From 702e6014f15b307f144fa03ecaf83a8446c6802a Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Sun, 29 Apr 2012 23:57:39 +0000 Subject: doc: cleanup - move board READMEs into respective board directories Also drop a few files referring to no longer / not yet supported boards. Signed-off-by: Wolfgang Denk Cc: Prafulla Wadaskar Cc: Stefan Roese Cc: Kim Phillips Cc: Andy Fleming Cc: Jason Jin Cc: Stefano Babic Cc: Daniel Schwierzeck Acked-by: Stefano Babic Acked-by: Daniel Schwierzeck --- board/freescale/m52277evb/README | 231 ++++++++++++++++++++ board/freescale/m5253evbe/README | 103 +++++++++ board/freescale/m53017evb/README | 180 +++++++++++++++ board/freescale/m5373evb/README | 326 ++++++++++++++++++++++++++++ board/freescale/m54455evb/README | 409 +++++++++++++++++++++++++++++++++++ board/freescale/m547xevb/README | 272 +++++++++++++++++++++++ board/freescale/mpc7448hpc2/README | 184 ++++++++++++++++ board/freescale/mpc8313erdb/README | 111 ++++++++++ board/freescale/mpc8315erdb/README | 105 +++++++++ board/freescale/mpc8323erdb/README | 71 ++++++ board/freescale/mpc832xemds/README | 128 +++++++++++ board/freescale/mpc8349itx/README | 187 ++++++++++++++++ board/freescale/mpc8360emds/README | 155 +++++++++++++ board/freescale/mpc837xemds/README | 104 +++++++++ board/freescale/mpc837xerdb/README | 97 +++++++++ board/freescale/mpc8536ds/README | 127 +++++++++++ board/freescale/mpc8544ds/README | 122 +++++++++++ board/freescale/mpc8569mds/README | 77 +++++++ board/freescale/mpc8572ds/README | 166 ++++++++++++++ board/freescale/mpc8610hpcd/README | 73 +++++++ board/freescale/mpc8641hpcn/README | 186 ++++++++++++++++ board/freescale/mx35pdk/README | 188 ++++++++++++++++ board/freescale/mx6qsabrelite/README | 72 ++++++ board/freescale/p1022ds/README | 23 ++ board/freescale/p1023rds/README | 101 +++++++++ board/freescale/p1_p2_rdb/README | 145 +++++++++++++ board/freescale/p1_p2_rdb_pc/README | 46 ++++ board/freescale/p2041rdb/README | 123 +++++++++++ board/freescale/p3060qds/README | 110 ++++++++++ 29 files changed, 4222 insertions(+) create mode 100644 board/freescale/m52277evb/README create mode 100644 board/freescale/m5253evbe/README create mode 100644 board/freescale/m53017evb/README create mode 100644 board/freescale/m5373evb/README create mode 100644 board/freescale/m54455evb/README create mode 100644 board/freescale/m547xevb/README create mode 100644 board/freescale/mpc7448hpc2/README create mode 100644 board/freescale/mpc8313erdb/README create mode 100644 board/freescale/mpc8315erdb/README create mode 100644 board/freescale/mpc8323erdb/README create mode 100644 board/freescale/mpc832xemds/README create mode 100644 board/freescale/mpc8349itx/README create mode 100644 board/freescale/mpc8360emds/README create mode 100644 board/freescale/mpc837xemds/README create mode 100644 board/freescale/mpc837xerdb/README create mode 100644 board/freescale/mpc8536ds/README create mode 100644 board/freescale/mpc8544ds/README create mode 100644 board/freescale/mpc8569mds/README create mode 100644 board/freescale/mpc8572ds/README create mode 100644 board/freescale/mpc8610hpcd/README create mode 100644 board/freescale/mpc8641hpcn/README create mode 100644 board/freescale/mx35pdk/README create mode 100644 board/freescale/mx6qsabrelite/README create mode 100644 board/freescale/p1022ds/README create mode 100644 board/freescale/p1023rds/README create mode 100644 board/freescale/p1_p2_rdb/README create mode 100644 board/freescale/p1_p2_rdb_pc/README create mode 100644 board/freescale/p2041rdb/README create mode 100644 board/freescale/p3060qds/README (limited to 'board/freescale') diff --git a/board/freescale/m52277evb/README b/board/freescale/m52277evb/README new file mode 100644 index 0000000000..b6e955bcad --- /dev/null +++ b/board/freescale/m52277evb/README @@ -0,0 +1,231 @@ +Freescale MCF52277EVB ColdFire Development Board +================================================ + +TsiChung Liew(Tsi-Chung.Liew@freescale.com) +Created Jan 8, 2008 +=========================================== + + +Changed files: +============== + +- board/freescale/m52277evb/m52277evb.c Dram setup +- board/freescale/m52277evb/Makefile Makefile +- board/freescale/m52277evb/config.mk config make +- board/freescale/m52277evb/u-boot.lds Linker description + +- arch/m68k/cpu/mcf5227x/cpu.c cpu specific code +- arch/m68k/cpu/mcf5227x/cpu_init.c FBCS, Mux pins, icache and RTC extra regs +- arch/m68k/cpu/mcf5227x/interrupts.c cpu specific interrupt support +- arch/m68k/cpu/mcf5227x/speed.c system, flexbus, and cpu clock +- arch/m68k/cpu/mcf5227x/Makefile Makefile +- arch/m68k/cpu/mcf5227x/config.mk config make +- arch/m68k/cpu/mcf5227x/start.S start up assembly code + +- doc/README.m52277evb This readme file + +- drivers/serial/mcfuart.c ColdFire common UART driver +- drivers/rtc/mcfrtc.c Realtime clock Driver + +- include/asm-m68k/bitops.h Bit operation function export +- include/asm-m68k/byteorder.h Byte order functions +- include/asm-m68k/crossbar.h CrossBar structure and definition +- include/asm-m68k/dspi.h DSPI structure and definition +- include/asm-m68k/edma.h eDMA structure and definition +- include/asm-m68k/flexbus.h FlexBus structure and definition +- include/asm-m68k/fsl_i2c.h I2C structure and definition +- include/asm-m68k/global_data.h Global data structure +- include/asm-m68k/immap.h ColdFire specific header file and driver macros +- include/asm-m68k/immap_5227x.h mcf5227x specific header file +- include/asm-m68k/io.h io functions +- include/asm-m68k/lcd.h LCD structure and definition +- include/asm-m68k/m5227x.h mcf5227x specific header file +- include/asm-m68k/posix_types.h Posix +- include/asm-m68k/processor.h header file +- include/asm-m68k/ptrace.h Exception structure +- include/asm-m68k/rtc.h Realtime clock header file +- include/asm-m68k/ssi.h SSI structure and definition +- include/asm-m68k/string.h String function export +- include/asm-m68k/timer.h Timer structure and definition +- include/asm-m68k/types.h Data types definition +- include/asm-m68k/uart.h Uart structure and definition +- include/asm-m68k/u-boot.h u-boot structure + +- include/configs/M52277EVB.h Board specific configuration file + +- arch/m68k/lib/board.c board init function +- arch/m68k/lib/cache.c +- arch/m68k/lib/interrupts Coldfire common interrupt functions +- arch/m68k/lib/m68k_linux.c +- arch/m68k/lib/time.c Timer functions (Dma timer and PIT) +- arch/m68k/lib/traps.c Exception init code + +1 MCF52277 specific Options/Settings +==================================== +1.1 pre-loader is no longer suppoer in this coldfire family + +1.2 Configuration settings for M52277EVB Development Board +CONFIG_MCF5227x -- define for all MCF5227x CPUs +CONFIG_M52277 -- define for all Freescale MCF52277 CPUs +CONFIG_M52277EVB -- define for M52277EVB board + +CONFIG_MCFUART -- define to use common CF Uart driver +CONFIG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2 +CONFIG_BAUDRATE -- define UART baudrate + +CONFIG_MCFRTC -- define to use common CF RTC driver +CONFIG_SYS_MCFRTC_BASE -- provide base address for RTC in immap.h +CONFIG_SYS_RTC_OSCILLATOR -- define RTC clock frequency +RTC_DEBUG -- define to show RTC debug message +CONFIG_CMD_DATE -- enable to use date feature in u-boot + +CONFIG_MCFTMR -- define to use DMA timer +CONFIG_MCFPIT -- define to use PIT timer + +CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_HARD_I2C -- define for I2C hardware support +CONFIG_SOFT_I2C -- define for I2C bit-banged +CONFIG_SYS_I2C_SPEED -- define for I2C speed +CONFIG_SYS_I2C_SLAVE -- define for I2C slave address +CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset +CONFIG_SYS_IMMR -- define for MBAR offset + +CONFIG_SYS_MBAR -- define MBAR offset + +CONFIG_MONITOR_IS_IN_RAM -- Not support + +CONFIG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF52277 internal SRAM + +CONFIG_SYS_CSn_BASE -- defines the Chip Select Base register +CONFIG_SYS_CSn_MASK -- defines the Chip Select Mask register +CONFIG_SYS_CSn_CTRL -- defines the Chip Select Control register + +CONFIG_SYS_SDRAM_BASE -- defines the DRAM Base + +CONFIG_LCD and CONFIG_CMD_USB are not supported in this current u-boot, +update will be provided at later time + +2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL +=========================================== +2.1. System memory map: + Flash: 0x00000000-0x3FFFFFFF (1024MB) + DDR: 0x40000000-0x7FFFFFFF (1024MB) + SRAM: 0x80000000-0x8FFFFFFF (256MB) + IP: 0xF0000000-0xFFFFFFFF (256MB) + +2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and + linux kernel, you can customize it based on your system requirements: + Flash0: 0x00000000-0x00FFFFFF (16MB) + + DDR: 0x40000000-0x4FFFFFFF (64MB) + SRAM: 0x80000000-0x80007FFF (32KB) + IP: 0xFC000000-0xFC0FFFFF (64KB) + +3. COMPILATION +============== +3.1 To create U-Boot the gcc-4.1-xx compiler set (ColdFire ELF or +uClinux version) from codesourcery.com was used. Download it from: +http://www.codesourcery.com/gnu_toolchains/coldfire/download.html + +3.2 Compilation + export CROSS_COMPILE=cross-compile-prefix + cd u-boot-1.x.x + make distclean + make M52277EVB_config + make + +4. SCREEN DUMP +============== +4.1 M52277EVB Development board + (NOTE: May not show exactly the same) + +U-Boot 1.3.1 (Jan 8 2008 - 12:44:08) + +CPU: Freescale MCF52277 (Mask:6c Version:0) + CPU CLK 160 Mhz BUS CLK 80 Mhz FLB CLK 80 MHZ + INP CLK 16 Mhz VCO CLK 480 Mhz +Board: Freescale 52277 EVB +I2C: ready +DRAM: 64 MB +FLASH: 16 MB +In: serial +Out: serial +Err: serial +-> print +baudrate=115200 +hostname=M52277EVB +inpclk=16000000 +loadaddr=(0x40000000 + 0x10000) +load=tftp ${loadaddr) ${u-boot} +upd=run load; run prog +prog=prot off 0 3ffff;era 0 3ffff;cp.b ${loadaddr} 0 ${filesize};save +u-boot=u-boot.bin +stdin=serial +stdout=serial +stderr=serial +mem=65024k + +Environment size: 280/32764 bytes +-> bdinfo +memstart = 0x40000000 +memsize = 0x04000000 +flashstart = 0x00000000 +flashsize = 0x01000000 +flashoffset = 0x00000000 +sramstart = 0x80000000 +sramsize = 0x00008000 +mbar = 0xFC000000 +busfreq = 80 MHz +flbfreq = 80 Mhz +inpfreq = 16 Mhz +vcofreq = 480 Mhz + +baudrate = 115200 bps +-> +-> help +? - alias for 'help' +base - print or set address offset +bdinfo - print Board Info structure +boot - boot default, i.e., run 'bootcmd' +bootd - boot default, i.e., run 'bootcmd' +bootelf - Boot from an ELF image in memory +bootm - boot application image from memory +bootp - boot image via network using BootP/TFTP protocol +bootvx - Boot vxWorks from an ELF image +cmp - memory compare +coninfo - print console devices and information +cp - memory copy +crc32 - checksum calculation +date - get/set/reset date & time +dcache - enable or disable data cache +echo - echo args to console +erase - erase FLASH memory +flinfo - print FLASH memory information +go - start application at address 'addr' +help - print online help +i2c - I2C sub-system +icache - enable or disable instruction cache +iminfo - print header information for application image +imls - list all images found in flash +itest - return true/false on integer compare +loadb - load binary file over serial line (kermit mode) +loads - load S-Record file over serial line +loady - load binary file over serial line (ymodem mode) +loop - infinite loop on address range +ls - list files in a directory (default /) +md - memory display +mm - memory modify (auto-incrementing) +mtest - simple RAM test +mw - memory write (fill) +nm - memory modify (constant address) +ping - send ICMP ECHO_REQUEST to network host +printenv- print environment variables +protect - enable or disable FLASH write protection +reset - Perform RESET of the CPU +run - run commands in an environment variable +saveenv - save environment variables to persistent storage +setenv - set environment variables +sleep - delay execution for some time +source - run script from memory +version - print monitor version +-> diff --git a/board/freescale/m5253evbe/README b/board/freescale/m5253evbe/README new file mode 100644 index 0000000000..f51609f3e0 --- /dev/null +++ b/board/freescale/m5253evbe/README @@ -0,0 +1,103 @@ +Freescale Amadeus Plus M5253EVBE board +====================================== + +Hayden Fraser(Hayden.Fraser@freescale.com) +Created 06/05/2007 +=========================================== + + +1. SWITCH SETTINGS +================== +1.1 N/A + + +2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL +=========================================== +2.1. For the initial bringup, we adopted a consistent memory scheme between u-boot and + linux kernel, you can customize it based on your system requirements: + SDR: 0x00000000-0x00ffffff + SRAM0: 0x20010000-0x20017fff + SRAM1: 0x20000000-0x2000ffff + MBAR1: 0x10000000-0x4fffffff + MBAR2: 0x80000000-0xCfffffff + Flash: 0xffe00000-0xffffffff + +3. DEFINITIONS AND COMPILATION +============================== +3.1 Explanation on NEW definitions in include/configs/M5253EVBE.h + CONFIG_MCF52x2 Processor family + CONFIG_MCF5253 MCF5253 specific + CONFIG_M5253EVBE Amadeus Plus board specific + CONFIG_SYS_CLK Define Amadeus Plus CPU Clock + CONFIG_SYS_MBAR MBAR base address + CONFIG_SYS_MBAR2 MBAR2 base address + +3.2 Compilation + export CROSS_COMPILE=/usr/local/freescale-coldfire-4.1-elf/bin/m68k-elf- + cd u-boot-1-2-x + make distclean + make M5253EVBE_config + make + + +4. SCREEN DUMP +============== +4.1 U-Boot 1.2.0 (Jun 18 2007 - 18:20:00) + +CPU: Freescale Coldfire MCF5253 at 62 MHz +Board: Freescale MCF5253 EVBE +DRAM: 16 MB +FLASH: 2 MB +In: serial +Out: serial +Err: serial +=> flinfo + +Bank # 1: CFI conformant FLASH (16 x 16) Size: 2 MB in 35 Sectors + AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x49 + Erase timeout: 16384 ms, write timeout: 1 ms + + Sector Start Addresses: + FFE00000 RO FFE04000 RO FFE06000 RO FFE08000 RO FFE10000 RO + FFE20000 FFE30000 FFE40000 FFE50000 FFE60000 + FFE70000 FFE80000 FFE90000 FFEA0000 FFEB0000 + FFEC0000 FFED0000 FFEE0000 FFEF0000 FFF00000 + FFF10000 FFF20000 FFF30000 FFF40000 FFF50000 + FFF60000 FFF70000 FFF80000 FFF90000 FFFA0000 + FFFB0000 FFFC0000 FFFD0000 FFFE0000 FFFF0000 + +=> bdinfo +boot_params = 0x00F62F90 +memstart = 0x00000000 +memsize = 0x01000000 +flashstart = 0xFFE00000 +flashsize = 0x00200000 +flashoffset = 0x00000000 +baudrate = 19200 bps + +=> printenv +bootdelay=5 +baudrate=19200 +stdin=serial +stdout=serial +stderr=serial + +Environment size: 134/8188 bytes +=> saveenv +Saving Environment to Flash... +Un-Protected 1 sectors +Erasing Flash... +. done +Erased 1 sectors +Writing to Flash... done +Protected 1 sectors +=> + +5. COMPILER +----------- +To create U-Boot the CodeSourcery's version of the GNU Toolchain for the ColdFire architecture +compiler set (freescale-coldfire-4.1-elf) from www.codesourcery.com was used. +You can download it from:http://www.codesourcery.com/gnu_toolchains/coldfire/download.html + +compiler that you used - for example, codesourcery_elf requires -MQ in rules.mk, old M68K 2.95.3 just -M +codesourcery_elf requires -MQ in rules.mk, old M68K 2.95.3 just -M diff --git a/board/freescale/m53017evb/README b/board/freescale/m53017evb/README new file mode 100644 index 0000000000..64a3d42f0c --- /dev/null +++ b/board/freescale/m53017evb/README @@ -0,0 +1,180 @@ +Freescale MCF53017EVB ColdFire Development Board +================================================ + +TsiChung Liew(Tsi-Chung.Liew@freescale.com) +Created 10/22/08 +=========================================== + + +Changed files: +============== + +- board/freescale/m53017evb/m53017evb.c Dram setup +- board/freescale/m53017evb/mii.c Mii access +- board/freescale/m53017evb/Makefile Makefile +- board/freescale/m53017evb/config.mk config make +- board/freescale/m53017evb/u-boot.lds Linker description + +- arch/m68k/cpu/mcf532x/cpu.c cpu specific code +- arch/m68k/cpu/mcf532x/cpu_init.c FBCS, Mux pins, icache and RTC extra regs +- arch/m68k/cpu/mcf532x/interrupts.c cpu specific interrupt support +- arch/m68k/cpu/mcf532x/speed.c system, flexbus, and cpu clock +- arch/m68k/cpu/mcf532x/Makefile Makefile +- arch/m68k/cpu/mcf532x/config.mk config make +- arch/m68k/cpu/mcf532x/start.S start up assembly code + +- doc/README.m53017evb This readme file + +- drivers/net/mcffec.c ColdFire common FEC driver +- drivers/net/mcfmii.c ColdFire common Mii driver +- drivers/serial/mcfuart.c ColdFire common UART driver +- drivers/rtc/mcfrtc.c Realtime clock Driver + +- include/asm-m68k/bitops.h Bit operation function export +- include/asm-m68k/byteorder.h Byte order functions +- include/asm-m68k/fec.h FEC structure and definition +- include/asm-m68k/fsl_i2c.h I2C structure and definition +- include/asm-m68k/global_data.h Global data structure +- include/asm-m68k/immap.h ColdFire specific header file and driver macros +- include/asm-m68k/immap_5301x.h mcf5301x specific header file +- include/asm-m68k/io.h io functions +- include/asm-m68k/m532x.h mcf5301x specific header file +- include/asm-m68k/posix_types.h Posix +- include/asm-m68k/processor.h header file +- include/asm-m68k/ptrace.h Exception structure +- include/asm-m68k/rtc.h Realtime clock header file +- include/asm-m68k/string.h String function export +- include/asm-m68k/timer.h Timer structure and definition +- include/asm-m68k/types.h Data types definition +- include/asm-m68k/uart.h Uart structure and definition +- include/asm-m68k/u-boot.h u-boot structure + +- include/configs/M53017EVB.h Board specific configuration file + +- arch/m68k/lib/board.c board init function +- arch/m68k/lib/cache.c +- arch/m68k/lib/interrupts Coldfire common interrupt functions +- arch/m68k/lib/m68k_linux.c +- arch/m68k/lib/time.c Timer functions (Dma timer and PIT) +- arch/m68k/lib/traps.c Exception init code + +1 MCF5301x specific Options/Settings +==================================== +1.1 pre-loader is no longer suppoer in thie coldfire family + +1.2 Configuration settings for M53017EVB Development Board +CONFIG_MCF5301x -- define for all MCF5301x CPUs +CONFIG_M53015 -- define for MCF53015 CPUs +CONFIG_M53017EVB -- define for M53017EVB board + +CONFIG_MCFUART -- define to use common CF Uart driver +CONFIG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2 +CONFIG_BAUDRATE -- define UART baudrate + +CONFIG_MCFRTC -- define to use common CF RTC driver +CONFIG_SYS_MCFRTC_BASE -- provide base address for RTC in immap.h +CONFIG_SYS_RTC_OSCILLATOR -- define RTC clock frequency +RTC_DEBUG -- define to show RTC debug message +CONFIG_CMD_DATE -- enable to use date feature in u-boot + +CONFIG_MCFFEC -- define to use common CF FEC driver +CONFIG_MII -- enable to use MII driver +CONFIG_CF_DOMII -- enable to use MII feature in cmd_mii.c +CONFIG_SYS_DISCOVER_PHY -- enable PHY discovery +CONFIG_SYS_RX_ETH_BUFFER -- Set FEC Receive buffer +CONFIG_SYS_FAULT_ECHO_LINK_DOWN -- +CONFIG_SYS_FEC0_PINMUX -- Set FEC0 Pin configuration +CONFIG_SYS_FEC0_MIIBASE -- Set FEC0 MII base register +MCFFEC_TOUT_LOOP -- set FEC timeout loop + +CONFIG_MCFTMR -- define to use DMA timer +CONFIG_MCFPIT -- define to use PIT timer + +CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_HARD_I2C -- define for I2C hardware support +CONFIG_SOFT_I2C -- define for I2C bit-banged +CONFIG_SYS_I2C_SPEED -- define for I2C speed +CONFIG_SYS_I2C_SLAVE -- define for I2C slave address +CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset +CONFIG_SYS_IMMR -- define for MBAR offset + +CONFIG_SYS_MBAR -- define MBAR offset + +CONFIG_MONITOR_IS_IN_RAM -- Not support + +CONFIG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF5301x internal SRAM + +CONFIG_SYS_CSn_BASE -- defines the Chip Select Base register +CONFIG_SYS_CSn_MASK -- defines the Chip Select Mask register +CONFIG_SYS_CSn_CTRL -- defines the Chip Select Control register + +CONFIG_SYS_SDRAM_BASE -- defines the DRAM Base + +2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL +=========================================== +2.1. System memory map: + Flash: 0x00000000-0x3FFFFFFF (1024MB) + DDR: 0x40000000-0x7FFFFFFF (1024MB) + SRAM: 0x80000000-0x8FFFFFFF (256MB) + IP: 0xFC000000-0xFFFFFFFF (256MB) + +2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and + linux kernel, you can customize it based on your system requirements: + Flash0: 0x00000000-0x00FFFFFF (16MB) + DDR: 0x40000000-0x4FFFFFFF (256MB) + SRAM: 0x80000000-0x80007FFF (32KB) + IP: 0xFC000000-0xFC0FFFFF (64KB) + +3. COMPILATION +============== +3.1 To create U-Boot the gcc-4.x-xx compiler set (ColdFire ELF or +uClinux version) from codesourcery.com was used. Download it from: +http://www.codesourcery.com/gnu_toolchains/coldfire/download.html + +3.2 Compilation + export CROSS_COMPILE=cross-compile-prefix + cd u-boot + make distclean + make M53017EVB_config + make + +4. SCREEN DUMP +============== +4.1 M53017EVB Development board + (NOTE: May not show exactly the same) + +U-Boot 2008.10 (Oct 22 2007 - 11:07:57) + +CPU: Freescale MCF53015 (Mask:76 Version:0) + CPU CLK 240 Mhz BUS CLK 80 Mhz +Board: Freescale M53017EVB +I2C: ready +DRAM: 64 MB +FLASH: 16 MB +In: serial +Out: serial +Err: serial +NAND: 16 MiB +Net: FEC0, FEC1 +-> print +bootdelay=1 +baudrate=115200 +ethaddr=00:e0:0c:bc:e5:60 +hostname=M53017EVB +netdev=eth0 +loadaddr=40010000 +u-boot=u-boot.bin +load=tftp ${loadaddr) ${u-boot} +upd=run load; run prog +prog=prot off 0 3ffff;era 0 3ffff;cp.b ${loadaddr} 0 ${filesize};save +gatewayip=192.168.1.1 +netmask=255.255.255.0 +ipaddr=192.168.1.3 +serverip=192.168.1.2 +stdin=serial +stdout=serial +stderr=serial +mem=65024k + +Environment size: 437/4092 bytes +-> diff --git a/board/freescale/m5373evb/README b/board/freescale/m5373evb/README new file mode 100644 index 0000000000..419d4d6d1e --- /dev/null +++ b/board/freescale/m5373evb/README @@ -0,0 +1,326 @@ +Freescale MCF5373EVB ColdFire Development Board +================================================ + +TsiChung Liew(Tsi-Chung.Liew@freescale.com) +Created 11/08/07 +=========================================== + + +Changed files: +============== + +- board/freescale/m5373evb/m5373evb.c Dram setup +- board/freescale/m5373evb/mii.c Mii access +- board/freescale/m5373evb/Makefile Makefile +- board/freescale/m5373evb/config.mk config make +- board/freescale/m5373evb/u-boot.lds Linker description + +- arch/m68k/cpu/mcf532x/cpu.c cpu specific code +- arch/m68k/cpu/mcf532x/cpu_init.c FBCS, Mux pins, icache and RTC extra regs +- arch/m68k/cpu/mcf532x/interrupts.c cpu specific interrupt support +- arch/m68k/cpu/mcf532x/speed.c system, pci, flexbus, and cpu clock +- arch/m68k/cpu/mcf532x/Makefile Makefile +- arch/m68k/cpu/mcf532x/config.mk config make +- arch/m68k/cpu/mcf532x/start.S start up assembly code + +- doc/README.m5373evb This readme file + +- drivers/net/mcffec.c ColdFire common FEC driver +- drivers/serial/mcfuart.c ColdFire common UART driver +- drivers/rtc/mcfrtc.c Realtime clock Driver + +- include/asm-m68k/bitops.h Bit operation function export +- include/asm-m68k/byteorder.h Byte order functions +- include/asm-m68k/fec.h FEC structure and definition +- include/asm-m68k/fsl_i2c.h I2C structure and definition +- include/asm-m68k/global_data.h Global data structure +- include/asm-m68k/immap.h ColdFire specific header file and driver macros +- include/asm-m68k/immap_532x.h mcf532x specific header file +- include/asm-m68k/io.h io functions +- include/asm-m68k/m532x.h mcf532x specific header file +- include/asm-m68k/posix_types.h Posix +- include/asm-m68k/processor.h header file +- include/asm-m68k/ptrace.h Exception structure +- include/asm-m68k/rtc.h Realtime clock header file +- include/asm-m68k/string.h String function export +- include/asm-m68k/timer.h Timer structure and definition +- include/asm-m68k/types.h Data types definition +- include/asm-m68k/uart.h Uart structure and definition +- include/asm-m68k/u-boot.h u-boot structure + +- include/configs/M5373EVB.h Board specific configuration file + +- arch/m68k/lib/board.c board init function +- arch/m68k/lib/cache.c +- arch/m68k/lib/interrupts Coldfire common interrupt functions +- arch/m68k/lib/m68k_linux.c +- arch/m68k/lib/time.c Timer functions (Dma timer and PIT) +- arch/m68k/lib/traps.c Exception init code + +1 MCF5373 specific Options/Settings +==================================== +1.1 pre-loader is no longer suppoer in thie coldfire family + +1.2 Configuration settings for M5373EVB Development Board +CONFIG_MCF532x -- define for all MCF532x CPUs +CONFIG_M5373 -- define for all Freescale MCF5373 CPUs +CONFIG_M5373EVB -- define for M5373EVB board + +CONFIG_MCFUART -- define to use common CF Uart driver +CONFIG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2 +CONFIG_BAUDRATE -- define UART baudrate + +CONFIG_MCFRTC -- define to use common CF RTC driver +CONFIG_SYS_MCFRTC_BASE -- provide base address for RTC in immap.h +CONFIG_SYS_RTC_OSCILLATOR -- define RTC clock frequency +RTC_DEBUG -- define to show RTC debug message +CONFIG_CMD_DATE -- enable to use date feature in u-boot + +CONFIG_MCFFEC -- define to use common CF FEC driver +CONFIG_MII -- enable to use MII driver +CONFIG_CF_DOMII -- enable to use MII feature in cmd_mii.c +CONFIG_SYS_DISCOVER_PHY -- enable PHY discovery +CONFIG_SYS_RX_ETH_BUFFER -- Set FEC Receive buffer +CONFIG_SYS_FAULT_ECHO_LINK_DOWN-- +CONFIG_SYS_FEC0_PINMUX -- Set FEC0 Pin configuration +CONFIG_SYS_FEC0_MIIBASE -- Set FEC0 MII base register +MCFFEC_TOUT_LOOP -- set FEC timeout loop + +CONFIG_MCFTMR -- define to use DMA timer +CONFIG_MCFPIT -- define to use PIT timer + +CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_HARD_I2C -- define for I2C hardware support +CONFIG_SOFT_I2C -- define for I2C bit-banged +CONFIG_SYS_I2C_SPEED -- define for I2C speed +CONFIG_SYS_I2C_SLAVE -- define for I2C slave address +CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset +CONFIG_SYS_IMMR -- define for MBAR offset + +CONFIG_SYS_MBAR -- define MBAR offset + +CONFIG_MONITOR_IS_IN_RAM -- Not support + +CONFIG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF5373 internal SRAM + +CONFIG_SYS_CSn_BASE -- defines the Chip Select Base register +CONFIG_SYS_CSn_MASK -- defines the Chip Select Mask register +CONFIG_SYS_CSn_CTRL -- defines the Chip Select Control register + +CONFIG_SYS_SDRAM_BASE -- defines the DRAM Base + +2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL +=========================================== +2.1. System memory map: + Flash: 0x00000000-0x3FFFFFFF (1024MB) + DDR: 0x40000000-0x7FFFFFFF (1024MB) + SRAM: 0x80000000-0x8FFFFFFF (256MB) + IP: 0xF0000000-0xFFFFFFFF (256MB) + +2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and + linux kernel, you can customize it based on your system requirements: + Flash0: 0x00000000-0x00FFFFFF (16MB) + + DDR: 0x40000000-0x4FFFFFFF (256MB) + SRAM: 0x80000000-0x80007FFF (32KB) + IP: 0xFC000000-0xFC0FFFFF (64KB) + +3. COMPILATION +============== +3.1 To create U-Boot the gcc-4.1-xx compiler set (ColdFire ELF or +uClinux version) from codesourcery.com was used. Download it from: +http://www.codesourcery.com/gnu_toolchains/coldfire/download.html + +3.2 Compilation + export CROSS_COMPILE=cross-compile-prefix + cd u-boot-1.x.x + make distclean + make M5373EVB_config + make + +4. SCREEN DUMP +============== +4.1 M5373EVB Development board + (NOTE: May not show exactly the same) + +U-Boot 1.3.0 (Nov 8 2007 - 12:44:08) + +CPU: Freescale MCF5373 (Mask:65 Version:1) + CPU CLK 240 Mhz BUS CLK 80 Mhz +Board: Freescale FireEngine 5373 EVB +I2C: ready +DRAM: 32 MB +FLASH: 2 MB +In: serial +Out: serial +Err: serial +NAND: 16 MiB +Net: FEC0 +-> print +bootdelay=1 +baudrate=115200 +ethaddr=00:e0:0c:bc:e5:60 +hostname=M5373EVB +netdev=eth0 +loadaddr=40010000 +load=tftp ${loadaddr) ${u-boot} +upd=run load; run prog +prog=prot off 0 2ffff;era 0 2ffff;cp.b ${loadaddr} 0 ${filesize};save +ethact=FEC0 +u-boot=u-boot.bin +gatewayip=192.168.1.1 +netmask=255.255.255.0 +ipaddr=192.168.1.3 +serverip=192.168.1.2 +stdin=serial +stdout=serial +stderr=serial +mem=261632k + +Environment size: 401/8188 bytes +-> bdinfo +memstart = 0x40000000 +memsize = 0x02000000 +flashstart = 0x00000000 +flashsize = 0x00200000 +flashoffset = 0x00000000 +sramstart = 0x80000000 +sramsize = 0x00008000 +mbar = 0xFC000000 +busfreq = 80 MHz +ethaddr = 00:E0:0C:BC:E5:60 +ip_addr = 192.168.1.3 +baudrate = 115200 bps +-> +-> help +? - alias for 'help' +base - print or set address offset +bdinfo - print Board Info structure +boot - boot default, i.e., run 'bootcmd' +bootd - boot default, i.e., run 'bootcmd' +bootelf - Boot from an ELF image in memory +bootm - boot application image from memory +bootp - boot image via network using BootP/TFTP protocol +bootvx - Boot vxWorks from an ELF image +cmp - memory compare +coninfo - print console devices and information +cp - memory copy +crc32 - checksum calculation +date - get/set/reset date & time +dcache - enable or disable data cache +echo - echo args to console +erase - erase FLASH memory +flinfo - print FLASH memory information +go - start application at address 'addr' +help - print online help +i2c - I2C sub-system +icache - enable or disable instruction cache +iminfo - print header information for application image +imls - list all images found in flash +itest - return true/false on integer compare +loadb - load binary file over serial line (kermit mode) +loads - load S-Record file over serial line +loady - load binary file over serial line (ymodem mode) +loop - infinite loop on address range +ls - list files in a directory (default /) +md - memory display +mii - MII utility commands +mm - memory modify (auto-incrementing) +mtest - simple RAM test +mw - memory write (fill) +nand - NAND sub-system +nboot - boot from NAND device +nfs - boot image via network using NFS protocol +nm - memory modify (constant address) +ping - send ICMP ECHO_REQUEST to network host +printenv- print environment variables +protect - enable or disable FLASH write protection +rarpboot- boot image via network using RARP/TFTP protocol +reset - Perform RESET of the CPU +run - run commands in an environment variable +saveenv - save environment variables to persistent storage +setenv - set environment variables +sleep - delay execution for some time +source - run script from memory +tftpboot- boot image via network using TFTP protocol +version - print monitor version +-> tftp 0x40800000 uImage +Using FEC0 device +TFTP from server 192.168.1.3; our IP address is 192.168.1.3 Filename 'uImage'. +Load address: 0x40800000 +Loading: ################################################################# + ################################################################# + ########## +done +Bytes transferred = 2053270 (1f5496 hex) +-> bootm 0x40800000 +## Booting image at 40800000 ... + Image Name: Linux Kernel Image + Created: 2007-11-07 20:33:08 UTC + Image Type: M68K Linux Kernel Image (gzip compressed) + Data Size: 2053206 Bytes = 2 MB + Load Address: 40020000 + Entry Point: 40020000 + Verifying Checksum ... OK + Uncompressing Kernel Image ... OK +Linux version 2.6.22-uc1 (mattw@loa) (gcc version 4.2.1 (Sourcery G++ Lite 4.2-7 + + +uClinux/COLDFIRE(m537x) +COLDFIRE port done by Greg Ungerer, gerg@snapgear.com Flat model support (C) 1998,1999 Kenneth Albanowski, D. Jeff Dionne Built 1 zonelists. Total pages: 8128 Kernel command line: rootfstype=romfs PID hash table entries: 128 (order: 7, 512 bytes) Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory available: 28092k/32768k RAM, (1788k kernel code, 244k data) Mount-cache hash table entries: 512 +NET: Registered protocol family 16 +USB-MCF537x: (HOST module) EHCI device is registered +USB-MCF537x: (OTG module) EHCI device is registered +USB-MCF537x: (OTG module) UDC device is registered +usbcore: registered new interface driver usbfs +usbcore: registered new interface driver hub +usbcore: registered new device driver usb +NET: Registered protocol family 2 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) +TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered +JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. +io scheduler noop registered +io scheduler cfq registered (default) +ColdFire internal UART serial driver version 1.00 ttyS0 at 0xfc060000 (irq = 90) is a builtin ColdFire UART +ttyS1 at 0xfc064000 (irq = 91) is a builtin ColdFire UART +ttyS2 at 0xfc068000 (irq = 92) is a builtin ColdFire UART RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize +loop: module loaded +nbd: registered device at major 43 +usbcore: registered new interface driver ub FEC ENET Version 0.2 +fec: PHY @ 0x1, ID 0x20005c90 -- DP83848 +eth0: ethernet 00:e0:0c:bc:e5:60 +uclinux[mtd]: RAM probe address=0x4021c22c size=0x22b000 Creating 1 MTD partitions on "RAM": +0x00000000-0x0022b000 : "ROMfs" +uclinux[mtd]: set ROMfs to be root filesystem NAND device: Manufacturer ID: 0x20, Chip ID: 0x73 (ST Micro NAND 16MiB 3,3V 8-b) Scanning device for bad blocks Creating 1 MTD partitions on "NAND 16MiB 3,3V 8-bit": +0x00000000-0x01000000 : "M53xx flash partition 1" +QSPI: spi->max_speed_hz 300000 +QSPI: Baud set to 255 +SPI: Coldfire master initialized +M537x - Disable UART1 when using Audio +udc: Freescale MCF53xx UDC driver version 27 October 2006 init +udc: MCF53xx USB Device is found. ID=0x5 Rev=0x41 i2c /dev entries driver +usbcore: registered new interface driver usbhid +drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered +NET: Registered protocol family 1 +NET: Registered protocol family 17 +VFS: Mounted root (romfs filesystem) readonly. +Freeing unused kernel memory: 64k freed (0x401f5000 - 0x40204000) init started: BusyBox v1.00 (2007.11.07-19:57+0000) multi-call binary?Setting e Mounting filesystems +mount: Mounting devpts on /dev/pts failed: No such device +mount: Mounting usbfs on /proc/bus/usb failed: No such file or directory Starting syslogd and klogd Setting up networking on loopback device: +Setting up networking on eth0: +info, udhcpc (v0.9.9-pre) started +eth0: config: auto-negotiation on, 100FDX, 100HDX, 10FDX, 10HDX. +debug, Sending discover... +debug, Sending discover... +debug, Sending select for 172.27.0.130... +info, Lease of 172.27.0.130 obtained, lease time 43200 deleting routers +route: SIOC[ADD|DEL]RT: No such process +adding dns 172.27.0.1 +Starting the boa webserver: +Setting time from ntp server: ntp.cs.strath.ac.uk +ntp.cs.strath.ac.uk: Unknown host + + +BusyBox v1.00 (2007.11.07-19:57+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. + +# diff --git a/board/freescale/m54455evb/README b/board/freescale/m54455evb/README new file mode 100644 index 0000000000..2bc6ce4bf3 --- /dev/null +++ b/board/freescale/m54455evb/README @@ -0,0 +1,409 @@ +Freescale MCF54455EVB ColdFire Development Board +================================================ + +TsiChung Liew(Tsi-Chung.Liew@freescale.com) +Created 4/08/07 +=========================================== + + +Changed files: +============== + +- board/freescale/m54455evb/m54455evb.c Dram setup, IDE pre init, and PCI init +- board/freescale/m54455evb/flash.c Atmel and INTEL flash support +- board/freescale/m54455evb/Makefile Makefile +- board/freescale/m54455evb/config.mk config make +- board/freescale/m54455evb/u-boot.lds Linker description + +- common/cmd_bdinfo.c Clock frequencies output +- common/cmd_mii.c mii support + +- arch/m68k/cpu/mcf5445x/cpu.c cpu specific code +- arch/m68k/cpu/mcf5445x/cpu_init.c Flexbus ChipSelect, Mux pins setup, icache and RTC extra regs +- arch/m68k/cpu/mcf5445x/interrupts.c cpu specific interrupt support +- arch/m68k/cpu/mcf5445x/speed.c system, pci, flexbus, and cpu clock +- arch/m68k/cpu/mcf5445x/Makefile Makefile +- arch/m68k/cpu/mcf5445x/config.mk config make +- arch/m68k/cpu/mcf5445x/start.S start up assembly code + +- doc/README.m54455evb This readme file + +- drivers/net/mcffec.c ColdFire common FEC driver +- drivers/serial/mcfuart.c ColdFire common UART driver + +- include/asm-m68k/bitops.h Bit operation function export +- include/asm-m68k/byteorder.h Byte order functions +- include/asm-m68k/fec.h FEC structure and definition +- include/asm-m68k/fsl_i2c.h I2C structure and definition +- include/asm-m68k/global_data.h Global data structure +- include/asm-m68k/immap.h ColdFire specific header file and driver macros +- include/asm-m68k/immap_5445x.h mcf5445x specific header file +- include/asm-m68k/io.h io functions +- include/asm-m68k/m5445x.h mcf5445x specific header file +- include/asm-m68k/posix_types.h Posix +- include/asm-m68k/processor.h header file +- include/asm-m68k/ptrace.h Exception structure +- include/asm-m68k/rtc.h Realtime clock header file +- include/asm-m68k/string.h String function export +- include/asm-m68k/timer.h Timer structure and definition +- include/asm-m68k/types.h Data types definition +- include/asm-m68k/uart.h Uart structure and definition +- include/asm-m68k/u-boot.h u-boot structure + +- include/configs/M54455EVB.h Board specific configuration file + +- arch/m68k/lib/board.c board init function +- arch/m68k/lib/cache.c +- arch/m68k/lib/interrupts Coldfire common interrupt functions +- arch/m68k/lib/m68k_linux.c +- arch/m68k/lib/time.c Timer functions (Dma timer and PIT) +- arch/m68k/lib/traps.c Exception init code + +- rtc/mcfrtc.c Realtime clock Driver + +1 MCF5445x specific Options/Settings +==================================== +1.1 pre-loader is no longer suppoer in thie coldfire family + +1.2 Configuration settings for M54455EVB Development Board +CONFIG_MCF5445x -- define for all MCF5445x CPUs +CONFIG_M54455 -- define for all Freescale MCF54455 CPUs +CONFIG_M54455EVB -- define for M54455EVB board + +CONFIG_MCFUART -- define to use common CF Uart driver +CONFIG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2 +CONFIG_BAUDRATE -- define UART baudrate + +CONFIG_MCFRTC -- define to use common CF RTC driver +CONFIG_SYS_MCFRTC_BASE -- provide base address for RTC in immap.h +CONFIG_SYS_RTC_OSCILLATOR -- define RTC clock frequency +RTC_DEBUG -- define to show RTC debug message +CONFIG_CMD_DATE -- enable to use date feature in u-boot + +CONFIG_MCFFEC -- define to use common CF FEC driver +CONFIG_MII -- enable to use MII driver +CONFIG_CF_DOMII -- enable to use MII feature in cmd_mii.c +CONFIG_SYS_DISCOVER_PHY -- enable PHY discovery +CONFIG_SYS_RX_ETH_BUFFER -- Set FEC Receive buffer +CONFIG_SYS_FAULT_ECHO_LINK_DOWN-- +CONFIG_SYS_FEC0_PINMUX -- Set FEC0 Pin configuration +CONFIG_SYS_FEC1_PINMUX -- Set FEC1 Pin configuration +CONFIG_SYS_FEC0_MIIBASE -- Set FEC0 MII base register +CONFIG_SYS_FEC1_MIIBASE -- Set FEC0 MII base register +MCFFEC_TOUT_LOOP -- set FEC timeout loop +CONFIG_HAS_ETH1 -- define to enable second FEC in u-boot + +CONFIG_ISO_PARTITION -- enable ISO read/write +CONFIG_DOS_PARTITION -- enable DOS read/write +CONFIG_IDE_RESET -- define ide_reset() +CONFIG_IDE_PREINIT -- define ide_preinit() +CONFIG_ATAPI -- define ATAPI support +CONFIG_LBA48 -- define LBA48 (larger than 120GB) support +CONFIG_SYS_IDE_MAXBUS -- define max channel +CONFIG_SYS_IDE_MAXDEVICE -- define max devices per channel +CONFIG_SYS_ATA_BASE_ADDR -- define ATA base address +CONFIG_SYS_ATA_IDE0_OFFSET -- define ATA IDE0 offset +CONFIG_SYS_ATA_DATA_OFFSET -- define ATA data IO +CONFIG_SYS_ATA_REG_OFFSET -- define for normal register accesses +CONFIG_SYS_ATA_ALT_OFFSET -- define for alternate registers +CONFIG_SYS_ATA_STRIDE -- define for Interval between registers +_IO_BASE -- define for IO base address + +CONFIG_MCFTMR -- define to use DMA timer +CONFIG_MCFPIT -- define to use PIT timer + +CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_HARD_I2C -- define for I2C hardware support +CONFIG_SOFT_I2C -- define for I2C bit-banged +CONFIG_SYS_I2C_SPEED -- define for I2C speed +CONFIG_SYS_I2C_SLAVE -- define for I2C slave address +CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset +CONFIG_SYS_IMMR -- define for MBAR offset + +CONFIG_PCI -- define for PCI support +CONFIG_PCI_PNP -- define for Plug n play support +CONFIG_SYS_PCI_MEM_BUS -- PCI memory logical offset +CONFIG_SYS_PCI_MEM_PHYS -- PCI memory physical offset +CONFIG_SYS_PCI_MEM_SIZE -- PCI memory size +CONFIG_SYS_PCI_IO_BUS -- PCI IO logical offset +CONFIG_SYS_PCI_IO_PHYS -- PCI IO physical offset +CONFIG_SYS_PCI_IO_SIZE -- PCI IO size +CONFIG_SYS_PCI_CFG_BUS -- PCI Configuration logical offset +CONFIG_SYS_PCI_CFG_PHYS -- PCI Configuration physical offset +CONFIG_SYS_PCI_CFG_SIZE -- PCI Configuration size + +CONFIG_EXTRA_CLOCK -- Enable extra clock such as vco, flexbus, pci, etc + +CONFIG_SYS_MBAR -- define MBAR offset + +CONFIG_SYS_ATMEL_BOOT -- To determine the u-boot is booted from Atmel or Intel + +CONFIG_MONITOR_IS_IN_RAM -- Not support + +CONFIG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF54455 internal SRAM + +CONFIG_SYS_CSn_BASE -- defines the Chip Select Base register +CONFIG_SYS_CSn_MASK -- defines the Chip Select Mask register +CONFIG_SYS_CSn_CTRL -- defines the Chip Select Control register + +CONFIG_SYS_ATMEL_BASE -- defines the Atmel Flash base +CONFIG_SYS_INTEL_BASE -- defines the Intel Flash base + +CONFIG_SYS_SDRAM_BASE -- defines the DRAM Base +CONFIG_SYS_SDRAM_BASE1 -- defines the DRAM Base 1 + +2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL +=========================================== +2.1. System memory map: + Flash: 0x00000000-0x3FFFFFFF (1024MB) + DDR: 0x40000000-0x7FFFFFFF (1024MB) + SRAM: 0x80000000-0x8FFFFFFF (256MB) + ATA: 0x90000000-0x9FFFFFFF (256MB) + PCI: 0xA0000000-0xBFFFFFFF (512MB) + FlexBus: 0xC0000000-0xDFFFFFFF (512MB) + IP: 0xF0000000-0xFFFFFFFF (256MB) + +2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and + linux kernel, you can customize it based on your system requirements: + Atmel boot: + Flash0: 0x00000000-0x0007FFFF (512KB) + Flash1: 0x04000000-0x05FFFFFF (32MB) + Intel boot: + Flash0: 0x00000000-0x01FFFFFF (32MB) + Flash1: 0x04000000-0x0407FFFF (512KB) + + CPLD: 0x08000000-0x08FFFFFF (16MB) + FPGA: 0x09000000-0x09FFFFFF (16MB) + DDR: 0x40000000-0x4FFFFFFF (256MB) + SRAM: 0x80000000-0x80007FFF (32KB) + IP: 0xFC000000-0xFC0FFFFF (64KB) + +3. SWITCH SETTINGS +================== +3.1 SW1 Pin3: 0 - Boot from Atmel or 1 - INTEL + SW1 Pin4: 0 - ULPI chip not in reset state or 1 - ULPI chip in reset state + SW1 Pin5: 0 - Full ATA Bus enabled, FEC Phy1 powered down + 1 - Upper 8 bits ATA data bus disabled, FEC PHY1 active + SW1 Pin6: 0 - FEC Phy0 active or 1 - FEC Phy0 powered down + SW1 Pin3: 0 - Boot from Atmel or 1 - INTEL + +4. COMPILATION +============== +4.1 To create U-Boot the gcc-4.1-32 compiler set (ColdFire ELF version) +from codesourcery.com was used. Download it from: +http://www.codesourcery.com/gnu_toolchains/coldfire/download.html + +4.2 Compilation + export CROSS_COMPILE=cross-compile-prefix + cd u-boot-1.x.x + make distclean + make M54455EVB_config, or - default to atmel 33Mhz input clock + make M54455EVB_atmel_config, or - default to atmel 33Mhz input clock + make M54455EVB_a33_config, or - default to atmel 33Mhz input clock + make M54455EVB_a66_config, or - default to atmel 66Mhz input clock + make M54455EVB_intel_config, or - default to intel 33Mhz input clock + make M54455EVB_i33_config, or - default to intel 33Mhz input clock + make M54455EVB_i66_config, or - default to intel 66Mhz input clock + make + +5. SCREEN DUMP +============== +5.1 