From e97f7fbba5901ff4daa0e2e7f0cdbb5a98131d09 Mon Sep 17 00:00:00 2001 From: Bin Meng Date: Mon, 16 Nov 2015 01:19:16 -0800 Subject: net: e1000: Remove dead codes wrapped by #if 0 Remove those dead codes wrapped by #if 0 and #endif. Signed-off-by: Bin Meng Acked-by: Joe Hershberger --- drivers/net/e1000.c | 75 +---------------------------------------------------- 1 file changed, 1 insertion(+), 74 deletions(-) (limited to 'drivers/net/e1000.c') diff --git a/drivers/net/e1000.c b/drivers/net/e1000.c index 2ba03ed73e..508ebfb55b 100644 --- a/drivers/net/e1000.c +++ b/drivers/net/e1000.c @@ -551,43 +551,6 @@ static int32_t e1000_init_eeprom_params(struct e1000_hw *hw) eeprom->use_eerd = true; eeprom->use_eewr = false; break; - - /* ich8lan does not support currently. if needed, please - * add corresponding code and functions. - */ -#if 0 - case e1000_ich8lan: - { - int32_t i = 0; - - eeprom->type = e1000_eeprom_ich8; - eeprom->use_eerd = false; - eeprom->use_eewr = false; - eeprom->word_size = E1000_SHADOW_RAM_WORDS; - uint32_t flash_size = E1000_READ_ICH_FLASH_REG(hw, - ICH_FLASH_GFPREG); - /* Zero the shadow RAM structure. But don't load it from NVM - * so as to save time for driver init */ - if (hw->eeprom_shadow_ram != NULL) { - for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { - hw->eeprom_shadow_ram[i].modified = false; - hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF; - } - } - - hw->flash_base_addr = (flash_size & ICH_GFPREG_BASE_MASK) * - ICH_FLASH_SECTOR_SIZE; - - hw->flash_bank_size = ((flash_size >> 16) - & ICH_GFPREG_BASE_MASK) + 1; - hw->flash_bank_size -= (flash_size & ICH_GFPREG_BASE_MASK); - - hw->flash_bank_size *= ICH_FLASH_SECTOR_SIZE; - - hw->flash_bank_size /= 2 * sizeof(uint16_t); - break; - } -#endif default: break; } @@ -838,14 +801,6 @@ e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset, if (eeprom->use_eerd == true) return e1000_read_eeprom_eerd(hw, offset, words, data); - /* ich8lan does not support currently. if needed, please - * add corresponding code and functions. - */ -#if 0 - /* ICH EEPROM access is done via the ICH flash controller */ - if (eeprom->type == e1000_eeprom_ich8) - return e1000_read_eeprom_ich8(hw, offset, words, data); -#endif /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have * acquired the EEPROM at this point, so any returns should relase it */ if (eeprom->type == e1000_eeprom_spi) { @@ -1732,17 +1687,7 @@ e1000_init_hw(struct e1000_hw *hw, unsigned char enetaddr[6]) * occuring when accessing our register space */ E1000_WRITE_FLUSH(hw); } -#if 0 - /* Set the PCI priority bit correctly in the CTRL register. This - * determines if the adapter gives priority to receives, or if it - * gives equal priority to transmits and receives. Valid only on - * 82542 and 82543 silicon. - */ - if (hw->dma_fairness && hw->mac_type <= e1000_82543) { - ctrl = E1000_READ_REG(hw, CTRL); - E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PRIOR); - } -#endif + switch (hw->mac_type) { case e1000_82545_rev_3: case e1000_82546_rev_3: @@ -1842,20 +1787,6 @@ e1000_init_hw(struct e1000_hw *hw, unsigned char enetaddr[6]) break; } -#if 0 - /* Clear all of the statistics registers (clear on read). It is - * important that we do this after we have tried to establish link - * because the symbol error count will increment wildly if there - * is no link. - */ - e1000_clear_hw_cntrs(hw); - - /* ICH8 No-snoop bits are opposite polarity. - * Set to snoop by default after reset. */ - if (hw->mac_type == e1000_ich8lan) - e1000_set_pci_ex_no_snoop(hw, PCI_EX_82566_SNOOP_ALL); -#endif - if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER || hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) { ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); @@ -5230,10 +5161,6 @@ _e1000_disable(struct e1000_hw *hw) E1000_WRITE_REG(hw, RDH, 0); E1000_WRITE_REG(hw, RDT, 0); - /* put the card in its initial state */ -#if 0 - E1000_WRITE_REG(hw, CTRL, E1000_CTRL_RST); -#endif mdelay(10); } -- cgit v1.2.1