From 932394ac43e2e778e664eeb6e456fecd0fae6e59 Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Wed, 17 Aug 2005 12:55:25 +0200 Subject: Rewrite of NAND code based on what is in 2.6.12 Linux kernel Patch by Ladislav Michl, 29 Jun 2005 --- common/cmd_nand.c | 2039 ++++++++--------------------------------------------- 1 file changed, 277 insertions(+), 1762 deletions(-) (limited to 'common') diff --git a/common/cmd_nand.c b/common/cmd_nand.c index 449991785c..ae4c68ac1f 100644 --- a/common/cmd_nand.c +++ b/common/cmd_nand.c @@ -1,18 +1,15 @@ /* - * Driver for NAND support, Rick Bronson - * borrowed heavily from: - * (c) 1999 Machine Vision Holdings, Inc. - * (c) 1999, 2000 David Woodhouse - * - * Added 16-bit nand support - * (C) 2004 Texas Instruments + * Rick Bronson and Pantelis Antoniou */ #include + +#if (CONFIG_COMMANDS & CFG_CMD_NAND) + #include -#include -#include #include +#include +#include #ifdef CONFIG_SHOW_BOOT_PROGRESS # include @@ -21,289 +18,311 @@ # define SHOW_BOOT_PROGRESS(arg) #endif -#if (CONFIG_COMMANDS & CFG_CMD_NAND) - -#include -#include #include +#include -#ifdef CONFIG_OMAP1510 -void archflashwp(void *archdata, int wp); -#endif +extern nand_info_t nand_info[]; /* info for NAND chips */ -#define ROUND_DOWN(value,boundary) ((value) & (~((boundary)-1))) +static int nand_dump_oob(nand_info_t *nand, ulong off) +{ + return 0; +} -/* - * Definition of the out of band configuration structure - */ -struct nand_oob_config { - int ecc_pos[6]; /* position of ECC bytes inside oob */ - int badblock_pos; /* position of bad block flag inside oob -1 = inactive */ - int eccvalid_pos; /* position of ECC valid flag inside oob -1 = inactive */ -} oob_config = { {0}, 0, 0}; - -#undef NAND_DEBUG -#undef PSYCHO_DEBUG - -/* ****************** WARNING ********************* - * When ALLOW_ERASE_BAD_DEBUG is non-zero the erase command will - * erase (or at least attempt to erase) blocks that are marked - * bad. This can be very handy if you are _sure_ that the block - * is OK, say because you marked a good block bad to test bad - * block handling and you are done testing, or if you have - * accidentally marked blocks bad. - * - * Erasing factory marked bad blocks is a _bad_ idea. If the - * erase succeeds there is no reliable way to find them again, - * and attempting to program or erase bad blocks can affect - * the data in _other_ (good) blocks. - */ -#define ALLOW_ERASE_BAD_DEBUG 0 +static int nand_dump(nand_info_t *nand, ulong off) +{ + int i; + u_char *buf, *p; + + buf = malloc(nand->oobblock + nand->oobsize); + if (!buf) { + puts("No memory for page buffer\n"); + return 1; + } + off &= ~(nand->oobblock - 1); + i = nand_read_raw(nand, buf, off, nand->oobblock, nand->oobsize); + if (i < 0) { + printf("Error (%d) reading page %08x\n", i, off); + free(buf); + return 1; + } + printf("Page %08x dump:\n", off); + i = nand->oobblock >> 4; p = buf; + while (i--) { + printf( "\t%02x %02x %02x %02x %02x %02x %02x %02x" + " %02x %02x %02x %02x %02x %02x %02x %02x\n", + p[0], p[1], p[2], p[3], p[4], p[5], p[6], p[7], + p[8], p[9], p[10], p[11], p[12], p[13], p[14], p[15]); + p += 16; + } + puts("OOB:\n"); + i = nand->oobsize >> 3; + while (i--) { + printf( "\t%02x %02x %02x %02x %02x %02x %02x %02x\n", + p[0], p[1], p[2], p[3], p[4], p[5], p[6], p[7]); + p += 8; + } + free(buf); -#define CONFIG_MTD_NAND_ECC /* enable ECC */ -#define CONFIG_MTD_NAND_ECC_JFFS2 + return 0; +} -/* bits for nand_rw() `cmd'; or together as needed */ -#define NANDRW_READ 0x01 -#define NANDRW_WRITE 0x00 -#define NANDRW_JFFS2 0x02 -#define NANDRW_JFFS2_SKIP 0x04 +/* ------------------------------------------------------------------------- */ -/* - * Function Prototypes - */ -static void nand_print(struct nand_chip *nand); -int nand_rw (struct nand_chip* nand, int cmd, - size_t start, size_t len, - size_t * retlen, u_char * buf); -int nand_erase(struct nand_chip* nand, size_t ofs, size_t len, int clean); -static int nand_read_ecc(struct nand_chip *nand, size_t start, size_t len, - size_t * retlen, u_char *buf, u_char *ecc_code); -static int nand_write_ecc (struct nand_chip* nand, size_t to, size_t len, - size_t * retlen, const u_char * buf, u_char * ecc_code); -static void nand_print_bad(struct nand_chip *nand); -static int nand_read_oob(struct nand_chip* nand, size_t ofs, size_t len, - size_t * retlen, u_char * buf); -static int nand_write_oob(struct nand_chip* nand, size_t ofs, size_t len, - size_t * retlen, const u_char * buf); -static int NanD_WaitReady(struct nand_chip *nand, int ale_wait); -#ifdef CONFIG_MTD_NAND_ECC -static int nand_correct_data (u_char *dat, u_char *read_ecc, u_char *calc_ecc); -static void nand_calculate_ecc (const u_char *dat, u_char *ecc_code); +static void +arg_off_size(int argc, char *argv[], ulong *off, ulong *size, ulong totsize) +{ + *off = 0; + *size = 0; + +#if defined(CONFIG_JFFS2_NAND) && defined(CFG_JFFS_CUSTOM_PART) + if (argc >= 1 && strcmp(argv[0], "partition") == 0) { + int part_num; + struct part_info *part; + const char *partstr; + + if (argc >= 2) + partstr = argv[1]; + else + partstr = getenv("partition"); + + if (partstr) + part_num = (int)simple_strtoul(partstr, NULL, 10); + else + part_num = 0; + + part = jffs2_part_info(part_num); + if (part == NULL) { + printf("\nInvalid partition %d\n", part_num); + return; + } + *size = part->size; + *off = (ulong)part->offset; + } else #endif + { + if (argc >= 1) + *off = (ulong)simple_strtoul(argv[0], NULL, 16); + else + *off = 0; -struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE] = {{0}}; + if (argc >= 2) + *size = (ulong)simple_strtoul(argv[1], NULL, 16); + else + *size = totsize - *off; -/* Current NAND Device */ -static int curr_device = -1; + } -/* ------------------------------------------------------------------------- */ +} -int do_nand (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) { - int rcode = 0; + int i, dev, ret; + ulong addr, off, size; + char *cmd, *s; + nand_info_t *nand; - switch (argc) { - case 0: - case 1: - printf ("Usage:\n%s\n", cmdtp->usage); - return 1; - case 2: - if (strcmp(argv[1],"info") == 0) { - int i; + /* at least two arguments please */ + if (argc < 2) + goto usage; - putc ('\n'); + cmd = argv[1]; - for (i=0; i= CFG_MAX_NAND_DEVICE)) { - puts ("\nno devices available\n"); - return 1; + putc('\n'); + for (i = 0; i < CFG_MAX_NAND_DEVICE; i++) { + if (nand_info[i].name) + printf("Device %d: %s\n", i, nand_info[i].name); } - printf ("\nDevice %d: ", curr_device); - nand_print(&nand_dev_desc[curr_device]); return 0; + } - } else if (strcmp(argv[1],"bad") == 0) { - if ((curr_device < 0) || (curr_device >= CFG_MAX_NAND_DEVICE)) { - puts ("\nno devices available\n"); + if (strcmp(cmd, "device") == 0) { + + if (argc < 3) { + if ((nand_curr_device < 0) || + (nand_curr_device >= CFG_MAX_NAND_DEVICE)) + puts("\nno devices available\n"); + else + printf("\nDevice %d: %s\n", nand_curr_device, + nand_info[nand_curr_device].name); + return 0; + } + dev = (int)simple_strtoul(argv[2], NULL, 10); + if (dev < 0 || dev >= CFG_MAX_NAND_DEVICE || !nand_info[dev].name) { + puts("No such device\n"); return 1; } - printf ("\nDevice %d bad blocks:\n", curr_device); - nand_print_bad(&nand_dev_desc[curr_device]); + printf("Device %d: %s", dev, nand_info[dev].name); + puts("... is now current device\n"); + nand_curr_device = dev; return 0; + } + + if (strcmp(cmd, "bad") != 0 && strcmp(cmd, "erase") != 0 && + strncmp(cmd, "dump", 4) != 0 && + strncmp(cmd, "read", 4) != 0 && strncmp(cmd, "write", 5) != 0 +#ifdef CONFIG_MTD_NAND_UNSAFE + && strcmp(cmd, "scrub") != 0 && strcmp(cmd, "biterr") != 0 + && strcmp(cmd, "markbad") != 0 +#endif + ) + goto usage; + /* the following commands operate on the current device */ + if (nand_curr_device < 0 || nand_curr_device >= CFG_MAX_NAND_DEVICE || + !nand_info[nand_curr_device].name) { + puts("\nno devices available\n"); + return 1; } - printf ("Usage:\n%s\n", cmdtp->usage); - return 1; - case 3: - if (strcmp(argv[1],"device") == 0) { - int dev = (int)simple_strtoul(argv[2], NULL, 10); + nand = &nand_info[nand_curr_device]; - printf ("\nDevice %d: ", dev); - if (dev >= CFG_MAX_NAND_DEVICE) { - puts ("unknown device\n"); - return 1; - } - nand_print(&nand_dev_desc[dev]); - /*nand_print (dev);*/ + if (strcmp(cmd, "bad") == 0) { + printf("\nDevice %d bad blocks:\n", nand_curr_device); + for (off = 0; off < nand->size; off += nand->erasesize) + if (nand_block_isbad(nand, off)) + printf(" %08x\n", off); + return 0; + } + + if (strcmp(cmd, "erase") == 0 +#ifdef CONFIG_MTD_NAND_UNSAFE + || strcmp(cmd, "scrub") == 0 +#endif + ) { - if (nand_dev_desc[dev].ChipID == NAND_ChipID_UNKNOWN) { +#ifdef CONFIG_MTD_NAND_UNSAFE + i = strcmp(cmd, "scrub") == 0; /* 1 scrub, 0 = erase */ +#endif + + arg_off_size(argc - 2, argv + 2, &off, &size, nand->size); + if (off == 0 && size == 0) return 1; - } - curr_device = dev; + printf("\nNAND %s: device %d offset 0x%x, size 0x%x ", +#ifdef CONFIG_MTD_NAND_UNSAFE + i ? "scrub" : +#endif + "erase", + nand_curr_device, off, size); - puts ("... is now current device\n"); +#ifdef CONFIG_MTD_NAND_UNSAFE + if (i) + ret = nand_scrub(nand, off, size); + else +#endif + ret = nand_erase(nand, off, size); - return 0; + printf("%s\n", ret ? "ERROR" : "OK"); + + return ret == 0 ? 0 : 1; } - else if (strcmp(argv[1],"erase") == 0 && strcmp(argv[2], "clean") == 0) { - struct nand_chip* nand = &nand_dev_desc[curr_device]; - ulong off = 0; - ulong size = nand->totlen; - int ret; - printf ("\nNAND erase: device %d offset %ld, size %ld ... ", - curr_device, off, size); + if (strncmp(cmd, "dump", 4) == 0) { + if (argc < 3) + goto usage; - ret = nand_erase (nand, off, size, 1); + s = strchr(cmd, '.'); + off = (int)simple_strtoul(argv[2], NULL, 16); - printf("%s\n", ret ? "ERROR" : "OK"); + if (s != NULL && strcmp(s, ".oob") == 0) + ret = nand_dump_oob(nand, off); + else + ret = nand_dump(nand, off); + + return ret == 0 ? 1 : 0; - return ret; } - printf ("Usage:\n%s\n", cmdtp->usage); - return 1; - default: - /* at least 4 args */ - - if (strncmp(argv[1], "read", 4) == 0 || - strncmp(argv[1], "write", 5) == 0) { - ulong addr = simple_strtoul(argv[2], NULL, 16); - ulong off = simple_strtoul(argv[3], NULL, 16); - ulong size = simple_strtoul(argv[4], NULL, 16); - int cmd = (strncmp(argv[1], "read", 4) == 0) ? - NANDRW_READ : NANDRW_WRITE; - int ret, total; - char* cmdtail = strchr(argv[1], '.'); - - if (cmdtail && !strncmp(cmdtail, ".oob", 2)) { - /* read out-of-band data */ - if (cmd & NANDRW_READ) { - ret = nand_read_oob(nand_dev_desc + curr_device, - off, size, &total, - (u_char*)addr); - } - else { - ret = nand_write_oob(nand_dev_desc + curr_device, - off, size, &total, - (u_char*)addr); - } - return ret; - } - else if (cmdtail && !strncmp(cmdtail, ".jffs2", 2)) - cmd |= NANDRW_JFFS2; /* skip bad blocks */ - else if (cmdtail && !strncmp(cmdtail, ".jffs2s", 2)) { - cmd |= NANDRW_JFFS2; /* skip bad blocks (on read too) */ - if (cmd & NANDRW_READ) - cmd |= NANDRW_JFFS2_SKIP; /* skip bad blocks (on read too) */ - } -#ifdef SXNI855T - /* need ".e" same as ".j" for compatibility with older units */ - else if (cmdtail && !strcmp(cmdtail, ".e")) - cmd |= NANDRW_JFFS2; /* skip bad blocks */ -#endif -#ifdef CFG_NAND_SKIP_BAD_DOT_I - /* need ".i" same as ".jffs2s" for compatibility with older units (esd) */ - /* ".i" for image -> read skips bad block (no 0xff) */ - else if (cmdtail && !strcmp(cmdtail, ".i")) - cmd |= NANDRW_JFFS2; /* skip bad blocks (on read too) */ - if (cmd & NANDRW_READ) - cmd |= NANDRW_JFFS2_SKIP; /* skip bad blocks (on read too) */ -#endif /* CFG_NAND_SKIP_BAD_DOT_I */ - else if (cmdtail) { - printf ("Usage:\n%s\n", cmdtp->usage); + /* read write */ + if (strncmp(cmd, "read", 4) == 0 || strncmp(cmd, "write", 5) == 0) { + if (argc < 4) + goto usage; +/* + s = strchr(cmd, '.'); + clean = CLEAN_NONE; + if (s != NULL) { + if (strcmp(s, ".jffs2") == 0 || strcmp(s, ".e") == 0 + || strcmp(s, ".i")) + clean = CLEAN_JFFS2; + } +*/ + addr = (ulong)simple_strtoul(argv[2], NULL, 16); + + arg_off_size(argc - 3, argv + 3, &off, &size, nand->size); + if (off == 0 && size == 0) return 1; - } - printf ("\nNAND %s: device %d offset %ld, size %ld ... ", - (cmd & NANDRW_READ) ? "read" : "write", - curr_device, off, size); + i = strncmp(cmd, "read", 4) == 0; /* 1 = read, 0 = write */ + printf("\nNAND %s: device %d offset %u, size %u ... ", + i ? "read" : "write", nand_curr_device, off, size); - ret = nand_rw(nand_dev_desc + curr_device, cmd, off, size, - &total, (u_char*)addr); + if (i) + ret = nand_read(nand, off, &size, (u_char *)addr); + else + ret = nand_write(nand, off, &size, (u_char *)addr); - printf (" %d bytes %s: %s\n", total, - (cmd & NANDRW_READ) ? "read" : "written", - ret ? "ERROR" : "OK"); + printf(" %d bytes %s: %s\n", size, + i ? "read" : "written", ret ? "ERROR" : "OK"); - return ret; - } else if (strcmp(argv[1],"erase") == 0 && - (argc == 4 || strcmp("clean", argv[2]) == 0)) { - int clean = argc == 5; - ulong off = simple_strtoul(argv[2 + clean], NULL, 16); - ulong size = simple_strtoul(argv[3 + clean], NULL, 16); - int ret; + return ret == 0 ? 0 : 1; + } +#ifdef CONFIG_MTD_NAND_UNSAFE + if (strcmp(cmd, "markbad") == 0 || strcmp(cmd, "biterr") == 0) { + if (argc < 3) + goto usage; - printf ("\nNAND erase: device %d offset %ld, size %ld ... ", - curr_device, off, size); + i = strcmp(cmd, "biterr") == 0; - ret = nand_erase (nand_dev_desc + curr_device, off, size, clean); + off = (int)simple_strtoul(argv[2], NULL, 16); - printf("%s\n", ret ? "ERROR" : "OK"); + if (i) + ret = nand_make_bit_error(nand, off); + else + ret = nand_mark_bad(nand, off); - return ret; - } else { - printf ("Usage:\n%s\n", cmdtp->usage); - rcode = 1; + return ret == 0 ? 