From 062ef1a662ee5b3292805d8fe458f1baead21281 Mon Sep 17 00:00:00 2001 From: Priyanka Jain Date: Fri, 18 Oct 2013 17:19:06 +0530 Subject: powerpc/t104xrdb: Add T1040RDB board support MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit T1040RDB is Freescale Reference Design Board supporting the T1040 QorIQ Power Architecture™ processor. T1040RDB board Overview ----------------------- - Four e5500 cores, each with a private 256 KB L2 cache - 256 KB shared L3 CoreNet platform cache (CPC) - Interconnect CoreNet platform - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: - Packet parsing, classification, and distribution - Queue management for scheduling, packet sequencing, and congestion management - Cryptography Acceleration - RegEx Pattern Matching Acceleration - IEEE Std 1588 support - Hardware buffer management for buffer allocation and deallocation - Ethernet interfaces - Integrated 8-port Gigabit Ethernet switch - Four 1 Gbps Ethernet controllers - SERDES Connections, 8 lanes supporting: - PCI - SGMII - QSGMII - SATA 2.0 - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and Interleaving -IFC/Local Bus - NAND flash: 1GB 8-bit NAND flash - NOR: 128MB 16-bit NOR Flash - Ethernet - Two on-board RGMII 10/100/1G ethernet ports. - PHY #0 remains powered up during deep-sleep - CPLD - Clocks - System and DDR clock (SYSCLK, “DDRCLK”) - SERDES clocks - Power Supplies - USB - Supports two USB 2.0 ports with integrated PHYs - Two type A ports with 5V@1.5A per port. - SDHC - SDHC/SDXC connector - SPI - On-board 64MB SPI flash - I2C - Devices connected: EEPROM, thermal monitor, VID controller - Other IO - Two Serial ports - ProfiBus port Signed-off-by: Poonam Aggrwal Signed-off-by: Prabhakar Kushwaha Signed-off-by: Priyanka Jain [York Sun: fixed Makefile] Acked-by: York Sun --- board/freescale/t104xrdb/Makefile | 12 +++ board/freescale/t104xrdb/README | 162 ++++++++++++++++++++++++++++++++++++ board/freescale/t104xrdb/ddr.c | 132 +++++++++++++++++++++++++++++ board/freescale/t104xrdb/ddr.h | 76 +++++++++++++++++ board/freescale/t104xrdb/law.c | 32 +++++++ board/freescale/t104xrdb/pci.c | 23 +++++ board/freescale/t104xrdb/t104xrdb.c | 93 +++++++++++++++++++++ board/freescale/t104xrdb/t104xrdb.h | 13 +++ board/freescale/t104xrdb/tlb.c | 107 ++++++++++++++++++++++++ 9 files changed, 650 insertions(+) create mode 100644 board/freescale/t104xrdb/Makefile create mode 100644 board/freescale/t104xrdb/README create mode 100644 board/freescale/t104xrdb/ddr.c create mode 100644 board/freescale/t104xrdb/ddr.h create mode 100644 board/freescale/t104xrdb/law.c create mode 100644 board/freescale/t104xrdb/pci.c create mode 100644 board/freescale/t104xrdb/t104xrdb.c create mode 100644 board/freescale/t104xrdb/t104xrdb.h create mode 100644 board/freescale/t104xrdb/tlb.c (limited to 'board') diff --git a/board/freescale/t104xrdb/Makefile b/board/freescale/t104xrdb/Makefile new file mode 100644 index 0000000000..76c0c94b0e --- /dev/null +++ b/board/freescale/t104xrdb/Makefile @@ -0,0 +1,12 @@ +# +# Copyright 2013 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + + +obj-y += t104xrdb.o +obj-y += ddr.o +obj-$(CONFIG_PCI) += pci.o +obj-y += law.o +obj-y += tlb.o diff --git a/board/freescale/t104xrdb/README b/board/freescale/t104xrdb/README new file mode 100644 index 0000000000..e8848ee7f0 --- /dev/null +++ b/board/freescale/t104xrdb/README @@ -0,0 +1,162 @@ +Overview +-------- +The T1040RDB is a Freescale reference board that hosts the T1040 SoC +(and variants). Variants inclued T1042 presonality of T1040, in which +case T1040RDB can also be called T1042RDB. + +T1040 SoC Overview +------------------ +The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA +processor cores with high-performance data path acceleration architecture +and network peripheral interfaces required for networking & telecommunications. + +The T1040/T1042 SoC includes the following function and features: + + - Four e5500 cores, each with a private 256 KB L2 cache + - 256 KB shared L3 CoreNet platform cache (CPC) + - Interconnect CoreNet platform + - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving + support + - Data Path Acceleration Architecture (DPAA) incorporating acceleration + for the following functions: + - Packet parsing, classification, and