M54455EVB Development board + Boot from Atmel (NOTE: May not show exactly the same) + +U-Boot 1.2.0-g98c80b46-dirty (Jul 26 2007 - 12:44:08) + +CPU: Freescale MCF54455 (Mask:48 Version:1) + CPU CLK 266 Mhz BUS CLK 133 Mhz FLB CLK 66 Mhz + PCI CLK 33 Mhz INP CLK 33 Mhz VCO CLK 533 Mhz +Board: Freescale M54455 EVB +I2C: ready +DRAM: 256 MB +FLASH: 16.5 MB +In: serial +Out: serial +Err: serial +Net: FEC0, FEC1 +IDE: Bus 0: not available +-> print +bootargs=root=/dev/ram rw +bootdelay=1 +baudrate=115200 +ethaddr=00:e0:0c:bc:e5:60 +eth1addr=00:e0:0c:bc:e5:61 +hostname=M54455EVB +netdev=eth0 +inpclk=33333333 +loadaddr=40010000 +load=tftp ${loadaddr) ${u-boot} +upd=run load; run prog +prog=prot off 0 2ffff;era 0 2ffff;cp.b ${loadaddr} 0 ${filesize};save +ethact=FEC0 +mtdids=nor0=M54455EVB-1 +mtdparts=M54455EVB-1:16m(user) +u-boot=u-boot54455.bin +filesize=292b4 +fileaddr=40010000 +gatewayip=192.168.1.1 +netmask=255.255.255.0 +ipaddr=192.168.1.3 +serverip=192.168.1.2 +stdin=serial +stdout=serial +stderr=serial +mem=261632k + +Environment size: 563/8188 bytes +-> bdinfo +memstart = 0x40000000 +memsize = 0x10000000 +flashstart = 0x00000000 +flashsize = 0x01080000 +flashoffset = 0x00000000 +sramstart = 0x80000000 +sramsize = 0x00008000 +mbar = 0xFC000000 +busfreq = 133.333 MHz +pcifreq = 33.333 MHz +flbfreq = 66.666 MHz +inpfreq = 33.333 MHz +vcofreq = 533.333 MHz +ethaddr = 00:E0:0C:BC:E5:60 +eth1addr = 00:E0:0C:BC:E5:61 +ip_addr = 192.168.1.3 +baudrate = 115200 bps +-> +-> help +? - alias for 'help' +base - print or set address offset +bdinfo - print Board Info structure +boot - boot default, i.e., run 'bootcmd' +bootd - boot default, i.e., run 'bootcmd' +bootelf - Boot from an ELF image in memory +bootm - boot application image from memory +bootp - boot image via network using BootP/TFTP protocol +bootvx - Boot vxWorks from an ELF image +cmp - memory compare +coninfo - print console devices and information +cp - memory copy +crc32 - checksum calculation +date - get/set/reset date & time +dcache - enable or disable data cache +diskboot- boot from IDE device +echo - echo args to console +erase - erase FLASH memory +ext2load- load binary file from a Ext2 filesystem +ext2ls - list files in a directory (default /) +fatinfo - print information about filesystem +fatload - load binary file from a dos filesystem +fatls - list files in a directory (default /) +flinfo - print FLASH memory information +fsinfo - print information about filesystems +fsload - load binary file from a filesystem image +go - start application at address 'addr' +help - print online help +i2c - I2C sub-system +icache - enable or disable instruction cache +ide - IDE sub-system +iminfo - print header information for application image +imls - list all images found in flash +itest - return true/false on integer compare +loadb - load binary file over serial line (kermit mode) +loads - load S-Record file over serial line +loady - load binary file over serial line (ymodem mode) +loop - infinite loop on address range +ls - list files in a directory (default /) +md - memory display +mii - MII utility commands +mm - memory modify (auto-incrementing) +mtest - simple RAM test +mw - memory write (fill) +nfs - boot image via network using NFS protocol +nm - memory modify (constant address) +pci - list and access PCI Configuration Space +ping - send ICMP ECHO_REQUEST to network host +printenv- print environment variables +protect - enable or disable FLASH write protection +rarpboot- boot image via network using RARP/TFTP protocol +reset - Perform RESET of the CPU +run - run commands in an environment variable +saveenv - save environment variables to persistent storage +setenv - set environment variables +sleep - delay execution for some time +source - run script from memory +tftpboot- boot image via network using TFTP protocol +version - print monitor version +->bootm 4000000 + +## Booting image at 04000000 ... + Image Name: Linux Kernel Image + Created: 2007-08-14 15:13:00 UTC + Image Type: M68K Linux Kernel Image (uncompressed) + Data Size: 2301952 Bytes = 2.2 MB + Load Address: 40020000 + Entry Point: 40020000 + Verifying Checksum ... OK +OK +Linux version 2.6.20-gfe5136d6-dirty (mattw@kea) (gcc version 4.2.0 20070318 (pr +erelease) (Sourcery G++ Lite 4.2-20)) #108 Mon Aug 13 13:00:13 MDT 2007 +starting up linux startmem 0xc0254000, endmem 0xcfffffff, size 253MB +Built 1 zonelists. Total pages: 32624 +Kernel command line: root=/dev/mtdblock1 rw rootfstype=jffs2 ip=none mtdparts=ph +ysmap-flash.0:5M(kernel)ro,-(jffs2) +PID hash table entries: 1024 (order: 10, 4096 bytes) +Console: colour dummy device 80x25 +Dentry cache hash table entries: 32768 (order: 4, 131072 bytes) +Inode-cache hash table entries: 16384 (order: 3, 65536 bytes) +Memory: 257496k/262136k available (1864k kernel code, 2440k data, 88k init) +Mount-cache hash table entries: 1024 +NET: Registered protocol family 16 +SCSI subsystem initialized +NET: Registered protocol family 2 +IP route cache hash table entries: 2048 (order: 0, 8192 bytes) +TCP established hash table entries: 8192 (order: 2, 32768 bytes) +TCP bind hash table entries: 4096 (order: 1, 16384 bytes) +TCP: Hash tables configured (established 8192 bind 4096) +TCP reno registered +JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. +io scheduler noop registered +io scheduler anticipatory registered +io scheduler deadline registered +io scheduler cfq registered (default) +ColdFire internal UART serial driver version 1.00 +ttyS0 at 0xfc060000 (irq = 90) is a builtin ColdFire UART +ttyS1 at 0xfc064000 (irq = 91) is a builtin ColdFire UART +ttyS2 at 0xfc068000 (irq = 92) is a builtin ColdFire UART +RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize +loop: loaded (max 8 devices) +FEC ENET Version 0.2 +fec: PHY @ 0x0, ID 0x20005ca2 -- DP83849 +eth0: ethernet 00:08:ee:00:e4:19 +physmap platform flash device: 01000000 at 04000000 +physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank + Intel/Sharp Extended Query Table at 0x0031 +Using buffer write method +cfi_cmdset_0001: Erase suspend on write enabled +2 cmdlinepart partitions found on MTD device physmap-flash.0 +Creating 2 MTD partitions on "physmap-flash.0": +0x00000000-0x00500000 : "kernel" +mtd: Giving out device 0 to kernel +0x00500000-0x01000000 : "jffs2" +mtd: Giving out device 1 to jffs2 +mice: PS/2 mouse device common for all mice +i2c /dev entries driver +TCP cubic registered +NET: Registered protocol family 1 +NET: Registered protocol family 17 +NET: Registered protocol family 15 +VFS: Mounted root (jffs2 filesystem). +Setting the hostname to freescale +Mounting filesystems +mount: Mounting usbfs on /proc/bus/usb failed: No such file or directory +Starting syslogd and klogd +Setting up networking on loopback device: +Setting up networking on eth0: +eth0: config: auto-negotiation on, 100FDX, 100HDX, 10FDX, 10HDX. +Adding static route for default gateway to 172.27.255.254: +Setting nameserver to 172.27.0.1 in /etc/resolv.conf: +Starting inetd: +/ # diff --git a/board/freescale/m547xevb/README b/board/freescale/m547xevb/README new file mode 100644 index 0000000000..d3aec20e4f --- /dev/null +++ b/board/freescale/m547xevb/README @@ -0,0 +1,272 @@ +Freescale MCF5475EVB ColdFire Development Board +================================================ + +TsiChung Liew(Tsi-Chung.Liew@freescale.com) +Created Jan 08, 2008 +=========================================== + + +Changed files: +============== + +- board/freescale/m547xevb/m547xevb.c Dram setup, IDE pre init, and PCI init +- board/freescale/m547xevb/mii.c MII init +- board/freescale/m547xevb/Makefile Makefile +- board/freescale/m547xevb/config.mk config make +- board/freescale/m547xevb/u-boot.lds Linker description + +- arch/m68k/cpu/mcf547x_8x/cpu.c cpu specific code +- arch/m68k/cpu/mcf547x_8x/cpu_init.c Flexbus ChipSelect, Mux pins setup, icache and RTC extra regs +- arch/m68k/cpu/mcf547x_8x/interrupts.c cpu specific interrupt support +- arch/m68k/cpu/mcf547x_8x/slicetimer.c Timer support +- arch/m68k/cpu/mcf547x_8x/speed.c system, pci, flexbus, and cpu clock +- arch/m68k/cpu/mcf547x_8x/Makefile Makefile +- arch/m68k/cpu/mcf547x_8x/config.mk config make +- arch/m68k/cpu/mcf547x_8x/start.S start up assembly code + +- doc/README.m5475evb This readme file + +- drivers/dma/MCD_dmaApi.c DMA API functions +- drivers/dma/MCD_tasks.c DMA Tasks +- drivers/dma/MCD_tasksInit.c DMA Tasks Init +- drivers/net/fsl_mcdmafec.c ColdFire common DMA FEC driver +- drivers/serial/mcfuart.c ColdFire common UART driver + +- include/MCD_dma.h DMA header file +- include/MCD_progCheck.h DMA header file +- include/MCD_tasksInit.h DMA header file +- include/asm-m68k/bitops.h Bit operation function export +- include/asm-m68k/byteorder.h Byte order functions +- include/asm-m68k/errno.h Error Number definition +- include/asm-m68k/fec.h FEC structure and definition +- include/asm-m68k/fsl_i2c.h I2C structure and definition +- include/asm-m68k/fsl_mcddmafec.h DMA FEC structure and definition +- include/asm-m68k/global_data.h Global data structure +- include/asm-m68k/immap.h ColdFire specific header file and driver macros +- include/asm-m68k/immap_547x_8x.h mcf547x_8x specific header file +- include/asm-m68k/io.h io functions +- include/asm-m68k/m547x_8x.h mcf547x_8x specific header file +- include/asm-m68k/posix_types.h Posix +- include/asm-m68k/processor.h header file +- include/asm-m68k/ptrace.h Exception structure +- include/asm-m68k/rtc.h Realtime clock header file +- include/asm-m68k/string.h String function export +- include/asm-m68k/timer.h Timer structure and definition +- include/asm-m68k/types.h Data types definition +- include/asm-m68k/uart.h Uart structure and definition +- include/asm-m68k/u-boot.h u-boot structure + +- include/configs/M5475EVB.h Board specific configuration file + +- arch/m68k/lib/board.c board init function +- arch/m68k/lib/cache.c +- arch/m68k/lib/interrupts Coldfire common interrupt functions +- arch/m68k/lib/m68k_linux.c +- arch/m68k/lib/traps.c Exception init code + +1 MCF547x specific Options/Settings +==================================== +1.1 pre-loader is no longer suppoer in thie coldfire family + +1.2 Configuration settings for M5475EVB Development Board +CONFIG_MCF547x_8x -- define for all MCF547x_8x CPUs +CONFIG_M547x -- define for all Freescale MCF547x CPUs +CONFIG_M5475 -- define for M5475EVB board + +CONFIG_MCFUART -- define to use common CF Uart driver +CONFIG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2 +CONFIG_BAUDRATE -- define UART baudrate + +CONFIG_FSLDMAFEC -- define to use common dma FEC driver +CONFIG_MII -- enable to use MII driver +CONFIG_CF_DOMII -- enable to use MII feature in cmd_mii.c +CONFIG_SYS_DISCOVER_PHY -- enable PHY discovery +CONFIG_SYS_RX_ETH_BUFFER -- Set FEC Receive buffer +CONFIG_SYS_FAULT_ECHO_LINK_DOWN-- +CONFIG_SYS_FEC0_PINMUX -- Set FEC0 Pin configuration +CONFIG_SYS_FEC1_PINMUX -- Set FEC1 Pin configuration +CONFIG_SYS_FEC0_MIIBASE -- Set FEC0 MII base register +CONFIG_SYS_FEC1_MIIBASE -- Set FEC0 MII base register +MCFFEC_TOUT_LOOP -- set FEC timeout loop +CONFIG_HAS_ETH1 -- define to enable second FEC in u-boot + +CONFIG_CMD_USB -- enable USB commands +CONFIG_USB_OHCI_NEW -- enable USB OHCI driver +CONFIG_USB_STORAGE -- enable USB Storage device +CONFIG_DOS_PARTITION -- enable DOS read/write + +CONFIG_SLTTMR -- define to use SLT timer + +CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_HARD_I2C -- define for I2C hardware support +CONFIG_SOFT_I2C -- define for I2C bit-banged +CONFIG_SYS_I2C_SPEED -- define for I2C speed +CONFIG_SYS_I2C_SLAVE -- define for I2C slave address +CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset +CONFIG_SYS_IMMR -- define for MBAR offset + +CONFIG_PCI -- define for PCI support +CONFIG_PCI_PNP -- define for Plug n play support +CONFIG_SKIPPCI_HOSTBRIDGE -- SKIP PCI Host bridge +CONFIG_SYS_PCI_MEM_BUS -- PCI memory logical offset +CONFIG_SYS_PCI_MEM_PHYS -- PCI memory physical offset +CONFIG_SYS_PCI_MEM_SIZE -- PCI memory size +CONFIG_SYS_PCI_IO_BUS -- PCI IO logical offset +CONFIG_SYS_PCI_IO_PHYS -- PCI IO physical offset +CONFIG_SYS_PCI_IO_SIZE -- PCI IO size +CONFIG_SYS_PCI_CFG_BUS -- PCI Configuration logical offset +CONFIG_SYS_PCI_CFG_PHYS -- PCI Configuration physical offset +CONFIG_SYS_PCI_CFG_SIZE -- PCI Configuration size + +CONFIG_SYS_MBAR -- define MBAR offset + +CONFIG_MONITOR_IS_IN_RAM -- Not support + +CONFIG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF547x internal SRAM + +CONFIG_SYS_CSn_BASE -- defines the Chip Select Base register +CONFIG_SYS_CSn_MASK -- defines the Chip Select Mask register +CONFIG_SYS_CSn_CTRL -- defines the Chip Select Control register + +CONFIG_SYS_SDRAM_BASE -- defines the DRAM Base + +2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL +=========================================== +2.1. System memory map: + Flash: 0xFF800000-0xFFFFFFFF (8MB) + DDR: 0x00000000-0x3FFFFFFF (1024MB) + SRAM: 0xF2000000-0xF2000FFF (4KB) + PCI: 0x70000000-0x8FFFFFFF (512MB) + IP: 0xF0000000-0xFFFFFFFF (256MB) + +3. COMPILATION +============== +3.1 To create U-Boot the gcc-4.x compiler set (ColdFire ELF or uclinux + version) from codesourcery.com was used. Download it from: + http://www.codesourcery.com/gnu_toolchains/coldfire/download.html + +3.2 Compilation + export CROSS_COMPILE=cross-compile-prefix + cd u-boot-1.x.x + make distclean + make M5475AFE_config, or - boot 2MB, RAM 64MB + make M5475BFE_config, or - boot 2MB, code 16MB, RAM 64MB + make M5475CFE_config, or - boot 2MB, code 16MB, Video, USB, RAM 64MB + make M5475DFE_config, or - boot 2MB, USB, RAM 64MB + make M5475EFE_config, or - boot 2MB, Video, USB, RAM 64MB + make M5475FFE_config, or - boot 2MB, code 32MB, Video, USB, RAM 128MB + make M5475GFE_config, or - boot 2MB, RAM 64MB + make + +5. SCREEN DUMP +============== +5.1 + +U-Boot 1.3.1 (Jan 8 2008 - 12:47:44) + +CPU: Freescale MCF5475 + CPU CLK 266 Mhz BUS CLK 133 Mhz +Board: Freescale FireEngine 5475 EVB +I2C: ready +DRAM: 64 MB +FLASH: 18 MB +In: serial +Out: serial +Err: serial +Net: FEC0, FEC1 +-> pri +bootdelay=1 +baudrate=115200 +ethaddr=00:e0:0c:bc:e5:60 +eth1addr=00:e0:0c:bc:e5:61 +ipaddr=192.162.1.2 +serverip=192.162.1.1 +gatewayip=192.162.1.1 +netmask=255.255.255.0 +hostname=M547xEVB +netdev=eth0 +loadaddr=10000 +u-boot=u-boot.bin +load=tftp ${loadaddr) ${u-boot} +upd=run load; run