0 : 1; } +#endif - return rcode; - } +usage: + printf("Usage:\n%s\n", cmdtp->usage); + return 1; } -U_BOOT_CMD( - nand, 5, 1, do_nand, +U_BOOT_CMD(nand, 5, 1, do_nand, "nand - NAND sub-system\n", - "info - show available NAND devices\n" - "nand device [dev] - show or set current device\n" - "nand read[.jffs2[s]] addr off size\n" - "nand write[.jffs2] addr off size - read/write `size' bytes starting\n" + "info - show available NAND devices\n" + "nand device [dev] - show or set current device\n" + "nand read[.jffs2] - addr off size\n" + "nand write[.jffs2] - addr off size - read/write `size' bytes starting\n" " at offset `off' to/from memory address `addr'\n" "nand erase [clean] [off size] - erase `size' bytes from\n" " offset `off' (entire device if not specified)\n" "nand bad - show bad blocks\n" - "nand read.oob addr off size - read out-of-band data\n" - "nand write.oob addr off size - read out-of-band data\n" -); + "nand dump[.oob] off - dump page\n" + "nand scrub - really clean NAND erasing bad blocks (UNSAFE)\n" + "nand markbad off - mark bad block at offset (UNSAFE)\n" + "nand biterr off - make a bit error at offset (UNSAFE)\n"); -int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) { char *boot_device = NULL; char *ep; int dev; - ulong cnt; - ulong addr; - ulong offset = 0; + int r; + ulong addr, cnt, offset = 0; image_header_t *hdr; - int rcode = 0; + nand_info_t *nand; + switch (argc) { case 1: addr = CFG_LOAD_ADDR; - boot_device = getenv ("bootdevice"); + boot_device = getenv("bootdevice"); break; case 2: addr = simple_strtoul(argv[1], NULL, 16); - boot_device = getenv ("bootdevice"); + boot_device = getenv("bootdevice"); break; case 3: addr = simple_strtoul(argv[1], NULL, 16); @@ -315,55 +334,53 @@ int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) offset = simple_strtoul(argv[3], NULL, 16); break; default: - printf ("Usage:\n%s\n", cmdtp->usage); - SHOW_BOOT_PROGRESS (-1); + printf("Usage:\n%s\n", cmdtp->usage); + SHOW_BOOT_PROGRESS(-1); return 1; } if (!boot_device) { - puts ("\n** No boot device **\n"); - SHOW_BOOT_PROGRESS (-1); + puts("\n** No boot device **\n"); + SHOW_BOOT_PROGRESS(-1); return 1; } dev = simple_strtoul(boot_device, &ep, 16); - if ((dev >= CFG_MAX_NAND_DEVICE) || - (nand_dev_desc[dev].ChipID == NAND_ChipID_UNKNOWN)) { - printf ("\n** Device %d not available\n", dev); - SHOW_BOOT_PROGRESS (-1); + if (dev < 0 || dev >= CFG_MAX_NAND_DEVICE || !nand_info[dev].name) { + printf("\n** Device %d not available\n", dev); + SHOW_BOOT_PROGRESS(-1); return 1; } - printf ("\nLoading from device %d: %s at 0x%lx (offset 0x%lx)\n", - dev, nand_dev_desc[dev].name, nand_dev_desc[dev].IO_ADDR, - offset); + nand = &nand_info[dev]; + printf("\nLoading from device %d: %s (offset 0x%lx)\n", + dev, nand->name, offset); - if (nand_rw (nand_dev_desc + dev, NANDRW_READ, offset, - SECTORSIZE, NULL, (u_char *)addr)) { - printf ("** Read error on %d\n", dev); - SHOW_BOOT_PROGRESS (-1); + cnt = nand->oobblock; + r = nand_read(nand, offset, &cnt, (u_char *) addr); + if (r) { + printf("** Read error on %d\n", dev); + SHOW_BOOT_PROGRESS(-1); return 1; } - hdr = (image_header_t *)addr; - - if (ntohl(hdr->ih_magic) == IH_MAGIC) { + hdr = (image_header_t *) addr; - print_image_hdr (hdr); - - cnt = (ntohl(hdr->ih_size) + sizeof(image_header_t)); - cnt -= SECTORSIZE; - } else { - printf ("\n** Bad Magic Number 0x%x **\n", hdr->ih_magic); - SHOW_BOOT_PROGRESS (-1); + if (ntohl(hdr->ih_magic) != IH_MAGIC) { + printf("\n** Bad Magic Number 0x%x **\n", hdr->ih_magic); + SHOW_BOOT_PROGRESS(-1); return 1; } - if (nand_rw (nand_dev_desc + dev, NANDRW_READ, offset + SECTORSIZE, cnt, - NULL, (u_char *)(addr+SECTORSIZE))) { - printf ("** Read error on %d\n", dev); - SHOW_BOOT_PROGRESS (-1); + print_image_hdr(hdr); + + cnt = (ntohl(hdr->ih_size) + sizeof (image_header_t)); + + r = nand_read(nand, offset, &cnt, (u_char *) addr); + if (r) { + printf("** Read error on %d\n", dev); + SHOW_BOOT_PROGRESS(-1); return 1; } @@ -372,1526 +389,24 @@ int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) load_addr = addr; /* Check if we should attempt an auto-start */ - if (((ep = getenv("autostart")) != NULL) && (strcmp(ep,"yes") == 0)) { + if (((ep = getenv("autostart")) != NULL) && (strcmp(ep, "yes") == 0)) { char *local_args[2]; - extern int do_bootm (cmd_tbl_t *, int, int, char *[]); + extern int do_bootm(cmd_tbl_t *, int, int, char *[]); local_args[0] = argv[0]; local_args[1] = NULL; - printf ("Automatic boot of image at addr 0x%08lx ...\n", addr); - - do_bootm (cmdtp, 0, 1, local_args); - rcode = 1; - } - return rcode; -} - -U_BOOT_CMD( - nboot, 4, 1, do_nandboot, - "nboot - boot from NAND device\n", - "loadAddr dev\n" -); + printf("Automatic boot of image at addr 0x%08lx ...\n", addr); -/* returns 0 if block containing pos is OK: - * valid erase block and - * not marked bad, or no bad mark position is specified - * returns 1 if marked bad or otherwise invalid - */ -int check_block (struct nand_chip *nand, unsigned long pos) -{ - int retlen; - uint8_t oob_data; - uint16_t oob_data16[6]; - int page0 = pos & (-nand->erasesize); - int page1 = page0 + nand->oobblock; - int badpos = oob_config.badblock_pos; - - if (pos >= nand->totlen) + do_bootm(cmdtp, 0, 1, local_args); return 1; - - if (badpos < 0) - return 0; /* no way to check, assume OK */ - - if (nand->bus16) { - if (nand_read_oob(nand, (page0 + 0), 12, &retlen, (uint8_t *)oob_data16) - || (oob_data16[2] & 0xff00) != 0xff00) - return 1; - if (nand_read_oob(nand, (page1 + 0), 12, &retlen, (uint8_t *)oob_data16) - || (oob_data16[2] & 0xff00) != 0xff00) - return 1; - } else { - /* Note - bad block marker can be on first or second page */ - if (nand_read_oob(nand, page0 + badpos, 1, &retlen, &oob_data) - || oob_data != 0xff - || nand_read_oob (nand, page1 + badpos, 1, &retlen, &oob_data) - || oob_data != 0xff) - return 1; - } - - return 0; -} - -/* print bad blocks in NAND flash */ -static void nand_print_bad(struct nand_chip* nand) -{ - unsigned long pos; - - for (pos = 0; pos < nand->totlen; pos += nand->erasesize) { - if (check_block(nand, pos)) - printf(" 0x%8.8lx\n", pos); - } - puts("\n"); -} - -/* cmd: 0: NANDRW_WRITE write, fail on bad block - * 1: NANDRW_READ read, fail on bad block - * 2: NANDRW_WRITE | NANDRW_JFFS2 write, skip bad blocks - * 3: NANDRW_READ | NANDRW_JFFS2 read, data all 0xff for bad blocks - * 7: NANDRW_READ | NANDRW_JFFS2 | NANDRW_JFFS2_SKIP read, skip bad blocks - */ -int nand_rw (struct nand_chip* nand, int cmd, - size_t start, size_t len, - size_t * retlen, u_char * buf) -{ - int ret = 0, n, total = 0; - char eccbuf[6]; - /* eblk (once set) is the start of the erase block containing the - * data being processed. - */ - unsigned long eblk = ~0; /* force mismatch on first pass */ - unsigned long erasesize = nand->erasesize; - - while (len) { - if ((start & (-erasesize)) != eblk) { - /* have crossed into new erase block, deal with - * it if it is sure marked bad. - */ - eblk = start & (-erasesize); /* start of block */ - if (check_block(nand, eblk)) { - if (cmd == (NANDRW_READ | NANDRW_JFFS2)) { - while (len > 0 && - start - eblk < erasesize) { - *(buf++) = 0xff; - ++start; - ++total; - --len; - } - continue; - } else if (cmd == (NANDRW_READ | NANDRW_JFFS2 | NANDRW_JFFS2_SKIP)) { - start += erasesize; - continue; - } else if (cmd == (NANDRW_WRITE | NANDRW_JFFS2)) { - /* skip bad block */ - start += erasesize; - continue; - } else { - ret = 1; - break; - } - } - } - /* The ECC will not be calculated correctly if - less than 512 is written or read */ - /* Is request at least 512 bytes AND it starts on a proper boundry */ - if((start != ROUND_DOWN(start, 0x200)) || (len < 0x200)) - printf("Warning block writes should be at least 512 bytes and start on a 512 byte boundry\n"); - - if (cmd & NANDRW_READ) { - ret = nand_read_ecc(nand, start, - min(len, eblk + erasesize - start), - &n, (u_char*)buf, eccbuf); - } else { - ret = nand_write_ecc(nand, start, - min(len, eblk + erasesize - start), - &n, (u_char*)buf, eccbuf); - } - - if (ret) - break; - - start += n; - buf += n; - total += n; - len -= n; - } - if (retlen) - *retlen = total; - - return ret; -} - -static void nand_print(struct nand_chip *nand) -{ - if (nand->numchips > 1) { - printf("%s at 0x%lx,\n" - "\t %d chips %s, size %d MB, \n" - "\t total size %ld MB, sector size %ld kB\n", - nand->name, nand->IO_ADDR, nand->numchips, - nand->chips_name, 1 << (nand->chipshift - 20), - nand->totlen >> 20, nand->erasesize >> 10); - } - else { - printf("%s at 0x%lx (", nand->chips_name, nand->IO_ADDR); - print_size(nand->totlen, ", "); - print_size(nand->erasesize, " sector)\n"); - } -} - -/* ------------------------------------------------------------------------- */ - -static int NanD_WaitReady(struct nand_chip *nand, int ale_wait) -{ - /* This is inline, to optimise the common case, where it's ready instantly */ - int ret = 0; - -#ifdef NAND_NO_RB /* in config file, shorter delays currently wrap accesses */ - if(ale_wait) - NAND_WAIT_READY(nand); /* do the worst case 25us wait */ - else - udelay(10); -#else /* has functional r/b signal */ - NAND_WAIT_READY(nand); -#endif - return ret; -} - -/* NanD_Command: Send a flash command to the flash chip */ - -static inline int NanD_Command(struct nand_chip *nand, unsigned char command) -{ - unsigned long nandptr = nand->IO_ADDR; - - /* Assert the CLE (Command Latch Enable) line to the flash chip */ - NAND_CTL_SETCLE(nandptr); - - /* Send the command */ - WRITE_NAND_COMMAND(command, nandptr); - - /* Lower the CLE line */ - NAND_CTL_CLRCLE(nandptr); - -#ifdef NAND_NO_RB - if(command == NAND_CMD_RESET){ - u_char ret_val; - NanD_Command(nand, NAND_CMD_STATUS); - do { - ret_val = READ_NAND(nandptr);/* wait till ready */ - } while((ret_val & 0x40) != 0x40); - } -#endif - return NanD_WaitReady(nand, 0); -} - -/* NanD_Address: Set the current address for the flash chip */ - -static int NanD_Address(struct nand_chip *nand, int numbytes, unsigned long ofs) -{ - unsigned long nandptr; - int i; - - nandptr = nand->IO_ADDR; - - /* Assert the ALE (Address Latch Enable) line to the flash chip */ - NAND_CTL_SETALE(nandptr); - - /* Send the address */ - /* Devices with 256-byte page are addressed as: - * Column (bits 0-7), Page (bits 8-15, 16-23, 24-31) - * there is no device on the market with page256 - * and more than 24 bits. - * Devices with 512-byte page are addressed as: - * Column (bits 0-7), Page (bits 9-16, 17-24, 25-31) - * 25-31 is sent only if the chip support it. - * bit 8 changes the read command to be sent - * (NAND_CMD_READ0 or NAND_CMD_READ1). - */ - - if (numbytes == ADDR_COLUMN || numbytes == ADDR_COLUMN_PAGE) - WRITE_NAND_ADDRESS(ofs, nandptr); - - ofs = ofs >> nand->page_shift; - - if (numbytes == ADDR_PAGE || numbytes == ADDR_COLUMN_PAGE) { - for (i = 0; i < nand->pageadrlen; i++, ofs = ofs >> 8) { - WRITE_NAND_ADDRESS(ofs, nandptr); - } - } - - /* Lower the ALE line */ - NAND_CTL_CLRALE(nandptr); - - /* Wait for the chip to respond */ - return NanD_WaitReady(nand, 1); -} - -/* NanD_SelectChip: Select a given flash chip within the current floor */ - -static inline int NanD_SelectChip(struct nand_chip *nand, int chip) -{ - /* Wait for it to be ready */ - return NanD_WaitReady(nand, 0); -} - -/* NanD_IdentChip: Identify a given NAND chip given {floor,chip} */ - -static int NanD_IdentChip(struct nand_chip *nand, int floor, int chip) -{ - int mfr, id, i; - - NAND_ENABLE_CE(nand); /* set pin low */ - /* Reset the chip */ - if (NanD_Command(nand, NAND_CMD_RESET)) { -#ifdef NAND_DEBUG - printf("NanD_Command (reset) for %d,%d returned true\n", - floor, chip); -#endif - NAND_DISABLE_CE(nand); /* set pin high */ - return 0; - } - - /* Read the NAND chip ID: 1. Send ReadID command */ - if (NanD_Command(nand, NAND_CMD_READID)) { -#ifdef NAND_DEBUG - printf("NanD_Command (ReadID) for %d,%d returned true\n", - floor, chip); -#endif - NAND_DISABLE_CE(nand); /* set pin high */ - return 0; - } - - /* Read the NAND chip ID: 2. Send address byte zero */ - NanD_Address(nand, ADDR_COLUMN, 0); - - /* Read the manufacturer and device id codes from the device */ - - mfr = READ_NAND(nand->IO_ADDR); - - id = READ_NAND(nand->IO_ADDR); - - NAND_DISABLE_CE(nand); /* set pin high */ - -#ifdef NAND_DEBUG - printf("NanD_Command (ReadID) got %x %x\n", mfr, id); -#endif - if (mfr == 0xff || mfr == 0) { - /* No response - return failure */ - return 0; - } - - /* Check it's the same as the first chip we identified. - * M-Systems say that any given nand_chip device should only - * contain _one_ type of flash part, although that's not a - * hardware restriction. */ - if (nand->mfr) { - if (nand->mfr == mfr && nand->id == id) { - return 1; /* This is another the same the first */ - } else { - printf("Flash chip at floor %d, chip %d is different:\n", - floor, chip); - } - } - - /* Print and store the manufacturer and ID codes. */ - for (i = 0; nand_flash_ids[i].name != NULL; i++) { - if (mfr == nand_flash_ids[i].manufacture_id && - id == nand_flash_ids[i].model_id) { -#ifdef NAND_DEBUG - printf("Flash chip found:\n\t Manufacturer ID: 0x%2.2X, " - "Chip ID: 0x%2.2X (%s)\n", mfr, id, - nand_flash_ids[i].name); -#endif - if (!nand->mfr) { - nand->mfr = mfr; - nand->id = id; - nand->chipshift = - nand_flash_ids[i].chipshift; - nand->page256 = nand_flash_ids[i].page256; - nand->eccsize = 256; - if (nand->page256) { - nand->oobblock = 256; - nand->oobsize = 8; - nand->page_shift = 8; - } else { - nand->oobblock = 512; - nand->oobsize = 16; - nand->page_shift = 9; - } - nand->pageadrlen = nand_flash_ids[i].pageadrlen; - nand->erasesize = nand_flash_ids[i].erasesize; - nand->chips_name = nand_flash_ids[i].name; - nand->bus16 = nand_flash_ids[i].bus16; - return 1; - } - return 0; - } - } - - -#ifdef NAND_DEBUG - /* We haven't fully identified the chip. Print as much as we know. */ - printf("Unknown flash chip found: %2.2X %2.2X\n", - id, mfr); -#endif - - return 0; -} - -/* NanD_ScanChips: Find all NAND chips present in a nand_chip, and identify them */ - -static void NanD_ScanChips(struct nand_chip *nand) -{ - int floor, chip; - int numchips[NAND_MAX_FLOORS]; - int maxchips = NAND_MAX_CHIPS; - int ret = 1; - - nand->numchips = 0; - nand->mfr = 0; - nand->id = 0; - - - /* For each floor, find the number of valid chips it contains */ - for (floor = 0; floor < NAND_MAX_FLOORS; floor++) { - ret = 1; - numchips[floor] = 0; - for (chip = 0; chip < maxchips && ret != 0; chip++) { - - ret = NanD_IdentChip(nand, floor, chip); - if (ret) { - numchips[floor]++; - nand->numchips++; - } - } - } - - /* If there are none at all that we recognise, bail */ - if (!nand->numchips) { -#ifdef NAND_DEBUG - puts ("No NAND flash chips recognised.\n"); -#endif - return; - } - - /* Allocate an array to hold the information for each chip */ - nand->chips = malloc(sizeof(struct Nand) * nand->numchips); - if (!nand->chips) { - puts ("No memory for allocating chip info structures\n"); - return; - } - - ret = 0; - - /* Fill out the chip array with {floor, chipno} for each - * detected chip in the device. */ - for (floor = 0; floor < NAND_MAX_FLOORS; floor++) { - for (chip = 0; chip < numchips[floor]; chip++) { - nand->chips[ret].floor = floor; - nand->chips[ret].chip = chip; - nand->chips[ret].curadr = 0; - nand->chips[ret].curmode = 0x50; - ret++; - } - } - - /* Calculate and print the total size of the device */ - nand->totlen = nand->numchips * (1 << nand->chipshift); - -#ifdef NAND_DEBUG - printf("%d flash chips found. Total nand_chip size: %ld MB\n", - nand->numchips, nand->totlen >> 20); -#endif -} - -/* we need to be fast here, 1 us per read translates to 1 second per meg */ -static void NanD_ReadBuf (struct nand_chip *nand, u_char * data_buf, int cntr) -{ - unsigned long nandptr = nand->IO_ADDR; - - NanD_Command (nand, NAND_CMD_READ0); - - if (nand->bus16) { - u16 val; - - while (cntr >= 16) { - val = READ_NAND (nandptr); - *data_buf++ = val & 0xff; - *data_buf++ = val >> 8; - val = READ_NAND (nandptr); - *data_buf++ = val & 0xff; - *data_buf++ = val >> 8; - val = READ_NAND (nandptr); - *data_buf++ = val & 0xff; - *data_buf++ = val >> 8; - val = READ_NAND (nandptr); - *data_buf++ = val & 0xff; - *data_buf++ = val >> 8; - val = READ_NAND (nandptr); - *data_buf++ = val & 0xff; - *data_buf++ = val >> 8; - val = READ_NAND (nandptr); - *data_buf++ = val & 0xff; - *data_buf++ = val >> 8; - val = READ_NAND (nandptr); - *data_buf++ = val & 0xff; - *data_buf++ = val >> 8; - val = READ_NAND (nandptr); - *data_buf++ = val & 0xff; - *data_buf++ = val >> 8; - cntr -= 16; - } - - while (cntr > 0) { - val = READ_NAND (nandptr); - *data_buf++ = val & 0xff; - *data_buf++ = val >> 8; - cntr -= 2; - } - } else { - while (cntr >= 16) { - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - *data_buf++ = READ_NAND (nandptr); - cntr -= 16; - } - - while (cntr > 0) { - *data_buf++ = READ_NAND (nandptr); - cntr--; - } - } -} - -/* - * NAND read with ECC - */ -static int nand_read_ecc(struct nand_chip *nand, size_t start, size_t len, - size_t * retlen, u_char *buf, u_char *ecc_code) -{ - int col, page; - int ecc_status = 0; -#ifdef CONFIG_MTD_NAND_ECC - int j; - int ecc_failed = 0; - u_char *data_poi; - u_char ecc_calc[6]; -#endif - - /* Do not allow reads past end of device */ - if ((start + len) > nand->totlen) { - printf ("%s: Attempt read beyond end of device %x %x %x\n", - __FUNCTION__, (uint) start, (uint) len, (uint) nand->totlen); - *retlen = 0; - return -1; } - - /* First we calculate the starting page */ - /*page = shr(start, nand->page_shift);*/ - page = start >> nand->page_shift; - - /* Get raw starting column */ - col = start & (nand->oobblock - 1); - - /* Initialize return value */ - *retlen = 