From 54b99e51ab580eb6373f93994fe8f8a8edeefcf8 Mon Sep 17 00:00:00 2001
From: Eric Nelson <eric.nelson@boundarydevices.com>
Date: Sun, 23 Sep 2012 10:12:56 +0000
Subject: i2c_probe: update for use in scripting

Allow the use of an I2C address to test and return success
if one or more devices is found.

This allows device presence to alter the flow of a script.
e.g.
   if i2c probe 0x04 ; then
	echo found Hannstar touch ;
   fi

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
---
 common/cmd_i2c.c | 20 ++++++++++++++++----
 1 file changed, 16 insertions(+), 4 deletions(-)

(limited to 'common')

diff --git a/common/cmd_i2c.c b/common/cmd_i2c.c
index b59470e7f6..82e63e1322 100644
--- a/common/cmd_i2c.c
+++ b/common/cmd_i2c.c
@@ -605,18 +605,28 @@ mod_i2c_mem(cmd_tbl_t *cmdtp, int incrflag, int flag, int argc, char * const arg
 
 /*
  * Syntax:
- *	i2c probe {addr}{.0, .1, .2}
+ *	i2c probe {addr}
+ *
+ * Returns zero (success) if one or more I2C devices was found
  */
 static int do_i2c_probe (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 {
 	int j;
+	int addr = -1;
+	int found = 0;
 #if defined(CONFIG_SYS_I2C_NOPROBES)
 	int k, skip;
 	uchar bus = GET_BUS_NUM;
 #endif	/* NOPROBES */
 
+	if (argc == 2)
+		addr = simple_strtol(argv[1], 0, 16);
+
 	puts ("Valid chip addresses:");
 	for (j = 0; j < 128; j++) {
+		if ((0 <= addr) && (j != addr))
+			continue;
+
 #if defined(CONFIG_SYS_I2C_NOPROBES)
 		skip = 0;
 		for (k=0; k < NUM_ELEMENTS_NOPROBE; k++) {
@@ -628,8 +638,10 @@ static int do_i2c_probe (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv
 		if (skip)
 			continue;
 #endif
-		if (i2c_probe(j) == 0)
+		if (i2c_probe(j) == 0) {
 			printf(" %02X", j);
+			found++;
+		}
 	}
 	putc ('\n');
 
@@ -642,7 +654,7 @@ static int do_i2c_probe (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv
 	putc ('\n');
 #endif
 
-	return 0;
+	return (0 == found);
 }
 
 /*
@@ -1380,7 +1392,7 @@ U_BOOT_CMD(
 	"i2c mm chip address[.0, .1, .2] - write to I2C device (auto-incrementing)\n"
 	"i2c mw chip address[.0, .1, .2] value [count] - write to I2C device (fill)\n"
 	"i2c nm chip address[.0, .1, .2] - write to I2C device (constant address)\n"
-	"i2c probe - show devices on the I2C bus\n"
+	"i2c probe [address] - test for and show device(s) on the I2C bus\n"
 	"i2c read chip address[.0, .1, .2] length memaddress - read to memory \n"
 	"i2c write memaddress chip address[.0, .1, .2] length - write memory to i2c\n"
 	"i2c reset - re-init the I2C Controller\n"
-- 
cgit v1.2.1