prog +prog=prot off bank 1;era ff800000 ff82ffff;cp.b ${loadaddr} ff800000 ${filesize};save +stdin=serial +stdout=serial +stderr=serial +ethact=FEC0 +mem=65024k + +Environment size: 433/8188 bytes +-> bdin +memstart = 0x00000000 +memsize = 0x04000000 +flashstart = 0xFF800000 +flashsize = 0x01200000 +flashoffset = 0x00000000 +sramstart = 0xF2000000 +sramsize = 0x00001000 +mbar = 0xF0000000 +busfreq = 133.333 MHz +pcifreq = 0 MHz +ethaddr = 00:E0:0C:BC:E5:60 +eth1addr = 00:E0:0C:BC:E5:61 +ip_addr = 192.162.1.2 +baudrate = 115200 bps +-> ? +? - alias for 'help' +base - print or set address offset +bdinfo - print Board Info structure +boot - boot default, i.e., run 'bootcmd' +bootd - boot default, i.e., run 'bootcmd' +bootelf - Boot from an ELF image in memory +bootm - boot application image from memory +bootp - boot image via network using BootP/TFTP protocol +bootvx - Boot vxWorks from an ELF image +cmp - memory compare +coninfo - print console devices and information +cp - memory copy +crc32 - checksum calculation +dcache - enable or disable data cache +echo - echo args to console +erase - erase FLASH memory +flinfo - print FLASH memory information +go - start application at address 'addr' +help - print online help +i2c - I2C sub-system +icache - enable or disable instruction cache +iminfo - print header information for application image +imls - list all images found in flash +itest - return true/false on integer compare +loadb - load binary file over serial line (kermit mode) +loads - load S-Record file over serial line +loady - load binary file over serial line (ymodem mode) +loop - infinite loop on address range +md - memory display +mii - MII utility commands +mm - memory modify (auto-incrementing) +mtest - simple RAM test +mw - memory write (fill) +nfs - boot image via network using NFS protocol +nm - memory modify (constant address) +pci - list and access PCI Configuration Space +ping - send ICMP ECHO_REQUEST to network host +printenv- print environment variables +protect - enable or disable FLASH write protection +rarpboot- boot image via network using RARP/TFTP protocol +reset - Perform RESET of the CPU +run - run commands in an environment variable +saveenv - save environment variables to persistent storage +setenv - set environment variables +sleep - delay execution for some time +source - run script from memory +tftpboot- boot image via network using TFTP protocol +usb - USB sub-system +usbboot - boot from USB device +version - print monitor version +-> usb start +(Re)start USB... +USB: OHCI pci controller (1131, 1561) found @(0:17:0) +OHCI regs address 0x80000000 +scanning bus for devices... 2 USB Device(s) found + scanning bus for storage devices... 1 Storage Device(s) found +-> diff --git a/board/freescale/mpc7448hpc2/README b/board/freescale/mpc7448hpc2/README new file mode 100644 index 0000000000..cbb043e1d0 --- /dev/null +++ b/board/freescale/mpc7448hpc2/README @@ -0,0 +1,184 @@ +Freescale MPC7448hpc2 (Taiga) board +=================================== + +Created 08/11/2006 Roy Zang +-------------------------- +MPC7448hpc2 (Taiga) board is a high-performance PowerPC server reference +design, which is optimized for high speed throughput between the processor and +the memory, disk drive and Ethernet port subsystems. + +MPC7448hpc2(Taiga) is designed to the micro-ATX chassis, allowing it to be +used in 1U or 2U rack-mount chassis¡¯, as well as in standard ATX/Micro-ATX +chassis. + +Building U-Boot +------------------ +The mpc7448hpc2 code base is known to compile using: + Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3 + + $ make mpc7448hpc2_config + Configuring for mpc7448hpc2 board... + + $ make + +Memory Map +---------- + +The memory map is setup for Linux to operate properly. + +The mapping is: + + Range Start Range End Definition Size + + 0x0000_0000 0x7fff_ffff DDR 2G + 0xe000_0000 0xe7ff_ffff PCI Memory 128M + 0xfa00_0000 0xfaff_ffff PCI IO 16M + 0xfb00_0000 0xfbff_ffff PCI Config 16M + 0xfc00_0000 0xfc0f_ffff NVRAM/CADMUS 1M + 0xfe00_0000 0xfeff_ffff PromJet 16M + 0xff00_0000 0xff80_0000 FLASH (boot flash) 8M + 0xff80_0000 0xffff_ffff FLASH (second half flash) 8M + +Using Flash +----------- + +The MPC7448hpc2 board has two "banks" of flash, each 8MB in size +(2^23 = 0x00800000). + +Note: the "bank" here refers to half of the flash. In fact, there is only one +bank of flash, which is divided into low and high half. Each is controlled by +the most significant bit of the address bus. The so called "bank" is only for +convenience. + +There is a switch which allows the "bank" to be selected. The switch +settings for updating flash are given below. + +The u-boot commands for copying the boot-bank into the secondary bank are +as follows: + + erase ff800000 ff880000 + cp.b ff000000 ff800000 80000 + +U-boot commands for downloading an image via tftp and flashing +it into the secondary bank: + + tftp 10000 + erase ff000000 ff080000 + cp.b 10000 ff000000 80000 + +After copying the image into the second bank of flash, be sure to toggle +SW3[4] on board before resetting the board in order to set the +secondary bank as the boot-bank. + +Board Switches +---------------------- + +Most switches on the board should not be changed. The most frequent +user-settable switches on the board are used to configure +the flash banks and determining the PCI frequency. + +SW1[1-5]: Processor core voltage + + 12345 Core Voltage + ----- + SW1=01111 1.000V. + SW1=01101 1.100V. + SW1=01011 1.200V. + SW1=01001 1.300V only for MPC7447A. + + +SW2[1-6]: CPU core frequency + + CPU Core Frequency (MHz) + Bus Frequency + 123456 100 133 167 200 Ratio + + ------ + SW2=101100 500 667 833 1000 5x + SW2=100100 550 733 917 1100 5.5x + SW2=110100 600 800 1000 1200 6x + SW2=010100 650 866 1083 1300 6.5x + SW2=001000 700 930 1167 1400 7x + SW2=000100 750 1000 1250 1500 7.5x + SW2=110000 800 1066 1333 1600 8x + SW2=011000 850 1333 1417 1700 8.5x only for MPC7447A + SW2=011110 900 1200 1500 1800 9x + +This table shows only a subset of available frequency options; see the CPU +hardware specifications for more information. + +SW2[7-8]: Bus Protocol and CPU Reset Option + + 7 + - + SW2=0 System bus uses MPX bus protocol + SW2=1 System bus uses 60x bus protocol + + 8 + - + SW2=0 TSI108 can cause CPU reset + SW2=1 TSI108 can not cause CPU reset + +SW3[1-8] system options + + 123 + --- + SW3=xxx Connected to GPIO[0:2] on TSI108 + + 4 + - + SW3=0 CPU boots from low half of flash + SW3=1 CPU boots from high half of flash + + 5 + - + SW3=0 SATA and slot2 connected to PCI bus + SW3=1 Only slot1 connected to PCI bus + + 6 + - + SW3=0 USB connected to PCI bus + SW3=1 USB disconnected from PCI bus + + 7 + - + SW3=0 Flash is write protected + SW3=1 Flash is NOT write protected + + 8 + - + SW3=0 CPU will boot from flash + SW3=1 CPU will boot from PromJet + +SW4[1-3]: System bus frequency + + Bus Frequency (MHz) + --- + SW4=010 183 + SW4=011 100 + SW4=100 133 + SW4=101 166 only for MPC7447A + SW4=110 200 only for MPC7448 + others reserved + +SW4[4-6]: DDR2 SDRAM frequency + + Bus Frequency (MHz) + --- + SW4=000 external clock + SW4=011 system clock + SW4=100 133 + SW4=101 166 + SW4=110 200 + others reserved + +SW4[7-8]: PCI/PCI-X frequency control + 7 + - + SW4=0 PCI/PCI-X bus operates normally + SW4=1 PCI bus forced to PCI-33 mode + + 8 + - + SW4=0 PCI-X mode at 133 MHz allowed + SW4=1 PCI-X mode limited to 100 MHz diff --git a/board/freescale/mpc8313erdb/README b/board/freescale/mpc8313erdb/README new file mode 100644 index 0000000000..be7ef32b45 --- /dev/null +++ b/board/freescale/mpc8313erdb/README @@ -0,0 +1,111 @@ +Freescale MPC8313ERDB Board +----------------------------------------- + +1. Board Switches and Jumpers + + S3 is used to set CONFIG_SYS_RESET_SOURCE. + + To boot the image at 0xFE000000 in NOR flash, use these DIP + switch settings for S3 S4: + + +------+ +------+ + | | | **** | + | **** | | | + +------+ ON +------+ ON + 4321 4321 + (where the '*' indicates the position of the tab of the switch.) + + To boot the image at the beginning of NAND flash, use these + DIP switch settings for S3 S4: + + +------+ +------+ + | * | | *** | + | *** | | * | + +------+ ON +------+ ON + 4321 4321 + (where the '*' indicates the position of the tab of the switch.) + + When booting from NAND, use u-boot-nand.bin, not u-boot.bin. + +2. Memory Map + The memory map looks like this: + + 0x0000_0000 0x07ff_ffff DDR 128M + 0x8000_0000 0x8fff_ffff PCI MEM 256M + 0x9000_0000 0x9fff_ffff PCI_MMIO 256M + 0xe000_0000 0xe00f_ffff IMMR 1M + 0xe200_0000 0xe20f_ffff PCI IO 16M + 0xe280_0000 0xe280_7fff NAND FLASH (CS1) 32K + 0xf000_0000 0xf001_ffff VSC7385 (CS2) 128K + 0xfa00_0000 0xfa00_7fff Board Status/ 32K + LED Control (CS3) + 0xfe00_0000 0xfe7f_ffff NOR FLASH (CS0) 8M + + When booting from NAND, NAND flash is CS0 and NOR flash + is CS1. + +3. Definitions + +3.1 Explanation of NEW definitions in: + + include/configs/MPC8313ERDB.h + + CONFIG_MPC83xx MPC83xx family + CONFIG_MPC831x MPC831x specific + CONFIG_MPC8313ERDB MPC8313ERDB board specific + +4. Compilation + + Assuming you're using BASH (or similar) as your shell: + + export CROSS_COMPILE=your-cross-compiler-prefix- + make distclean + make MPC8313ERDB_XXX_config + (where XXX is: + 33 - 33 MHz oscillator, boot from NOR flash + 66 - 66 MHz oscillator, boot from NOR flash + NAND_33 - 33 MHz oscillator, boot from NAND flash + NAND_66 - 66 MHz oscillator, boot from NAND flash) + make + +5. Downloading and Flashing Images + +5.1 Reflash U-boot Image using U-boot + + NOR flash: + + =>run tftpflash + + You may want to try + =>tftpboot $loadaddr $uboot + first, to make sure that the TFTP load will succeed before it + goes ahead and wipes out your current firmware. And of course, + have an alternate means of programming the flash available + if the new u-boot doesn't boot. + + NAND flash: + + =>tftpboot $loadaddr + =>nand erase 0 0x80000 + =>nand write $loadaddr 0 0x80000 + + ...where 0x80000 is the filesize rounded up to + the next 0x20000 increment. + +5.2 Downloading and Booting Linux Kernel + + Ensure that all networking-related environment variables are set + properly (including ipaddr, serverip, gatewayip (if needed), + netmask, ethaddr, eth1addr, rootpath (if using NFS root), + fdtfile, and bootfile). + + Then, do one of the following, depending on whether you + want an NFS root or a ramdisk root: + + =>run nfsboot + or + =>run ramboot + +6 Notes + + The console baudrate for MPC8313ERDB is 115200bps. diff --git a/board/freescale/mpc8315erdb/README b/board/freescale/mpc8315erdb/README new file mode 100644 index 0000000000..b32132d053 --- /dev/null +++ b/board/freescale/mpc8315erdb/README @@ -0,0 +1,105 @@ +Freescale MPC8315ERDB Board +----------------------------------------- + +1. Board Switches and Jumpers + + S3 is used to set CONFIG_SYS_RESET_SOURCE. + + To boot the image at 0xFE000000 in NOR flash, use these DIP + switch settings for S3 S4: + + +------+ +------+ + | | | **** | + | **** | | | + +------+ ON +------+ ON + 4321 4321 + (where the '*' indicates the position of the tab of the switch.) + + To boot the image at the beginning of NAND flash, use these + DIP switch settings for S3 S4: + + +------+ +------+ + | * | | *** | + | *** | | * | + +------+ ON +------+ ON + 4321 4321 + (where the '*' indicates the position of the tab of the switch.) + + When booting from NAND, use u-boot-nand.bin, not u-boot.bin. + +2. Memory Map + The memory map looks like this: + + 0x0000_0000 0x07ff_ffff DDR 128M + 0x8000_0000 0x8fff_ffff PCI MEM 256M + 0x9000_0000 0x9fff_ffff PCI_MMIO 256M + 0xe000_0000 0xe00f_ffff IMMR 1M + 0xe030_0000 0xe03f_ffff PCI IO 1M + 0xe060_0000 0xe060_7fff NAND FLASH (CS1) 32K + 0xfe00_0000 0xfe7f_ffff NOR FLASH (CS0) 8M + + When booting from NAND, NAND flash is CS0 and NOR flash + is CS1. + +3. Definitions + +3.1 Explanation of NEW definitions in: + + include/configs/MPC8315ERDB.h + + CONFIG_MPC83xx MPC83xx family + CONFIG_MPC831x MPC831x specific + CONFIG_MPC8315 MPC8315 specific + CONFIG_MPC8315ERDB MPC8315ERDB board specific + +4. Compilation + + Assuming you're using BASH (or similar) as your shell: + + export CROSS_COMPILE=your-cross-compiler-prefix- + make distclean + make MPC8315ERDB_config (or MPC8315ERDB_NAND_config for u-boot-nand.bin) + make all + +5. Downloading and Flashing Images + +5.1 Reflash U-boot Image using U-boot + + NOR flash: + + tftp 40000 u-boot.bin + protect off all + erase fe000000 fe1fffff + + cp.b 40000 fe000000 xxxx + protect on all + + You have to supply the correct byte count with 'xxxx' + from the TFTP result log. + + NAND flash: + + =>tftpboot $loadaddr + =>nand erase 0 0x80000 + =>nand write $loadaddr 0 0x80000 + + ...where 0x80000 is the filesize rounded up to + the next 0x20000 increment. + +5.2 Downloading and Booting Linux Kernel + + Ensure that all networking-related environment variables are set + properly (including ipaddr, serverip, gatewayip (if needed), + netmask, ethaddr, eth1addr, rootpath (if using NFS root), + fdtfile, and bootfile). + + Then, do one of the following, depending on whether you + want an NFS root or a ramdisk root: + + =>run nfsboot + or + =>run ramboot + +6 Notes + + The console baudrate for MPC8315ERDB is 115200bps. diff --git a/board/freescale/mpc8323erdb/README b/board/freescale/mpc8323erdb/README new file mode 100644 index 0000000000..6f89829373 --- /dev/null +++ b/board/freescale/mpc8323erdb/README @@ -0,0 +1,71 @@ +Freescale MPC8323ERDB Board +----------------------------------------- + +1. Memory Map + The memory map looks like this: + + 0x0000_0000 0x03ff_ffff DDR 64M + 0x8000_0000 0x8fff_ffff PCI MEM 256M + 0x9000_0000 0x9fff_ffff PCI_MMIO 256M + 0xe000_0000 0xe00f_ffff IMMR 1M + 0xd000_0000 0xd3ff_ffff PCI IO 64M + 0xfe00_0000 0xfeff_ffff NOR FLASH (CS0) 16M + +2. Compilation + + Assuming you're using BASH (or similar) as your shell: + + export CROSS_COMPILE=your-cross-compiler-prefix- + make distclean + make MPC8323ERDB_config + make + +3. Downloading and Flashing Images + +3.1 Reflash U-boot Image using U-boot + + N.b, have an alternate means of programming + the flash available if the new u-boot doesn't boot. + + First try a: + + tftpboot $loadaddr $uboot + + to make sure that the TFTP load will succeed before + an erase goes ahead and wipes out your current firmware. + Then do a: + + run tftpflash + + which is a shorter version