From cf6f469e2730fc8ab3523808b828be000d6eee77 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Sun, 1 Jun 2008 09:09:48 -0400 Subject: Blackfin: unify common ADI board settings Rather than duplicate the same ADI settings in every ADI board, create a common ADI config header and have all ADI boards start using that. This will also make merging the ~10 boards I have to forward port a lot easier. Signed-off-by: Mike Frysinger --- include/configs/bf533-ezkit.h | 286 ++++++++++-------------- include/configs/bf533-stamp.h | 436 ++++++++++++------------------------- include/configs/bf537-stamp.h | 441 ++++++++++++++------------------------ include/configs/bf561-ezkit.h | 295 ++++++++++--------------- include/configs/bfin_adi_common.h | 198 +++++++++++++++++ 5 files changed, 719 insertions(+), 937 deletions(-) create mode 100644 include/configs/bfin_adi_common.h (limited to 'include/configs') diff --git a/include/configs/bf533-ezkit.h b/include/configs/bf533-ezkit.h index 48c0252e46..eb0889078b 100644 --- a/include/configs/bf533-ezkit.h +++ b/include/configs/bf533-ezkit.h @@ -2,213 +2,155 @@ * U-boot - Configuration file for BF533 EZKIT board */ -#ifndef __CONFIG_EZKIT533_H__ -#define __CONFIG_EZKIT533_H__ +#ifndef __CONFIG_BF533_EZKIT_H__ +#define __CONFIG_BF533_EZKIT_H__ #include -#define CONFIG_BAUDRATE 57600 -#define CONFIG_BOOTDELAY 5 -#define CONFIG_SYS_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */ +/* + * Processor Settings + */ +#define CONFIG_BFIN_CPU bf533-0.3 +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS -#define CONFIG_SYS_LONGHELP 1 -#define CONFIG_CMDLINE_EDITING 1 -#define CONFIG_LOADADDR 0x01000000 /* default load address */ -#define CONFIG_BOOTCOMMAND "tftp $(loadaddr) linux" -/* #define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw" */ -#define CONFIG_DRIVER_SMC91111 1 -#define CONFIG_SMC91111_BASE 0x20310300 +/* + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV + */ +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 27000000 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 22 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 5 -#if 0 -#define CONFIG_MII -#define CONFIG_SYS_DISCOVER_PHY -#endif -#define CONFIG_RTC_BFIN 1 -#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */ - -#define CONFIG_PANIC_HANG 1 - -#define CONFIG_BFIN_CPU bf533-0.3 -#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS - -/* This sets the default state of the cache on U-Boot's boot */ -#define CONFIG_ICACHE_ON -#define CONFIG_DCACHE_ON - -/* CONFIG_CLKIN_HZ is any value in Hz */ -#define CONFIG_CLKIN_HZ 27000000 -/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ -/* 1=CLKIN/2 */ -#define CONFIG_CLKIN_HALF 0 -/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ -/* 1=bypass PLL */ -#define CONFIG_PLL_BYPASS 0 -/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */ -/* Values can range from 1-64 */ -#define CONFIG_VCO_MULT 22 -/* CONFIG_CCLK_DIV controls what the core clock divider is */ -/* Values can be 1, 2, 4, or 8 ONLY */ -#define CONFIG_CCLK_DIV 1 -/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */ -/* Values can range from 1-15 */ -#define CONFIG_SCLK_DIV 5 -/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ -/* Values can range from 2-65535 */ -/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ -#define CONFIG_SPI_BAUD 2 -#define CONFIG_SPI_BAUD_INITBLOCK 4 - -#if ( CONFIG_CLKIN_HALF == 0 ) -#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) +/* + * Memory Settings + */ +#define CONFIG_MEM_SIZE 32 +/* Early EZKITs had 32megs, but later have 64megs */ +#if (CONFIG_MEM_SIZE == 64) +# define CONFIG_MEM_ADD_WDTH 10 #else -#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) +# define CONFIG_MEM_ADD_WDTH 9 #endif -#if (CONFIG_PLL_BYPASS == 0) -#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) -#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) -#else -#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ -#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ -#endif +#define CONFIG_EBIU_SDRRC_VAL 0x398 +#define CONFIG_EBIU_SDGCTL_VAL 0x91118d -#define CONFIG_MEM_SIZE 32 /* 128, 64, 32, 16 */ -#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */ -#define CONFIG_MEM_MT48LC16M16A2TG_75 1 +#define CONFIG_EBIU_AMGCTL_VAL 0xFF +#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 +#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 -#define CONFIG_LOADS_ECHO 1 +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* - * BOOTP options + * Network Settings */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME +#define ADI_CMDS_NETWORK 1 +#define CONFIG_DRIVER_SMC91111 1 +#define CONFIG_SMC91111_BASE 0x20310300 +#define SMC91111_EEPROM_INIT() \ + do { \ + *pFIO_DIR |= PF1; \ + *pFIO_FLAG_S = PF1; \ + SSYNC(); \ + } while (0) +#define CONFIG_HOSTNAME bf533-ezkit +/* Uncomment next line to use fixed MAC address */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */ /* - * Command line configuration. + * Flash Settings */ -#include - -#define CONFIG_CMD_PING -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_DATE - - -#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600" - -#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024 * 1024) /* 1 ... 31 MB in DRAM */ -#define CONFIG_SYS_LOAD_ADDR 0x01000000 /* default load address */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024) #define CONFIG_SYS_FLASH_BASE 0x20000000 - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN) -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) -#define CONFIG_SYS_GBL_DATA_SIZE 0x4000 -#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4) - -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -#define CONFIG_SYS_FLASH0_BASE 0x20000000 -#define CONFIG_SYS_FLASH1_BASE 0x20200000 -#define CONFIG_SYS_FLASH2_BASE 0x20280000 -#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 40 /* max number of sectors on one chip */ - -#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_SYS_MAX_FLASH_BANKS 3 +#define CONFIG_SYS_MAX_FLASH_SECT 40 +#define CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_ADDR 0x20020000 -#define CONFIG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */ - -/* JFFS Partition offset set */ -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 -/* 512k reserved for u-boot */ -#define CONFIG_SYS_JFFS2_FIRST_SECTOR 11 - - -/* - * Stack sizes - */ -#define CONFIG_STACKSIZE (128*1024) /* regular stack */ - -#define POLL_MODE 1 +#define CONFIG_ENV_SECT_SIZE 0x10000 #define FLASH_TOT_SECT 40 -#define FLASH_SIZE 0x220000 -#define CONFIG_SYS_FLASH_SIZE 0x220000 -/* - * Initialize PSD4256 registers for using I2C - */ -#define CONFIG_MISC_INIT_R /* - * I2C settings + * I2C Settings * By default PF1 is used as SDA and PF0 as SCL on the Stamp board */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -/* - * Software (bit-bang) I2C driver configuration - */ -#define PF_SCL PF0 -#define PF_SDA PF1 - -#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;") -#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;") -#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;") -#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;") -#define I2C_SDA(bit) if(bit) { \ - *pFIO_FLAG_S = PF_SDA; \ - asm("ssync;"); \ - } \ - else { \ - *pFIO_FLAG_C = PF_SDA; \ - asm("ssync;"); \ - } -#define I2C_SCL(bit) if(bit) { \ - *pFIO_FLAG_S = PF_SCL; \ - asm("ssync;"); \ - } \ - else { \ - *pFIO_FLAG_C = PF_SCL; \ - asm("ssync;"); \ - } -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ +#define CONFIG_SOFT_I2C +#ifdef CONFIG_SOFT_I2C +#define PF_SCL PF0 +#define PF_SDA PF1 +#define I2C_INIT \ + do { \ + *pFIO_DIR |= PF_SCL; \ + SSYNC(); \ + } while (0) +#define I2C_ACTIVE \ + do { \ + *pFIO_DIR |= PF_SDA; \ + *pFIO_INEN &= ~PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_TRISTATE \ + do { \ + *pFIO_DIR &= ~PF_SDA; \ + *pFIO_INEN |= PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0) +#define I2C_SDA(bit) \ + do { \ + if (bit) \ + *pFIO_FLAG_S = PF_SDA; \ + else \ + *pFIO_FLAG_C = PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_SCL(bit) \ + do { \ + if (bit) \ + *pFIO_FLAG_S = PF_SCL; \ + else \ + *pFIO_FLAG_C = PF_SCL; \ + SSYNC(); \ + } while (0) +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ #define CONFIG_SYS_I2C_SPEED 50000 #define CONFIG_SYS_I2C_SLAVE 0 +#endif -#define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */ -#define CONFIG_EBIU_SDRRC_VAL 0x398 -#define CONFIG_EBIU_SDGCTL_VAL 0x91118d -#define CONFIG_EBIU_SDBCTL_VAL 0x13 +/* + * Misc Settings + */ +#define CONFIG_MISC_INIT_R +#define CONFIG_RTC_BFIN +#define CONFIG_UART_CONSOLE 0 + -#define CONFIG_EBIU_AMGCTL_VAL 0xFF -#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 -#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 +/* + * Pull in common ADI header for remaining command/environment setup + */ +#include #include diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h index ee41c7e78f..622f54c38c 100644 --- a/include/configs/bf533-stamp.h +++ b/include/configs/bf533-stamp.h @@ -2,371 +2,219 @@ * U-boot - Configuration file for BF533 STAMP board */ -#ifndef __CONFIG_STAMP_H__ -#define __CONFIG_STAMP_H__ +#ifndef __CONFIG_BF533_STAMP_H__ +#define __CONFIG_BF533_STAMP_H__ #include -#define CONFIG_RTC_BFIN 1 - -#define CONFIG_PANIC_HANG 1 - -#define CONFIG_BFIN_CPU bf533-0.3 -#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS - -/* This sets the default state of the cache on U-Boot's boot */ -#define CONFIG_ICACHE_ON -#define CONFIG_DCACHE_ON /* - * Board settings + * Processor Settings */ -#define CONFIG_DRIVER_SMC91111 1 -#define CONFIG_SMC91111_BASE 0x20300300 - -/* FLASH/ETHERNET uses the same address range */ -#define SHARED_RESOURCES 1 +#define CONFIG_BFIN_CPU bf533-0.3 +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS -/* Is I2C bit-banged? */ -#define CONFIG_SOFT_I2C 1 /* - * Software (bit-bang) I2C driver configuration + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV */ -#define PF_SCL PF3 -#define PF_SDA PF2 +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 11059200 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 36 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 5 -/* - * Video splash screen support - */ -#define CONFIG_VIDEO 0 /* - * Clock settings + * Memory Settings */ +#define CONFIG_MEM_ADD_WDTH 11 +#define CONFIG_MEM_SIZE 128 -/* CONFIG_CLKIN_HZ is any value in Hz */ -#define CONFIG_CLKIN_HZ 11059200 -/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ -/* 1=CLKIN/2 */ -#define CONFIG_CLKIN_HALF 0 -/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ -/* 1=bypass PLL */ -#define CONFIG_PLL_BYPASS 0 -/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */ -/* Values can range from 1-64 */ -#define CONFIG_VCO_MULT 36 -/* CONFIG_CCLK_DIV controls what the core clock divider is */ -/* Values can be 1, 2, 4, or 8 ONLY */ -#define CONFIG_CCLK_DIV 1 -/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/ -/* Values can range from 1-15 */ -#define CONFIG_SCLK_DIV 5 -/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ -/* Values can range from 2-65535 */ -/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ -#define CONFIG_SPI_BAUD 2 -#define CONFIG_SPI_BAUD_INITBLOCK 4 - -/* - * Network settings - */ +#define CONFIG_EBIU_SDRRC_VAL 0x268 +#define CONFIG_EBIU_SDGCTL_VAL 0x911109 -#if (CONFIG_DRIVER_SMC91111) -#if 0 -#define CONFIG_MII -#endif +#define CONFIG_EBIU_AMGCTL_VAL 0xFF +#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3 +#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983 -/* network support */ -#define CONFIG_IPADDR 192.168.0.15 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_GATEWAYIP 192.168.0.1 -#define CONFIG_SERVERIP 192.168.0.2 -#define CONFIG_HOSTNAME STAMP -#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MALLOC_LEN (384 * 1024) -/* To remove hardcoding and enable MAC storage in EEPROM */ -/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */ -#endif /* CONFIG_DRIVER_SMC91111 */ /* - * Flash settings + * Network Settings */ +#define ADI_CMDS_NETWORK 1 +#define CONFIG_DRIVER_SMC91111 1 +#define CONFIG_SMC91111_BASE 0x20300300 +#define SMC91111_EEPROM_INIT() \ + do { \ + *pFIO_DIR |= PF1; \ + *pFIO_FLAG_S = PF1; \ + SSYNC(); \ + } while (0) +#define CONFIG_HOSTNAME bf533-stamp +/* Uncomment next line to use fixed MAC address */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI_AMD_RESET - -#define CONFIG_SYS_FLASH_BASE 0x20000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ - -#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) -#define CONFIG_ENV_IS_IN_EEPROM 1 -#define CONFIG_ENV_OFFSET 0x4000 -#define CONFIG_ENV_HEADER (CONFIG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */ -#else -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0x20004000 -#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) -#endif - -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */ -#define ENV_IS_EMBEDDED - -#define CONFIG_SYS_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */ -#define CONFIG_SYS_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */ - -/* JFFS Partition offset set */ -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 -/* 512k reserved for u-boot */ -#define CONFIG_SYS_JFFS2_FIRST_SECTOR 11 - -/* - * following timeouts shall be