFG = 0x00000051

; This section allows setting up the PLL1. Usually this will
; take place as part of the EMIF3a DDR setup. The format of
; the input args is as follows:
;           |------24|------16|-------8|-------0|
; PLL1CFG0: |    PLLM| POSTDIV| PLLDIV1| PLLDIV2|
; PLL1CFG1: |           RSVD           | PLLDIV3|
[PLL1CONFIG]
PLL1CFG0 = 0x18010001
PLL1CFG1 = 0x00000002

; This section lets us configure the peripheral interface
; of the current booting peripheral (I2C, SPI, or UART).
; Use with caution. The format of the PERIPHCLKCFG field
; is as follows:
; SPI:        |------24|------16|-------8|-------0|
;             |           RSVD           |PRESCALE|
;
; I2C:        |------24|------16|-------8|-------0|
;             |  RSVD  |PRESCALE|  CLKL  |  CLKH  |
;
; UART:       |------24|------16|-------8|-------0|
;             | RSVD   |  OSR   |  DLH   |  DLL   |
[PERIPHCLKCFG]
PERIPHCLKCFG = 0x00000051

; This section can be used to configure the PLL1 and the EMIF3a registers
; for starting the DDR2 interface.
; See PLL1CONFIG section for the format of the PLL1CFG fields.
;            |------24|------16|-------8|-------0|
; PLL1CFG0:  |              PLL1CFG              |
; PLL1CFG1:  |              PLL1CFG              |
; DDRPHYC1R: |             DDRPHYC1R             |
; SDCR:      |              SDCR                 |
; SDTIMR:    |              SDTIMR               |
; SDTIMR2:   |              SDTIMR2              |
; SDRCR:     |              SDRCR                |
; CLK2XSRC:  |             CLK2XSRC              |
[EMIF3DDR]
PLL1CFG0 = 0x18010001
PLL1CFG1 = 0x00000002
DDRPHYC1R = 0x000000C2
SDCR = 0x0017C432
SDTIMR = 0x26922A09
SDTIMR2 = 0x4414C722
SDRCR = 0x00000498
CLK2XSRC = 0x00000000

; This section can be used to configure the EMIFA to use
; CS0 as an SDRAM interface.  The fields required to do this
; are given below.
;                     |------24|------16|-------8|-------0|
; SDBCR:              |               SDBCR               |
; SDTIMR:             |               SDTIMR              |
; SDRSRPDEXIT:        |             SDRSRPDEXIT           |
; SDRCR:              |               SDRCR               |
; DIV4p5_CLK_ENABLE:  |         DIV4p5_CLK_ENABLE         |
;[EMIF25SDRAM]
;SDBCR = 0x00004421
;SDTIMR = 0x42215810
;SDRSRPDEXIT = 0x00000009
;SDRCR = 0x00000410
;DIV4p5_CLK_ENABLE = 0x00000001

; This section can be used to configure the async chip selects
; of the EMIFA (CS2-CS5).  The fields required to do this
; are given below.
;           |------24|------16|-------8|-------0|
; A1CR:     |                A1CR               |
; A2CR:     |                A2CR               |
; A3CR:     |                A3CR               |
; A4CR:     |                A4CR               |
; NANDFCR:  |              NANDFCR              |
;[EMIF25ASYNC]
;A1CR = 0x00000000
;A2CR = 0x00000000
;A3CR = 0x00000000
;A4CR = 0x00000000
;NANDFCR = 0x00000000
[EMIF25ASYNC]
A1CR = 0x00000000
A2CR = 0x04202110
A3CR = 0x00000000
A4CR = 0x00000000
NANDFCR = 0x00000012

; This section should be used in place of PLL0CONFIG when
; the I2C, SPI, or UART modes are being used.  This ensures that
; the system PLL and the peripheral's clocks are changed together.
; See PLL0CONFIG section for the format of the PLL0CFG fields.
; See PERIPHCLKCFG section for the format of the CLKCFG field.
;               |------24|------16|-------8|-------0|
; PLL0CFG0:     |              PLL0CFG              |
; PLL0CFG1:     |              PLL0CFG              |
; PERIPHCLKCFG: |              CLKCFG               |
;[PLLANDCLOCKCONFIG]
;PLL0CFG0 = 0x00180001
;PLL0CFG1 = 0x00000205
;PERIPHCLKCFG = 0x00010032

; This section should be used to setup the power state of modules
; of the two PSCs.  This section can be included multiple times to
; allow the configuration of any or all of the device modules.
;           |------24|------16|-------8|-------0|
; LPSCCFG:  | PSCNUM | MODULE |   PD   | STATE  |
;[PSCCONFIG]
;LPSCCFG=

; This section allows setting of a single PINMUX register.
; This section can be included multiple times to allow setting
; as many PINMUX registers as needed.
;         |------24|------16|-------8|-------0|
; REGNUM: |              regNum               |
; MASK:   |               mask                |
; VALUE:  |              value                |
;[PINMUX]
;REGNUM = 5
;MASK = 0x00FF0000
;VALUE = 0x00880000

; No Params required - simply include this section for the fast boot
; function to be called
;[FASTBOOT]

; This section allows setting up the PLL1. Usually this will
; take place as part of the EMIF3a DDR setup. The format of
; the input args is as follows:
;           |------24|------16|-------8|-------0|
; PLL1CFG0: |    PLLM| POSTDIV| PLLDIV1| PLLDIV2|
; PLL1CFG1: |           RSVD           | PLLDIV3|
;[PLL1CONFIG]
;PLL1CFG0 = 0x15010001
;PLL1CFG1 = 0x00000002

; This section can be used to configure the PLL1 and the EMIF3a registers
; for starting the DDR2 interface on ARM-boot D800K002 devices.
;            |------24|------16|-------8|-------0|
; DDRPHYC1R: |             DDRPHYC1R             |
; SDCR:      |              SDCR                 |
; SDTIMR:    |              SDTIMR               |
; SDTIMR2:   |              SDTIMR2              |
; SDRCR:     |              SDRCR                |
; CLK2XSRC:  |             CLK2XSRC              |
;[ARM_EMIF3DDR_PATCHFXN]
;DDRPHYC1R = 0x000000C2
;SDCR = 0x0017C432
;SDTIMR = 0x26922A09
;SDTIMR2 = 0x4414C722
;SDRCR = 0x00000498
;CLK2XSRC = 0x00000000

; This section can be used to configure the PLL1 and the EMIF3a registers
; for starting the DDR2 interface on DSP-boot D800K002 devices.
;            |------24|------16|-------8|-------0|
; DDRPHYC1R: |             DDRPHYC1R             |
; SDCR:      |              SDCR                 |
; SDTIMR:    |              SDTIMR               |
; SDTIMR2:   |              SDTIMR2              |
; SDRCR:     |              SDRCR                |
; CLK2XSRC:  |             CLK2XSRC              |
;[DSP_EMIF3DDR_PATCHFXN]
;DDRPHYC1R = 0x000000C4
;SDCR = 0x08134632
;SDTIMR = 0x26922A09
;SDTIMR2 = 0x0014C722
;SDRCR = 0x00000492
;CLK2XSRC = 0x00000000

;[INPUTFILE]
;FILENAME=u-boot.bin
;LOADADDRESS=0xC1080000
;ENTRYPOINTADDRESS=0xC1080000