0; - - /* Select the NAND device */ - NAND_ENABLE_CE(nand); /* set pin low */ - - /* Loop until all data read */ - while (*retlen < len) { - -#ifdef CONFIG_MTD_NAND_ECC - /* Do we have this page in cache ? */ - if (nand->cache_page == page) - goto readdata; - /* Send the read command */ - NanD_Command(nand, NAND_CMD_READ0); - if (nand->bus16) { - NanD_Address(nand, ADDR_COLUMN_PAGE, - (page << nand->page_shift) + (col >> 1)); - } else { - NanD_Address(nand, ADDR_COLUMN_PAGE, - (page << nand->page_shift) + col); - } - - /* Read in a page + oob data */ - NanD_ReadBuf(nand, nand->data_buf, nand->oobblock + nand->oobsize); - - /* copy data into cache, for read out of cache and if ecc fails */ - if (nand->data_cache) { - memcpy (nand->data_cache, nand->data_buf, - nand->oobblock + nand->oobsize); - } - - /* Pick the ECC bytes out of the oob data */ - for (j = 0; j < 6; j++) { - ecc_code[j] = nand->data_buf[(nand->oobblock + oob_config.ecc_pos[j])]; - } - - /* Calculate the ECC and verify it */ - /* If block was not written with ECC, skip ECC */ - if (oob_config.eccvalid_pos != -1 && - (nand->data_buf[nand->oobblock + oob_config.eccvalid_pos] & 0x0f) != 0x0f) { - - nand_calculate_ecc (&nand->data_buf[0], &ecc_calc[0]); - switch (nand_correct_data (&nand->data_buf[0], &ecc_code[0], &ecc_calc[0])) { - case -1: - printf ("%s: Failed ECC read, page 0x%08x\n", __FUNCTION__, page); - ecc_failed++; - break; - case 1: - case 2: /* transfer ECC corrected data to cache */ - if (nand->data_cache) - memcpy (nand->data_cache, nand->data_buf, 256); - break; - } - } - - if (oob_config.eccvalid_pos != -1 && - nand->oobblock == 512 && (nand->data_buf[nand->oobblock + oob_config.eccvalid_pos] & 0xf0) != 0xf0) { - - nand_calculate_ecc (&nand->data_buf[256], &ecc_calc[3]); - switch (nand_correct_data (&nand->data_buf[256], &ecc_code[3], &ecc_calc[3])) { - case -1: - printf ("%s: Failed ECC read, page 0x%08x\n", __FUNCTION__, page); - ecc_failed++; - break; - case 1: - case 2: /* transfer ECC corrected data to cache */ - if (nand->data_cache) - memcpy (&nand->data_cache[256], &nand->data_buf[256], 256); - break; - } - } -readdata: - /* Read the data from ECC data buffer into return buffer */ - data_poi = (nand->data_cache) ? nand->data_cache : nand->data_buf; - data_poi += col; - if ((*retlen + (nand->oobblock - col)) >= len) { - memcpy (buf + *retlen, data_poi, len - *retlen); - *retlen = len; - } else { - memcpy (buf + *retlen, data_poi, nand->oobblock - col); - *retlen += nand->oobblock - col; - } - /* Set cache page address, invalidate, if ecc_failed */ - nand->cache_page = (nand->data_cache && !ecc_failed) ? page : -1; - - ecc_status += ecc_failed; - ecc_failed = 0; - -#else - /* Send the read command */ - NanD_Command(nand, NAND_CMD_READ0); - if (nand->bus16) { - NanD_Address(nand, ADDR_COLUMN_PAGE, - (page << nand->page_shift) + (col >> 1)); - } else { - NanD_Address(nand, ADDR_COLUMN_PAGE, - (page << nand->page_shift) + col); - } - - /* Read the data directly into the return buffer */ - if ((*retlen + (nand->oobblock - col)) >= len) { - NanD_ReadBuf(nand, buf + *retlen, len - *retlen); - *retlen = len; - /* We're done */ - continue; - } else { - NanD_ReadBuf(nand, buf + *retlen, nand->oobblock - col); - *retlen += nand->oobblock - col; - } -#endif - /* For subsequent reads align to page boundary. */ - col = 0; - /* Increment page address */ - page++; - } - - /* De-select the NAND device */ - NAND_DISABLE_CE(nand); /* set pin high */ - - /* - * Return success, if no ECC failures, else -EIO - * fs driver will take care of that, because - * retlen == desired len and result == -EIO - */ - return ecc_status ? -1 : 0; -} - -/* - * Nand_page_program function is used for write and writev ! - */ -static int nand_write_page (struct nand_chip *nand, - int page, int col, int last, u_char * ecc_code) -{ - - int i; - unsigned long nandptr = nand->IO_ADDR; - -#ifdef CONFIG_MTD_NAND_ECC -#ifdef CONFIG_MTD_NAND_VERIFY_WRITE - int ecc_bytes = (nand->oobblock == 512) ? 6 : 3; -#endif -#endif - /* pad oob area */ - for (i = nand->oobblock; i < nand->oobblock + nand->oobsize; i++) - nand->data_buf[i] = 0xff; - -#ifdef CONFIG_MTD_NAND_ECC - /* Zero out the ECC array */ - for (i = 0; i < 6; i++) - ecc_code[i] = 0x00; - - /* Read back previous written data, if col > 0 */ - if (col) { - NanD_Command (nand, NAND_CMD_READ0); - if (nand->bus16) { - NanD_Address (nand, ADDR_COLUMN_PAGE, - (page << nand->page_shift) + (col >> 1)); - } else { - NanD_Address (nand, ADDR_COLUMN_PAGE, - (page << nand->page_shift) + col); - } - - if (nand->bus16) { - u16 val; - - for (i = 0; i < col; i += 2) { - val = READ_NAND (nandptr); - nand->data_buf[i] = val & 0xff; - nand->data_buf[i + 1] = val >> 8; - } - } else { - for (i = 0; i < col; i++) - nand->data_buf[i] = READ_NAND (nandptr); - } - } - - /* Calculate and write the ECC if we have enough data */ - if ((col < nand->eccsize) && (last >= nand->eccsize)) { - nand_calculate_ecc (&nand->data_buf[0], &(ecc_code[0])); - for (i = 0; i < 3; i++) { - nand->data_buf[(nand->oobblock + - oob_config.ecc_pos[i])] = ecc_code[i]; - } - if (oob_config.eccvalid_pos != -1) { - nand->data_buf[nand->oobblock + - oob_config.eccvalid_pos] = 0xf0; - } - } - - /* Calculate and write the second ECC if we have enough data */ - if ((nand->oobblock == 512) && (last == nand->oobblock)) { - nand_calculate_ecc (&nand->data_buf[256], &(ecc_code[3])); - for (i = 3; i < 6; i++) { - nand->data_buf[(nand->oobblock + - oob_config.ecc_pos[i])] = ecc_code[i]; - } - if (oob_config.eccvalid_pos != -1) { - nand->data_buf[nand->oobblock + - oob_config.eccvalid_pos] &= 0x0f; - } - } -#endif - /* Prepad for partial page programming !!! */ - for (i = 0; i < col; i++) - nand->data_buf[i] = 0xff; - - /* Postpad for partial page programming !!! oob is already padded */ - for (i = last; i < nand->oobblock; i++) - nand->data_buf[i] = 0xff; - - /* Send command to begin auto page programming */ - NanD_Command (nand, NAND_CMD_READ0); - NanD_Command (nand, NAND_CMD_SEQIN); - if (nand->bus16) { - NanD_Address (nand, ADDR_COLUMN_PAGE, - (page << nand->page_shift) + (col >> 1)); - } else { - NanD_Address (nand, ADDR_COLUMN_PAGE, - (page << nand->page_shift) + col); - } - - /* Write out complete page of data */ - if (nand->bus16) { - for (i = 0; i < (nand->oobblock + nand->oobsize); i += 2) { - WRITE_NAND (nand->data_buf[i] + - (nand->data_buf[i + 1] << 8), - nand->IO_ADDR); - } - } else { - for (i = 0; i < (nand->oobblock + nand->oobsize); i++) - WRITE_NAND (nand->data_buf[i], nand->IO_ADDR); - } - - /* Send command to actually program the data */ - NanD_Command (nand, NAND_CMD_PAGEPROG); - NanD_Command (nand, NAND_CMD_STATUS); -#ifdef NAND_NO_RB - { - u_char ret_val; - - do { - ret_val = READ_NAND (nandptr); /* wait till ready */ - } while ((ret_val & 0x40) != 0x40); - } -#endif - /* See if device thinks it succeeded */ - if (READ_NAND (nand->IO_ADDR) & 0x01) { - printf ("%s: Failed write, page 0x%08x, ", __FUNCTION__, - page); - return -1; - } -#ifdef CONFIG_MTD_NAND_VERIFY_WRITE - /* - * The NAND device assumes that it is always writing to - * a cleanly erased page. Hence, it performs its internal - * write verification only on bits that transitioned from - * 1 to 0. The device does NOT verify the whole page on a - * byte by byte basis. It is possible that the page was - * not completely erased or the page is becoming unusable - * due to wear. The read with ECC would catch the error - * later when the ECC page check fails, but we would rather - * catch it early in the page write stage. Better to write - * no data than invalid data. - */ - - /* Send command to read back the page */ - if (col < nand->eccsize) - NanD_Command (nand, NAND_CMD_READ0); - else - NanD_Command (nand, NAND_CMD_READ1); - if (nand->bus16) { - NanD_Address (nand, ADDR_COLUMN_PAGE, - (page << nand->page_shift) + (col >> 1)); - } else { - NanD_Address (nand, ADDR_COLUMN_PAGE, - (page << nand->page_shift) + col); - } - - /* Loop through and verify the data */ - if (nand->bus16) { - for (i = col; i < last; i = +2) { - if ((nand->data_buf[i] + - (nand->data_buf[i + 1] << 8)) != READ_NAND (nand->IO_ADDR)) { - printf ("%s: Failed write verify, page 0x%08x ", - __FUNCTION__, page); - return -1; - } - } - } else { - for (i = col; i < last; i++) { - if (nand->data_buf[i] != READ_NAND (nand->IO_ADDR)) { - printf ("%s: Failed write verify, page 0x%08x ", - __FUNCTION__, page); - return -1; - } - } - } - -#ifdef CONFIG_MTD_NAND_ECC - /* - * We also want to check that the ECC bytes wrote - * correctly for the same reasons stated above. - */ - NanD_Command (nand, NAND_CMD_READOOB); - if (nand->bus16) { - NanD_Address (nand, ADDR_COLUMN_PAGE, - (page << nand->page_shift) + (col >> 1)); - } else { - NanD_Address (nand, ADDR_COLUMN_PAGE, - (page << nand->page_shift) + col); - } - if (nand->bus16) { - for (i = 0; i < nand->oobsize; i += 2) { - u16 val; - - val = READ_NAND (nand->IO_ADDR); - nand->data_buf[i] = val & 0xff; - nand->data_buf[i + 1] = val >> 8; - } - } else { - for (i = 0; i < nand->oobsize; i++) { - nand->data_buf[i] = READ_NAND (nand->IO_ADDR); - } - } - for (i = 0; i < ecc_bytes; i++) { - if ((nand->data_buf[(oob_config.ecc_pos[i])] != ecc_code[i]) && ecc_code[i]) { - printf ("%s: Failed ECC write " - "verify, page 0x%08x, " - "%6i bytes were succesful\n", - __FUNCTION__, page, i); - return -1; - } - } -#endif /* CONFIG_MTD_NAND_ECC */ -#endif /* CONFIG_MTD_NAND_VERIFY_WRITE */ return 0; } -static int nand_write_ecc (struct nand_chip* nand, size_t to, size_t len, - size_t * retlen, const u_char * buf, u_char * ecc_code) -{ - int i, page, col, cnt, ret = 0; - - /* Do not allow write past end of device */ - if ((to + len) > nand->totlen) { - printf ("%s: Attempt to write past end of page\n", __FUNCTION__); - return -1; - } - - /* Shift to get page */ - page = ((int) to) >> nand->page_shift; - - /* Get the starting column */ - col = to & (nand->oobblock - 1); - - /* Initialize return length value */ - *retlen = 0; - - /* Select the NAND device */ -#ifdef CONFIG_OMAP1510 - archflashwp(0,0); -#endif -#ifdef CFG_NAND_WP - NAND_WP_OFF(); -#endif - - NAND_ENABLE_CE(nand); /* set pin low */ - - /* Check the WP bit */ - NanD_Command(nand, NAND_CMD_STATUS); - if (!(READ_NAND(nand->IO_ADDR) & 0x80)) { - printf ("%s: Device is write protected!!!\n", __FUNCTION__); - ret = -1; - goto out; - } - - /* Loop until all data is written */ - while (*retlen < len) { - /* Invalidate cache, if we write to this page */ - if (nand->cache_page == page) - nand->cache_page = -1; - - /* Write data into buffer */ - if ((col + len) >= nand->oobblock) { - for (i = col, cnt = 0; i < nand->oobblock; i++, cnt++) { - nand->data_buf[i] = buf[(*retlen + cnt)]; - } - } else { - for (i = col, cnt = 0; cnt < (len - *retlen); i++, cnt++) { - nand->data_buf[i] = buf[(*retlen + cnt)]; - } - } - /* We use the same function for write and writev !) */ - ret = nand_write_page (nand, page, col, i, ecc_code); - if (ret) - goto out; - - /* Next data start at page boundary */ - col = 0; - - /* Update written bytes count */ - *retlen += cnt; - - /* Increment page address */ - page++; - } - - /* Return happy */ - *retlen = len; - -out: - /* De-select the NAND device */ - NAND_DISABLE_CE(nand); /* set pin high */ -#ifdef CONFIG_OMAP1510 - archflashwp(0,1); -#endif -#ifdef CFG_NAND_WP - NAND_WP_ON(); -#endif - - return ret; -} - -/* read from the 16 bytes of oob data that correspond to a 512 byte - * page or 2 256-byte pages. - */ -static int nand_read_oob(struct nand_chip* nand, size_t ofs, size_t len, - size_t * retlen, u_char * buf) -{ - int len256 = 0; - struct Nand *mychip; - int ret = 0; - - mychip = &nand->chips[ofs >> nand->chipshift]; - - /* update address for 2M x 8bit devices. OOB starts on the second */ - /* page to maintain compatibility with nand_read_ecc. */ - if (nand->page256) { - if (!(ofs & 0x8)) - ofs += 0x100; - else - ofs -= 0x8; - } - - NAND_ENABLE_CE(nand); /* set pin low */ - NanD_Command(nand, NAND_CMD_READOOB); - if (nand->bus16) { - NanD_Address(nand, ADDR_COLUMN_PAGE, - ((ofs >> nand->page_shift) << nand->page_shift) + - ((ofs & (nand->oobblock - 1)) >> 1)); - } else { - NanD_Address(nand, ADDR_COLUMN_PAGE, ofs); - } - - /* treat crossing 8-byte OOB data for 2M x 8bit devices */ - /* Note: datasheet says it should automaticaly wrap to the */ - /* next OOB block, but it didn't work here. mf. */ - if (nand->page256 && ofs + len > (ofs | 0x7) + 1) { - len256 = (ofs | 0x7) + 1 - ofs; - NanD_ReadBuf(nand, buf, len256); - - NanD_Command(nand, NAND_CMD_READOOB); - NanD_Address(nand, ADDR_COLUMN_PAGE, ofs & (~0x1ff)); - } - - NanD_ReadBuf(nand, &buf[len256], len - len256); - - *retlen = len; - /* Reading the full OOB data drops us off of the end of the page, - * causing the flash device to go into busy mode, so we need - * to wait until ready 11.4.1 and Toshiba TC58256FT nands */ - - ret = NanD_WaitReady(nand, 1); - NAND_DISABLE_CE(nand); /* set pin high */ - - return ret; - -} - -/* write to the 16 bytes of oob data that correspond to a 512 byte - * page or 2 256-byte pages. - */ -static int nand_write_oob(struct nand_chip* nand, size_t ofs, size_t len, - size_t * retlen, const u_char * buf) -{ - int len256 = 0; - int i; - unsigned long nandptr = nand->IO_ADDR; - -#ifdef PSYCHO_DEBUG - printf("nand_write_oob(%lx, %d): %2.2X %2.2X %2.2X %2.2X ... %2.2X %2.2X .. %2.2X %2.2X\n", - (long)ofs, len, buf[0], buf[1], buf[2], buf[3], - buf[8], buf[9], buf[14],buf[15]); -#endif - - NAND_ENABLE_CE(nand); /* set pin low to enable chip */ - - /* Reset the chip */ - NanD_Command(nand, NAND_CMD_RESET); - - /* issue the Read2 command to set the pointer to the Spare Data Area. */ - NanD_Command(nand, NAND_CMD_READOOB); - if (nand->bus16) { - NanD_Address(nand, ADDR_COLUMN_PAGE, - ((ofs >> nand->page_shift) << nand->page_shift) + - ((ofs & (nand->oobblock - 1)) >> 1)); - } else { - NanD_Address(nand, ADDR_COLUMN_PAGE, ofs); - } - - /* update address for 2M x 8bit devices. OOB starts on the second */ - /* page to maintain compatibility with nand_read_ecc. */ - if (nand->page256) { - if (!(ofs & 0x8)) - ofs += 0x100; - else - ofs -= 0x8; - } - - /* issue the Serial Data In command to initial the Page Program process */ - NanD_Command(nand, NAND_CMD_SEQIN); - if (nand->bus16) { - NanD_Address(nand, ADDR_COLUMN_PAGE, - ((ofs >> nand->page_shift) << nand->page_shift) + - ((ofs & (nand->oobblock - 1)) >> 1)); - } else { - NanD_Address(nand, ADDR_COLUMN_PAGE, ofs); - } - - /* treat crossing 8-byte OOB data for 2M x 8bit devices */ - /* Note: datasheet says it should automaticaly wrap to the */ - /* next OOB block, but it didn't work here. mf. */ - if (nand->page256 && ofs + len > (ofs | 0x7) + 1) { - len256 = (ofs | 0x7) + 1 - ofs; - for (i = 0; i < len256; i++) - WRITE_NAND(buf[i], nandptr); - - NanD_Command(nand, NAND_CMD_PAGEPROG); - NanD_Command(nand, NAND_CMD_STATUS); -#ifdef NAND_NO_RB - { u_char ret_val; - do { - ret_val = READ_NAND(nandptr); /* wait till ready */ - } while ((ret_val & 0x40) != 0x40); - } -#endif - if (READ_NAND(nandptr) & 1) { - puts ("Error programming oob data\n"); - /* There was an error */ - NAND_DISABLE_CE(nand); /* set pin high */ - *retlen = 0; - return -1; - } - NanD_Command(nand, NAND_CMD_SEQIN); - NanD_Address(nand, ADDR_COLUMN_PAGE, ofs & (~0x1ff)); - } - - if (nand->bus16) { - for (i = len256; i < len; i += 2) { - WRITE_NAND(buf[i] + (buf[i+1] << 8), nandptr); - } - } else { - for (i = len256; i < len; i++) - WRITE_NAND(buf[i], nandptr); - } - - NanD_Command(nand, NAND_CMD_PAGEPROG); - NanD_Command(nand, NAND_CMD_STATUS); -#ifdef NAND_NO_RB - { u_char ret_val; - do { - ret_val = READ_NAND(nandptr); /* wait till ready */ - } while ((ret_val & 0x40) != 0x40); - } -#endif - if (READ_NAND(nandptr) & 1) { - puts ("Error programming oob data\n"); - /* There was an error */ - NAND_DISABLE_CE(nand); /* set pin high */ - *retlen = 0; - return -1; - } - - NAND_DISABLE_CE(nand); /* set pin high */ - *retlen = len; - return 0; - -} - -int nand_erase(struct nand_chip* nand, size_t ofs, size_t len, int clean) -{ - /* This is defined as a structure so it will work on any system - * using native endian jffs2 (the default). - */ - static struct jffs2_unknown_node clean_marker = { - JFFS2_MAGIC_BITMASK, - JFFS2_NODETYPE_CLEANMARKER, - 8 /* 8 bytes in this node */ - }; - unsigned long nandptr; - struct Nand *mychip; - int ret = 0; - - if (ofs & (nand->erasesize-1) || len & (nand->erasesize-1)) { - printf ("Offset and size must be sector aligned, erasesize = %d\n", - (int) nand->erasesize); - return -1; - } - - nandptr = nand->IO_ADDR; - - /* Select the NAND device */ -#ifdef CONFIG_OMAP1510 - archflashwp(0,0); -#endif -#ifdef CFG_NAND_WP - NAND_WP_OFF(); -#endif - NAND_ENABLE_CE(nand); /* set pin low */ - - /* Check the WP bit */ - NanD_Command(nand, NAND_CMD_STATUS); - if (!