used once the - * Flash real protection is enabled - */ -#define CONFIG_SYS_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */ -#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */ - -/* - * SDRAM settings & memory map - */ - -#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */ -#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */ -#define CONFIG_MEM_MT48LC64M4A2FB_7E 1 - -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 *1024) -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MAX_RAM_SIZE - 0x80000 - 1) -#define CONFIG_LOADADDR 0x01000000 - -#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_GBL_DATA_SIZE 0x4000 /* Reserve 16k for Global Data */ -#define CONFIG_STACKSIZE (128*1024) /* regular stack */ - -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - 0x40000) -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) -#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4) - -/* Check to make sure everything fits in SDRAM */ -#if ((CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) > CONFIG_SYS_MAX_RAM_SIZE) - #error Memory Map does not fit into configuration -#endif - -#if ( CONFIG_CLKIN_HALF == 0 ) -#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) -#else -#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) -#endif - -#if (CONFIG_PLL_BYPASS == 0) -#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) -#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) -#else -#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ -#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ -#endif /* - * Command settings + * Flash Settings */ - -#define CONFIG_SYS_LONGHELP 1 -#define CONFIG_CMDLINE_EDITING 1 - -#define CONFIG_SYS_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */ - -/* configuration lookup from the BOOTP/DHCP server, */ -/* but not try to load any image using TFTP */ - -#define CONFIG_BOOTDELAY 5 -#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */ -#define CONFIG_BOOTCOMMAND "run ramboot" - -#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600" - - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \ - "$(rootpath) console=ttyBF0,57600\0" \ - "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ - "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \ - "ramboot=tftpboot $(loadaddr) linux; " \ - "run ramargs;run addip;bootelf\0" \ - "nfsboot=tftpboot $(loadaddr) linux; " \ - "run nfsargs;run addip;bootelf\0" \ - "flashboot=bootm 0x20100000\0" \ - "update=tftpboot $(loadaddr) u-boot.bin; " \ - "protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \ - "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \ - "" - -#ifdef CONFIG_SOFT_I2C -#if (!CONFIG_SOFT_I2C) -#undef CONFIG_SOFT_I2C -#endif -#endif +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_BASE 0x20000000 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_CFI_AMD_RESET +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 67 /* - * BOOTP options + * SPI Settings */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BFIN_SPI +#define CONFIG_ENV_SPI_MAX_HZ 30000000 +#define CONFIG_SF_DEFAULT_HZ 30000000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_ATMEL +#define CONFIG_SPI_FLASH_SPANSION +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SPI_FLASH_WINBOND /* - * Command line configuration. + * Env Storage Settings */ -#include - -#define CONFIG_CMD_ELF -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_DATE - -#if (CONFIG_DRIVER_SMC91111) -#define CONFIG_CMD_PING -#endif - -#if (CONFIG_SOFT_I2C) -#define CONFIG_CMD_I2C +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 #endif - -#define CONFIG_CMD_DHCP - - -/* - * Console settings - */ - -#define CONFIG_BAUDRATE 57600 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) +#define ENV_IS_EMBEDDED #else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define ENV_IS_EMBEDDED_CUSTOM #endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_LOADS_ECHO 1 /* - * I2C settings + * I2C Settings * By default PF2 is used as SDA and PF3 as SCL on the Stamp board */ -#if (CONFIG_SOFT_I2C) - -#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;") -#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;") -#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;") -#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;") -#define I2C_SDA(bit) if(bit) { \ - *pFIO_FLAG_S = PF_SDA; \ - asm("ssync;"); \ - } \ - else { \ - *pFIO_FLAG_C = PF_SDA; \ - asm("ssync;"); \ - } -#define I2C_SCL(bit) if(bit) { \ - *pFIO_FLAG_S = PF_SCL; \ - asm("ssync;"); \ - } \ - else { \ - *pFIO_FLAG_C = PF_SCL; \ - asm("ssync;"); \ - } +#define CONFIG_SOFT_I2C +#ifdef CONFIG_SOFT_I2C +#define PF_SCL PF3 +#define PF_SDA PF2 +#define I2C_INIT \ + do { \ + *pFIO_DIR |= PF_SCL; \ + SSYNC(); \ + } while (0) +#define I2C_ACTIVE \ + do { \ + *pFIO_DIR |= PF_SDA; \ + *pFIO_INEN &= ~PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_TRISTATE \ + do { \ + *pFIO_DIR &= ~PF_SDA; \ + *pFIO_INEN |= PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0) +#define I2C_SDA(bit) \ + do { \ + if (bit) \ + *pFIO_FLAG_S = PF_SDA; \ + else \ + *pFIO_FLAG_C = PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_SCL(bit) \ + do { \ + if (bit) \ + *pFIO_FLAG_S = PF_SCL; \ + else \ + *pFIO_FLAG_C = PF_SCL; \ + SSYNC(); \ + } while (0) #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ #define CONFIG_SYS_I2C_SPEED 50000 #define CONFIG_SYS_I2C_SLAVE 0 -#endif /* CONFIG_SOFT_I2C */ +#endif + /* - * Compact Flash settings + * Compact Flash / IDE / ATA Settings */ /* Enabled below option for CF support */ -/* #define CONFIG_STAMP_CF 1 */ - -#if defined(CONFIG_STAMP_CF) && defined(CONFIG_CMD_IDE) - -#define CONFIG_MISC_INIT_R 1 +/* #define CONFIG_STAMP_CF */ +#if defined(CONFIG_STAMP_CF) +#define CONFIG_MISC_INIT_R #define CONFIG_DOS_PARTITION 1 -/* - * IDE/ATA stuff - */ #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ #undef CONFIG_IDE_LED /* no led for ide supported */ #undef CONFIG_IDE_RESET /* no reset for ide supported */ -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ -#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1) #define CONFIG_SYS_ATA_BASE_ADDR 0x20200000 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* alternate registers */ #define CONFIG_SYS_ATA_STRIDE 2 + +#undef CONFIG_EBIU_AMBCTL1_VAL +#define CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2 #endif + /* - * Miscellaneous configurable options + * Misc Settings */ +#define CONFIG_RTC_BFIN +#define CONFIG_UART_CONSOLE 0 -#define CONFIG_SYS_HZ 1000 /* 1ms time tick */ - -#define CONFIG_SYS_BOOTM_LEN 0x4000000/* Large Image Length, set to 64 Meg */ - -#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */ +/* FLASH/ETHERNET uses the same async bank */ +#define SHARED_RESOURCES 1 -#define CONFIG_SPI +/* define to enable splash screen support */ +/* #define CONFIG_VIDEO */ -#ifdef CONFIG_VIDEO -#if (CONFIG_VIDEO) -#define CONFIG_SPLASH_SCREEN 1 -#define CONFIG_SILENT_CONSOLE 1 -#else -#undef CONFIG_VIDEO -#endif -#endif /* - * FLASH organization and environment definitions + * Pull in common ADI header for remaining command/environment setup */ - -#define CONFIG_EBIU_SDRRC_VAL 0x268 -#define CONFIG_EBIU_SDGCTL_VAL 0x911109 -#define CONFIG_EBIU_SDBCTL_VAL 0x37 - -#define CONFIG_EBIU_AMGCTL_VAL 0xFF -#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3 -#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983 -#define CF_CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2 +#include #include diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h index f6399a9f52..7c35a022f9 100644 --- a/include/configs/bf537-stamp.h +++ b/include/configs/bf537-stamp.h @@ -2,272 +2,144 @@ * U-boot - Configuration file for BF537 STAMP board */ -#ifndef __CONFIG_BF537_H__ -#define __CONFIG_BF537_H__ +#ifndef __CONFIG_BF537_STAMP_H__ +#define __CONFIG_BF537_STAMP_H__ #include -#define CONFIG_SYS_LONGHELP 1 -#define CONFIG_CMDLINE_EDITING 1 -#define CONFIG_BAUDRATE 57600 -/* Set default serial console for bf537 */ -#define CONFIG_UART_CONSOLE 0 -#define CONFIG_BOOTDELAY 5 -/* define CONFIG_BF537_STAMP_LEDCMD to enable LED command*/ -/*#define CONFIG_BF537_STAMP_LEDCMD 1*/ - -#define CONFIG_PANIC_HANG 1 -#define CONFIG_BFIN_CPU bf537-0.2 -#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS - -#define CONFIG_BFIN_MAC +/* + * Processor Settings + */ +#define CONFIG_BFIN_CPU bf537-0.2 +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS -/* This sets the default state of the cache on U-Boot's boot */ -#define CONFIG_ICACHE_ON -#define CONFIG_DCACHE_ON -/* Define if want to do post memory test */ -#undef CONFIG_POST_TEST - -#define CONFIG_RTC_BFIN 1 -#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */ - -/* CONFIG_CLKIN_HZ is any value in Hz */ -#define CONFIG_CLKIN_HZ 25000000 -/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ -/* 1=CLKIN/2 */ -#define CONFIG_CLKIN_HALF 0 -/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ -/* 1=bypass PLL*/ -#define CONFIG_PLL_BYPASS 0 -/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */ -/* Values can range from 1-64 */ +/* + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV + */ +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 25000000 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ #define CONFIG_VCO_MULT 20 -/* CONFIG_CCLK_DIV controls what the core clock divider is */ -/* Values can be 1, 2, 4, or 8 ONLY */ +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ #define CONFIG_CCLK_DIV 1 -/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/ -/* Values can range from 1-15 */ +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ #define CONFIG_SCLK_DIV 5 -/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ -/* Values can range from 2-65535 */ -/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ -#define CONFIG_SPI_BAUD 2 -#define CONFIG_SPI_BAUD_INITBLOCK 4 - -#if ( CONFIG_CLKIN_HALF == 0 ) -#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) -#else -#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) -#endif - -#if (CONFIG_PLL_BYPASS == 0) -#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) -#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) -#else -#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ -#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ -#endif - -#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */ -#define CONFIG_MEM_ADD_WDTH 10 /* 8, 9, 10, 11 */ -#define CONFIG_MEM_MT48LC32M8A2_75 1 -#define CONFIG_LOADS_ECHO 1 /* - * rarpb, bootp or dhcp commands will perform only a - * configuration lookup from the BOOTP/DHCP server - * but not try to load any image using TFTP + * Memory Settings */ -#define CONFIG_SYS_AUTOLOAD "no" +#define CONFIG_MEM_ADD_WDTH 10 +#define CONFIG_MEM_SIZE 64 + +#define CONFIG_EBIU_SDRRC_VAL 0x306 +#define CONFIG_EBIU_SDGCTL_VAL 0x91114d + +#define CONFIG_EBIU_AMGCTL_VAL 0xFF +#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 +#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 + +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) +#define CONFIG_SYS_MALLOC_LEN (384 * 1024) + /* * Network Settings */ -/* network support */ -#ifdef CONFIG_BFIN_MAC -#define CONFIG_IPADDR 192.168.0.15 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_GATEWAYIP 192.168.0.1 -#define CONFIG_SERVERIP 192.168.0.2 -#define CONFIG_HOSTNAME BF537 +#ifndef __ADSPBF534__ +#define ADI_CMDS_NETWORK 1 +#define CONFIG_BFIN_MAC +#define CONFIG_NETCONSOLE 1 +#define CONFIG_NET_MULTI 1 #endif - -#define CONFIG_ROOTPATH /romfs +#define CONFIG_HOSTNAME bf537-stamp /* Uncomment next line to use fixed MAC address */ /* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */ -/* This is the routine that copies the MAC in Flash to the 'ethaddr' setting */ - -#define CONFIG_SYS_LONGHELP 1 -#define CONFIG_BOOTDELAY 5 -#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */ -#define CONFIG_BOOTCOMMAND "run ramboot" - -#if defined(CONFIG_POST_TEST) -/* POST support */ -#define CONFIG_POST ( CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_UART | \ - CONFIG_SYS_POST_FLASH | \ - CONFIG_SYS_POST_ETHER | \ - CONFIG_SYS_POST_LED | \ - CONFIG_SYS_POST_BUTTON) -#else -#undef CONFIG_POST -#endif -#ifdef CONFIG_POST -#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */ -#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */ -#endif - -/* CF-CARD IDE-HDD Support */ - -/* #define CONFIG_BFIN_TRUE_IDE */ /* Add CF flash card support */ -/* #define CONFIG_BFIN_CF_IDE */ /* Add CF flash card support */ -/* #define CONFIG_BFIN_HDD_IDE */ /* Add IDE Disk Drive (HDD) support */ - -#if defined(CONFIG_BFIN_CF_IDE) || defined(CONFIG_BFIN_HDD_IDE) || defined(CONFIG_BFIN_TRUE_IDE) -# define CONFIG_BFIN_IDE 1 -#endif - -/*#define CONFIG_BF537_NAND */ /* Add nand flash support */ - -#define CONFIG_NETCONSOLE 1 -#define CONFIG_NET_MULTI 1 /* - * BOOTP options + * Flash Settings */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_BASE 0x20000000 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_PROTECTION +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +/* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */ +#define CONFIG_SYS_MAX_FLASH_SECT 71 /* - * Command line configuration. + * SPI Settings */ -#include +#define CONFIG_BFIN_SPI +#define CONFIG_ENV_SPI_MAX_HZ 30000000 +#define CONFIG_SF_DEFAULT_HZ 