of the manual sequence: + + tftp $loadaddr u-boot.bin + protect off fe000000 +$filesize + erase fe000000 +$filesize + cp.b $loadaddr fe000000 $filesize + + To keep your old u-boot's environment variables, do a: + + saveenv + + prior to resetting the board. + +3.2 Downloading and Booting Linux Kernel + + Ensure that all networking-related environment variables are set + properly (including ipaddr, serverip, gatewayip (if needed), + netmask, ethaddr, eth1addr, rootpath (if using NFS root), + fdtfile, and bootfile). + + Then, do one of the following, depending on whether you + want an NFS root or a ramdisk root: + + run nfsboot + + or + + run ramboot + +4 Notes + + The console baudrate for MPC8323ERDB is 115200bps. diff --git a/board/freescale/mpc832xemds/README b/board/freescale/mpc832xemds/README new file mode 100644 index 0000000000..4142aa9c8d --- /dev/null +++ b/board/freescale/mpc832xemds/README @@ -0,0 +1,128 @@ +Freescale MPC832XEMDS Board +----------------------------------------- +1. Board Switches and Jumpers +1.0 There are five Dual-In-Line Packages(DIP) Switches on MPC832XE SYS board + For some reason, the HW designers describe the switch settings + in terms of 0 and 1, and then map that to physical switches where + the label "On" refers to logic 0 and "Off" is logic 1. + + Switch bits are numbered 1 through, like, 4 6 8 or 10, but the + bits may contribute to signals that are numbered based at 0, + and some of those signals may be high-bit-number-0 too. Heed + well the names and labels and do not get confused. + + "Off" == 1 + "On" == 0 + + SW3 is switch 18 as silk-screened onto the board. + SW4[8] is the bit labeled 8 on Switch 4. + SW5[1:6] refers to bits labeled 1 through 6 in order on switch 5. + SW6[7:1] refers to bits labeled 7 through 1 in order on switch 6. + SW7[1:8]= 0000_0001 refers to bits labeled 1 through 6 is set as "On" + and bits labeled 8 is set as "Off". + +1.1 For the MPC832XEMDS PROTO Board + + First, make sure the board default setting is consistent with the document + shipped with your board. Then apply the following setting: + SW3[1-8]= 0000_1000 (core PLL setting, core enable) + SW4[1-8]= 0001_0010 (Flash boot on local bus, system PLL setting) + SW5[1-8]= 0010_0110 (Boot from high end) + SW6[1-8]= 0011_0100 (Flash boot on 16 bit local bus) + SW7[1-8]= 1000_0011 (QE PLL setting) + + ENET3/4 MII mode settings: + J1 1-2 (ETH3_TXER) + J2 2-3 (MII mode) + J3 2-3 (MII mode) + J4 2-3 (ADSL clockOscillator) + J5 1-2 (ETH4_TXER) + J6 2-3 (ClockOscillator) + JP1 removed (don't force PORESET) + JP2 mounted (ETH4/2 MII) + JP3 mounted (ETH3 MII) + JP4 mounted (HRCW from BCSR) + + ENET3/4 RMII mode settings: + J1 1-2 (ETH3_TXER) + J2 1-2 (RMII mode) + J3 1-2 (RMII mode) + J4 2-3 (ADSL clockOscillator) + J5 1-2 (ETH4_TXER) + J6 2-3 (ClockOscillator) + JP1 removed (don't force PORESET) + JP2 removed (ETH4/2 RMII) + JP3 removed (ETH3 RMII) + JP4 removed (HRCW from FLASH) + + on board Oscillator: 66M + + +2. Memory Map + +2.1 The memory map should look pretty much like this: + + 0x0000_0000 0x7fff_ffff DDR 2G + 0x8000_0000 0x8fff_ffff PCI MEM prefetch 256M + 0x9000_0000 0x9fff_ffff PCI MEM non-prefetch 256M + 0xc000_0000 0xdfff_ffff Empty 512M + 0xe000_0000 0xe01f_ffff Int Mem Reg Space 2M + 0xe020_0000 0xe02f_ffff Empty 1M + 0xe030_0000 0xe03f_ffff PCI IO 1M + 0xe040_0000 0xefff_ffff Empty 252M + 0xf400_0000 0xf7ff_ffff Empty 64M + 0xf800_0000 0xf800_7fff BCSR on CS1 32K + 0xf800_8000 0xf800_ffff PIB CS2 32K + 0xf801_0000 0xf801_7fff PIB CS3 32K + 0xfe00_0000 0xfeff_ffff FLASH on CS0 16M + + +3. Definitions + +3.1 Explanation of NEW definitions in: + + include/configs/MPC832XEPB.h + + CONFIG_MPC83xx MPC83xx family for MPC8349, MPC8360 and MPC832x + CONFIG_MPC832x MPC832x specific + CONFIG_MPC832XEMDS MPC832XEMDS board specific + +4. Compilation + + Assuming you're using BASH shell: + + export CROSS_COMPILE=your-cross-compile-prefix + cd u-boot + make distclean + make MPC832XEMDS_config + make + + MPC832x support PCI 33MHz and PCI 66MHz, to make u-boot support PCI: + + 1)Make sure the DIP SW support PCI mode as described in Section 1.1. + + 2)To Make U-Boot image support PCI 33MHz, use + Make MPC832XEMDS_HOST_33_config + + 3)To Make U-Boot image support PCI 66MHz, use + Make MPC832XEMDS_HOST_66M_config + +5. Downloading and Flashing Images + +5.0 Download over network: + + tftp 10000 u-boot.bin + +5.1 Reflash U-boot Image using U-boot + + tftp 20000 u-boot.bin + protect off fe000000 fe0fffff + erase fe000000 fe0fffff + cp.b 20000 fe000000 xxxx + +You have to supply the correct byte count with 'xxxx' from the TFTP result log. +Maybe 3ffff will work too, that corresponds to the erased sectors. + + +6. Notes + 1) The console baudrate for MPC832XEMDS is 115200bps. diff --git a/board/freescale/mpc8349itx/README b/board/freescale/mpc8349itx/README new file mode 100644 index 0000000000..48bbd50356 --- /dev/null +++ b/board/freescale/mpc8349itx/README @@ -0,0 +1,187 @@ +Freescale MPC8349E-mITX and MPC8349E-mITX-GP Boards +--------------------------------------------------- + +1. Board Description + + The MPC8349E-mITX and MPC8349E-mITX-GP are reference boards featuring + the Freescale MPC8349E processor in a Mini-ITX form factor. + + The MPC8349E-mITX-GP is an MPC8349E-mITX with the following differences: + + A) One 8MB on-board flash EEPROM chip, instead of two. + B) No SATA controller + C) No Compact Flash slot + D) No Mini-PCI slot + E) No Vitesse 7385 5-port Ethernet switch + F) No 4-port USB Type-A interface + +2. Board Switches and Jumpers + +2.0 Descriptions for all of the board jumpers can be found in the User + Guide. Of particular interest to U-Boot developers is jumper J22: + + Pos. Name Default Description + ----------------------------------------------------------------------- + A LGPL0 ON (0) HRCW source, bit 0 + B LGPL1 ON (0) HRCW source, bit 1 + C LGPL3 ON (0) HRCW source, bit 2 + D LGPL5 OFF (1) PCI_SYNC_OUT frequency + E BOOT1 ON (0) Flash EEPROM boot device + F PCI_M66EN ON (0) PCI 66MHz enable + G I2C-WP ON (0) I2C EEPROM write protection + H F_WP OFF (1) Flash EEPROM write protection + + Jumper J22.E is only for the ITX, and it decides the configuration + of the flash chips. If J22.E is ON (i.e. jumpered), then flash chip + U4 is located at address FE000000 and flash chip U7 is at FE800000. + If J22.E is OFF, then U7 is at FE000000 and U4 is at FE800000. + + For U-Boot development, J22.E can be used to switch back-and-forth + between two U-Boot images. + +3. Memory Map + +3.1. The memory map should look pretty much like this: + + 0x0000_0000 - 0x0FFF_FFFF DDR SDRAM (256 MB) + 0x8000_0000 - 0x9FFF_FFFF PCI1 memory space (512 MB) + 0xA000_0000 - 0xBFFF_FFFF PCI2 memory space (512 MB) + 0xE000_0000 - 0xEFFF_FFFF IMMR (1 MB) + 0xE200_0000 - 0xE2FF_FFFF PCI1 I/O space (16 MB) + 0xE300_0000 - 0xE3FF_FFFF PCI2 I/O space (16 MB) + 0xF000_0000 - 0xF000_FFFF Compact Flash (ITX only) + 0xF001_0000 - 0xF001_FFFF Local bus expansion slot + 0xF800_0000 - 0xF801_FFFF Vitesse 7385 Parallel Interface (ITX only) + 0xFE00_0000 - 0xFE7F_FFFF First 8MB bank of Flash memory + 0xFE80_0000 - 0xFEFF_FFFF Second 8MB bank of Flash memory (ITX only) + +3.2 Flash EEPROM layout. + + On the ITX, jumper J22.E is used to determine which flash chips are + at which address. When J22.E is switched, addresses from FE000000 + to FE7FFFFF are swapped with addresses from FE800000 to FEFFFFFF. + + On the ITX, at the normal boot address (aka HIGHBOOT): + + FE00_0000 HRCW + FE70_0000 Alternative U-Boot image + FE80_0000 Alternative HRCW + FEF0_0000 U-Boot image + FEFF_FFFF End of flash + + On the ITX, at the low boot address (LOWBOOT) + + FE00_0000 HRCW and U-Boot image + FE04_0000 U-Boot environment variables + FE80_0000 Alternative HRCW and U-Boot image + FEFF_FFFF End of flash + + On the ITX-GP, the only option is LOWBOOT and there is only one chip + + FE00_0000 HRCW and U-Boot image + FE04_0000 U-Boot environment variables + F7FF_FFFF End of flash + +4. Definitions + +4.1 Explanation of NEW definitions in: + + include/configs/MPC8349ITX.h + + CONFIG_MPC83xx MPC83xx family + CONFIG_MPC8349 MPC8349 specific + CONFIG_MPC8349ITX MPC8349E-mITX + CONFIG_MPC8349ITXGP MPC8349E-mITX-GP + +5. Compilation + + Assuming you're using BASH shell: + + export CROSS_COMPILE=your-cross-compile-prefix + cd u-boot + make distclean + + make MPC8349ITX_config + or: + make MPC8349ITXGP_config + or: + make MPC8349ITX_LOWBOOT_config + + make + +6. Downloading and Flashing Images + +6.1 Download via tftp: + + tftp $loadaddr + + where "" is the path and filename, on the TFTP server, of + the U-Boot image. + +6.1 Reflash U-Boot Image using U-Boot + + setenv uboot + run tftpflash + + where "" is the path and filename, on the TFTP server, of + the U-Boot image. + +6.2 Using the HRCW to switch between two different U-Boot images on the ITX + + Because the ITX has 16MB of flash, it is possible to keep two U-Boot + images in flash, and use the HRCW to specify which one is to be used + when the board boots. This trick is especially effective with a + hardware debugger that can override the HRCW, such as the BDI-2000. + + When the BMS bit in the HRCW is 0, the ITX will boot the U-Boot image + at address FE000000. When the BMS bit is 1, the ITX will boot the + image at address FEF00000. + + Therefore, just put a U-Boot image at both FE000000 and FEF00000 and + change the BMS bit whenever you want to boot the other image. + + Step-by-step instructions: + + 1) Build an ITX image to be loaded at FEF00000 + + make distclean + make MPC8349ITX_config + make + + 2) Take the u-boot.bin image and flash it at FEF00000. + + tftp $loadaddr u-boot.bin + protect off all + erase FEF00000 +$filesize + cp.b $loadaddr FEF00000 $filesize + + 3) Build an ITX image to be loaded at FE000000 + + make distclean + make MPC8349ITX_LOWBOOT_config + make + + 4) Take the u-boot.bin image and flash it at FE000000. + + tftp $loadaddr u-boot.bin + protect off FE000000 +$filesize + erase FE000000 +$filesize + cp.b $loadaddr FE000000 $filesize + + The HRCW in flash is currently set to boot the image at FE000000. + + If you have a hardware debugger, configure it to set the HRCW to + B460A000 04040000 if you want to boot the image at FEF00000, or set + it to B060A000 04040000 if you want to boot the image at FE000000. + + To change the HRCW in flash to boot the image at FEF00000, use these + U-Boot commands: + + cp.b FE000000 1000 10000 ; copy 1st flash sector to 1000 + mw.b 1020 b4 8 ; modify BMS bit + protect off FE000000 +10000 + erase FE000000 +10000 + cp.b 1000 FE000000 10000 + +7. Notes + 1) The console baudrate for MPC8349EITX is 115200bps. diff --git a/board/freescale/mpc8360emds/README b/board/freescale/mpc8360emds/README new file mode 100644 index 0000000000..6afa753969 --- /dev/null +++ b/board/freescale/mpc8360emds/README @@ -0,0 +1,155 @@ +Freescale MPC8360EMDS Board +----------------------------------------- +1. Board Switches and Jumpers +1.0 There are four Dual-In-Line Packages(DIP) Switches on MPC8360EMDS board + For some reason, the HW designers describe the switch settings + in terms of 0 and 1, and then map that to physical switches where + the label "On" refers to logic 0 and "Off" is logic 1. + + Switch bits are numbered 1 through, like, 4 6 8 or 10, but the + bits may contribute to signals that are numbered based at 0, + and some of those signals may be high-bit-number-0 too. Heed + well the names and labels and do not get confused. + + "Off" == 1 + "On" == 0 + + SW18 is switch 18 as silk-screened onto the board. + SW4[8] is the bit labeled 8 on Switch 4. + SW2[1:6] refers to bits labeled 1 through 6 in order on switch 2. + SW3[7:1] refers to bits labeled 7 through 1 in order on switch 3. + SW3[1:8]= 0000_0001 refers to bits labeled 1 through 6 is set as "On" + and bits labeled 8 is set as "Off". + +1.1 There are three type boards for MPC8360E silicon up to now, They are + + * MPC8360E-MDS-PB PROTO (a.k.a 8360SYS PROTOTYPE) + * MPC8360E-MDS-PB PILOT (a.k.a 8360SYS PILOT) + * MPC8360EA-MDS-PB PROTO (a.k.a 8360SYS2 PROTOTYPE) + +1.2 For all the MPC8360EMDS Board + + First, make sure the board default setting is consistent with the + document shipped with your board. Then apply the following setting: + SW3[1-8]= 0000_0100 (HRCW setting value is performed on local bus) + SW4[1-8]= 0011_0000 (Flash boot on local bus) + SW9[1-8]= 0110_0110 (PCI Mode enabled. HRCW is read from FLASH) + SW10[1-8]= 0000_1000 (core PLL setting) + SW11[1-8]= 0000_0100 (SW11 is on the another side of the board) + JP6 1-2 + on board Oscillator: 66M + +1.3 Since different board/chip rev. combinations have AC timing issues, + u-boot forces RGMII-ID (RGMII with Internal Delay) mode on by default + by the patch (mpc83xx: Disable G1TXCLK, G2TXCLK h/w buffers). + + When the rev2.x silicon mount on these boards, and if you are using + u-boot version after this patch, to make the ethernet interfaces usable, + and to enable RGMII-ID on your board, you have to setup the jumpers + correctly. + + * MPC8360E-MDS-PB PROTO + nothing to do + * MPC8360E-MDS-PB PILOT + JP9 and JP8 should be ON + * MPC8360EA-MDS-PB PROTO + JP2 and JP3 should be ON + +2. Memory Map + +2.1. The memory map should look pretty much like this: + + 0x0000_0000 0x7fff_ffff DDR 2G + 0x8000_0000 0x8fff_ffff PCI MEM prefetch 256M + 0x9000_0000 0x9fff_ffff PCI MEM non-prefetch 256M + 0xc000_0000 0xdfff_ffff Empty 512M + 0xe000_0000 0xe01f_ffff Int Mem Reg Space 2M + 0xe020_0000 0xe02f_ffff Empty 1M + 0xe030_0000 0xe03f_ffff PCI IO 1M + 0xe040_0000 0xefff_ffff Empty 252M + 0xf000_0000 0xf3ff_ffff Local Bus SDRAM 64M + 0xf400_0000 0xf7ff_ffff Empty 64M + 0xf800_0000 0xf800_7fff BCSR on CS1 32K + 0xf800_8000 0xf800_ffff PIB CS4 32K + 0xf801_0000 0xf801_7fff PIB CS5 32K + 0xfe00_0000 0xfeff_ffff FLASH on CS0 16M + + +3. Definitions + +3.1 Explanation of NEW definitions in: + + include/configs/MPC8360EMDS.h + + CONFIG_MPC83xx MPC83xx family for both MPC8349 and MPC8360 + CONFIG_MPC8360 MPC8360 specific + CONFIG_MPC8360EMDS MPC8360EMDS board specific + +4. Compilation + + MPC8360EMDS shipped with 33.33MHz or 66MHz oscillator(check U41 chip). + + Assuming you're using BASH shell: + + export CROSS_COMPILE=your-cross-compile-prefix + cd u-boot + make distclean + make MPC8360EMDS_XX_config + make + + MPC8360EMDS support ATM, PCI in host and slave mode. + + To