(READ_NAND(nand->IO_ADDR) & 0x80)) { - printf ("nand_write_ecc: Device is write protected!!!\n"); - ret = -1; - goto out; - } - - /* Check the WP bit */ - NanD_Command(nand, NAND_CMD_STATUS); - if (!(READ_NAND(nand->IO_ADDR) & 0x80)) { - printf ("%s: Device is write protected!!!\n", __FUNCTION__); - ret = -1; - goto out; - } - - /* FIXME: Do nand in the background. Use timers or schedule_task() */ - while(len) { - /*mychip = &nand->chips[shr(ofs, nand->chipshift)];*/ - mychip = &nand->chips[ofs >> nand->chipshift]; - - /* always check for bad block first, genuine bad blocks - * should _never_ be erased. - */ - if (ALLOW_ERASE_BAD_DEBUG || !check_block(nand, ofs)) { - /* Select the NAND device */ - NAND_ENABLE_CE(nand); /* set pin low */ - - NanD_Command(nand, NAND_CMD_ERASE1); - NanD_Address(nand, ADDR_PAGE, ofs); - NanD_Command(nand, NAND_CMD_ERASE2); - - NanD_Command(nand, NAND_CMD_STATUS); - -#ifdef NAND_NO_RB - { u_char ret_val; - do { - ret_val = READ_NAND(nandptr); /* wait till ready */ - } while ((ret_val & 0x40) != 0x40); - } -#endif - if (READ_NAND(nandptr) & 1) { - printf ("%s: Error erasing at 0x%lx\n", - __FUNCTION__, (long)ofs); - /* There was an error */ - ret = -1; - goto out; - } - if (clean) { - int n; /* return value not used */ - int p, l; - - /* clean marker position and size depend - * on the page size, since 256 byte pages - * only have 8 bytes of oob data - */ - if (nand->page256) { - p = NAND_JFFS2_OOB8_FSDAPOS; - l = NAND_JFFS2_OOB8_FSDALEN; - } else { - p = NAND_JFFS2_OOB16_FSDAPOS; - l = NAND_JFFS2_OOB16_FSDALEN; - } - - ret = nand_write_oob(nand, ofs + p, l, &n, - (u_char *)&clean_marker); - /* quit here if write failed */ - if (ret) - goto out; - } - } - ofs += nand->erasesize; - len -= nand->erasesize; - } - -out: - /* De-select the NAND device */ - NAND_DISABLE_CE(nand); /* set pin high */ -#ifdef CONFIG_OMAP1510 - archflashwp(0,1); -#endif -#ifdef CFG_NAND_WP - NAND_WP_ON(); -#endif - - return ret; -} - -static inline int nandcheck(unsigned long potential, unsigned long physadr) -{ - return 0; -} - -unsigned long nand_probe(unsigned long physadr) -{ - struct nand_chip *nand = NULL; - int i = 0, ChipID = 1; - -#ifdef CONFIG_MTD_NAND_ECC_JFFS2 - oob_config.ecc_pos[0] = NAND_JFFS2_OOB_ECCPOS0; - oob_config.ecc_pos[1] = NAND_JFFS2_OOB_ECCPOS1; - oob_config.ecc_pos[2] = NAND_JFFS2_OOB_ECCPOS2; - oob_config.ecc_pos[3] = NAND_JFFS2_OOB_ECCPOS3; - oob_config.ecc_pos[4] = NAND_JFFS2_OOB_ECCPOS4; - oob_config.ecc_pos[5] = NAND_JFFS2_OOB_ECCPOS5; - oob_config.eccvalid_pos = 4; -#else - oob_config.ecc_pos[0] = NAND_NOOB_ECCPOS0; - oob_config.ecc_pos[1] = NAND_NOOB_ECCPOS1; - oob_config.ecc_pos[2] = NAND_NOOB_ECCPOS2; - oob_config.ecc_pos[3] = NAND_NOOB_ECCPOS3; - oob_config.ecc_pos[4] = NAND_NOOB_ECCPOS4; - oob_config.ecc_pos[5] = NAND_NOOB_ECCPOS5; - oob_config.eccvalid_pos = NAND_NOOB_ECCVPOS; -#endif - oob_config.badblock_pos = 5; - - for (i=0; iIO_ADDR = physadr; - nand->cache_page = -1; /* init the cache page */ - NanD_ScanChips(nand); - - if (nand->totlen == 0) { - /* no chips found, clean up and quit */ - memset((char *)nand, 0, sizeof(struct nand_chip)); - nand->ChipID = NAND_ChipID_UNKNOWN; - return (0); - } - - nand->ChipID = ChipID; - if (curr_device == -1) - curr_device = i; - - nand->data_buf = malloc (nand->oobblock + nand->oobsize); - if (!nand->data_buf) { - puts ("Cannot allocate memory for data structures.\n"); - return (0); - } - - return (nand->totlen); -} - -#ifdef CONFIG_MTD_NAND_ECC -/* - * Pre-calculated 256-way 1 byte column parity - */ -static const u_char nand_ecc_precalc_table[] = { - 0x00, 0x55, 0x56, 0x03, 0x59, 0x0c, 0x0f, 0x5a, - 0x5a, 0x0f, 0x0c, 0x59, 0x03, 0x56, 0x55, 0x00, - 0x65, 0x30, 0x33, 0x66, 0x3c, 0x69, 0x6a, 0x3f, - 0x3f, 0x6a, 0x69, 0x3c, 0x66, 0x33, 0x30, 0x65, - 0x66, 0x33, 0x30, 0x65, 0x3f, 0x6a, 0x69, 0x3c, - 0x3c, 0x69, 0x6a, 0x3f, 0x65, 0x30, 0x33, 0x66, - 0x03, 0x56, 0x55, 0x00, 0x5a, 0x0f, 0x0c, 0x59, - 0x59, 0x0c, 0x0f, 0x5a, 0x00, 0x55, 0x56, 0x03, - 0x69, 0x3c, 0x3f, 0x6a, 0x30, 0x65, 0x66, 0x33, - 0x33, 0x66, 0x65, 0x30, 0x6a, 0x3f, 0x3c, 0x69, - 0x0c, 0x59, 0x5a, 0x0f, 0x55, 0x00, 0x03, 0x56, - 0x56, 0x03, 0x00, 0x55, 0x0f, 0x5a, 0x59, 0x0c, - 0x0f, 0x5a, 0x59, 0x0c, 0x56, 0x03, 0x00, 0x55, - 0x55, 0x00, 0x03, 0x56, 0x0c, 0x59, 0x5a, 0x0f, - 0x6a, 0x3f, 0x3c, 0x69, 0x33, 0x66, 0x65, 0x30, - 0x30, 0x65, 0x66, 0x33, 0x69, 0x3c, 0x3f, 0x6a, - 0x6a, 0x3f, 0x3c, 0x69, 0x33, 0x66, 0x65, 0x30, - 0x30, 0x65, 0x66, 0x33, 0x69, 0x3c, 0x3f, 0x6a, - 0x0f, 0x5a, 0x59, 0x0c, 0x56, 0x03, 0x00, 0x55, - 0x55, 0x00, 0x03, 0x56, 0x0c, 0x59, 0x5a, 0x0f, - 0x0c, 0x59, 0x5a, 0x0f, 0x55, 0x00, 0x03, 0x56, - 0x56, 0x03, 0x00, 0x55, 0x0f, 0x5a, 0x59, 0x0c, - 0x69, 0x3c, 0x3f, 0x6a, 0x30, 0x65, 0x66, 0x33, - 0x33, 0x66, 0x65, 0x30, 0x6a, 0x3f, 0x3c, 0x69, - 0x03, 0x56, 0x55, 0x00, 0x5a, 0x0f, 0x0c, 0x59, - 0x59, 0x0c, 0x0f, 0x5a, 0x00, 0x55, 0x56, 0x03, - 0x66, 0x33, 0x30, 0x65, 0x3f, 0x6a, 0x69, 0x3c, - 0x3c, 0x69, 0x6a, 0x3f, 0x65, 0x30, 0x33, 0x66, - 0x65, 0x30, 0x33, 0x66, 0x3c, 0x69, 0x6a, 0x3f, - 0x3f, 0x6a, 0x69, 0x3c, 0x66, 0x33, 0x30, 0x65, - 0x00, 0x55, 0x56, 0x03, 0x59, 0x0c, 0x0f, 0x5a, - 0x5a, 0x0f, 0x0c, 0x59, 0x03, 0x56, 0x55, 0x00 -}; - - -/* - * Creates non-inverted ECC code from line parity - */ -static void nand_trans_result(u_char reg2, u_char reg3, - u_char *ecc_code) -{ - u_char a, b, i, tmp1, tmp2; - - /* Initialize variables */ - a = b = 0x80; - tmp1 = tmp2 = 0; - - /* Calculate first ECC byte */ - for (i = 0; i < 4; i++) { - if (reg3 & a) /* LP15,13,11,9 --> ecc_code[0] */ - tmp1 |= b; - b >>= 1; - if (reg2 & a) /* LP14,12,10,8 --> ecc_code[0] */ - tmp1 |= b; - b >>= 1; - a >>= 1; - } - - /* Calculate second ECC byte */ - b = 0x80; - for (i = 0; i < 4; i++) { - if (reg3 & a) /* LP7,5,3,1 --> ecc_code[1] */ - tmp2 |= b; - b >>= 1; - if (reg2 & a) /* LP6,4,2,0 --> ecc_code[1] */ - tmp2 |= b; - b >>= 1; - a >>= 1; - } - - /* Store two of the ECC bytes */ - ecc_code[0] = tmp1; - ecc_code[1] = tmp2; -} - -/* - * Calculate 3 byte ECC code for 256 byte block - */ -static void nand_calculate_ecc (const u_char *dat, u_char *ecc_code) -{ - u_char idx, reg1, reg3; - int j; - - /* Initialize variables */ - reg1 = reg3 = 0; - ecc_code[0] = ecc_code[1] = ecc_code[2] = 0; - - /* Build up column parity */ - for(j = 0; j < 256; j++) { - - /* Get CP0 - CP5 from table */ - idx = nand_ecc_precalc_table[dat[j]]; - reg1 ^= idx; - - /* All bit XOR = 1 ? */ - if (idx & 0x40) { - reg3 ^= (u_char) j; - } - } - - /* Create non-inverted ECC code from line parity */ - nand_trans_result((reg1 & 0x40) ? ~reg3 : reg3, reg3, ecc_code); - - /* Calculate final ECC code */ - ecc_code[0] = ~ecc_code[0]; - ecc_code[1] = ~ecc_code[1]; - ecc_code[2] = ((~reg1) << 2) | 0x03; -} - -/* - * Detect and correct a 1 bit error for 256 byte block - */ -static int nand_correct_data (u_char *dat, u_char *read_ecc, u_char *calc_ecc) -{ - u_char a, b, c, d1, d2, d3, add, bit, i; - - /* Do error detection */ - d1 = calc_ecc[0] ^ read_ecc[0]; - d2 = calc_ecc[1] ^ read_ecc[1]; - d3 = calc_ecc[2] ^ read_ecc[2]; - - if ((d1 | d2 | d3) == 0) { - /* No errors */ - return 0; - } else { - a = (d1 ^ (d1 >> 1)) & 0x55; - b = (d2 ^ (d2 >> 1)) & 0x55; - c = (d3 ^ (d3 >> 1)) & 0x54; - - /* Found and will correct single bit error in the data */ - if ((a == 0x55) && (b == 0x55) && (c == 0x54)) { - c = 0x80; - add = 0; - a = 0x80; - for (i=0; i<4; i++) { - if (d1 & c) - add |= a; - c >>= 2; - a >>= 1; - } - c = 0x80; - for (i=0; i<4; i++) { - if (d2 & c) - add |= a; - c >>= 2; - a >>= 1; - } - bit = 0; - b = 0x04; - c = 0x80; - for (i=0; i<3; i++) { - if (d3 & c) - bit |= b; - c >>= 2; - b >>= 1; - } - b = 0x01; - a = dat[add]; - a ^= (b << bit); - dat[add] = a; - return 1; - } - else { - i = 0; - while (d1) { - if (d1 & 0x01) - ++i; - d1 >>= 1; - } - while (d2) { - if (d2 & 0x01) - ++i; - d2 >>= 1; - } - while (d3) { - if (d3 & 0x01) - ++i; - d3 >>= 1; - } - if (i == 1) { - /* ECC Code Error Correction */ - read_ecc[0] = calc_ecc[0]; - read_ecc[1] = calc_ecc[1]; - read_ecc[2] = calc_ecc[2]; - return 2; - } - else { - /* Uncorrectable Error */ - return -1; - } - } - } - - /* Should never happen */ - return -1; -} - -#endif - -#ifdef CONFIG_JFFS2_NAND - -int read_jffs2_nand(size_t start, size_t len, - size_t * retlen, u_char * buf, int nanddev) -{ - return nand_rw(nand_dev_desc + nanddev, NANDRW_READ | NANDRW_JFFS2, - start, len, retlen, buf); -} +U_BOOT_CMD(nboot, 4, 1, do_nandboot, + "nboot - boot from NAND device\n", "loadAddr dev\n"); -#endif /* CONFIG_JFFS2_NAND */ +#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */ -#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */ -- cgit v1.2.1 From ac7eb8a315e25863637a8d2c02af18815458b63f Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Wed, 14 Sep 2005 23:53:32 +0200 Subject: Update of new NAND code Patch by Ladislav Michl, 13 Sep 2005 --- common/cmd_jffs2.c | 19 +- common/cmd_nand.c | 2040 ++++++++++++++++++++++++++++++++++++++++++------- common/cmd_nand_new.c | 364 +++++++++ 3 files changed, 2142 insertions(+), 281 deletions(-) create mode 100644 common/cmd_nand_new.c (limited to 'common') diff --git a/common/cmd_jffs2.c b/common/cmd_jffs2.c index 7ab6e9ca7a..bc63f0c492 100644 --- a/common/cmd_jffs2.c +++ b/common/cmd_jffs2.c @@ -99,6 +99,10 @@ #include +#ifdef CONFIG_NEW_NAND_CODE +#include +#endif + /* enable/disable debugging messages */ #define DEBUG #undef DEBUG @@ -324,10 +328,9 @@ static int part_validate_nand(struct mtdids *id, struct part_info *part) { #if defined(CONFIG_JFFS2_NAND) && (CONFIG_COMMANDS & CFG_CMD_NAND) /* info for NAND chips */ - extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE]; - struct nand_chip *nand; + nand_info_t *nand; - nand = &nand_dev_desc[id->num]; + nand = &nand_info[id->num]; if ((unsigned long)(part->offset) % nand->erasesize) { printf("%s%d: partition (%s) start offset alignment incorrect\n", @@ -422,8 +425,9 @@ static int part_del(struct mtd_device *dev, struct part_info *part) } } - +#ifndef CONFIG_NEW_NAND_CODE jffs2_free_cache(part); +#endif list_del(&part->link); free(part); dev->num_parts--; @@ -445,7 +449,9 @@ static void part_delall(struct list_head *head) list_for_each_safe(entry, n, head) { part_tmp = list_entry(entry, struct part_info, link); +#ifndef CONFIG_NEW_NAND_CODE jffs2_free_cache(part_tmp); +#endif list_del(entry); free(part_tmp); } @@ -661,6 +667,7 @@ static int device_validate(u8 type, u8 num, u32 *size) if (num < CFG_MAX_FLASH_BANKS) { extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; *size = flash_info[num].size; + return 0; } @@ -672,8 +679,12 @@ static int device_validate(u8 type, u8 num, u32 *size) } else if (type == MTD_DEV_TYPE_NAND) { #if defined(CONFIG_JFFS2_NAND) && (CONFIG_COMMANDS & CFG_CMD_NAND) if (num < CFG_MAX_NAND_DEVICE) { +#ifdef CONFIG_NEW_NAND_CODE + *size = nand_info[num].size; +#else extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE]; *size = nand_dev_desc[num].totlen; +#endif return 0; } diff --git a/common/cmd_nand.c b/common/cmd_nand.c index ae4c68ac1f..0c05255855 100644 --- a/common/cmd_nand.c +++ b/common/cmd_nand.c @@ -1,15 +1,18 @@ /* - * Rick Bronson and Pantelis Antoniou + * Driver for NAND support, Rick Bronson + * borrowed heavily from: + * (c) 1999 Machine Vision Holdings, Inc. + * (c) 1999, 2000 David Woodhouse + * + * Added 16-bit nand support + * (C) 2004 Texas Instruments */ #include - -#if (CONFIG_COMMANDS & CFG_CMD_NAND) - #include -#include #include -#include +#include +#include #ifdef CONFIG_SHOW_BOOT_PROGRESS # include @@ -18,311 +21,290 @@ # define SHOW_BOOT_PROGRESS(arg) #endif -#include -#include - -extern nand_info_t nand_info[]; /* info for NAND chips */ +#if (CONFIG_COMMANDS & CFG_CMD_NAND) && !defined CONFIG_NEW_NAND_CODE -static int nand_dump_oob(nand_info_t *nand, ulong off) -{ - return 0; -} - -static int nand_dump(nand_info_t *nand, ulong off) -{ - int i; - u_char *buf, *p; - - buf = malloc(nand->oobblock + nand->oobsize); - if (!buf) { - puts("No memory for page buffer\n"); - return 1; - } - off &= ~(nand->oobblock - 1); - i = nand_read_raw(nand, buf, off, nand->oobblock, nand->oobsize); - if (i < 0) { - printf("Error (%d) reading page %08x\n", i, off); - free(buf); - return 1; - } - printf("Page %08x dump:\n", off); - i = nand->oobblock >> 4; p = buf; - while (i--) { - printf( "\t%02x %02x %02x %02x %02x %02x %02x %02x" - " %02x %02x %02x %02x %02x %02x %02x %02x\n", - p[0], p[1], p[2], p[3], p[4], p[5], p[6], p[7], - p[8], p[9], p[10], p[11], p[12], p[13], p[14], p[15]); - p += 16; - } - puts("OOB:\n"); - i = nand->oobsize >> 3; - while (i--) { - printf( "\t%02x %02x %02x %02x %02x %02x %02x %02x\n", - p[0], p[1], p[2], p[3], p[4], p[5], p[6], p[7]); - p += 8; - } - free(buf); +#include +#include +#include - return 0; -} +#ifdef CONFIG_OMAP1510 +void archflashwp(void *archdata, int wp); +#endif -/* ------------------------------------------------------------------------- */ +#define ROUND_DOWN(value,boundary) ((value) & (~((boundary)-1))) -static void -arg_off_size(int argc, char *argv[], ulong *off, ulong *size, ulong totsize) -{ - *off = 0; - *size = 0; +/* + * Definition of the out of band configuration structure + */ +struct nand_oob_config { + int ecc_pos[6]; /* position of ECC bytes inside oob */ + int badblock_pos; /* position of bad block flag inside oob -1 = inactive */ + int eccvalid_pos; /* position of ECC valid flag inside oob -1 = inactive */ +} oob_config = { {0}, 0, 0}; + +#undef NAND_DEBUG +#undef PSYCHO_DEBUG + +/* ****************** WARNING ********************* + * When ALLOW_ERASE_BAD_DEBUG is non-zero the erase command will + * erase (or at least attempt to erase) blocks that are marked + * bad. This can be very handy if you are _sure_ that the block + * is OK, say because you marked a good block bad to test bad + * block handling and you are done testing, or if you have + * accidentally marked blocks bad. + * + * Erasing factory marked bad blocks is a _bad_ idea. If the + * erase succeeds there is no reliable way to find them again, + * and attempting to program or erase bad blocks can affect + * the data in _other_ (good) blocks. + */ +#define ALLOW_ERASE_BAD_DEBUG 0 -#if defined(CONFIG_JFFS2_NAND) && defined(CFG_JFFS_CUSTOM_PART) - if (argc >= 1 && strcmp(argv[0], "partition") == 0) { - int part_num; - struct part_info *part; - const char *partstr; +#define CONFIG_MTD_NAND_ECC /* enable ECC */ +#define CONFIG_MTD_NAND_ECC_JFFS2 - if (argc >= 2) - partstr = argv[1]; - else - partstr = getenv("partition"); +/* bits for nand_rw() `cmd'; or together as needed */ +#define