distribution + - Queue management for scheduling, packet sequencing, and congestion + management + - Cryptography Acceleration (SEC 5.0) + - RegEx Pattern Matching Acceleration (PME 2.2) + - IEEE Std 1588 support + - Hardware buffer management for buffer allocation and deallocation + - Ethernet interfaces + - Integrated 8-port Gigabit Ethernet switch (T1040 only) + - Four 1 Gbps Ethernet controllers + - Two RGMII interfaces or one RGMII and one MII interfaces + - High speed peripheral interfaces + - Four PCI Express 2.0 controllers running at up to 5 GHz + - Two SATA controllers supporting 1.5 and 3.0 Gb/s operation + - Upto two QSGMII interface + - Upto six SGMII interface supporting 1000 Mbps + - One SGMII interface supporting upto 2500 Mbps + - Additional peripheral interfaces + - Two USB 2.0 controllers with integrated PHY + - SD/eSDHC/eMMC + - eSPI controller + - Four I2C controllers + - Four UARTs + - Four GPIO controllers + - Integrated flash controller (IFC) + - LCD and HDMI interface (DIU) with 12 bit dual data rate + - TDM interface + - Multicore programmable interrupt controller (PIC) + - Two 8-channel DMA engines + - Single source clocking implementation + - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) + +T1040 SoC Personalities +------------------------- + +T1022 Personality: +T1022 is a reduced personality of T1040 with less core/clusters. + +T1042 Personality: +T1042 is a reduced personality of T1040 without Integrated 8-port Gigabit +Ethernet switch. Rest of the blocks are same as T1040 + + +T1040RDB board Overview +------------------------- + - SERDES Connections, 8 lanes information: + 1: None + 2: SGMII + 3: QSGMII + 4: QSGMII + 5: PCIe1 x1 slot + 6: mini PCIe connector + 7: mini PCIe connector + 8: SATA connector + - DDR Controller + - Supports rates of up to 1600 MHz data-rate + - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types. + - IFC/Local Bus + - NAND flash: 1GB 8-bit NAND flash + - NOR: 128MB 16-bit NOR Flash + - Ethernet + - Two on-board RGMII 10/100/1G ethernet ports. + - CPLD + - Clocks + - System and DDR clock (SYSCLK, “DDRCLK”) + - SERDES clocks + - Power Supplies + - USB + - Supports two USB 2.0 ports with integrated PHYs + - Two type A ports with 5V@1.5A per port. + - SDHC + - SDHC/SDXC connector + - SPI + - On-board 64MB SPI flash + - Other IO + - Two Serial ports + - Four I2C ports + +Memory map +----------- +The addresses in brackets are physical addresses. + +Start Address End Address Description Size +0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB +0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB +0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB +0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB +0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB +0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB +0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB +0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB +0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB +0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB +0xF_0000_0000 0xF_003F_FFFF DCSR 4MB +0xC_3000_0000 0xC_3FFF_FFFF PCI Express 4 Mem Space 256MB +0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB +0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB +0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB +0x0_0000_0000 0x0_ffff_ffff DDR 2GB + + +NOR Flash memory Map +--------------------- + Start End Definition Size +0xEFF80000 0xEFFFFFFF u-boot (current bank) 512KB +0xEFF60000 0xEFF7FFFF u-boot env (current bank) 128KB +0xEFF40000 0xEFF5FFFF FMAN Ucode (current bank) 128KB +0xED300000 0xEFF3FFFF rootfs (alt bank) 44MB + 256KB +0xEC800000 0xEC8FFFF Hardware device tree (alt bank) 1MB +0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB +0xEC000000 0xEC01FFFF RCW (alt bank) 128KB +0xEBF80000 0xEBFFFFFF u-boot (alt bank) 512KB +0xEBF60000 0xEBF7FFFF u-boot env (alt bank) 128KB +0xEBF40000 0xEBF5FFFF FMAN ucode (alt bank) 128KB +0xE9300000 0xEBF3FFFF rootfs (current bank) 44MB + 256KB +0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 11MB + 512KB +0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB +0xE8000000 0xE801FFFF RCW (current bank) 128KB + + +Various Software configurations/environment variables/commands +-------------------------------------------------------------- +The below commands apply to the board + +1. U-boot environment variable hwconfig + The default hwconfig is: + hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1: + dr_mode=host,phy_type=utmi + Note: For USB gadget set "dr_mode=peripheral" + +2. FMAN Ucode versions + fsl_fman_ucode_t1040.bin + +3. Switching to alternate bank + Commands for switching to alternate bank. + + 1. To change from vbank0 to vbank4 + => qixis_reset altbank (it will boot using vbank4) + + 2.To change from vbank4 to vbank0 + => qixis reset (it will boot using vbank0) diff --git a/board/freescale/t104xrdb/ddr.c b/board/freescale/t104xrdb/ddr.c new file mode 100644 index 0000000000..8f58dd6832 --- /dev/null +++ b/board/freescale/t104xrdb/ddr.c @@ -0,0 +1,132 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include "ddr.h" + +DECLARE_GLOBAL_DATA_PTR; + +int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, + unsigned int controller_number, + unsigned int dimm_number) +{ + const char dimm_model[] = "RAW timing DDR"; + + if ((controller_number == 0) && (dimm_number == 0)) { + memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t)); + memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); + memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1); + } + + return 0; +} + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; + ulong ddr_freq; + + if (ctrl_num > 1) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + if (!pdimm->n_ranks) + return; + + pbsp = udimms[0]; + + /* Get clk_adjust, cpo, write_data_delay,2t, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + while (pbsp->datarate_mhz_high) { + if (pbsp->n_ranks == pdimm->n_ranks && + (pdimm->rank_density >> 30) >= pbsp->rank_gb) { + if (ddr_freq <= pbsp->datarate_mhz_high) { + popts->cpo_override = pbsp->cpo; + popts->write_data_delay = + pbsp->write_data_delay; + popts->clk_adjust = pbsp->clk_adjust; + popts->wrlvl_start = pbsp->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + popts->twot_en = pbsp->force_2t; + goto found; + } + pbsp_highest = pbsp; + } + pbsp++; + } + + if (pbsp_highest) { + printf("Error: board specific timing not found\n"); + printf("for data rate %lu MT/s\n", ddr_freq); + printf("Trying to use the highest speed (%u) parameters\n", + pbsp_highest->datarate_mhz_high); + popts->cpo_override = pbsp_highest->cpo; + popts->write_data_delay = pbsp_highest->write_data_delay; + popts->clk_adjust = pbsp_highest->clk_adjust; + popts->wrlvl_start = pbsp_highest->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + popts->twot_en = pbsp_highest->force_2t; + } else { + panic("DIMM is not supported by this board"); + } +found: + debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n" + "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, " + "wrlvl_ctrl_3 0x%x\n", + pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb, + pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2, + pbsp->wrlvl_ctl_3); + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * rtt and rtt_wr override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size; + + puts("Initializing....using SPD\n"); + + dram_size = fsl_ddr_sdram(); + + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; + + puts(" DDR: "); + return dram_size; +} diff --git a/board/freescale/t104xrdb/ddr.h b/board/freescale/t104xrdb/ddr.h new file mode 100644 index 0000000000..9276b596ac --- /dev/null +++ b/board/freescale/t104xrdb/ddr.h @@ -0,0 +1,76 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __DDR_H__ +#define __DDR_H__ + +dimm_params_t ddr_raw_timing = { + .n_ranks = 2, + .rank_density = 2147483648u, + .capacity = 4294967296u, + .primary_sdram_width = 64, + .ec_sdram_width = 8, + .registered_dimm = 0, + .mirrored_dimm = 1, + .n_row_addr = 15, + .n_col_addr = 10, + .n_banks_per_sdram_device = 8, + .edc_config = 2, /* ECC */ + .burst_lengths_bitmask = 0x0c, + + .tckmin_x_ps = 1071, + .caslat_x = 0x2fe << 4, /* 5,6,7,8,9,10,11,13 */ + .taa_ps = 13910, + .twr_ps = 15000, + .trcd_ps = 13910, + .trrd_ps = 6000, + .trp_ps = 13910, + .tras_ps = 34000, + .trc_ps = 48910, + .trfc_ps = 260000, + .twtr_ps = 7500, + .trtp_ps = 7500, + .refresh_rate_ps = 7800000, + .tfaw_ps = 35000, +}; + +struct board_specific_parameters { + u32 n_ranks; + u32 datarate_mhz_high; + u32 