make u-boot support ATM : + 1) Make MPC8360EMDS_XX_ATM_config + + To make u-boot support PCI host 66M : + 1) DIP SW support PCI mode as described in Section 1.1. + 2) Make MPC8360EMDS_XX_HOST_66_config + + To make u-boot support PCI host 33M : + 1) DIP SW setting is similar as Section 1.1, except for SW3[4] is 1 + 2) Make MPC8360EMDS_XX_HOST_33_config + + To make u-boot support PCI slave 66M : + 1) DIP SW setting is similar as Section 1.1, except for SW9[3] is 1 + 2) Make MPC8360EMDS_XX_SLAVE_config + + (where XX is: + 33 - 33.33MHz oscillator + 66 - 66MHz oscillator) + +5. Downloading and Flashing Images + +5.0 Download over serial line using Kermit: + + loadb + [Drop to kermit: + ^\c + send + c + ] + + + Or via tftp: + + tftp 10000 u-boot.bin + +5.1 Reflash U-boot Image using U-boot + + tftp 20000 u-boot.bin + protect off fef00000 fef3ffff + erase fef00000 fef3ffff + + cp.b 20000 fef00000 xxxx + + or + + cp.b 20000 fef00000 3ffff + + +You have to supply the correct byte count with 'xxxx' from the TFTP result log. +Maybe 3ffff will work too, that corresponds to the erased sectors. + + +6. Notes + 1) The console baudrate for MPC8360EMDS is 115200bps. diff --git a/board/freescale/mpc837xemds/README b/board/freescale/mpc837xemds/README new file mode 100644 index 0000000000..faf21c9ffb --- /dev/null +++ b/board/freescale/mpc837xemds/README @@ -0,0 +1,104 @@ +Freescale MPC837xEMDS Board +----------------------------------------- +1. Board Switches and Jumpers +1.0 There are four Dual-In-Line Packages(DIP) Switches on MPC837xEMDS board + For some reason, the HW designers describe the switch settings + in terms of 0 and 1, and then map that to physical switches where + the label "On" refers to logic 0 and "Off" is logic 1. + + Switch bits are numbered 1 through, like, 4 6 8 or 10, but the + bits may contribute to signals that are numbered based at 0, + and some of those signals may be high-bit-number-0 too. Heed + well the names and labels and do not get confused. + + "Off" == 1 + "On" == 0 + + SW4[8] is the bit labeled 8 on Switch 4. + SW2[1:6] refers to bits labeled 1 through 6 in order on switch 2. + SW2[1:8]= 0000_0001 refers to bits labeled 1 through 7 is set as "On" + and bits labeled 8 is set as "Off". + +1.1 For the MPC837xEMDS Processor Board + + First, make sure the board default setting is consistent with the + document shipped with your board. Then apply the following setting: + SW3[1-8]= 0011_0000 (BOOTSEQ, ROMLOC setting) + SW4[1-8]= 0000_0110 (core PLL setting) + SW5[1-8]= 1001_1000 (system PLL, boot up from low end of flash) + SW6[1-8]= 0000_1000 (HRCW is read from NOR FLASH) + SW7[1-8]= 0110_1101 (TSEC1/2 interface setting - RGMII) + J3 2-3, TSEC1 LVDD1 with 2.5V + J6 2-3, TSEC2 LVDD2 with 2.5V + J9 2-3, CLKIN from osc on board + J10 removed, CS0 connect to NOR flash; when mounted, CS0 connect to NAND + J11 removed, Hardware Reset Configuration Word load from FLASH(NOR or NAND) + mounted, HRCW load from BCSR. + + on board Oscillator: 66M + +2. Memory Map + +2.1. The memory map should look pretty much like this: + + 0x0000_0000 0x7fff_ffff DDR 2G + 0x8000_0000 0x8fff_ffff PCI MEM prefetch 256M + 0x9000_0000 0x9fff_ffff PCI MEM non-prefetch 256M + 0xc000_0000 0xdfff_ffff Empty 512M + 0xe000_0000 0xe00f_ffff Int Mem Reg Space 1M + 0xe010_0000 0xe02f_ffff Empty 2M + 0xe030_0000 0xe03f_ffff PCI IO 1M + 0xe040_0000 0xe05f_ffff Empty 2M + 0xe060_0000 0xe060_7fff NAND Flash 32K + 0xf400_0000 0xf7ff_ffff Empty 64M + 0xf800_0000 0xf800_7fff BCSR on CS1 32K + 0xfe00_0000 0xffff_ffff NOR Flash on CS0 32M + +3. Definitions + +3.1 Explanation of NEW definitions in: + + include/configs/MPC837XEMDS.h + + CONFIG_MPC83xx MPC83xx family for both MPC837x and MPC8360 + CONFIG_MPC837x MPC837x specific + CONFIG_MPC837XEMDS MPC837XEMDS board specific + +4. Compilation + + Assuming you're using BASH shell: + + export CROSS_COMPILE=your-cross-compile-prefix + cd u-boot + make distclean + make MPC837XEMDS_config + make + +5. Downloading and Flashing Images + +5.0 Download over serial line using Kermit: + + loadb + [Drop to kermit: + ^\c + send + c + ] + + + Or via tftp: + + tftp 40000 u-boot.bin + +5.1 Reflash U-boot Image using U-boot + + tftp 40000 u-boot.bin + protect off fe000000 fe1fffff + erase fe000000 fe1fffff + + cp.b 40000 fe000000 xxxx + +You have to supply the correct byte count with 'xxxx' from the TFTP result log. + +6. Notes + 1) The console baudrate for MPC837XEMDS is 115200bps. diff --git a/board/freescale/mpc837xerdb/README b/board/freescale/mpc837xerdb/README new file mode 100644 index 0000000000..cfb6efa27e --- /dev/null +++ b/board/freescale/mpc837xerdb/README @@ -0,0 +1,97 @@ +Freescale MPC837xE-RDB Board +----------------------------------------- + +1. Board Description + + The MPC837xE-RDB are reference boards featuring the Freescale MPC8377E, + MPC8378E, and the MPC8379E processors in a Mini-ITX form factor. + + The MPC837xE-RDB's have the following common features: + + A) 256-MBytes on-board DDR2 unbuffered SDRAM + B) 8-Mbytes NOR Flash + C) 32-MBytes NAND Flash + D) 1 Secure Digital High Speed Card (SDHC) Interface + E) 1 Gigabit Ethernet + F) 5-port Ethernet switch (Vitesse 7385) + G) 1 32-bit, 3.3 V, PCI slot + H) 1 32-bit, 3.3 V, Mini-PCI slot + I) 4-port USB 2.0 Hub + J) 1-port OTG USB + K) 2 serial ports (top main console) + L) on board Oscillator: 66M + + The MPC837xE-RDB's have the following differences: + + MPC8377E-RDB MPC8378E-RDB MPC8379E-RDB + SATA controllers 2 0 4 + PCI-Express (mini) 2 2 0 + SGMII Ports 0 2 0 + + +2. Memory Map + +2.1. The memory map should look pretty much like this: + + Address Range Device Size Port Size + (Bytes) (Bits) + =========================== ================= ======= ========= + 0x0000_0000 0x0fff_ffff DDR 256M 64 + 0x1000_0000 0x7fff_ffff Empty 1.75G - + 0x8000_0000 0x8fff_ffff PCI MEM prefetch 256M 32 + 0x9000_0000 0x9fff_ffff PCI MEM non-prefetch 256M 32 + 0xe030_0000 0xe03f_ffff PCI I/O space 1M 32 + 0xe000_0000 0xe00f_ffff Int Mem Reg Space 1M - + 0xe060_0000 0xe060_7fff NAND Flash 32K 8 + 0xfe00_0000 0xfe7f_ffff NOR Flash on CS0 8M 16 + + +3. Definitions + +3.1 Explanation of NEW definitions in: + + include/configs/MPC837XERDB.h + + CONFIG_MPC83xx MPC83xx family for both MPC8349 and MPC8360 + CONFIG_MPC837x MPC837x specific + CONFIG_MPC837XERDB MPC837xE-RDB board specific + + +4. Compilation + + Assuming you're using BASH shell: + + export CROSS_COMPILE=your-cross-compile-prefix + cd u-boot + make distclean + make MPC837XERDB_config + make + + +5. Downloading and Flashing Images + +5.0 Download over serial line using Kermit: + + loadb $loadaddr + [Drop to kermit: + ^\c + send + c + ] + + + Or via tftp: + + tftp $loadaddr u-boot.bin + +5.1 Reflash U-boot Image using U-boot + + tftp $loadaddr u-boot.bin + protect off fe000000 fe0fffff + erase fe000000 fe0fffff + cp.b $loadaddr fe000000 $filesize + + +6. Additional Notes: + 1) The console is connected to the top RS-232 connector and the + baudrate for MPC837XE-RDB is 115200bps. diff --git a/board/freescale/mpc8536ds/README b/board/freescale/mpc8536ds/README new file mode 100644 index 0000000000..2a38bd6dda --- /dev/null +++ b/board/freescale/mpc8536ds/README @@ -0,0 +1,127 @@ +Overview: +========= + +The MPC8536E integrates a PowerPC processor core with system logic +required for imaging, networking, and communications applications. + +Boot from NAND: +=============== + +The MPC8536E is capable of booting from NAND flash which uses the image +u-boot-nand.bin. This image contains two parts: a first stage image(also +call 4K NAND loader and a second stage image. The former is appended to +the latter to produce u-boot-nand.bin. + +The bootup process can be divided into two stages: the first stage will +configure the L2SRAM, then copy the second stage image to L2SRAM and jump +to it. The second stage image is to configure all the hardware and boot up +to U-Boot command line. + +The 4K NAND loader's code comes from the corresponding nand_spl directory, +along with the code twisted by CONFIG_NAND_SPL. The macro CONFIG_NAND_SPL +is mainly used to shrink the code size to the 4K size limitation. + +The macro CONFIG_SYS_RAMBOOT is used to control the code to produce the +second stage image. It's set in the board config file when boot from NAND +is selected. + +Build and boot steps +-------------------- + +1. Building image + make MPC8536DS_NAND_config + make CROSS_COMPILE=powerpc-none-linux-gnuspe- all + +2. Change dip-switch + SW2[5-8] = 1011 + SW9[1-3] = 101 + Note: 1 stands for 'on', 0 stands for 'off' + +3. Flash image + tftp 1000000 u-boot-nand.bin + nand erase 0 a0000 + nand write 1000000 0 a0000 + +Boot from On-chip ROM: +====================== + +The MPC8536E is capable of booting from the on-chip ROM - boot from eSDHC +and boot from eSPI. When power on, the porcessor excutes the ROM code to +initialize the eSPI/eSDHC controller, and loads the mian U-Boot image from +the memory device that interfaced to the controller, such as the SDCard or +SPI EEPROM, to the target memory, e.g. SDRAM or L2SRAM, then boot from it. + +The memory device should contain a specific data structure with control word +and config word at the fixed address. The config word direct the process how +to config the memory device, and the control word direct the processor where +to find the image on the memory device, or where copy the main image to. The +user can use any method to store the data structure to the memory device, only +if store it on the assigned address. + +Build and boot steps +-------------------- + +For boot from eSDHC: +1. Build image + make MPC8536DS_SDCARD_config + make CROSS_COMPILE=powerpc-none-linux-gnuspe- all + +2. Change dip-switch + SW2[5-8] = 0111 + SW3[1] = 0 + SW8[7] = 0 - The on-board SD/MMC slot is active + SW8[7] = 1 - The externel SD/MMC slot is active + +3. Put image to SDCard + Put the follwing info at the assigned address on the SDCard: + + Offset | Data | Description + -------------------------------------------------------- + | 0x40-0x43 | 0x424F4F54 | BOOT signature | + -------------------------------------------------------- + | 0x48-0x4B | 0x00080000 | u-boot.bin's size | + -------------------------------------------------------- + | 0x50-0x53 | 0x???????? | u-boot.bin's Addr on SDCard | + -------------------------------------------------------- + | 0x58-0x5B | 0xF8F80000 | Target Address | + ------------------------------------------------------- + | 0x60-0x63 | 0xF8FFF000 | Execution Starting Address | + -------------------------------------------------------- + | 0x68-0x6B | 0x6 | Number of Config Addr/Data | + -------------------------------------------------------- + | 0x80-0x83 | 0xFF720100 | Config Addr 1 | + | 0x84-0x87 | 0xF8F80000 | Config Data 1 | + -------------------------------------------------------- + | 0x88-0x8b | 0xFF720e44 | Config Addr 2 | + | 0x8c-0x8f | 0x0000000C | Config Data 2 | + -------------------------------------------------------- + | 0x90-0x93 | 0xFF720000 | Config Addr 3 | + | 0x94-0x97 | 0x80010000 | Config Data 3 | + -------------------------------------------------------- + | 0x98-0x9b | 0xFF72e40c | Config Addr 4 | + | 0x9c-0x9f | 0x00000040 | Config Data 4 | + -------------------------------------------------------- + | 0xa0-0xa3 | 0x40000001 | Config Addr 5 | + | 0xa4-0xa7 | 0x00000100 | Config Data 5 | + -------------------------------------------------------- + | 0xa8-0xab | 0x80000001 | Config Addr 6 | + | 0xac-0xaf | 0x80000001 | Config Data 6 | + -------------------------------------------------------- + | ...... | + -------------------------------------------------------- + | 0x???????? | u-boot.bin | + -------------------------------------------------------- + + then insert the SDCard to the active slot to boot up. + +For boot from eSPI: +1. Build image + make MPC8536DS_SPIFLASH_config + make CROSS_COMPILE=powerpc-none-linux-gnuspe- all + +2. Change dip-switch + SW2[5-8] = 0110 + +3. Put image to SPI flash + Put the info in the above table onto the SPI flash, then + boot up. diff --git a/board/freescale/mpc8544ds/README b/board/freescale/mpc8544ds/README new file mode 100644 index 0000000000..b49c3c07c4 --- /dev/null +++ b/board/freescale/mpc8544ds/README @@ -0,0 +1,122 @@ +Overview +-------- +The MPC8544DS system is similar to the 85xx CDS systems such +as the MPC8548CDS due to the similar E500 core. However, it +is placed on the same board as the 8641 HPCN system. + + +Flash Banks +----------- +Like the 85xx CDS systems, the 8544 DS board has two flash banks. +They are both present on boot, but there locations can be swapped +using the dip-switch SW10, bit 2. + +However, unlike the CDS systems, but similar to the 8641 HPCN +board, a runtime reset through the FPGA can also affect a swap +on the flash bank mappings for the next reset cycle. + +Irrespective of the switch SW10[2], booting is always from the +boot bank at 0xfff8_0000. + + +Memory Map +---------- + +0xff80_0000 - 0xffbf_ffff Alternate bank 4MB +0xffc0_0000 - 0xffff_ffff Boot bank 4MB + +0xffb8_0000 Alternate image start 512KB +0xfff8_0000 Boot image start 512KB + + +Flashing Images +--------------- + +For example, to place a new image in the alternate flash bank +and then reset with that new image temporarily, use this: + + tftp 1000000 u-boot.bin.8544ds + erase ffb80000 ffbfffff + cp.b 1000000 ffb80000 80000 + pixis_reset altbank + + +To overwrite the image in the boot flash bank: + + tftp 1000000 u-boot.bin.8544ds + protect off all + erase fff80000 ffffffff + cp.b 1000000 fff80000 80000 + +Other example U-Boot image and flash manipulations examples +can be found in the README.mpc85xxcds file as well. + + +The pixis_reset command +----------------------- +A new command, "pixis_reset", is introduced to reset mpc8641hpcn board +using the FPGA sequencer. When the board restarts, it has the option +of using either the current or alternate flash bank as the boot +image, with or without the watchdog timer enabled, and finally with +or without frequency changes. + +Usage is; + + pixis_reset + pixis_reset altbank + pixis_reset altbank wd + pixis_reset altbank cf + pixis_reset cf + +Examples; + + /* reset to current bank, like "reset" command */ + pixis_reset + + /* reset board but use the to alternate flash bank */ + pixis_reset altbank + + /* reset board, use alternate flash bank with watchdog timer