NANDRW_READ 0x01 +#define NANDRW_WRITE 0x00 +#define NANDRW_JFFS2 0x02 +#define NANDRW_JFFS2_SKIP 0x04 - if (partstr) - part_num = (int)simple_strtoul(partstr, NULL, 10); - else - part_num = 0; - - part = jffs2_part_info(part_num); - if (part == NULL) { - printf("\nInvalid partition %d\n", part_num); - return; - } - *size = part->size; - *off = (ulong)part->offset; - } else +/* + * Function Prototypes + */ +static void nand_print(struct nand_chip *nand); +int nand_rw (struct nand_chip* nand, int cmd, + size_t start, size_t len, + size_t * retlen, u_char * buf); +int nand_erase(struct nand_chip* nand, size_t ofs, size_t len, int clean); +static int nand_read_ecc(struct nand_chip *nand, size_t start, size_t len, + size_t * retlen, u_char *buf, u_char *ecc_code); +static int nand_write_ecc (struct nand_chip* nand, size_t to, size_t len, + size_t * retlen, const u_char * buf, u_char * ecc_code); +static void nand_print_bad(struct nand_chip *nand); +static int nand_read_oob(struct nand_chip* nand, size_t ofs, size_t len, + size_t * retlen, u_char * buf); +static int nand_write_oob(struct nand_chip* nand, size_t ofs, size_t len, + size_t * retlen, const u_char * buf); +static int NanD_WaitReady(struct nand_chip *nand, int ale_wait); +#ifdef CONFIG_MTD_NAND_ECC +static int nand_correct_data (u_char *dat, u_char *read_ecc, u_char *calc_ecc); +static void nand_calculate_ecc (const u_char *dat, u_char *ecc_code); #endif - { - if (argc >= 1) - *off = (ulong)simple_strtoul(argv[0], NULL, 16); - else - *off = 0; - if (argc >= 2) - *size = (ulong)simple_strtoul(argv[1], NULL, 16); - else - *size = totsize - *off; +struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE] = {{0}}; - } +/* Current NAND Device */ +static int curr_device = -1; -} +/* ------------------------------------------------------------------------- */ -int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) +int do_nand (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) { - int i, dev, ret; - ulong addr, off, size; - char *cmd, *s; - nand_info_t *nand; + int rcode = 0; - /* at least two arguments please */ - if (argc < 2) - goto usage; - - cmd = argv[1]; + switch (argc) { + case 0: + case 1: + printf ("Usage:\n%s\n", cmdtp->usage); + return 1; + case 2: + if (strcmp(argv[1],"info") == 0) { + int i; - if (strcmp(cmd, "info") == 0) { + putc ('\n'); - putc('\n'); - for (i = 0; i < CFG_MAX_NAND_DEVICE; i++) { - if (nand_info[i].name) - printf("Device %d: %s\n", i, nand_info[i].name); + for (i=0; i= CFG_MAX_NAND_DEVICE)) - puts("\nno devices available\n"); - else - printf("\nDevice %d: %s\n", nand_curr_device, - nand_info[nand_curr_device].name); - return 0; - } - dev = (int)simple_strtoul(argv[2], NULL, 10); - if (dev < 0 || dev >= CFG_MAX_NAND_DEVICE || !nand_info[dev].name) { - puts("No such device\n"); + } else if (strcmp(argv[1],"device") == 0) { + if ((curr_device < 0) || (curr_device >= CFG_MAX_NAND_DEVICE)) { + puts ("\nno devices available\n"); return 1; } - printf("Device %d: %s", dev, nand_info[dev].name); - puts("... is now current device\n"); - nand_curr_device = dev; + printf ("\nDevice %d: ", curr_device); + nand_print(&nand_dev_desc[curr_device]); return 0; - } - - if (strcmp(cmd, "bad") != 0 && strcmp(cmd, "erase") != 0 && - strncmp(cmd, "dump", 4) != 0 && - strncmp(cmd, "read", 4) != 0 && strncmp(cmd, "write", 5) != 0 -#ifdef CONFIG_MTD_NAND_UNSAFE - && strcmp(cmd, "scrub") != 0 && strcmp(cmd, "biterr") != 0 - && strcmp(cmd, "markbad") != 0 -#endif - ) - goto usage; - - /* the following commands operate on the current device */ - if (nand_curr_device < 0 || nand_curr_device >= CFG_MAX_NAND_DEVICE || - !nand_info[nand_curr_device].name) { - puts("\nno devices available\n"); - return 1; - } - nand = &nand_info[nand_curr_device]; - if (strcmp(cmd, "bad") == 0) { - printf("\nDevice %d bad blocks:\n", nand_curr_device); - for (off = 0; off < nand->size; off += nand->erasesize) - if (nand_block_isbad(nand, off)) - printf(" %08x\n", off); + } else if (strcmp(argv[1],"bad") == 0) { + if ((curr_device < 0) || (curr_device >= CFG_MAX_NAND_DEVICE)) { + puts ("\nno devices available\n"); + return 1; + } + printf ("\nDevice %d bad blocks:\n", curr_device); + nand_print_bad(&nand_dev_desc[curr_device]); return 0; - } - - if (strcmp(cmd, "erase") == 0 -#ifdef CONFIG_MTD_NAND_UNSAFE - || strcmp(cmd, "scrub") == 0 -#endif - ) { -#ifdef CONFIG_MTD_NAND_UNSAFE - i = strcmp(cmd, "scrub") == 0; /* 1 scrub, 0 = erase */ -#endif + } + printf ("Usage:\n%s\n", cmdtp->usage); + return 1; + case 3: + if (strcmp(argv[1],"device") == 0) { + int dev = (int)simple_strtoul(argv[2], NULL, 10); - arg_off_size(argc - 2, argv + 2, &off, &size, nand->size); - if (off == 0 && size == 0) + printf ("\nDevice %d: ", dev); + if (dev >= CFG_MAX_NAND_DEVICE) { + puts ("unknown device\n"); return 1; + } + nand_print(&nand_dev_desc[dev]); + /*nand_print (dev);*/ - printf("\nNAND %s: device %d offset 0x%x, size 0x%x ", -#ifdef CONFIG_MTD_NAND_UNSAFE - i ? "scrub" : -#endif - "erase", - nand_curr_device, off, size); + if (nand_dev_desc[dev].ChipID == NAND_ChipID_UNKNOWN) { + return 1; + } -#ifdef CONFIG_MTD_NAND_UNSAFE - if (i) - ret = nand_scrub(nand, off, size); - else -#endif - ret = nand_erase(nand, off, size); + curr_device = dev; - printf("%s\n", ret ? "ERROR" : "OK"); + puts ("... is now current device\n"); - return ret == 0 ? 0 : 1; + return 0; } + else if (strcmp(argv[1],"erase") == 0 && strcmp(argv[2], "clean") == 0) { + struct nand_chip* nand = &nand_dev_desc[curr_device]; + ulong off = 0; + ulong size = nand->totlen; + int ret; - if (strncmp(cmd, "dump", 4) == 0) { - if (argc < 3) - goto usage; + printf ("\nNAND erase: device %d offset %ld, size %ld ... ", + curr_device, off, size); - s = strchr(cmd, '.'); - off = (int)simple_strtoul(argv[2], NULL, 16); + ret = nand_erase (nand, off, size, 1); - if (s != NULL && strcmp(s, ".oob") == 0) - ret = nand_dump_oob(nand, off); - else - ret = nand_dump(nand, off); - - return ret == 0 ? 1 : 0; + printf("%s\n", ret ? "ERROR" : "OK"); + return ret; } - /* read write */ - if (strncmp(cmd, "read", 4) == 0 || strncmp(cmd, "write", 5) == 0) { - if (argc < 4) - goto usage; -/* - s = strchr(cmd, '.'); - clean = CLEAN_NONE; - if (s != NULL) { - if (strcmp(s, ".jffs2") == 0 || strcmp(s, ".e") == 0 - || strcmp(s, ".i")) - clean = CLEAN_JFFS2; - } -*/ - addr = (ulong)simple_strtoul(argv[2], NULL, 16); - - arg_off_size(argc - 3, argv + 3, &off, &size, nand->size); - if (off == 0 && size == 0) + printf ("Usage:\n%s\n", cmdtp->usage); + return 1; + default: + /* at least 4 args */ + + if (strncmp(argv[1], "read", 4) == 0 || + strncmp(argv[1], "write", 5) == 0) { + ulong addr = simple_strtoul(argv[2], NULL, 16); + ulong off = simple_strtoul(argv[3], NULL, 16); + ulong size = simple_strtoul(argv[4], NULL, 16); + int cmd = (strncmp(argv[1], "read", 4) == 0) ? + NANDRW_READ : NANDRW_WRITE; + int ret, total; + char* cmdtail = strchr(argv[1], '.'); + + if (cmdtail && !strncmp(cmdtail, ".oob", 2)) { + /* read out-of-band data */ + if (cmd & NANDRW_READ) { + ret = nand_read_oob(nand_dev_desc + curr_device, + off, size, &total, + (u_char*)addr); + } + else { + ret = nand_write_oob(nand_dev_desc + curr_device, + off, size, &total, + (u_char*)addr); + } + return ret; + } + else if (cmdtail && !strncmp(cmdtail, ".jffs2", 2)) + cmd |= NANDRW_JFFS2; /* skip bad blocks */ + else if (cmdtail && !strncmp(cmdtail, ".jffs2s", 2)) { + cmd |= NANDRW_JFFS2; /* skip bad blocks (on read too) */ + if (cmd & NANDRW_READ) + cmd |= NANDRW_JFFS2_SKIP; /* skip bad blocks (on read too) */ + } +#ifdef SXNI855T + /* need ".e" same as ".j" for compatibility with older units */ + else if (cmdtail && !strcmp(cmdtail, ".e")) + cmd |= NANDRW_JFFS2; /* skip bad blocks */ +#endif +#ifdef CFG_NAND_SKIP_BAD_DOT_I + /* need ".i" same as ".jffs2s" for compatibility with older units (esd) */ + /* ".i" for image -> read skips bad block (no 0xff) */ + else if (cmdtail && !strcmp(cmdtail, ".i")) { + cmd |= NANDRW_JFFS2; /* skip bad blocks (on read too) */ + if (cmd & NANDRW_READ) + cmd |= NANDRW_JFFS2_SKIP; /* skip bad blocks (on read too) */ + } +#endif /* CFG_NAND_SKIP_BAD_DOT_I */ + else if (cmdtail) { + printf ("Usage:\n%s\n", cmdtp->usage); return 1; + } - i = strncmp(cmd, "read", 4) == 0; /* 1 = read, 0 = write */ - printf("\nNAND %s: device %d offset %u, size %u ... ", - i ? "read" : "write", nand_curr_device, off, size); + printf ("\nNAND %s: device %d offset %ld, size %ld ... ", + (cmd & NANDRW_READ) ? "read" : "write", + curr_device, off, size); - if (i) - ret = nand_read(nand, off, &size, (u_char *)addr); - else - ret = nand_write(nand, off, &size, (u_char *)addr); + ret = nand_rw(nand_dev_desc + curr_device, cmd, off, size, + &total, (u_char*)addr); - printf(" %d bytes %s: %s\n", size, - i ? "read" : "written", ret ? "ERROR" : "OK"); + printf (" %d bytes %s: %s\n", total, + (cmd & NANDRW_READ) ? "read" : "written", + ret ? "ERROR" : "OK"); - return ret == 0 ? 0 : 1; - } -#ifdef CONFIG_MTD_NAND_UNSAFE - if (strcmp(cmd, "markbad") == 0 || strcmp(cmd, "biterr") == 0) { - if (argc < 3) - goto usage; + return ret; + } else if (strcmp(argv[1],"erase") == 0 && + (argc == 4 || strcmp("clean", argv[2]) == 0)) { + int clean = argc == 5; + ulong off = simple_strtoul(argv[2 + clean], NULL, 16); + ulong size = simple_strtoul(argv[3 + clean], NULL, 16); + int ret; - i = strcmp(cmd, "biterr") == 0; + printf ("\nNAND erase: device %d offset %ld, size %ld ... ", + curr_device, off, size); - off = (int)simple_strtoul(argv[2], NULL, 16); + ret = nand_erase (nand_dev_desc + curr_device, off, size, clean); - if (i) - ret = nand_make_bit_error(nand, off); - else - ret = nand_mark_bad(nand, off); + printf("%s\n", ret ? "ERROR" : "OK"); - return ret == 0 ? 0 : 1; + return ret; + } else { + printf ("Usage:\n%s\n", cmdtp->usage); + rcode = 1; } -#endif -usage: - printf("Usage:\n%s\n", cmdtp->usage); - return 1; + return rcode; + } } -U_BOOT_CMD(nand, 5, 1, do_nand, +U_BOOT_CMD( + nand, 5, 1, do_nand, "nand - NAND sub-system\n", - "info - show available NAND devices\n" - "nand device [dev] - show or set current device\n" - "nand read[.jffs2] - addr off size\n" - "nand write[.jffs2] - addr off size - read/write `size' bytes starting\n" + "info - show available NAND devices\n" + "nand device [dev] - show or set current device\n" + "nand read[.jffs2[s]] addr off size\n" + "nand write[.jffs2] addr off size - read/write `size' bytes starting\n" " at offset `off' to/from memory address `addr'\n" "nand erase [clean] [off size] - erase `size' bytes from\n" " offset `off' (entire device if not specified)\n" "nand bad - show bad blocks\n" - "nand dump[.oob] off - dump page\n" - "nand scrub - really clean NAND erasing bad blocks (UNSAFE)\n" - "nand markbad off - mark bad block at offset (UNSAFE)\n" - "nand biterr off - make a bit error at offset (UNSAFE)\n"); + "nand read.oob addr off size - read out-of-band data\n" + "nand write.oob addr off size - read out-of-band data\n" +); -int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) +int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) { char *boot_device = NULL; char *ep; int dev; - int r; - ulong addr, cnt, offset = 0; + ulong cnt; + ulong addr; + ulong offset = 0; image_header_t *hdr; - nand_info_t *nand; - + int rcode = 0; switch (argc) { case 1: addr = CFG_LOAD_ADDR; - boot_device = getenv("bootdevice"); + boot_device = getenv ("bootdevice"); break; case 2: addr = simple_strtoul(argv[1], NULL, 16); - boot_device = getenv("bootdevice"); + boot_device = getenv ("bootdevice"); break; case 3: addr = simple_strtoul(argv[1], NULL, 16); @@ -334,53 +316,55 @@ int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) offset = simple_strtoul(argv[3], NULL, 16); break; default: - printf("Usage:\n%s\n", cmdtp->usage); - SHOW_BOOT_PROGRESS(-1); + printf ("Usage:\n%s\n", cmdtp->usage); + SHOW_BOOT_PROGRESS (-1); return 1; } if (!boot_device) { - puts("\n** No boot device **\n"); - SHOW_BOOT_PROGRESS(-1); + puts ("\n** No boot device **\n"); + SHOW_BOOT_PROGRESS (-1); return 1; } dev = simple_strtoul(boot_device, &ep, 16); - if (dev < 0 || dev >= CFG_MAX_NAND_DEVICE || !nand_info[dev].name) { - printf("\n** Device %d not available\n", dev); - SHOW_BOOT_PROGRESS(-1); + if ((dev >= CFG_MAX_NAND_DEVICE) || + (nand_dev_desc[dev].ChipID == NAND_ChipID_UNKNOWN)) { + printf ("\n** Device %d not available\n", dev); + SHOW_BOOT_PROGRESS (-1); return 1; } - nand = &nand_info[dev]; - printf("\nLoading from device %d: %s (offset 0x%lx)\n", - dev, nand->name, offset); + printf ("\nLoading from device %d: %s at 0x%lx (offset 0x%lx)\n", + dev, nand_dev_desc[dev].name, nand_dev_desc[dev].IO_ADDR, + offset); - cnt = nand->oobblock; - r = nand_read(nand, offset, &cnt, (u_char *) addr); - if (r) { - printf("** Read error on %d\n", dev); - SHOW_BOOT_PROGRESS(-1); + if (nand_rw (nand_dev_desc + dev, NANDRW_READ, offset, + SECTORSIZE, NULL, (u_char *)addr)) { + printf ("** Read error on %d\n", dev); + SHOW_BOOT_PROGRESS (-1); return 1; } - hdr = (image_header_t *) addr; + hdr = (image_header_t *)addr; - if (ntohl(hdr->ih_magic) != IH_MAGIC) { - printf("\n** Bad Magic Number 0x%x **\n", hdr->ih_magic); - SHOW_BOOT_PROGRESS(-1); - return 1; - } + if (ntohl(hdr->ih_magic) == IH_MAGIC) { - print_image_hdr(hdr); + print_image_hdr (hdr); - cnt = (ntohl(hdr->ih_size) + sizeof (image_header_t)); + cnt = (ntohl(hdr->ih_size) + sizeof(image_header_t)); + cnt -= SECTORSIZE; + } else { + printf ("\n** Bad Magic Number 0x%x **\n", hdr->ih_magic); + SHOW_BOOT_PROGRESS (-1); + return 1; + } - r = nand_read(nand, offset, &cnt, (u_char *) addr); - if (r) { - printf("** Read error on %d\n", dev); - SHOW_BOOT_PROGRESS(-1); + if (nand_rw (nand_dev_desc + dev, NANDRW_READ, offset + SECTORSIZE, cnt, + NULL, (u_char *)(addr+SECTORSIZE))) { + printf ("** Read error on %d\n", dev); + SHOW_BOOT_PROGRESS (-1); return 1; } @@ -389,24 +373,1526 @@ int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) load_addr = addr; /* Check if we should attempt an auto-start */ - if (((ep = getenv("autostart")) != NULL) && (strcmp(ep, "yes") == 0)) { + if (((ep = getenv("autostart")) != NULL) && (strcmp(ep,"yes") == 0)) { char *local_args[2]; - extern int do_bootm(cmd_tbl_t *, int, int, char *[]); + extern int do_bootm (cmd_tbl_t *, int, int, char *[]); local_args[0] = argv[0]; local_args[1] = NULL; - printf("Automatic boot of image at addr 0x%08lx ...\n", addr); + printf ("Automatic boot of image at addr 0x%08lx ...