30000000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_ATMEL +#define CONFIG_SPI_FLASH_SPANSION +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SPI_FLASH_WINBOND -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_DATE -#ifndef CONFIG_BFIN_MAC -#undef CONFIG_CMD_NET +/* + * Env Storage Settings + */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 #else -#define CONFIG_CMD_PING -#endif - -#if defined(CONFIG_BFIN_CF_IDE) \ - || defined(CONFIG_BFIN_HDD_IDE) \ - || defined(CONFIG_BFIN_TRUE_IDE) -#define CONFIG_CMD_IDE -#endif - -#define CONFIG_CMD_DHCP - -#if defined(CONFIG_POST) -#define CONFIG_CMD_DIAG -#endif - -#ifdef CONFIG_BF537_NAND -#define CONFIG_CMD_NAND +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 #endif - - -#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600" -#define CONFIG_LOADADDR 0x1000000 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath) console=ttyBF0,57600\0"\ - "addip=setenv bootargs $(bootargs) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ - ":$(hostname):eth0:off\0" \ - "ramboot=tftpboot $(loadaddr) linux;" \ - "run ramargs;run addip;bootelf\0" \ - "nfsboot=tftpboot $(loadaddr) linux;" \ - "run nfsargs;run addip;bootelf\0" \ - "flashboot=bootm 0x20100000\0" \ - "update=tftpboot $(loadaddr) u-boot.bin;" \ - "protect off 0x20000000 0x2007FFFF;" \ - "erase 0x20000000 0x2007FFFF;cp.b 0x1000000 0x20000000 $(filesize)\0" \ - "" - -#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) +#define ENV_IS_EMBEDDED #else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define ENV_IS_EMBEDDED_CUSTOM #endif -#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024*1024) -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_MEMTEST_START 0x0 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024*1024) /* 1 ... 63 MB in DRAM */ -#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR /* default load address */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#define CONFIG_SYS_FLASH_BASE 0x20000000 -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CONFIG_SYS_FLASH_PROTECTION -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 71 /* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */ -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN) -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) -#define CONFIG_SYS_GBL_DATA_SIZE 0x4000 -#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4) -#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) -#define CONFIG_ENV_IS_IN_EEPROM 1 -#define CONFIG_ENV_OFFSET 0x4000 -#define CONFIG_ENV_HEADER (CONFIG_ENV_OFFSET + 0x16e) /* 0x12A is the length of LDR file header */ -#else -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0x20004000 -#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) -#endif -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */ -#define ENV_IS_EMBEDDED - -/* JFFS Partition offset set */ -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 -/* 512k reserved for u-boot */ -#define CONFIG_SYS_JFFS2_FIRST_SECTOR 15 +/* + * I2C Settings + */ +#define CONFIG_BFIN_TWI_I2C 1 +#define CONFIG_HARD_I2C 1 +#define CONFIG_SYS_I2C_SPEED 50000 +#define CONFIG_SYS_I2C_SLAVE 0 -#define CONFIG_SPI /* - * Stack sizes + * SPI_MMC Settings */ -#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#define CONFIG_MMC +#define CONFIG_BFIN_SPI_MMC -#define POLL_MODE 1 -#define FLASH_TOT_SECT 71 -#define FLASH_SIZE 0x400000 -#define CONFIG_SYS_FLASH_SIZE 0x400000 /* - * Board NAND Infomation + * NAND Settings */ +/* #define CONFIG_BF537_NAND */ +#ifdef CONFIG_BF537_NAND +# define CONFIG_CMD_NAND +#endif #define CONFIG_SYS_NAND_ADDR 0x20212000 #define CONFIG_SYS_NAND_BASE CONFIG_SYS_NAND_ADDR @@ -280,56 +152,35 @@ #define NAND_MAX_FLOORS 1 #define BFIN_NAND_READY PF3 -#define NAND_WAIT_READY(nand) \ - do { \ - int timeout = 0; \ - while(!(*pPORTFIO & PF3)) \ - if (timeout++ > 100000) \ - break; \ +#define NAND_WAIT_READY(nand) \ + do { \ + int timeout = 0; \ + while (!(*pPORTFIO & PF3)) \ + if (timeout++ > 100000) \ + break; \ } while (0) -#define BFIN_NAND_CLE (1<<2) /* A2 -> Command Enable */ -#define BFIN_NAND_ALE (1<<1) /* A1 -> Address Enable */ - -#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_CLE) = (__u8)(d); } while(0) -#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_ALE) = (__u8)(d); } while(0) -#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0) -#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr)) - -/* - * Initialize PSD4256 registers for using I2C - */ -#define CONFIG_MISC_INIT_R +#define BFIN_NAND_CLE (1 << 2) /* A2 -> Command Enable */ +#define BFIN_NAND_ALE (1 << 1) /* A1 -> Address Enable */ +#define WRITE_NAND_COMMAND(d, adr) bfin_write8(adr | BFIN_NAND_CLE, d) +#define WRITE_NAND_ADDRESS(d, adr) bfin_write8(adr | BFIN_NAND_ALE, d) +#define WRITE_NAND(d, adr) bfin_write8(adr, d) +#define READ_NAND(adr) bfin_read8(adr) -#define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */ /* - * I2C settings + * CF-CARD IDE-HDD Support */ -#define CONFIG_HARD_I2C 1 -#define CONFIG_BFIN_TWI_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 - -#define CONFIG_EBIU_SDRRC_VAL 0x306 -#define CONFIG_EBIU_SDGCTL_VAL 0x91114d -#define CONFIG_EBIU_SDBCTL_VAL 0x25 - -#define CONFIG_EBIU_AMGCTL_VAL 0xFF -#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 -#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 - -/* 0xFF, 0x7BB07BB0, 0x22547BB0 */ -/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN) -#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \ - ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN) -#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \ - B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN) -*/ +/* #define CONFIG_BFIN_TRUE_IDE */ /* Add CF flash card support */ +/* #define CONFIG_BFIN_CF_IDE */ /* Add CF flash card support */ +/* #define CONFIG_BFIN_HDD_IDE */ /* Add IDE Disk Drive (HDD) support */ -#define AMGCTLVAL 0xFF -#define AMBCTL0VAL 0x7BB07BB0 -#define AMBCTL1VAL 0xFFC27BB0 +#if defined(CONFIG_BFIN_CF_IDE) || \ + defined(CONFIG_BFIN_HDD_IDE) || \ + defined(CONFIG_BFIN_TRUE_IDE) +# define CONFIG_BFIN_IDE 1 +# define CONFIG_CMD_IDE +#endif #if defined(CONFIG_BFIN_IDE) @@ -341,11 +192,11 @@ #undef CONFIG_IDE_LED /* no led for ide supported */ #undef CONFIG_IDE_RESET /* no reset for ide supported */ -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ -#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1) -#undef AMBCTL1VAL -#define AMBCTL1VAL 0xFFC3FFC3 +#undef CONFIG_EBIU_AMBCTL1_VAL +#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC3FFC3 #define CONFIG_CF_ATASEL_DIS 0x20311800 #define CONFIG_CF_ATASEL_ENA 0x20311802 @@ -357,34 +208,54 @@ */ #define CONFIG_SYS_ATA_BASE_ADDR 0x2031C000 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* Offset for alternate registers */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */ #define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.Ax */ -#endif /* CONFIG_BFIN_TRUE_IDE */ -#if defined(CONFIG_BFIN_CF_IDE) /* USE CompactFlash Storage Card in the common memory space */ +#elif defined(CONFIG_BFIN_CF_IDE) #define CONFIG_SYS_ATA_BASE_ADDR 0x20211800 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x000E /* Offset for alternate registers */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x000E /* alternate registers */ #define CONFIG_SYS_ATA_STRIDE 1 /* CF.A0 --> Blackfin.Ax */ -#endif /* CONFIG_BFIN_CF_IDE */ -#if defined(CONFIG_BFIN_HDD_IDE) /* USE TRUE IDE */ +#elif defined(CONFIG_BFIN_HDD_IDE) #define CONFIG_SYS_ATA_BASE_ADDR 0x20314000 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* Offset for alternate registers */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */ #define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A1 */ - #undef CONFIG_SCLK_DIV #define CONFIG_SCLK_DIV 8 -#endif /* CONFIG_BFIN_HDD_IDE */ +#endif + +#endif -#endif /*CONFIG_BFIN_IDE */ + +/* + * Misc Settings + */ +#define CONFIG_MISC_INIT_R +#define CONFIG_RTC_BFIN +#define CONFIG_UART_CONSOLE 0 + +/* #define CONFIG_BF537_STAMP_LEDCMD 1 */ + +/* Define if want to do post memory test */ +#undef CONFIG_POST +#ifdef CONFIG_POST +#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */ +#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */ +#endif + + +/* + * Pull in common ADI header for remaining command/environment setup + */ +#include #include diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h index 320a8c69a6..ef2019f39d 100644 --- a/include/configs/bf561-ezkit.h +++ b/include/configs/bf561-ezkit.h @@ -2,229 +2,152 @@ * U-boot - Configuration file for BF561 EZKIT board */ -#ifndef __CONFIG_EZKIT561_H__ -#define __CONFIG_EZKIT561_H__ +#ifndef __CONFIG_BF561_EZKIT_H__ +#define __CONFIG_BF561_EZKIT_H__ #include -#define CONFIG_SYS_LONGHELP 1 -#define CONFIG_CMDLINE_EDITING 1 -#define CONFIG_BAUDRATE 57600 -/* Set default serial console for bf537 */ -#define CONFIG_UART_CONSOLE 0 -#define CONFIG_EZKIT561 1 -#define CONFIG_BOOTDELAY 5 - -#define CONFIG_PANIC_HANG 1 - -#define CONFIG_BFIN_CPU bf561-0.3 -#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS - -/* This sets the default state of the cache on U-Boot's boot */ -#define CONFIG_ICACHE_ON -#define CONFIG_DCACHE_ON /* - * Board settings + * Processor Settings */ -#define CONFIG_DRIVER_SMC91111 1 -#define CONFIG_SMC91111_BASE 0x2C010300 -#define CONFIG_ASYNC_EBIU_BASE CONFIG_SMC91111_BASE & ~(4*1024*1024) -#define CONFIG_SMC_USE_32_BIT 1 -#define CONFIG_MISC_INIT_R 1 - -/* - * Clock settings - */ - -/* CONFIG_CLKIN_HZ is any value in Hz */ -#define CONFIG_CLKIN_HZ 30000000 -/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ -/* 1=CLKIN/2 */ -#define CONFIG_CLKIN_HALF 0 -/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ -/* 1=bypass PLL */ -#define CONFIG_PLL_BYPASS 0 -/* CONFIG_VCO_MULT controls what the multiplier of the PLL is */ -/* Values can range from 1-64 */ -#define CONFIG_VCO_MULT 20 -/* CONFIG_CCLK_DIV controls what the core clock divider is */ -/* Values can be 1, 2, 4, or 8 ONLY */ -#define CONFIG_CCLK_DIV 1 -/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */ -/* Values can range from 1-15 */ -#define CONFIG_SCLK_DIV 5 -/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ -/* Values can range from 2-65535 */ -/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ -#define CONFIG_SPI_BAUD 2 -#define CONFIG_SPI_BAUD_INITBLOCK 4 +#define CONFIG_BFIN_CPU bf561-0.3 +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS -/* - * Network settings - */ -#if (CONFIG_DRIVER_SMC91111) -#define CONFIG_IPADDR 192.168.0.15 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_GATEWAYIP 192.168.0.1 -#define CONFIG_SERVERIP 192.168.0.2 -#define CONFIG_HOSTNAME ezkit561 -#define CONFIG_ROOTPATH /arm-cross-build/BF561/uClinux-dist/romfs -#endif /* CONFIG_DRIVER_SMC91111 */ /* - * Flash settings + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV */ +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 30000000 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 20 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 6 -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI_AMD_RESET -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_SYS_FLASH_BASE 0x20000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 135 /* max number of sectors on one chip */ -#define CONFIG_ENV_ADDR 0x20020000 -#define CONFIG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */ -/* JFFS Partition offset set */ -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 -/* 512k reserved for u-boot */ -#define CONFIG_SYS_JFFS2_FIRST_SECTOR 8 /* - * SDRAM settings & memory map + * Memory Settings */ +#define CONFIG_MEM_ADD_WDTH 9 +#define CONFIG_MEM_SIZE 64 -#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */ -#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */ -#define CONFIG_MEM_MT48LC16M16A2TG_75 1 - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024) - -#define CONFIG_SYS_MEMTEST_START 0x0 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024*1024) /* 1 ... 63 MB in DRAM */ +#define CONFIG_EBIU_SDRRC_VAL 0x306 +#define CONFIG_EBIU_SDGCTL_VAL 0x91114d -#define CONFIG_LOADADDR 0x01000000 /* default load address */ -#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN) +#define CONFIG_EBIU_AMGCTL_VAL 0x3F +#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 +#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) -#define CONFIG_SYS_GBL_DATA_SIZE 0x4000 -#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4) -#define CONFIG_STACKSIZE (128*1024) /* regular stack */ - -#if ( CONFIG_CLKIN_HALF == 0 ) -#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) -#else -#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) -#endif - -#if (CONFIG_PLL_BYPASS == 0) -#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) -#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) -#else -#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ -#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ -#endif /* - * Command settings + * Network Settings */ +#define ADI_CMDS_NETWORK 1 +#define CONFIG_DRIVER_SMC91111 1 +#define CONFIG_SMC91111_BASE 0x2C010300 +#define CONFIG_SMC_USE_32_BIT 1 +#define CONFIG_HOSTNAME bf561-ezkit +/* Uncomment next line to use fixed MAC address */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */ -#define CONFIG_SYS_AUTOLOAD "no" /* rarpb, bootp, dhcp commands will */ - /* only perform a configuration */ - /* lookup from the BOOTP/DHCP server */ - /* but not try to load any image */ - /* using TFTP */ -#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, */ - /* currently its disabled */ -#define CONFIG_BOOTCOMMAND "run ramboot" -#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600" - -#if (CONFIG_DRIVER_SMC91111) -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \ - "$(rootpath) console=ttyBF0,57600\0" \ - "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ - "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \ - "ramboot=tftpboot $(loadaddr) linux; " \ - "run ramargs; run addip; bootelf\0" \ - "nfsboot=tftpboot $(loadaddr) linux; " \ - "run nfsargs; run addip; bootelf\0" \ - "update=tftpboot $(loadaddr) u-boot.bin; " \ - "protect off 0x20000000 0x2003FFFF; " \ - "erase 0x20000000 0x2003FFFF; " \ - "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \ - "" -#else -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ - "flashboot=bootm 0x20100000\0" \ - "" -#endif - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME /* - * Command line configuration. + * Flash Settings */ -#include - -#define CONFIG_CMD_ELF -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_JFFS2 - -#if defined(CONFIG_DRIVER_SMC91111) -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI_AMD_RESET +#define CONFIG_SYS_FLASH_BASE 0x20000000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 135 +/* The BF561-EZKIT uses a top boot flash */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR 0x20004000 +#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) +#define ENV_IS_EMBEDDED +#else +#define ENV_IS_EMBEDDED_CUSTOM #endif + /* - * Console settings + * I2C Settings */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SOFT_I2C +#ifdef CONFIG_SOFT_I2C +#define PF_SCL PF0 +#define PF_SDA PF1 +#define I2C_INIT \ + do { \ + *pFIO0_DIR |= PF_SCL; \ + SSYNC(); \ + } while (0) +#define I2C_ACTIVE \ + do { \ + *pFIO0_DIR |= PF_SDA; \ + *pFIO0_INEN &= ~PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_TRISTATE \ + do { \ + *pFIO0_DIR &= ~PF_SDA; \ + *pFIO0_INEN |= PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_READ ((*pFIO0_FLAG_D & PF_SDA) != 0) +#define I2C_SDA(bit) \ + do { \ + if (bit) \ + *pFIO0_FLAG_S = PF_SDA; \ + else \ + *pFIO0_FLAG_C = PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_SCL(bit) \ + do { \ + if (bit) \ + *pFIO0_FLAG_S = PF_SCL; \ + else \ + *pFIO0_FLAG_C = PF_SCL; \ + SSYNC(); \ + } while (0) +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#define CONFIG_SYS_I2C_SPEED 50000 +#define CONFIG_SYS_I2C_SLAVE 0 #endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_LOADS_ECHO 1 /* - * Miscellaneous configurable options + * Misc Settings */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */ -#define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */ +#define CONFIG_UART_CONSOLE 0 + /* - * FLASH organization and environment definitions + * Pull in common ADI header for remaining command/environment setup */ -#define CONFIG_EBIU_SDRRC_VAL 0x306 -#define CONFIG_EBIU_SDGCTL_VAL 0x91114d -#define CONFIG_EBIU_SDBCTL_VAL 0x15 - -#define CONFIG_EBIU_AMGCTL_VAL 0x3F -#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 -#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 +#include #include diff --git a/include/configs/bfin_adi_common.h b/include/configs/bfin_adi_common.h new file mode 100644 index 0000000000..6afce4da9d --- /dev/null +++ b/include/configs/bfin_adi_common.h @@ -0,0 +1,198 @@ +/* + * U-Boot - Common settings for Analog Devices boards + */ + +#ifndef __CONFIG_BFIN_ADI_COMMON_H__ +#define __CONFIG_BFIN_ADI_COMMON_H__ + +/* + * Command Settings + */ +#ifndef _CONFIG_CMD_DEFAULT_H +# include +# if ADI_CMDS_NETWORK +# define CONFIG_CMD_DHCP +# define CONFIG_CMD_PING +# ifdef CONFIG_BFIN_MAC +# define CONFIG_CMD_MII +# endif +# else +# undef CONFIG_CMD_BOOTD +# undef CONFIG_CMD_NET +# undef CONFIG_CMD_NFS +# endif +# ifdef CONFIG_LIBATA +# define CONFIG_CMD_FAT +# define CONFIG_CMD_SATA +# define CONFIG_DOS_PARTITION +# endif +# ifdef CONFIG_MMC +# define CONFIG_CMD_FAT +# define CONFIG_CMD_MMC +# define CONFIG_DOS_PARTITION +# endif +# ifdef CONFIG_USB +# define CONFIG_CMD_EXT2 +# define CONFIG_CMD_FAT +# define CONFIG_CMD_USB +# define CONFIG_CMD_USB_STORAGE +# define CONFIG_DOS_PARTITION +# endif +# ifdef CONFIG_POST +# define CONFIG_CMD_DIAG +# endif +# ifdef CONFIG_RTC_BFIN +# define CONFIG_CMD_DATE +# endif +# ifdef CONFIG_SPI +# define CONFIG_CMD_EEPROM +# endif +# if defined(CONFIG_BFIN_SPI) || defined(CONFIG_SOFT_SPI) +# define CONFIG_CMD_SPI +# endif +# ifdef CONFIG_SPI_FLASH +# define CONFIG_CMD_SF +# endif +# if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +# define CONFIG_CMD_I2C +# endif +# ifdef CONFIG_SYS_NO_FLASH +# undef CONFIG_CMD_FLASH +# undef CONFIG_CMD_IMLS +# else +# define CONFIG_CMD_JFFS2 +# endif +# define CONFIG_CMD_BOOTLDR +# define CONFIG_CMD_CACHE +# define CONFIG_CMD_CPLBINFO +# define CONFIG_CMD_ELF +# define CONFIG_ELF_SIMPLE_LOAD +# define CONFIG_CMD_REGINFO +# define CONFIG_CMD_STRINGS +# if defined(__ADSPBF51x__) || defined(__ADSPBF52x__) || defined(__ADSPBF54x__) +# define CONFIG_CMD_OTP +# endif +#endif + +/* + * Console Settings + */ +#define CONFIG_SYS_LONGHELP 1 +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_AUTO_COMPLETE 1 +#define CONFIG_LOADS_ECHO 1 +#define CONFIG_JTAG_CONSOLE +#ifndef CONFIG_BAUDRATE +# define CONFIG_BAUDRATE 57600 +#endif + +/* + * Debug Settings + */ +#define CONFIG_ENV_OVERWRITE 1 +#define CONFIG_DEBUG_DUMP 1 +#define CONFIG_DEBUG_DUMP_SYMS 1 +#define CONFIG_PANIC_HANG 1 + +/* + * Env Settings + */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) +# define CONFIG_BOOTDELAY -1 +#else +# define CONFIG_BOOTDELAY 5 +#endif +#define CONFIG_BOOTCOMMAND "run ramboot" +#ifdef CONFIG_VIDEO +# define CONFIG_BOOTARGS_VIDEO "console=tty0 " +#else +# define CONFIG_BOOTARGS_VIDEO "" +#endif +#define CONFIG_BOOTARGS \ + "root=/dev/mtdblock0 rw " \ + "earlyprintk=" \ + "serial," \ + "uart" MK_STR(CONFIG_UART_CONSOLE) "," \ + MK_STR(CONFIG_BAUDRATE) " " \ + CONFIG_BOOTARGS_VIDEO \ + "console=ttyBF0," MK_STR(CONFIG_BAUDRATE) + +#if defined(CONFIG_CMD_NET) +# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) +# define UBOOT_ENV_FILE "u-boot.bin" +# else +# define UBOOT_ENV_FILE "u-boot.ldr" +# endif +# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) +# ifdef CONFIG_SPI +# define UBOOT_ENV_UPDATE \ + "eeprom write $(loadaddr) 0x0 $(filesize)" +# else +# define UBOOT_ENV_UPDATE \ + "sf probe " MK_STR(BFIN_BOOT_SPI_SSEL) ";" \ + "sf erase 0 0x40000;" \ + "sf write $(loadaddr) 0 $(filesize)" +# endif +# elif (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND) +# define UBOOT_ENV_UPDATE \ + "nand unlock 0 0x40000;" \ + "nand erase 0 0x40000;" \ + "nand write $(loadaddr) 0 0x40000" +# else +# define UBOOT_ENV_UPDATE \ + "protect off 0x20000000 0x2003FFFF;" \ + "erase 0x20000000 0x2003FFFF;" \ + "cp.b $(loadaddr) 0x20000000 $(filesize)" +# endif +# define NETWORK_ENV_SETTINGS \ + "ubootfile=" UBOOT_ENV_FILE "\0" \ + "update=" \ + "tftp $(loadaddr) $(ubootfile);" \ + UBOOT_ENV_UPDATE \ + "\0" \ + "addip=set bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):" \ + "$(hostname):eth0:off" \ + "\0" \ + "ramargs=set bootargs " CONFIG_BOOTARGS "\0" \ + "ramboot=" \ + "tftp $(loadaddr) uImage;" \ + "run ramargs;" \ + "run addip;" \ + "bootm" \ + "\0" \ + "nfsargs=set bootargs " \ + "root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath),tcp,nfsvers=3" \ + "\0" \ + "nfsboot=" \ + "tftp $(loadaddr) vmImage;" \ + "run nfsargs;" \ + "run addip;" \ + "bootm" \ + "\0" +#else +# define NETWORK_ENV_SETTINGS +#endif +#define CONFIG_EXTRA_ENV_SETTINGS \ + NETWORK_ENV_SETTINGS \ + "flashboot=bootm 0x20100000\0" + +/* + * Network Settings + */ +#ifdef CONFIG_CMD_NET +# define CONFIG_IPADDR 192.168.0.15 +# define CONFIG_NETMASK 255.255.255.0 +# define CONFIG_GATEWAYIP 192.168.0.1 +# define CONFIG_SERVERIP 192.168.0.2 +# define CONFIG_ROOTPATH /romfs +# ifdef CONFIG_CMD_DHCP +# ifndef CONFIG_SYS_AUTOLOAD +# define CONFIG_SYS_AUTOLOAD "no" +# endif +# endif +# define CONFIG_NET_RETRY_COUNT 20 +#endif + +#endif -- cgit v1.2.1 From 23fd959eeaaa0434ac7f9c1191de66c76d97d699 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Sat, 11 Oct 2008 22:40:22 -0400 Subject: Blackfin: bf533-stamp: rewrite startup LED notifications Again, don't clobber pins that we aren't actually using, and use the common LED framework rather than our own hob-job-but-not-really-working. Signed-off-by: Mike Frysinger --- include/configs/bf533-stamp.h | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+) (limited to 'include/configs') diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h index 622f54c38c..c6fd0384da 100644 --- a/include/configs/bf533-stamp.h +++ b/include/configs/bf533-stamp.h @@ -207,6 +207,31 @@ /* FLASH/ETHERNET uses the same async bank */ #define SHARED_RESOURCES 1 +/* define to enable boot progress via leds */ +/* #define CONFIG_SHOW_BOOT_PROGRESS */ + +/* define to enable run status via led */ +/* #define CONFIG_STATUS_LED */ +#ifdef CONFIG_STATUS_LED +#define CONFIG_BOARD_SPECIFIC_LED +#ifndef __ASSEMBLY__ +typedef unsigned int led_id_t; +void __led_init(led_id_t mask, int state); +void __led_set(led_id_t mask, int state); +void __led_toggle(led_id_t mask); +#endif +/* use LED1 to indicate booting/alive */ +#define STATUS_LED_BOOT 0 +#define STATUS_LED_BIT 1 +#define STATUS_LED_STATE STATUS_LED_ON +#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4) +/* use LED2 to indicate crash */ +#define STATUS_LED_CRASH 1 +#define STATUS_LED_BIT1 2 +#define STATUS_LED_STATE1 STATUS_LED_ON +#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) +#endif + /* define to enable splash screen support */ /* #define CONFIG_VIDEO */ -- cgit v1.2.1 From 9f64ba2412d3cede9eb1f290987e5c3a28df3232 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Sun, 12 Oct 2008 23:49:13 -0400 Subject: Blackfin: bf533-stamp: bump up default clocks Since the hardware can handle it, bump the default clocks from 80mhz SCLK and 398mhz CCLK to 100mhz SCLK and 498mhz CCLK. Signed-off-by: Mike Frysinger --- include/configs/bf533-stamp.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/configs') diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h index c6fd0384da..d8e1ffc1d5 100644 --- a/include/configs/bf533-stamp.h +++ b/include/configs/bf533-stamp.h @@ -30,7 +30,7 @@ #define CONFIG_PLL_BYPASS 0 /* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ /* Values can range from 0-63 (where 0 means 64) */ -#define CONFIG_VCO_MULT 36 +#define CONFIG_VCO_MULT 45 /* CCLK_DIV controls the core clock divider */ /* Values can be 1, 2, 4, or 8 ONLY */ #define CONFIG_CCLK_DIV 1 -- cgit v1.2.1 From 88f9faffb383bbc6f23b8cc8519c5ffecfa2c8ad Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Tue, 9 Dec 2008 13:47:39 -0500 Subject: Blackfin: add clkin_hz= to default kernel command line for ADI boards Signed-off-by: Mike Frysinger --- include/configs/bfin_adi_common.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/configs') diff --git a/include/configs/bfin_adi_common.h b/include/configs/bfin_adi_common.h index 6afce4da9d..bfe53762c3 100644 --- a/include/configs/bfin_adi_common.h +++ b/include/configs/bfin_adi_common.h @@ -110,6 +110,7 @@ #endif #define CONFIG_BOOTARGS \ "root=/dev/mtdblock0 rw " \ + "clkin_hz=" MK_STR(CONFIG_CLKIN_HZ) " " \ "earlyprintk=" \ "serial," \ "uart" MK_STR(CONFIG_UART_CONSOLE) "," \ -- cgit v1.2.1 From f82caaccc87e1f76448ff42a6b930e59797e4f65 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Mon, 8 Dec 2008 16:16:11 -0500 Subject: Blackfin: bf537-stamp: bump default SCLK up to 125MHz Since all of the bf537-stamp and bf537-ezkit boards out there can handle it, increase the speed of SCLK to 125MHz rather than 100MHz. Signed-off-by: Mike Frysinger --- include/configs/bf537-stamp.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/configs') diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h index 7c35a022f9..a9cdd5cef3 100644 --- a/include/configs/bf537-stamp.h +++ b/include/configs/bf537-stamp.h @@ -36,7 +36,7 @@ #define CONFIG_CCLK_DIV 1 /* SCLK_DIV controls the system clock divider */ /* Values can range from 1-15 */ -#define CONFIG_SCLK_DIV 5 +#define CONFIG_SCLK_DIV 4 /* -- cgit v1.2.1 From 6f5fd56f0832ea5c254e2e4be84ea21fc8ecd5c5 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 21 Jan 2009 20:47:12 -0500 Subject: Blackfin: bf537-stamp: increase monitor size The new jffs2 code pushed the code size just over the limit, so increase the limit a bit more. Signed-off-by: Mike Frysinger --- include/configs/bf537-stamp.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/configs') diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h index a9cdd5cef3..3e5862d138 100644 --- a/include/configs/bf537-stamp.h +++ b/include/configs/bf537-stamp.h @@ -52,7 +52,7 @@ #define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 #define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 -#define CONFIG_SYS_MONITOR_LEN (384 * 1024) +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) #define CONFIG_SYS_MALLOC_LEN (384 * 1024) -- cgit v1.2.1