rank_gb; + u32 clk_adjust; + u32 wrlvl_start; + u32 wrlvl_ctl_2; + u32 wrlvl_ctl_3; + u32 cpo; + u32 write_data_delay; + u32 force_2t; +}; + +/* + * These tables contain all valid speeds we want to override with board + * specific parameters. datarate_mhz_high values need to be in ascending order + * for each n_ranks group. + */ + +static const struct board_specific_parameters udimm0[] = { + /* + * memory controller 0 + * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T + * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay | + */ + {2, 1066, 4, 8, 4, 0x05070609, 0x08090a08, 0xff, 2, 0}, + {2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, + {2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09, 0xff, 2, 0}, + {2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b, 0xff, 2, 0}, + {2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a, 0xff, 2, 0}, + {} +}; + +static const struct board_specific_parameters *udimms[] = { + udimm0, +}; +#endif diff --git a/board/freescale/t104xrdb/law.c b/board/freescale/t104xrdb/law.c new file mode 100644 index 0000000000..2362d4324b --- /dev/null +++ b/board/freescale/t104xrdb/law.c @@ -0,0 +1,32 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include + +struct law_entry law_table[] = { +#ifndef CONFIG_SYS_NO_FLASH + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), +#endif +#ifdef CONFIG_SYS_CPLD_BASE_PHYS + SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/t104xrdb/pci.c b/board/freescale/t104xrdb/pci.c new file mode 100644 index 0000000000..c53e3b76a4 --- /dev/null +++ b/board/freescale/t104xrdb/pci.c @@ -0,0 +1,23 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include + +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/freescale/t104xrdb/t104xrdb.c b/board/freescale/t104xrdb/t104xrdb.c new file mode 100644 index 0000000000..6e29d64107 --- /dev/null +++ b/board/freescale/t104xrdb/t104xrdb.c @@ -0,0 +1,93 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "t104xrdb.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + struct cpu_type *cpu = gd->arch.cpu; + + printf("Board: %sRDB\n", cpu->name); + return 0; +} + +int board_early_init_r(void) +{ +#ifdef CONFIG_SYS_FLASH_BASE + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); +#endif + set_liodns(); +#ifdef CONFIG_SYS_DPAA_QBMAN + setup_portals(); +#endif + + return 0; +} + +int misc_init_r(void) +{ + return 0; +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); + +#ifdef CONFIG_HAS_FSL_DR_USB + fdt_fixup_dr_usb(blob, bd); +#endif + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); +#endif +} diff --git a/board/freescale/t104xrdb/t104xrdb.h b/board/freescale/t104xrdb/t104xrdb.h new file mode 100644 index 0000000000..e7cc0c7b5e --- /dev/null +++ b/board/freescale/t104xrdb/t104xrdb.h @@ -0,0 +1,13 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __T104x_RDB_H__ +#define __T104x_RDB_H__ + +void fdt_fixup_board_enet(void *blob); +void pci_of_setup(void *blob, bd_t *bd); + +#endif diff --git a/board/freescale/t104xrdb/tlb.c b/board/freescale/t104xrdb/tlb.c new file mode 100644 index 0000000000..84f97a41e3 --- /dev/null +++ b/board/freescale/t104xrdb/tlb.c @@ -0,0 +1,107 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ +#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) + /* + * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the + * SRAM is at 0xfffc0000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256K, 1), +#else + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#endif + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + + /* *I*G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256K, 1), + + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 5, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 7, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 8, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 9, BOOKE_PAGESZ_4M, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE + /* + * *I*G - NAND + * entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so we use entry 16 for nand. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_64K, 1), +#endif +#ifdef CONFIG_SYS_CPLD_BASE + SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 11, BOOKE_PAGESZ_256K, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); -- cgit v1.2.1