\n", addr); + + do_bootm (cmdtp, 0, 1, local_args); + rcode = 1; + } + return rcode; +} + +U_BOOT_CMD( + nboot, 4, 1, do_nandboot, + "nboot - boot from NAND device\n", + "loadAddr dev\n" +); - do_bootm(cmdtp, 0, 1, local_args); +/* returns 0 if block containing pos is OK: + * valid erase block and + * not marked bad, or no bad mark position is specified + * returns 1 if marked bad or otherwise invalid + */ +int check_block (struct nand_chip *nand, unsigned long pos) +{ + int retlen; + uint8_t oob_data; + uint16_t oob_data16[6]; + int page0 = pos & (-nand->erasesize); + int page1 = page0 + nand->oobblock; + int badpos = oob_config.badblock_pos; + + if (pos >= nand->totlen) return 1; + + if (badpos < 0) + return 0; /* no way to check, assume OK */ + + if (nand->bus16) { + if (nand_read_oob(nand, (page0 + 0), 12, &retlen, (uint8_t *)oob_data16) + || (oob_data16[2] & 0xff00) != 0xff00) + return 1; + if (nand_read_oob(nand, (page1 + 0), 12, &retlen, (uint8_t *)oob_data16) + || (oob_data16[2] & 0xff00) != 0xff00) + return 1; + } else { + /* Note - bad block marker can be on first or second page */ + if (nand_read_oob(nand, page0 + badpos, 1, &retlen, &oob_data) + || oob_data != 0xff + || nand_read_oob (nand, page1 + badpos, 1, &retlen, &oob_data) + || oob_data != 0xff) + return 1; } + return 0; } -U_BOOT_CMD(nboot, 4, 1, do_nandboot, - "nboot - boot from NAND device\n", "loadAddr dev\n"); +/* print bad blocks in NAND flash */ +static void nand_print_bad(struct nand_chip* nand) +{ + unsigned long pos; + + for (pos = 0; pos < nand->totlen; pos += nand->erasesize) { + if (check_block(nand, pos)) + printf(" 0x%8.8lx\n", pos); + } + puts("\n"); +} + +/* cmd: 0: NANDRW_WRITE write, fail on bad block + * 1: NANDRW_READ read, fail on bad block + * 2: NANDRW_WRITE | NANDRW_JFFS2 write, skip bad blocks + * 3: NANDRW_READ | NANDRW_JFFS2 read, data all 0xff for bad blocks + * 7: NANDRW_READ | NANDRW_JFFS2 | NANDRW_JFFS2_SKIP read, skip bad blocks + */ +int nand_rw (struct nand_chip* nand, int cmd, + size_t start, size_t len, + size_t * retlen, u_char * buf) +{ + int ret = 0, n, total = 0; + char eccbuf[6]; + /* eblk (once set) is the start of the erase block containing the + * data being processed. + */ + unsigned long eblk = ~0; /* force mismatch on first pass */ + unsigned long erasesize = nand->erasesize; + + while (len) { + if ((start & (-erasesize)) != eblk) { + /* have crossed into new erase block, deal with + * it if it is sure marked bad. + */ + eblk = start & (-erasesize); /* start of block */ + if (check_block(nand, eblk)) { + if (cmd == (NANDRW_READ | NANDRW_JFFS2)) { + while (len > 0 && + start - eblk < erasesize) { + *(buf++) = 0xff; + ++start; + ++total; + --len; + } + continue; + } else if (cmd == (NANDRW_READ | NANDRW_JFFS2 | NANDRW_JFFS2_SKIP)) { + start += erasesize; + continue; + } else if (cmd == (NANDRW_WRITE | NANDRW_JFFS2)) { + /* skip bad block */ + start += erasesize; + continue; + } else { + ret = 1; + break; + } + } + } + /* The ECC will not be calculated correctly if + less than 512 is written or read */ + /* Is request at least 512 bytes AND it starts on a proper boundry */ + if((start != ROUND_DOWN(start, 0x200)) || (len < 0x200)) + printf("Warning block writes should be at least 512 bytes and start on a 512 byte boundry\n"); + + if (cmd & NANDRW_READ) { + ret = nand_read_ecc(nand, start, + min(len, eblk + erasesize - start), + &n, (u_char*)buf, eccbuf); + } else { + ret = nand_write_ecc(nand, start, + min(len, eblk + erasesize - start), + &n, (u_char*)buf, eccbuf); + } + + if (ret) + break; + + start += n; + buf += n; + total += n; + len -= n; + } + if (retlen) + *retlen = total; + + return ret; +} + +static void nand_print(struct nand_chip *nand) +{ + if (nand->numchips > 1) { + printf("%s at 0x%lx,\n" + "\t %d chips %s, size %d MB, \n" + "\t total size %ld MB, sector size %ld kB\n", + nand->name, nand->IO_ADDR, nand->numchips, + nand->chips_name, 1 << (nand->chipshift - 20), + nand->totlen >> 20, nand->erasesize >> 10); + } + else { + printf("%s at 0x%lx (", nand->chips_name, nand->IO_ADDR); + print_size(nand->totlen, ", "); + print_size(nand->erasesize, " sector)\n"); + } +} + +/* ------------------------------------------------------------------------- */ + +static int NanD_WaitReady(struct nand_chip *nand, int ale_wait) +{ + /* This is inline, to optimise the common case, where it's ready instantly */ + int ret = 0; + +#ifdef NAND_NO_RB /* in config file, shorter delays currently wrap accesses */ + if(ale_wait) + NAND_WAIT_READY(nand); /* do the worst case 25us wait */ + else + udelay(10); +#else /* has functional r/b signal */ + NAND_WAIT_READY(nand); +#endif + return ret; +} + +/* NanD_Command: Send a flash command to the flash chip */ + +static inline int NanD_Command(struct nand_chip *nand, unsigned char command) +{ + unsigned long nandptr = nand->IO_ADDR; + + /* Assert the CLE (Command Latch Enable) line to the flash chip */ + NAND_CTL_SETCLE(nandptr); + + /* Send the command */ + WRITE_NAND_COMMAND(command, nandptr); + + /* Lower the CLE line */ + NAND_CTL_CLRCLE(nandptr); + +#ifdef NAND_NO_RB + if(command == NAND_CMD_RESET){ + u_char ret_val; + NanD_Command(nand, NAND_CMD_STATUS); + do { + ret_val = READ_NAND(nandptr);/* wait till ready */ + } while((ret_val & 0x40) != 0x40); + } +#endif + return NanD_WaitReady(nand, 0); +} + +/* NanD_Address: Set the current address for the flash chip */ + +static int NanD_Address(struct nand_chip *nand, int numbytes, unsigned long ofs) +{ + unsigned long nandptr; + int i; + + nandptr = nand->IO_ADDR; + + /* Assert the ALE (Address Latch Enable) line to the flash chip */ + NAND_CTL_SETALE(nandptr); + + /* Send the address */ + /* Devices with 256-byte page are addressed as: + * Column (bits 0-7), Page (bits 8-15, 16-23, 24-31) + * there is no device on the market with page256 + * and more than 24 bits. + * Devices with 512-byte page are addressed as: + * Column (bits 0-7), Page (bits 9-16, 17-24, 25-31) + * 25-31 is sent only if the chip support it. + * bit 8 changes the read command to be sent + * (NAND_CMD_READ0 or NAND_CMD_READ1). + */ + + if (numbytes == ADDR_COLUMN || numbytes == ADDR_COLUMN_PAGE) + WRITE_NAND_ADDRESS(ofs, nandptr); + + ofs = ofs >> nand->page_shift; + + if (numbytes == ADDR_PAGE || numbytes == ADDR_COLUMN_PAGE) { + for (i = 0; i < nand->pageadrlen; i++, ofs = ofs >> 8) { + WRITE_NAND_ADDRESS(ofs, nandptr); + } + } + + /* Lower the ALE line */ + NAND_CTL_CLRALE(nandptr); + + /* Wait for the chip to respond */ + return NanD_WaitReady(nand, 1); +} + +/* NanD_SelectChip: Select a given flash chip within the current floor */ + +static inline int NanD_SelectChip(struct nand_chip *nand, int chip) +{ + /* Wait for it to be ready */ + return NanD_WaitReady(nand, 0); +} + +/* NanD_IdentChip: Identify a given NAND chip given {floor,chip} */ + +static int NanD_IdentChip(struct nand_chip *nand, int floor, int chip) +{ + int mfr, id, i; + + NAND_ENABLE_CE(nand); /* set pin low */ + /* Reset the chip */ + if (NanD_Command(nand, NAND_CMD_RESET)) { +#ifdef NAND_DEBUG + printf("NanD_Command (reset) for %d,%d returned true\n", + floor, chip); +#endif + NAND_DISABLE_CE(nand); /* set pin high */ + return 0; + } + + /* Read the NAND chip ID: 1. Send ReadID command */ + if (NanD_Command(nand, NAND_CMD_READID)) { +#ifdef NAND_DEBUG + printf("NanD_Command (ReadID) for %d,%d returned true\n", + floor, chip); +#endif + NAND_DISABLE_CE(nand); /* set pin high */ + return 0; + } + + /* Read the NAND chip ID: 2. Send address byte zero */ + NanD_Address(nand, ADDR_COLUMN, 0); + + /* Read the manufacturer and device id codes from the device */ + + mfr = READ_NAND(nand->IO_ADDR); + + id = READ_NAND(nand->IO_ADDR); + + NAND_DISABLE_CE(nand); /* set pin high */ + +#ifdef NAND_DEBUG + printf("NanD_Command (ReadID) got %x %x\n", mfr, id); +#endif + if (mfr == 0xff || mfr == 0) { + /* No response - return failure */ + return 0; + } + + /* Check it's the same as the first chip we identified. + * M-Systems say that any given nand_chip device should only + * contain _one_ type of flash part, although that's not a + * hardware restriction. */ + if (nand->mfr) { + if (nand->mfr == mfr && nand->id == id) { + return 1; /* This is another the same the first */ + } else { + printf("Flash chip at floor %d, chip %d is different:\n", + floor, chip); + } + } + + /* Print and store the manufacturer and ID codes. */ + for (i = 0; nand_flash_ids[i].name != NULL; i++) { + if (mfr == nand_flash_ids[i].manufacture_id && + id == nand_flash_ids[i].model_id) { +#ifdef NAND_DEBUG + printf("Flash chip found:\n\t Manufacturer ID: 0x%2.2X, " + "Chip ID: 0x%2.2X (%s)\n", mfr, id, + nand_flash_ids[i].name); +#endif + if (!nand->mfr) { + nand->mfr = mfr; + nand->id = id; + nand->chipshift = + nand_flash_ids[i].chipshift; + nand->page256 = nand_flash_ids[i].page256; + nand->eccsize = 256; + if (nand->page256) { + nand->oobblock = 256; + nand->oobsize = 8; + nand->page_shift = 8; + } else { + nand->oobblock = 512; + nand->oobsize = 16; + nand->page_shift = 9; + } + nand->pageadrlen = nand_flash_ids[i].pageadrlen; + nand->erasesize = nand_flash_ids[i].erasesize; + nand->chips_name = nand_flash_ids[i].name; + nand->bus16 = nand_flash_ids[i].bus16; + return 1; + } + return 0; + } + } + + +#ifdef NAND_DEBUG + /* We haven't fully identified the chip. Print as much as we know. */ + printf("Unknown flash chip found: %2.2X %2.2X\n", + id, mfr); +#endif + + return 0; +} + +/* NanD_ScanChips: Find all NAND chips present in a nand_chip, and identify them */ + +static void NanD_ScanChips(struct nand_chip *nand) +{ + int floor, chip; + int numchips[NAND_MAX_FLOORS]; + int maxchips = NAND_MAX_CHIPS; + int ret = 1; + + nand->numchips = 0; + nand->mfr = 0; + nand->id = 0; + + + /* For each floor, find the number of valid chips it contains */ + for (floor = 0; floor < NAND_MAX_FLOORS; floor++) { + ret = 1; + numchips[floor] = 0; + for (chip = 0; chip < maxchips && ret != 0; chip++) { + + ret = NanD_IdentChip(nand, floor, chip); + if (ret) { + numchips[floor]++; + nand->numchips++; + } + } + } + + /* If there are none at all that we recognise, bail */ + if (!nand->numchips) { +#ifdef NAND_DEBUG + puts ("No NAND flash chips recognised.\n"); +#endif + return; + } + + /* Allocate an array to hold the information for each chip */ + nand->chips = malloc(sizeof(struct Nand) * nand->numchips); + if (!nand->chips) { + puts ("No memory for allocating chip info structures\n"); + return; + } + + ret = 0; + + /* Fill out the chip array with {floor, chipno} for each + * detected chip in the device. */ + for (floor = 0; floor < NAND_MAX_FLOORS; floor++) { + for (chip = 0; chip < numchips[floor]; chip++) { + nand->chips[ret].floor = floor; + nand->chips[ret].chip = chip; + nand->chips[ret].curadr = 0; + nand->chips[ret].curmode = 0x50; + ret++; + } + } + + /* Calculate and print the total size of the device */ + nand->totlen = nand->numchips * (1 << nand->chipshift); + +#ifdef NAND_DEBUG + printf("%d flash chips found. Total nand_chip size: %ld MB\n", + nand->numchips, nand->totlen >> 20); +#endif +} + +/* we need to be fast here, 1 us per read translates to 1 second per meg */ +static void NanD_ReadBuf (struct nand_chip *nand, u_char * data_buf, int cntr) +{ + unsigned long nandptr = nand->IO_ADDR; + + NanD_Command (nand, NAND_CMD_READ0); + + if (nand->bus16) { + u16 val; + + while (cntr >= 16) { + val = READ_NAND (nandptr); + *data_buf++ = val & 0xff; + *data_buf++ = val >> 8; + val = READ_NAND (nandptr); + *data_buf++ = val & 0xff; + *data_buf++ = val >> 8; + val = READ_NAND (nandptr); + *data_buf++ = val & 0xff; + *data_buf++ = val >> 8; + val = READ_NAND (nandptr); + *data_buf++ = val & 0xff; + *data_buf++ = val >> 8; + val = READ_NAND (nandptr); + *data_buf++ = val & 0xff; + *data_buf++ = val >> 8; + val = READ_NAND (nandptr); + *data_buf++ = val & 0xff; + *data_buf++ = val >> 8; + val = READ_NAND (nandptr); + *data_buf++ = val & 0xff; + *data_buf++ = val >> 8; + val = READ_NAND (nandptr); + *data_buf++ = val & 0xff; + *data_buf++ = val >> 8; + cntr -= 16; + } + + while (cntr > 0) { + val = READ_NAND (nandptr); + *data_buf++ = val & 0xff; + *data_buf++ = val >> 8; + cntr -= 2; + } + } else { + while (cntr >= 16) { + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + *data_buf++ = READ_NAND (nandptr); + cntr -= 16; + } + + while (cntr > 0) { + *data_buf++ = READ_NAND (nandptr); + cntr--; + } + } +} + +/* + * NAND read with ECC + */ +static int nand_read_ecc(struct nand_chip *nand, size_t start, size_t len, + size_t * retlen, u_char *buf, u_char *ecc_code) +{ + int col, page; + int ecc_status = 0; +#ifdef CONFIG_MTD_NAND_ECC + int j; + int ecc_failed = 0; + u_char *data_poi; + u_char ecc_calc[6]; +#endif + + /* Do not allow reads past end of device */ + if ((start + len) > nand->totlen) { + printf ("%s: Attempt read beyond end of device %x %x %x\n", + __FUNCTION__, (uint) start, (uint) len, (uint) nand->totlen); + *retlen = 0; + return -1; + } + + /* First we calculate the starting page */ + /*page = shr(start, nand->page_shift);*/ + page = start >> nand->page_shift; + + /* Get raw starting column */ + col = start & (nand->oobblock - 1); + + /* Initialize return value */ + *retlen = 0; + + /* Select the NAND device */ + NAND_ENABLE_CE(nand); /* set pin low */ + + /* Loop until all data read */ + while (*retlen < len) { + +#ifdef CONFIG_MTD_NAND_ECC + /* Do we have this page in cache ? */ + if (nand->cache_page == page) + goto readdata; + /* Send the read command */ + NanD_Command(nand, NAND_CMD_READ0); + if (nand->bus16) { + NanD_Address(nand, ADDR_COLUMN_PAGE, + (page << nand->page_shift) + (col >> 1)); + } else { + NanD_Address(nand, ADDR_COLUMN_PAGE, + (page << nand->page_shift) + col); + } + + /* Read in a page + oob data */ + NanD_ReadBuf(nand, nand->data_buf, nand->oobblock + nand->oobsize); + + /* copy data into cache, for read out of cache and if ecc fails */ + if (nand->data_cache) { + memcpy (nand->data_cache, nand->data_buf, + nand->oobblock + nand->oobsize); + } + + /* Pick the ECC bytes out of the oob data */ + for (j = 0; j < 6; j++) { + ecc_code[j] = nand->data_buf[(nand->oobblock + oob_config.ecc_pos[j])]; + } + + /* Calculate the ECC and verify it */ + /* If block was not written with ECC, skip ECC */ + if (oob_config.eccvalid_pos != -1 && + (nand->data_buf[nand->oobblock + oob_config.eccvalid_pos] & 0x0f) != 0x0f) { + + nand_calculate_ecc (&nand->data_buf[0], &ecc_calc[0]); + switch (nand_correct_data (&nand->data_buf[0], &ecc_code[0], &ecc_calc[0])) { + case -1: + printf ("%s: Failed ECC read, page 0x%08x\n", __FUNCTION__, page); + ecc_failed++; + break; + case 1: + case 2: /* transfer ECC corrected data to cache */ + if (nand->data_cache) + memcpy (nand->data_cache, nand->data_buf, 256); + break; + } + } + + if (oob_config.eccvalid_pos != -1 && + nand->oobblock == 512 && (nand->data_buf[nand->oobblock + oob_config.eccvalid_pos] & 0xf0) != 0xf0) { + + nand_calculate_ecc (&nand->data_buf[256], &ecc_calc[3]); + switch (nand_correct_data (&nand->data_buf[256], &ecc_code[3], &ecc_calc[3])) { + case -1: + printf ("%s: Failed ECC read, page 0x%08x\n", __FUNCTION__, page); + ecc_failed++; + break; + case 1: + case 2: /* transfer ECC corrected data to cache */ + if (nand->data_cache) + memcpy (&nand->data_cache[256], &nand->data_buf[256], 256); + break; + } + } +readdata: + /* Read the data from ECC data buffer into return buffer */ + data_poi = (nand->data_cache) ? nand->data_cache : nand->data_buf; + data_poi += col; + if ((*retlen + (nand->oobblock - col)) >= len) { + memcpy (buf + *retlen, data_poi, len - *retlen); + *retlen = len; + } else { + memcpy (buf + *retlen, data_poi, nand->oobblock - col); + *retlen += nand->oobblock - col; + } + /* Set cache page address, invalidate, if ecc_failed */ + nand->cache_page = (nand->data_cache && !ecc_failed) ? page : -1; + + ecc_status += ecc_failed; + ecc_failed = 0; + +#else + /* Send the read command */ + NanD_Command(nand, NAND_CMD_READ0); + if (nand->bus16) { + NanD_Address(nand, ADDR_COLUMN_PAGE, + (page << nand->page_shift) + (col >> 1)); + } else { + NanD_Address(nand, ADDR_COLUMN_PAGE, + (page << nand->page_shift) + col); + } + + /* Read the data directly into the return buffer */ + if ((*retlen + (nand->oobblock - col)) >= len) { + NanD_ReadBuf(nand, buf + *retlen, len - *retlen); + *retlen = len; + /* We're done */ + continue; + } else { + NanD_ReadBuf(nand, buf + *retlen, nand->oobblock - col); + *retlen += nand->oobblock - col; + } +#endif + /* For subsequent reads align to page boundary. */ + col = 0; + /* Increment page address */ + page++; + } + + /* De-select the NAND device */ + NAND_DISABLE_CE(nand); /* set pin high */ + + /* + * Return success, if no ECC failures, else -EIO + * fs driver will take care of that, because + * retlen == desired len and result == -EIO + */ + return ecc_status ? -1 : 0; +} + +/* + * Nand_page_program function is used for write and writev ! + */ +static int nand_write_page (struct nand_chip *nand, + int page, int col, int last, u_char * ecc_code) +{ + + int i; + unsigned long nandptr = nand->IO_ADDR; + +#ifdef CONFIG_MTD_NAND_ECC +#ifdef CONFIG_MTD_NAND_VERIFY_WRITE + int ecc_bytes = (nand->oobblock == 512) ? 