From 1985abe207c4f37357b44a79dcd481602d8f83d1 Mon Sep 17 00:00:00 2001 From: Lokesh Vutla Date: Sat, 19 Sep 2015 15:00:23 +0530 Subject: ARM: keystone2: Use dtb images by default Now that OF_CONTROL is enabled on all keystone2 platforms, build the default images with DT. Signed-off-by: Lokesh Vutla --- board/ti/ks2_evm/README | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) (limited to 'board/ti') diff --git a/board/ti/ks2_evm/README b/board/ti/ks2_evm/README index b8d55e71fc..0fe5c3b9c3 100644 --- a/board/ti/ks2_evm/README +++ b/board/ti/ks2_evm/README @@ -59,8 +59,8 @@ Supported boot modes: - UART boot Supported image formats: - - u-boot.bin: for loading and running u-boot.bin through Texas instruments - code composure studio (CCS) and for UART boot. + - u-boot-dtb.bin: for loading and running u-boot-dtb.bin through + Texas Instruments code composure studio (CCS) and for UART boot. - u-boot-spi.gph: gpimage for programming SPI NOR flash for SPI NOR boot - MLO: gpimage for programming AEMIF NAND flash for NAND boot @@ -69,18 +69,18 @@ Build instructions: Examples for k2hk, for k2e and k2l just replace k2hk prefix accordingly. Don't forget to add ARCH=arm and CROSS_COMPILE. -To build u-boot.bin, u-boot-spi.gph, MLO: +To build u-boot-dtb.bin, u-boot-spi.gph, MLO: >make k2hk_evm_defconfig >make Load and Run U-Boot on keystone EVMs using CCS ========================================= -Need Code Composer Studio (CCS) installed on a PC to load and run u-boot.bin +Need Code Composer Studio (CCS) installed on a PC to load and run u-boot-dtb.bin on EVM. See instructions at below link for installing CCS on a Windows PC. http://processors.wiki.ti.com/index.php/MCSDK_UG_Chapter_Getting_Started# Installing_Code_Composer_Studio -Use u-boot.bin from the build folder for loading and running u-boot binary +Use u-boot-dtb.bin from the build folder for loading and running u-boot binary on EVM. Follow instructions at K2HK http://processors.wiki.ti.com/index.php/EVMK2H_Hardware_Setup K2E http://processors.wiki.ti.com/index.php/EVMK2E_Hardware_Setup @@ -100,7 +100,7 @@ loading the u-boot binary on the target EVM. Instead do the following:- is connected: Unknown)" at the debug window (This is created once Target configuration is launched) and select "Connect Target". 2. Once target connect is successful, choose Tools->Load Memory option from the - top level menu. At the Load Memory window, choose the file u-boot.bin + top level menu. At the Load Memory window, choose the file u-boot-dtb.bin through "Browse" button and click "next >" button. In the next window, enter Start address as 0xc001000, choose Type-size "32 bits" and click "Finish" button. @@ -167,7 +167,7 @@ Load and Run U-Boot on keystone EVMs using UART download Open BMC and regular UART terminals. -1. On the regular UART port start xmodem transfer of the u-boot.bin +1. On the regular UART port start xmodem transfer of the u-boot-dtb.bin 2. Using BMC terminal set the ARM-UART bootmode and reboot the EVM BMC> bootmode #4 MBC> reboot -- cgit v1.2.1