6 : 3; +#endif +#endif + /* pad oob area */ + for (i = nand->oobblock; i < nand->oobblock + nand->oobsize; i++) + nand->data_buf[i] = 0xff; + +#ifdef CONFIG_MTD_NAND_ECC + /* Zero out the ECC array */ + for (i = 0; i < 6; i++) + ecc_code[i] = 0x00; + + /* Read back previous written data, if col > 0 */ + if (col) { + NanD_Command (nand, NAND_CMD_READ0); + if (nand->bus16) { + NanD_Address (nand, ADDR_COLUMN_PAGE, + (page << nand->page_shift) + (col >> 1)); + } else { + NanD_Address (nand, ADDR_COLUMN_PAGE, + (page << nand->page_shift) + col); + } + + if (nand->bus16) { + u16 val; + + for (i = 0; i < col; i += 2) { + val = READ_NAND (nandptr); + nand->data_buf[i] = val & 0xff; + nand->data_buf[i + 1] = val >> 8; + } + } else { + for (i = 0; i < col; i++) + nand->data_buf[i] = READ_NAND (nandptr); + } + } + + /* Calculate and write the ECC if we have enough data */ + if ((col < nand->eccsize) && (last >= nand->eccsize)) { + nand_calculate_ecc (&nand->data_buf[0], &(ecc_code[0])); + for (i = 0; i < 3; i++) { + nand->data_buf[(nand->oobblock + + oob_config.ecc_pos[i])] = ecc_code[i]; + } + if (oob_config.eccvalid_pos != -1) { + nand->data_buf[nand->oobblock + + oob_config.eccvalid_pos] = 0xf0; + } + } + + /* Calculate and write the second ECC if we have enough data */ + if ((nand->oobblock == 512) && (last == nand->oobblock)) { + nand_calculate_ecc (&nand->data_buf[256], &(ecc_code[3])); + for (i = 3; i < 6; i++) { + nand->data_buf[(nand->oobblock + + oob_config.ecc_pos[i])] = ecc_code[i]; + } + if (oob_config.eccvalid_pos != -1) { + nand->data_buf[nand->oobblock + + oob_config.eccvalid_pos] &= 0x0f; + } + } +#endif + /* Prepad for partial page programming !!! */ + for (i = 0; i < col; i++) + nand->data_buf[i] = 0xff; + + /* Postpad for partial page programming !!! oob is already padded */ + for (i = last; i < nand->oobblock; i++) + nand->data_buf[i] = 0xff; + + /* Send command to begin auto page programming */ + NanD_Command (nand, NAND_CMD_READ0); + NanD_Command (nand, NAND_CMD_SEQIN); + if (nand->bus16) { + NanD_Address (nand, ADDR_COLUMN_PAGE, + (page << nand->page_shift) + (col >> 1)); + } else { + NanD_Address (nand, ADDR_COLUMN_PAGE, + (page << nand->page_shift) + col); + } + + /* Write out complete page of data */ + if (nand->bus16) { + for (i = 0; i < (nand->oobblock + nand->oobsize); i += 2) { + WRITE_NAND (nand->data_buf[i] + + (nand->data_buf[i + 1] << 8), + nand->IO_ADDR); + } + } else { + for (i = 0; i < (nand->oobblock + nand->oobsize); i++) + WRITE_NAND (nand->data_buf[i], nand->IO_ADDR); + } + + /* Send command to actually program the data */ + NanD_Command (nand, NAND_CMD_PAGEPROG); + NanD_Command (nand, NAND_CMD_STATUS); +#ifdef NAND_NO_RB + { + u_char ret_val; + + do { + ret_val = READ_NAND (nandptr); /* wait till ready */ + } while ((ret_val & 0x40) != 0x40); + } +#endif + /* See if device thinks it succeeded */ + if (READ_NAND (nand->IO_ADDR) & 0x01) { + printf ("%s: Failed write, page 0x%08x, ", __FUNCTION__, + page); + return -1; + } +#ifdef CONFIG_MTD_NAND_VERIFY_WRITE + /* + * The NAND device assumes that it is always writing to + * a cleanly erased page. Hence, it performs its internal + * write verification only on bits that transitioned from + * 1 to 0. The device does NOT verify the whole page on a + * byte by byte basis. It is possible that the page was + * not completely erased or the page is becoming unusable + * due to wear. The read with ECC would catch the error + * later when the ECC page check fails, but we would rather + * catch it early in the page write stage. Better to write + * no data than invalid data. + */ + + /* Send command to read back the page */ + if (col < nand->eccsize) + NanD_Command (nand, NAND_CMD_READ0); + else + NanD_Command (nand, NAND_CMD_READ1); + if (nand->bus16) { + NanD_Address (nand, ADDR_COLUMN_PAGE, + (page << nand->page_shift) + (col >> 1)); + } else { + NanD_Address (nand, ADDR_COLUMN_PAGE, + (page << nand->page_shift) + col); + } + + /* Loop through and verify the data */ + if (nand->bus16) { + for (i = col; i < last; i = +2) { + if ((nand->data_buf[i] + + (nand->data_buf[i + 1] << 8)) != READ_NAND (nand->IO_ADDR)) { + printf ("%s: Failed write verify, page 0x%08x ", + __FUNCTION__, page); + return -1; + } + } + } else { + for (i = col; i < last; i++) { + if (nand->data_buf[i] != READ_NAND (nand->IO_ADDR)) { + printf ("%s: Failed write verify, page 0x%08x ", + __FUNCTION__, page); + return -1; + } + } + } + +#ifdef CONFIG_MTD_NAND_ECC + /* + * We also want to check that the ECC bytes wrote + * correctly for the same reasons stated above. + */ + NanD_Command (nand, NAND_CMD_READOOB); + if (nand->bus16) { + NanD_Address (nand, ADDR_COLUMN_PAGE, + (page << nand->page_shift) + (col >> 1)); + } else { + NanD_Address (nand, ADDR_COLUMN_PAGE, + (page << nand->page_shift) + col); + } + if (nand->bus16) { + for (i = 0; i < nand->oobsize; i += 2) { + u16 val; + + val = READ_NAND (nand->IO_ADDR); + nand->data_buf[i] = val & 0xff; + nand->data_buf[i + 1] = val >> 8; + } + } else { + for (i = 0; i < nand->oobsize; i++) { + nand->data_buf[i] = READ_NAND (nand->IO_ADDR); + } + } + for (i = 0; i < ecc_bytes; i++) { + if ((nand->data_buf[(oob_config.ecc_pos[i])] != ecc_code[i]) && ecc_code[i]) { + printf ("%s: Failed ECC write " + "verify, page 0x%08x, " + "%6i bytes were succesful\n", + __FUNCTION__, page, i); + return -1; + } + } +#endif /* CONFIG_MTD_NAND_ECC */ +#endif /* CONFIG_MTD_NAND_VERIFY_WRITE */ + return 0; +} + +static int nand_write_ecc (struct nand_chip* nand, size_t to, size_t len, + size_t * retlen, const u_char * buf, u_char * ecc_code) +{ + int i, page, col, cnt, ret = 0; + + /* Do not allow write past end of device */ + if ((to + len) > nand->totlen) { + printf ("%s: Attempt to write past end of page\n", __FUNCTION__); + return -1; + } + + /* Shift to get page */ + page = ((int) to) >> nand->page_shift; + + /* Get the starting column */ + col = to & (nand->oobblock - 1); + + /* Initialize return length value */ + *retlen = 0; + + /* Select the NAND device */ +#ifdef CONFIG_OMAP1510 + archflashwp(0,0); +#endif +#ifdef CFG_NAND_WP + NAND_WP_OFF(); +#endif + + NAND_ENABLE_CE(nand); /* set pin low */ + + /* Check the WP bit */ + NanD_Command(nand, NAND_CMD_STATUS); + if (!(READ_NAND(nand->IO_ADDR) & 0x80)) { + printf ("%s: Device is write protected!!!\n", __FUNCTION__); + ret = -1; + goto out; + } + + /* Loop until all data is written */ + while (*retlen < len) { + /* Invalidate cache, if we write to this page */ + if (nand->cache_page == page) + nand->cache_page = -1; + + /* Write data into buffer */ + if ((col + len) >= nand->oobblock) { + for (i = col, cnt = 0; i < nand->oobblock; i++, cnt++) { + nand->data_buf[i] = buf[(*retlen + cnt)]; + } + } else { + for (i = col, cnt = 0; cnt < (len - *retlen); i++, cnt++) { + nand->data_buf[i] = buf[(*retlen + cnt)]; + } + } + /* We use the same function for write and writev !) */ + ret = nand_write_page (nand, page, col, i, ecc_code); + if (ret) + goto out; + + /* Next data start at page boundary */ + col = 0; + + /* Update written bytes count */ + *retlen += cnt; + + /* Increment page address */ + page++; + } + + /* Return happy */ + *retlen = len; + +out: + /* De-select the NAND device */ + NAND_DISABLE_CE(nand); /* set pin high */ +#ifdef CONFIG_OMAP1510 + archflashwp(0,1); +#endif +#ifdef CFG_NAND_WP + NAND_WP_ON(); +#endif + + return ret; +} + +/* read from the 16 bytes of oob data that correspond to a 512 byte + * page or 2 256-byte pages. + */ +static int nand_read_oob(struct nand_chip* nand, size_t ofs, size_t len, + size_t * retlen, u_char * buf) +{ + int len256 = 0; + struct Nand *mychip; + int ret = 0; + + mychip = &nand->chips[ofs >> nand->chipshift]; + + /* update address for 2M x 8bit devices. OOB starts on the second */ + /* page to maintain compatibility with nand_read_ecc. */ + if (nand->page256) { + if (!(ofs & 0x8)) + ofs += 0x100; + else + ofs -= 0x8; + } + + NAND_ENABLE_CE(nand); /* set pin low */ + NanD_Command(nand, NAND_CMD_READOOB); + if (nand->bus16) { + NanD_Address(nand, ADDR_COLUMN_PAGE, + ((ofs >> nand->page_shift) << nand->page_shift) + + ((ofs & (nand->oobblock - 1)) >> 1)); + } else { + NanD_Address(nand, ADDR_COLUMN_PAGE, ofs); + } + + /* treat crossing 8-byte OOB data for 2M x 8bit devices */ + /* Note: datasheet says it should automaticaly wrap to the */ + /* next OOB block, but it didn't work here. mf. */ + if (nand->page256 && ofs + len > (ofs | 0x7) + 1) { + len256 = (ofs | 0x7) + 1 - ofs; + NanD_ReadBuf(nand, buf, len256); + + NanD_Command(nand, NAND_CMD_READOOB); + NanD_Address(nand, ADDR_COLUMN_PAGE, ofs & (~0x1ff)); + } + + NanD_ReadBuf(nand, &buf[len256], len - len256); + + *retlen = len; + /* Reading the full OOB data drops us off of the end of the page, + * causing the flash device to go into busy mode, so we need + * to wait until ready 11.4.1 and Toshiba TC58256FT nands */ + + ret = NanD_WaitReady(nand, 1); + NAND_DISABLE_CE(nand); /* set pin high */ + + return ret; + +} + +/* write to the 16 bytes of oob data that correspond to a 512 byte + * page or 2 256-byte pages. + */ +static int nand_write_oob(struct nand_chip* nand, size_t ofs, size_t len, + size_t * retlen, const u_char * buf) +{ + int len256 = 0; + int i; + unsigned long nandptr = nand->IO_ADDR; + +#ifdef PSYCHO_DEBUG + printf("nand_write_oob(%lx, %d): %2.2X %2.2X %2.2X %2.2X ... %2.2X %2.2X .. %2.2X %2.2X\n", + (long)ofs, len, buf[0], buf[1], buf[2], buf[3], + buf[8], buf[9], buf[14],buf[15]); +#endif + + NAND_ENABLE_CE(nand); /* set pin low to enable chip */ + + /* Reset the chip */ + NanD_Command(nand, NAND_CMD_RESET); + + /* issue the Read2 command to set the pointer to the Spare Data Area. */ + NanD_Command(nand, NAND_CMD_READOOB); + if (nand->bus16) { + NanD_Address(nand, ADDR_COLUMN_PAGE, + ((ofs >> nand->page_shift) << nand->page_shift) + + ((ofs & (nand->oobblock - 1)) >> 1)); + } else { + NanD_Address(nand, ADDR_COLUMN_PAGE, ofs); + } + + /* update address for 2M x 8bit devices. OOB starts on the second */ + /* page to maintain compatibility with nand_read_ecc. */ + if (nand->page256) { + if (!(ofs & 0x8)) + ofs += 0x100; + else + ofs -= 0x8; + } + + /* issue the Serial Data In command to initial the Page Program process */ + NanD_Command(nand, NAND_CMD_SEQIN); + if (nand->bus16) { + NanD_Address(nand, ADDR_COLUMN_PAGE, + ((ofs >> nand->page_shift) << nand->page_shift) + + ((ofs & (nand->oobblock - 1)) >> 1)); + } else { + NanD_Address(nand, ADDR_COLUMN_PAGE, ofs); + } + + /* treat crossing 8-byte OOB data for 2M x 8bit devices */ + /* Note: datasheet says it should automaticaly wrap to the */ + /* next OOB block, but it didn't work here. mf. */ + if (nand->page256 && ofs + len > (ofs | 0x7) + 1) { + len256 = (ofs | 0x7) + 1 - ofs; + for (i = 0; i < len256; i++) + WRITE_NAND(buf[i], nandptr); + + NanD_Command(nand, NAND_CMD_PAGEPROG); + NanD_Command(nand, NAND_CMD_STATUS); +#ifdef NAND_NO_RB + { u_char ret_val; + do { + ret_val = READ_NAND(nandptr); /* wait till ready */ + } while ((ret_val & 0x40) != 0x40); + } +#endif + if (READ_NAND(nandptr) & 1) { + puts ("Error programming oob data\n"); + /* There was an error */ + NAND_DISABLE_CE(nand); /* set pin high */ + *retlen = 0; + return -1; + } + NanD_Command(nand, NAND_CMD_SEQIN); + NanD_Address(nand, ADDR_COLUMN_PAGE, ofs & (~0x1ff)); + } + + if (nand->bus16) { + for (i = len256; i < len; i += 2) { + WRITE_NAND(buf[i] + (buf[i+1] << 8), nandptr); + } + } else { + for (i = len256; i < len; i++) + WRITE_NAND(buf[i], nandptr); + } + + NanD_Command(nand, NAND_CMD_PAGEPROG); + NanD_Command(nand, NAND_CMD_STATUS); +#ifdef NAND_NO_RB + { u_char ret_val; + do { + ret_val = READ_NAND(nandptr); /* wait till ready */ + } while ((ret_val & 0x40) != 0x40); + } +#endif + if (READ_NAND(nandptr) & 1) { + puts ("Error programming oob data\n"); + /* There was an error */ + NAND_DISABLE_CE(nand); /* set pin high */ + *retlen = 0; + return -1; + } + + NAND_DISABLE_CE(nand); /* set pin high */ + *retlen = len; + return 0; + +} + +int nand_erase(struct nand_chip* nand, size_t ofs, size_t len, int clean) +{ + /* This is defined as a structure so it will work on any system + * using native endian jffs2 (the default). + */ + static struct jffs2_unknown_node clean_marker = { + JFFS2_MAGIC_BITMASK, + JFFS2_NODETYPE_CLEANMARKER, + 8 /* 8 bytes in this node */ + }; + unsigned long nandptr; + struct Nand *mychip; + int ret = 0; + + if (ofs & (nand->erasesize-1) || len & (nand->erasesize-1)) { + printf ("Offset and size must be sector aligned, erasesize = %d\n", + (int) nand->erasesize); + return -1; + } + + nandptr = nand->IO_ADDR; + + /* Select the NAND device */ +#ifdef CONFIG_OMAP1510 + archflashwp(0,0); +#endif +#ifdef CFG_NAND_WP + NAND_WP_OFF(); +#endif + NAND_ENABLE_CE(nand); /* set pin low */ + + /* Check the WP bit */ + NanD_Command(nand, NAND_CMD_STATUS); + if (!(READ_NAND(nand->IO_ADDR) & 0x80)) { + printf ("nand_write_ecc: Device is write protected!!!\n"); + ret = -1; + goto out; + } + + /* Check the WP bit */ + NanD_Command(nand, NAND_CMD_STATUS); + if (!(READ_NAND(nand->IO_ADDR) & 0x80)) { + printf ("%s: Device is write protected!!!\n", __FUNCTION__); + ret = -1; + goto out; + } + + /* FIXME: Do nand in the background. Use timers or schedule_task() */ + while(len) { + /*mychip = &nand->chips[shr(ofs, nand->chipshift)];*/ + mychip = &nand->chips[ofs >> nand->chipshift]; + + /* always check for bad block first, genuine bad blocks + * should _never_ be erased. + */ + if (ALLOW_ERASE_BAD_DEBUG || !check_block(nand, ofs)) { + /* Select the NAND device */ + NAND_ENABLE_CE(nand); /* set pin low */ + + NanD_Command(nand, NAND_CMD_ERASE1); + NanD_Address(nand, ADDR_PAGE, ofs); + NanD_Command(nand, NAND_CMD_ERASE2); + + NanD_Command(nand, NAND_CMD_STATUS); + +#ifdef NAND_NO_RB + { u_char ret_val; + do { + ret_val = READ_NAND(nandptr); /* wait till ready */ + } while ((ret_val & 0x40) != 0x40); + } +#endif + if (READ_NAND(nandptr) & 1) { + printf ("%s: Error erasing at 0x%lx\n", + __FUNCTION__, (long)ofs); + /* There was an error */ + ret = -1; + goto out; + } + if (clean) { + int n; /* return value not used */ + int p, l; + + /* clean marker position and size depend + * on the page size, since 256 byte pages + * only have 8 bytes of oob data + */ + if (nand->page256) { + p = NAND_JFFS2_OOB8_FSDAPOS; + l = NAND_JFFS2_OOB8_FSDALEN; + } else { + p = NAND_JFFS2_OOB16_FSDAPOS; + l = NAND_JFFS2_OOB16_FSDALEN; + } + + ret = nand_write_oob(nand, ofs + p, l, &n, + (u_char *)&clean_marker); + /* quit here if write failed */ + if (ret) + goto out; + } + } + ofs += nand->erasesize; + len -= nand->erasesize; + } + +out: + /* De-select the NAND device */ + NAND_DISABLE_CE(nand); /* set pin high */ +#ifdef CONFIG_OMAP1510 + archflashwp(0,1); +#endif +#ifdef CFG_NAND_WP + NAND_WP_ON(); +#endif + + return ret; +} + +static inline int nandcheck(unsigned long potential, unsigned long physadr) +{ + return 0; +} + +unsigned long nand_probe(unsigned long physadr) +{ + struct nand_chip *nand = NULL; + int i = 0, ChipID = 1; + +#ifdef CONFIG_MTD_NAND_ECC_JFFS2 + oob_config.ecc_pos[0] = NAND_JFFS2_OOB_ECCPOS0; + oob_config.ecc_pos[1] = NAND_JFFS2_OOB_ECCPOS1; + oob_config.ecc_pos[2] = NAND_JFFS2_OOB_ECCPOS2; + oob_config.ecc_pos[3] = NAND_JFFS2_OOB_ECCPOS3; + oob_config.ecc_pos[4] = NAND_JFFS2_OOB_ECCPOS4; + oob_config.ecc_pos[5] = NAND_JFFS2_OOB_ECCPOS5; + oob_config.eccvalid_pos = 4; +#else + oob_config.ecc_pos[0] = NAND_NOOB_ECCPOS0; + oob_config.ecc_pos[1] = NAND_NOOB_ECCPOS1; + oob_config.ecc_pos[2] = NAND_NOOB_ECCPOS2; + oob_config.ecc_pos[3] = NAND_NOOB_ECCPOS3; + oob_config.ecc_pos[4] = NAND_NOOB_ECCPOS4; + oob_config.ecc_pos[5] = NAND_NOOB_ECCPOS5; + oob_config.eccvalid_pos = NAND_NOOB_ECCVPOS; +#endif + oob_config.badblock_pos = 5; + + for (i=0; iIO_ADDR = physadr; + nand->cache_page = -1; /* init the cache page */ + NanD_ScanChips(nand); + + if (nand->totlen == 0) { + /* no chips found, clean up and quit */ + memset((char *)nand, 0, sizeof(struct nand_chip)); + nand->ChipID = NAND_ChipID_UNKNOWN; + return (0); + } + + nand->ChipID = ChipID; + if (curr_device == -1) + curr_device = i; + + nand->data_buf = malloc (nand->oobblock + nand->oobsize); + if (!nand->data_buf) { + puts ("Cannot allocate memory for data structures.\n"); + return (0); + } + + return (nand->totlen); +} + +#ifdef CONFIG_MTD_NAND_ECC +/* + * Pre-calculated 256-way 1 byte column parity + */ +static const u_char nand_ecc_precalc_table[] = { + 0x00, 0x55, 0x56, 0x03, 0x59, 0x0c, 0x0f, 0x5a, + 0x5a, 0x0f, 0x0c, 0x59, 0x03, 0x56, 0x55, 0x00, + 0x65, 0x30, 0x33, 0x66, 0x3c, 0x69, 0x6a, 0x3f, + 0x3f, 0x6a, 0x69, 0x3c, 0x66, 0x33, 0x30, 0x65, + 0x66, 0x33, 0x30, 0x65, 0x3f, 0x6a, 0x69, 0x3c, + 0x3c, 0x69, 0x6a, 0x3f, 0x65, 0x30, 0x33, 0x66, + 0x03, 0x56, 0x55, 0x00, 0x5a, 0x0f, 0x0c, 0x59, + 0x59, 0x0c, 0x0f, 0x5a, 0x00, 0x55, 0x56, 0x03, + 0x69, 0x3c, 0x3f, 0x6a, 0x30, 0x65, 0x66, 0x33, + 0x33, 0x66, 0x65, 0x30, 0x6a, 0x3f, 0x3c, 0x69, + 0x0c, 0x59, 0x5a, 0x0f, 0x55, 0x00, 0x03, 0x56, + 0x56, 0x03, 0x00, 0x55, 0x0f, 0x5a, 0x59, 0x0c, + 0x0f, 0x5a, 0x59, 0x0c, 0x56, 0x03, 0x00, 0x55, + 0x55, 0x00, 0x03, 0x56, 0x0c, 0x59, 0x5a, 0x0f, + 0x6a, 0x3f, 0x3c, 0x69, 0x33, 0x66, 0x65, 0x30, + 0x30, 0x65, 0x66, 0x33, 0x69, 0x3c, 0x3f, 0x6a, + 0x6a, 0x3f, 0x3c, 0x69, 0x33, 0x66, 0x65, 0x30, + 0x30, 0x65, 0x66, 0x33, 0x69, 0x3c, 0x3f, 0x6a, + 0x0f, 0x5a, 0x59, 0x0c, 0x56, 0x03, 0x00, 0x55, + 0x55, 0x00, 0x03, 0x56, 0x0c, 0x59, 0x5a, 0x0f, + 0x0c, 0x59, 0x5a, 0x0f, 0x55, 0x00, 0x03, 0x56, + 0x56, 0x03, 0x00, 0x55, 0x0f, 0x5a, 0x59, 0x0c, + 0x69, 0x3c, 0x3f, 0x6a, 0x30, 0x65, 0x66, 0x33, + 0x33, 0x66, 0x65, 0x30, 0x6a, 0x3f, 0x3c, 0x69, + 0x03, 0x56, 0x55, 0x00, 0x5a, 0x0f, 0x0c, 0x59, + 0x59, 0x0c, 0x0f, 0x5a, 0x00, 0x55, 0x56, 0x03, + 0x66, 0x33, 0x30, 0x65, 0x3f, 0x6a, 0x69, 0x3c, + 0x3c, 0x69, 0x6a, 0x3f, 0x65, 0x30, 0x33, 0x66, + 0x65, 0x30, 0x33, 0x66, 0x3c, 0x69, 0x6a, 0x3f, + 0x3f, 0x6a, 0x69, 0x3c, 0x66, 0x33, 0x30, 0x65, + 0x00, 0x55, 0x56, 0x03, 0x59, 0x0c, 0x0f, 0x5a, + 0x5a, 0x0f, 0x0c, 0x59, 0x03, 0x56, 0x55, 0x00 +}; + + +/* + * Creates non-inverted ECC code from line parity + */ +static void nand_trans_result(u_char reg2, u_char reg3, + u_char *ecc_code) +{ + u_char a, b, i, tmp1, tmp2; + + /* Initialize variables */ + a = b = 0x80; + tmp1 = tmp2 = 0; + + /* Calculate first ECC byte */ + for (i = 0; i < 4; i++) { + if (reg3 & a) /* LP15,13,11,9 --> ecc_code[0] */ + tmp1 |= b; + b >>= 1; + if (reg2 & a) /* LP14,12,10,8 --> ecc_code[0] */ + tmp1 |= b; + b >>= 1; + a >>= 1; + } + + /* Calculate second ECC byte */ + b = 0x80; + for (i = 0; i < 4; i++) { + if (reg3 & a) /* LP7,5,3,1 --> ecc_code[1] */ + tmp2 |= b; + b >>= 1; + if (reg2 & a) /* LP6,4,2,0 --> ecc_code[1] */ + tmp2 |= b; + b >>= 1; + a >>= 1; + } + + /* Store two of the ECC bytes */ + ecc_code[0] = tmp1; + ecc_code[1] = tmp2; +} + +/* + * Calculate 3 byte ECC code for 256 byte block + */ +static void nand_calculate_ecc (const u_char *dat, u_char *ecc_code) +{ + u_char idx, reg1, reg3; + int j; + + /* Initialize variables */ + reg1 = reg3 = 0; + ecc_code[0] = ecc_code[1] = ecc_code[2] = 0; + + /* Build up column parity */ + for(j = 0; j < 256; j++) { + + /* Get CP0 - CP5 from table */ + idx = nand_ecc_precalc_table[dat[j]]; + reg1 ^= idx; + + /* All bit XOR = 1 ? */ + if (idx & 0x40) { + reg3 ^= (u_char) j; + } + } + + /* Create non-inverted ECC code from line parity */ + nand_trans_result((reg1 & 0x40) ? ~reg3 : reg3, reg3, ecc_code); + + /* Calculate final ECC code */ + ecc_code[0] = ~ecc_code[0]; + ecc_code[1] = ~ecc_code[1]; + ecc_code[2] = ((~reg1) << 2) | 0x03; +} + +/* + * Detect and correct a 1 bit error for 256 byte block + */ +static int nand_correct_data (u_char *dat, u_char *read_ecc, u_char *calc_ecc) +{ + u_char a, b, c, d1, d2, d3, add, bit, i; + + /* Do error detection */ + d1 = calc_ecc[0] ^ read_ecc[0]; + d2 = calc_ecc[1] ^ read_ecc[1]; + d3 = calc_ecc[2] ^ read_ecc[2]; + + if ((d1 | d2 | d3) == 0) { + /* No errors */ + return 0; + } else { + a = (d1 ^ (d1 >> 1)) & 0x55; + b = (d2 ^ (d2 >> 1)) & 0x55; + c = (d3 ^ (d3 >> 1)) & 0x54; + + /* Found and will correct single bit error in the data */ + if ((a == 0x55) && (b == 0x55) && (c == 0x54)) { + c = 0x80; + add = 0; + a = 0x80; + for (i=0; i<4; i++) { + if (d1 & c) + add |= a; + c >>= 2; + a >>= 1; + } + c = 0x80; + for (i=0; i<4; i++) { + if (d2 & c) + add |= a; + c >>= 2; + a >>= 1; + } + bit = 0; + b = 0x04; + c = 0x80; + for (i=0; i<3; i++) { + if (d3 & c) + bit |= b; + c >>= 2; + b >>= 1; + } + b = 0x01; + a = dat[add]; + a ^= (b << bit); + dat[add] = a; + return 1; + } + else { + i = 0; + while (d1) { + if (d1 & 0x01) + ++i; + d1 >>= 1; + } + while (d2) { + if (d2 & 0x01) + ++i; + d2 >>= 1; + } + while (d3) { + if (d3 & 0x01) + ++i; + d3 >>= 1; + } + if (i == 1) { + /* ECC Code Error Correction */ + read_ecc[0] = calc_ecc[0]; + read_ecc[1] = calc_ecc[1]; + read_ecc[2] = calc_ecc[2]; + return 2; + } + else { + /* Uncorrectable Error */ + return -1; + } + } + } + + /* Should never happen */ + return -1; +} + +#endif + +#ifdef CONFIG_JFFS2_NAND + +int read_jffs2_nand(size_t start, size_t len, + size_t * retlen, u_char * buf, int nanddev) +{ + return nand_rw(nand_dev_desc + nanddev, NANDRW_READ | NANDRW_JFFS2, + start, len, retlen, buf); +} +#endif /* CONFIG_JFFS2_NAND */ -#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */ +#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */ diff --git a/common/cmd_nand_new.c b/common/cmd_nand_new.c new file mode 100644 index 0000000000..3ff2ebaf60 --- /dev/null +++ b/common/cmd_nand_new.c @@ -0,0 +1,364 @@ +#include + +#if (CONFIG_COMMANDS & CFG_CMD_NAND) && defined CONFIG_NEW_NAND_CODE + +#include +#include +#include +#include + +#ifdef CONFIG_SHOW_BOOT_PROGRESS +# include +# define SHOW_BOOT_PROGRESS(arg) show_boot_progress(arg) +#else +# define SHOW_BOOT_PROGRESS(arg) +#endif + +#include +#include + +extern nand_info_t nand_info[]; /* info for NAND chips */ + +static int nand_dump_oob(nand_info_t *nand, ulong off) +{ + return 0; +} + +static int nand_dump(nand_info_t *nand, ulong off) +{ + int i; + u_char *buf, *p; + + buf = malloc(nand->oobblock + nand->oobsize); + if (!buf) { + puts("No memory for page buffer\n"); + return 1; + } + off &= ~(nand->oobblock - 1); + i = nand_read_raw(nand, buf, off, nand->oobblock, nand->oobsize); + if (i < 0) { + printf("Error (%d) reading page %08x\n", i, off); + free(buf); + return 1; + } + printf("Page %08x dump:\n", off); + i = nand->oobblock >> 4; p = buf; + while (i--) { + printf( "\t%02x %02x %02x %02x %02x %02x %02x %02x" + " %02x %02x %02x %02x %02x %02x %02x %02x\n", + p[0], p[1], p[2], p[3], p[4], p[5], p[6], p[7], + p[8], p[9], p[10], p[11], p[12], p[13], p[14], p[15]); + p += 16; + } + puts("OOB:\n"); + i = nand->oobsize >> 3; + while (i--) { + printf( "\t%02x %02x %02x %02x %02x %02x %02x %02x\n", + p[0], p[1], p[2], p[3], p[4], p[5], p[6], p[7]); + p += 8; + } + free(buf); + + return 0; +} + +/* ------------------------------------------------------------------------- */ + +static void +arg_off_size(int argc, char *argv[], ulong *off, ulong *size, ulong totsize) +{ + *off = 0; + *size = 0; + +#if defined(CONFIG_JFFS2_NAND) && defined(CFG_JFFS_CUSTOM_PART) + if (argc >= 1 && strcmp(argv[0], "partition") == 0) { + int part_num; + struct part_info *part; + const char *partstr; + + if (argc >= 2) + partstr = argv[1]; + else + partstr = getenv("partition"); + + if (partstr) + part_num = (int)simple_strtoul(partstr, NULL, 10); + else + part_num = 0; + + part = jffs2_part_info(part_num); + if (part == NULL) { + printf("\nInvalid partition %d\n", part_num); + return; + } + *size = part->size; + *off = (ulong)part->offset; + } else +#endif + { + if (argc >= 1) + *off = (ulong)simple_strtoul(argv[0], NULL, 16); + else + *off = 0; + + if (argc >= 2) + *size = (ulong)simple_strtoul(argv[1], NULL, 16); + else + *size = totsize - *off; + + } + +} + +int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) +{ + int i, dev, ret; + ulong addr, off, size; + char *cmd, *s; + nand_info_t *nand; + + /* at least two arguments please */ + if (argc < 2) + goto usage; + + cmd = argv[1]; + + if (strcmp(cmd, "info") == 0) { + + putc('\n'); + for (i = 0; i < CFG_MAX_NAND_DEVICE; i++) { + if (nand_info[i].name) + printf("Device %d: %s\n", i, nand_info[i].name); + } + return 0; + } + + if (strcmp(cmd, "device") == 0) { + + if (argc < 3) { + if ((nand_curr_device < 0) || + (nand_curr_device >= CFG_MAX_NAND_DEVICE)) + puts("\nno devices available\n"); + else + printf("\nDevice %d: %s\n", nand_curr_device, + nand_info[nand_curr_device].name); + return 0; + } + dev = (int)simple_strtoul(argv[2], NULL, 10); + if (dev < 0 || dev >= CFG_MAX_NAND_DEVICE || !nand_info[dev].name) { + puts("No such device\n"); + return 1; + } + printf("Device %d: %s", dev, nand_info[dev].name); + puts("... is now current device\n"); + nand_curr_device = dev; + return 0; + } + + if (strcmp(cmd, "bad") != 0 && strcmp(cmd, "erase") != 0 && + strncmp(cmd, "dump", 4) != 0 && + strncmp(cmd, "read", 4) != 0 && strncmp(cmd, "write", 5) != 0) + goto usage; + + /* the following commands operate on the current device */ + if (nand_curr_device < 0 || nand_curr_device >= CFG_MAX_NAND_DEVICE || + !nand_info[nand_curr_device].name) { + puts("\nno devices available\n"); + return 1; + } + nand = &nand_info[nand_curr_device]; + + if (strcmp(cmd, "bad") == 0) { + printf("\nDevice %d bad blocks:\n", nand_curr_device); + for (off = 0; off < nand->size; off += nand->erasesize) + if (nand_block_isbad(nand, off)) + printf(" %08x\n", off); + return 0; + } + + if (strcmp(cmd, "erase") == 0) { + arg_off_size(argc - 2, argv + 2, &off, &size, nand->size); + if (off == 0 && size == 0) + return 1; + + printf("\nNAND erase: device %d offset 0x%x, size 0x%x ", + nand_curr_device, off, size); + ret = nand_erase(nand, off, size); + printf("%s\n", ret ? "ERROR" : "OK"); + + return ret == 0 ? 0 : 1; + } + + if (strncmp(cmd, "dump", 4) == 0) { + if (argc < 3) + goto usage; + + s = strchr(cmd, '.'); + off = (int)simple_strtoul(argv[2], NULL, 16); + + if (s != NULL && strcmp(s, ".oob") == 0) + ret = nand_dump_oob(nand, off); + else + ret = nand_dump(nand, off); + + return ret == 0 ? 1 : 0; + + } + + /* read write */ + if (strncmp(cmd, "read", 4) == 0 || strncmp(cmd, "write", 5) == 0) { + if (argc < 4) + goto usage; +/* + s = strchr(cmd, '.'); + clean = CLEAN_NONE; + if (s != NULL) { + if (strcmp(s, ".jffs2") == 0 || strcmp(s, ".e") == 0 + || strcmp(s, ".i")) + clean = CLEAN_JFFS2; + } +*/ + addr = (ulong)simple_strtoul(argv[2], NULL, 16); + + arg_off_size(argc - 3, argv + 3, &off, &size, nand->size); + if (off == 0 && size == 0) + return 1; + + i = strncmp(cmd, "read", 4) == 0; /* 1 = read, 0 = write */ + printf("\nNAND %s: device %d offset %u, size %u ... ", + i ? "read" : "write", nand_curr_device, off, size); + + if (i) + ret = nand_read(nand, off, &size, (u_char *)addr); + else + ret = nand_write(nand, off, &size, (u_char *)addr); + + printf(" %d bytes %s: %s\n", size, + i ? "read" : "written", ret ? "ERROR" : "OK"); + + return ret == 0 ? 0 : 1; + } +usage: + printf("Usage:\n%s\n", cmdtp->usage); + return 1; +} + +U_BOOT_CMD(nand, 5, 1, do_nand, + "nand - NAND sub-system\n", + "info - show available NAND devices\n" + "nand device [dev] - show or set current device\n" + "nand read[.jffs2] - addr off size\n" + "nand write[.jffs2] - addr off size - read/write `size' bytes starting\n" + " at offset `off' to/from memory address `addr'\n" + "nand erase [clean] [off size] - erase `size' bytes from\n" + " offset `off' (entire device if not specified)\n" + "nand bad - show bad blocks\n" + "nand dump[.oob] off - dump page\n" + "nand scrub - really clean NAND erasing bad blocks (UNSAFE)\n" + "nand markbad off - mark bad block at offset (UNSAFE)\n" + "nand biterr off - make a bit error at offset (UNSAFE)\n"); + +int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) +{ + char *boot_device = NULL; + char *ep; + int dev; + int r; + ulong addr, cnt, offset = 0; + image_header_t *hdr; + nand_info_t *nand; + + switch (argc) { + case 1: + addr = CFG_LOAD_ADDR; + boot_device = getenv("bootdevice"); + break; + case 2: + addr = simple_strtoul(argv[1], NULL, 16); + boot_device = getenv("bootdevice"); + break; + case 3: + addr = simple_strtoul(argv[1], NULL, 16); + boot_device = argv[2]; + break; + case 4: + addr = simple_strtoul(argv[1], NULL, 16); + boot_device = argv[2]; + offset = simple_strtoul(argv[3], NULL, 16); + break; + default: + printf("Usage:\n%s\n", cmdtp->usage); + SHOW_BOOT_PROGRESS(-1); + return 1; + } + + if (!boot_device) { + puts("\n** No boot device **\n"); + SHOW_BOOT_PROGRESS(-1); + return 1; + } + + dev = simple_strtoul(boot_device, &ep, 16); + + if (dev < 0 || dev >= CFG_MAX_NAND_DEVICE || !nand_info[dev].name) { + printf("\n** Device %d not available\n", dev); + SHOW_BOOT_PROGRESS(-1); + return 1; + } + + nand = &nand_info[dev]; + printf("\nLoading from device %d: %s (offset 0x%lx)\n", + dev, nand->name, offset); + + cnt = nand->oobblock; + r = nand_read(nand, offset, &cnt, (u_char *) addr); + if (r) { + printf("** Read error on %d\n", dev); + SHOW_BOOT_PROGRESS(-1); + return 1; + } + + hdr = (image_header_t *) addr; + + if (ntohl(hdr->ih_magic) != IH_MAGIC) { + printf("\n** Bad Magic Number 0x%x **\n", hdr->ih_magic); + SHOW_BOOT_PROGRESS(-1); + return 1; + } + + print_image_hdr(hdr); + + cnt = (ntohl(hdr->ih_size) + sizeof (image_header_t)); + + r = nand_read(nand, offset, &cnt, (u_char *) addr); + if (r) { + printf("** Read error on %d\n", dev); + SHOW_BOOT_PROGRESS(-1); + return 1; + } + + /* Loading ok, update default load address */ + + load_addr = addr; + + /* Check if we should attempt an auto-start */ + if (((ep = getenv("autostart")) != NULL) && (strcmp(ep, "yes") == 0)) { + char *local_args[2]; + extern int do_bootm(cmd_tbl_t *, int, int, char *[]); + + local_args[0] = argv[0]; + local_args[1] = NULL; + + printf("Automatic boot of image at addr 0x%08lx ...\n", addr); + + do_bootm(cmdtp, 0, 1, local_args); + return 1; + } + return 0; +} + +U_BOOT_CMD(nboot, 4, 1, do_nandboot, + "nboot - boot from NAND device\n", "loadAddr dev\n"); + + +#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */ -- cgit v1.2.1 From 8e9655f863246db60c51140153186acc2afdc855 Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Wed, 2 Nov 2005 14:29:12 +0100 Subject: * Add hook to NAND erase and implement nand_wait function. Patch by Mike Rapoport, 01 Nov 2005 Signed-off-by: Ladislav Michl --- common/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'common') diff --git a/common/Makefile b/common/Makefile index 209e17d816..9bfc11ab50 100644 --- a/common/Makefile +++ b/common/Makefile @@ -37,7 +37,7 @@ COBJS = main.o ACEX1K.o altera.o bedbug.o circbuf.o \ cmd_i2c.o cmd_ide.o cmd_immap.o cmd_itest.o cmd_jffs2.o \ cmd_load.o cmd_log.o \ cmd_mem.o cmd_mii.o cmd_misc.o cmd_mmc.o \ - cmd_nand.o cmd_net.o cmd_nvedit.o \ + cmd_nand.o cmd_nand_new.o cmd_net.o cmd_nvedit.o \ cmd_pci.o cmd_pcmcia.o cmd_portio.o \ cmd_reginfo.o cmd_reiser.o cmd_scsi.o cmd_spi.o cmd_universe.o cmd_usb.o cmd_vfd.o \ command.o console.o devices.o dlmalloc.o docecc.o \ -- cgit v1.2.1