enabled*/ + pixis_reset altbank wd + + /* reset board to alternate bank with frequency changed. + * 40 is SYSCLK, 2.5 is COREPLL ratio, 10 is MPXPLL ratio + */ + pixis-reset altbank cf 40 2.5 10 + +Valid clock choices are in the 8641 Reference Manuals. + + +Using the Device Tree Source File +--------------------------------- +To create the DTB (Device Tree Binary) image file, +use a command similar to this: + + dtc -b 0 -f -I dts -O dtb mpc8544ds.dts > mpc8544ds.dtb + +Likely, that .dts file will come from here; + + linux-2.6/arch/powerpc/boot/dts/mpc8544ds.dts + +After placing the DTB file in your TFTP disk area, +you can download that dtb file using a command like: + + tftp 900000 mpc8544ds.dtb + +Burn it to flash if you want. + + +Booting Linux +------------- + +Place a linux uImage in the TFTP disk area too. + + tftp 1000000 uImage.8544 + tftp 900000 mpc8544ds.dtb + bootm 1000000 - 900000 + +Watch your ethact, netdev and bootargs U-Boot environment variables. +You may want to do something like this too: + + setenv ethact eTSEC3 + setenv netdev eth1 diff --git a/board/freescale/mpc8569mds/README b/board/freescale/mpc8569mds/README new file mode 100644 index 0000000000..3d12a964cd --- /dev/null +++ b/board/freescale/mpc8569mds/README @@ -0,0 +1,77 @@ +Overview +-------- +MPC8569MDS is composed of two boards - PB (Processor Board) and PIB (Platform +I/O Board). The mpc8569 PowerTM processor is mounted on PB board. + +Building U-boot +----------- + make MPC8569MDS_config + make + +Memory Map +---------- +0x0000_0000 0x7fff_ffff DDR 2G +0xa000_0000 0xbfff_ffff PCIe MEM 512MB +0xe000_0000 0xe00f_ffff CCSRBAR 1M +0xe280_0000 0xe2ff_ffff PCIe I/O 8M +0xc000_0000 0xdfff_ffff SRIO 512MB +0xf000_0000 0xf3ff_ffff SDRAM 64MB +0xf800_0000 0xf800_7fff BCSR 32KB +0xf800_8000 0xf800_ffff PIB (CS4) 32KB +0xf801_0000 0xf801_7fff PIB (CS5) 32KB +0xfe00_0000 0xffff_ffff Flash 32MB + + +Flashing u-boot Images +--------------- + +Use the following commands to program u-boot image into flash: + + => tftp 1000000 u-boot.bin + => protect off all + => erase fff80000 ffffffff + => cp.b 1000000 fff80000 80000 + + +Setting the correct MAC addresses +----------------------- +The command - "mac", is introduced to set on-board system EEPROM in the format +defined in board/freescale/common/sys_eeprom.c. we must set all 8 MAC +addresses for the MPC8569MDS's 8 Ethernet ports and save it by "mac save" when +we first get the board. The commands are as follows: + => mac i NXID /* Set NXID to this EEPROM */ + => mac e 01 /* Set Errata, this value is not defined by hardware + designer, we can set whatever we want */ + => mac n a0 /* Set Serial Number. This is not defined by hardware + designer, we can set whatever we want */ + => mac date 090512080000 /* Set the date in YYMMDDhhmmss format */ + + => mac p 8 /* Set the number of mac ports, it should be 8 */ + => mac 0 xx:xx:xx:xx:xx:xx /* xx:xx:xx:xx:xx:xx should be the real mac + address, you can refer to the value on + the sticker of the rear side of the board + */ + ..... + => mac 7 xx:xx:xx:xx:xx:xx + => mac read + => mac save + +After resetting the board, the ethxaddrs will be filled with the mac addresses +if such environment variables are blank(never been set before). If the ethxaddr +has been set but we want to update it, we can use the following commands: + => setenv ethxaddr /* x = "none",1,2,3,4,5,6,7 */ + => save + => reset + + +Programming the ucode to flash +--------------------------------- +MPC8569 doesn't have ROM in QE, so we must upload the microcode(ucode) to QE's +IRAM so that the QE can work. The ucode binary can be downloaded from +http://opensource.freescale.com/firmware/, and it must be programmed to +the address 0xfff0000 in the flash. Otherwise, the QE can't work and uboot +hangs at "Net:" + + +Please note the above two steps(setting mac addresses and programming ucode) are +very important to get the board booting up and working properly. diff --git a/board/freescale/mpc8572ds/README b/board/freescale/mpc8572ds/README new file mode 100644 index 0000000000..57fd2ad616 --- /dev/null +++ b/board/freescale/mpc8572ds/README @@ -0,0 +1,166 @@ +Overview +-------- +MPC8572DS is a high-performance computing, evaluation and development platform +supporting the mpc8572 PowerTM processor. + +Building U-boot +----------- + make MPC8572DS_config + make + +Flash Banks +----------- +MPC8572DS board has two flash banks. They are both present on boot, but their +locations can be swapped using the dip-switch SW9[1:2]. + +Booting is always from the boot bank at 0xec00_0000. + + +Memory Map +---------- + +0xe800_0000 - 0xebff_ffff Alternate bank 64MB +0xec00_0000 - 0xefff_ffff Boot bank 64MB + +0xebf8_0000 - 0xebff_ffff Alternate u-boot address 512KB +0xeff8_0000 - 0xefff_ffff Boot u-boot address 512KB + + +Flashing Images +--------------- + +To place a new u-boot image in the alternate flash bank and then reset with that + new image temporarily, use this: + + tftp 1000000 u-boot.bin + erase ebf80000 ebffffff + cp.b 1000000 ebf80000 80000 + pixis_reset altbank + + +To program the image in the boot flash bank: + + tftp 1000000 u-boot.bin + protect off all + erase eff80000 ffffffff + cp.b 1000000 eff80000 80000 + + +The pixis_reset command +----------------------- +The command - "pixis_reset", is introduced to reset mpc8572ds board +using the FPGA sequencer. When the board restarts, it has the option +of using either the current or alternate flash bank as the boot +image, with or without the watchdog timer enabled, and finally with +or without frequency changes. + +Usage is; + + pixis_reset + pixis_reset altbank + pixis_reset altbank wd + pixis_reset altbank cf + pixis_reset cf + +Examples: + + /* reset to current bank, like "reset" command */ + pixis_reset + + /* reset board but use the to alternate flash bank */ + pixis_reset altbank + + +Using the Device Tree Source File +--------------------------------- +To create the DTB (Device Tree Binary) image file, +use a command similar to this: + + dtc -b 0 -f -I dts -O dtb mpc8572ds.dts > mpc8572ds.dtb + +Likely, that .dts file will come from here; + + linux-2.6/arch/powerpc/boot/dts/mpc8572ds.dts + + +Booting Linux +------------- + +Place a linux uImage in the TFTP disk area. + + tftp 1000000 uImage.8572 + tftp c00000 mpc8572ds.dtb + bootm 1000000 - c00000 + + +Implementing AMP(Asymmetric MultiProcessing) +------------- +1. Build kernel image for core0: + + a. $ make 85xx/mpc8572_ds_defconfig + + b. $ make menuconfig + - un-select "Processor support"->"Symetric multi-processing support" + + c. $ make uImage + + d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core0 + +2. Build kernel image for core1: + + a. $ make 85xx/mpc8572_ds_defconfig + + b. $ make menuconfig + - Un-select "Processor support"->"Symetric multi-processing support" + - Select "Advanced setup" -> " Prompt for advanced kernel + configuration options" + - Select "Set physical address where the kernel is loaded" and + set it to 0x20000000, assuming core1 will start from 512MB. + - Select "Set custom page offset address" + - Select "Set custom kernel base address" + - Select "Set maximum low memory" + - "Exit" and save the selection. + + c. $ make uImage + + d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core1 + +3. Create dtb for core0: + + $ dtc -I dts -O dtb -f -b 0 arch/powerpc/boot/dts/mpc8572ds_core0.dts > /tftpboot/mpc8572ds_core0.dtb + +4. Create dtb for core1: + + $ dtc -I dts -O dtb -f -b 1 arch/powerpc/boot/dts/mpc8572ds_core1.dts > /tftpboot/mpc8572ds_core1.dtb + +5. Bring up two cores separately: + + a. Power on the board, under u-boot prompt: + => setenv + => setenv + => setenv bootargs root=/dev/ram rw console=ttyS0,115200 + b. Bring up core1's kernel first: + => setenv bootm_low 0x20000000 + => setenv bootm_size 0x10000000 + => tftp 21000000 8572/uImage.core1 + => tftp 22000000 8572/ramdiskfile + => tftp 20c00000 8572/mpc8572ds_core1.dtb + => interrupts off + => bootm start 21000000 22000000 20c00000 + => bootm loados + => bootm ramdisk + => bootm fdt + => fdt boardsetup + => fdt chosen $initrd_start $initrd_end + => bootm prep + => cpu 1 release $bootm_low - $fdtaddr - + c. Bring up core0's kernel(on the same u-boot console): + => setenv bootm_low 0 + => setenv bootm_size 0x20000000 + => tftp 1000000 8572/uImage.core0 + => tftp 2000000 8572/ramdiskfile + => tftp c00000 8572/mpc8572ds_core0.dtb + => bootm 1000000 2000000 c00000 + +Please note only core0 will run u-boot, core1 starts kernel directly after +"cpu release" command is issued. diff --git a/board/freescale/mpc8610hpcd/README b/board/freescale/mpc8610hpcd/README new file mode 100644 index 0000000000..31a9af3fee --- /dev/null +++ b/board/freescale/mpc8610hpcd/README @@ -0,0 +1,73 @@ +Freescale MPC8610HPCD board +=========================== + + +Building U-Boot +--------------- + + $ make MPC8610HPCD_config + Configuring for MPC8610HPCD board... + + $ make + + +Flashing U-Boot +--------------- +The flash is 128M starting at 0xF800_0000. + +The alternate image is at 0xFBF0_0000 +The boot image is at 0xFFF0_0000. + + +To Flash U-Boot into the booting bank: + + tftp 1000000 u-boot.bin + protect off all + erase fff00000 +$filesize + cp.b 1000000 fff00000 $filesize + + +To Flash U-boot into the alternate bank + + tftp 1000000 u-boot.bin + erase fbf00000 +$filesize + cp.b 1000000 fbf00000 $filesize + + +pixis_reset command +------------------- +A new command, "pixis_reset", is introduced to reset mpc8610hpcd board +using the FPGA sequencer. When the board restarts, it has the option +of using either the current or alternate flash bank as the boot +image, with or without the watchdog timer enabled, and finally with +or without frequency changes. + +Usage is; + + pixis_reset + pixis_reset altbank + pixis_reset altbank wd + pixis_reset altbank cf + pixis_reset cf + +Examples; + + /* reset to current bank, like "reset" command */ + pixis_reset + + /* reset board but use the to alternate flash bank */ + pixis_reset altbank + + /* reset board, use alternate flash bank with watchdog timer enabled*/ + pixis_reset altbank wd + + /* reset board to alternate bank with frequency changed. + * 40 is SYSCLK, 2.5 is COREPLL ratio, 10 is MPXPLL ratio + */ + pixis-reset altbank cf 40 2.5 10 + + +DIP Switch Settings +------------------- +To manually switch the flash banks using the DIP switch +settings, toggle both SW6:1 and SW6:2. diff --git a/board/freescale/mpc8641hpcn/README b/board/freescale/mpc8641hpcn/README new file mode 100644 index 0000000000..d8fe0a4a13 --- /dev/null +++ b/board/freescale/mpc8641hpcn/README @@ -0,0 +1,186 @@ +Freescale MPC8641HPCN board +=========================== + +Created 05/24/2006 Haiying Wang +------------------------------- + +1. Building U-Boot +------------------ +The 86xx HPCN code base is known to compile using: + Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3 + + $ make MPC8641HPCN_config + Configuring for MPC8641HPCN board... + + $ make + + +2. Switch and Jumper Setting +---------------------------- +Jumpers: + J14 Pins 1-2 (near plcc32 socket) + +Switches: + SW1(1-5) = 01100 CONFIG_SYS_COREPLL = 01000 :: CORE = 2:1 + 01100 :: CORE = 2.5:1 + 10000 :: CORE = 3:1 + 11100 :: CORE = 3.5:1 + 10100 :: CORE = 4:1 + 01110 :: CORE = 4.5:1 + SW1(6-8) = 001 CONFIG_SYS_SYSCLK = 000 :: SYSCLK = 33MHz + 001 :: SYSCLK = 40MHz + + SW2(1-4) = 1100 CONFIG_SYS_CCBPLL = 0010 :: 2X + 0100 :: 4X + 0110 :: 6X + 1000 :: 8X + 1010 :: 10X + 1100 :: 12X + 1110 :: 14X + 0000 :: 16X + SW2(5-8) = 1110 CONFIG_SYS_BOOTLOC = 1110 :: boot 16-bit localbus + + SW3(1-7) = 0011000 CONFIG_SYS_VID = 0011000 :: VCORE = 1.2V + 0100000 :: VCORE = 1.11V + SW3(8) = 0 VCC_PLAT = 0 :: VCC_PLAT = 1.2V + 1 :: VCC_PLAT = 1.0V + + SW4(1-2) = 11 CONFIG_SYS_HOSTMODE = 11 :: both prots host/root + SW4(3-4) = 11 CONFIG_SYS_BOOTSEQ = 11 :: no boot seq + SW4(5-8) = 0011 CONFIG_SYS_IOPORT = 0011 :: both PEX + + SW5(1) = 1 CONFIG_SYS_FLASHMAP = 1 :: boot from flash + 0 :: boot from PromJet + SW5(2) = 1 CONFIG_SYS_FLASHBANK = 1 :: swap upper/lower + halves (virtual banks) + 0 :: normal + SW5(3) = 0 CONFIG_SYS_FLASHWP = 0 :: not protected + SW5(4) = 0 CONFIG_SYS_PORTDIV = 1 :: 2:1 for PD4 + 1:1 for PD6 + SW5(5-6) = 11 CONFIG_SYS_PIXISOPT = 11 :: s/w determined + SW5(7-8) = 11 CONFIG_SYS_LADOPT = 11 :: s/w determined + + SW6(1) = 1 CONFIG_SYS_CPUBOOT = 1 :: no boot holdoff + SW6(2) = 1 CONFIG_SYS_BOOTADDR = 1 :: no traslation + SW6(3-5) = 000 CONFIG_SYS_REFCLKSEL = 000 :: 100MHZ + SW6(6) = 1 CONFIG_SYS_SERROM_ADDR= 1 :: + SW6(7) = 1 CONFIG_SYS_MEMDEBUG = 1 :: + SW6(8) = 1 CONFIG_SYS_DDRDEBUG = 1 :: + + SW8(1) = 1 ACZ_SYNC = 1 :: 48MHz on TP49 + SW8(2) = 1 ACB_SYNC = 1 :: THRMTRIP disabled + SW8(3) = 1 ACZ_SDOUT = 1 :: p4 mode + SW8(4) = 1 ACB_SDOUT = 1 :: PATA freq. = 133MHz + SW8(5) = 0 SUSLED = 0 :: SouthBridge Mode + SW8(6) = 0 SPREAD = 0 :: REFCLK SSCG Disabled + SW8(7) = 1 ACPWR = 1 :: non-battery + SW8(8) = 0 CONFIG_SYS_IDWP = 0 :: write enable + + +3. Flash U-Boot +--------------- +The flash range 0xEF800000 to 0xEFFFFFFF can be divided into 2 halves. +It is possible to use either half to boot using u-boot. Switch 5 bit 2 +is used for this purpose. + +0xEF800000 to 0xEFBFFFFF - 4MB +0xEFC00000 to 0xEFFFFFFF - 4MB +When this bit is 0, U-Boot is at 0xEFF00000. +When this bit is 1, U-Boot is at 0xEFB00000. + +Use the above mentioned flash commands to program the other half, and +use switch 5, bit 2 to alternate between the halves. Note: The booting +version of U-Boot will always be at 0xEFF00000. + +To Flash U-Boot into the booting bank (0xEFC00000 - 0xEFFFFFFF): + + tftp 1000000 u-boot.bin + protect off all + erase eff00000 +$filesize + cp.b 1000000 eff00000 $filesize + +or use tftpflash command: + run tftpflash + +To Flash U-boot into the alternative bank (0xEF800000 - 0xEFBFFFFF): + + tftp 1000000 u-boot.bin + erase efb00000 +$filesize + cp.b 1000000 efb00000 $filesize + + +4. Memory Map +------------- +NOTE: RIO and PCI are mutually exclusive, so they share an address + +For 32-bit u-boot, devices are mapped so that the virtual address == +the physical address, and the map looks liks this: + + Memory Range Device Size + ------------ ------ ---- + 0x0000_0000 0x7fff_ffff DDR 2G + 0x8000_0000 0x9fff_ffff RIO MEM 512M + 0x8000_0000 0x9fff_ffff PCI1/PEX1 MEM 512M + 0xa000_0000 0xbfff_ffff PCI2/PEX2 MEM 512M + 0xffe0_0000 0xffef_ffff CCSR 1M + 0xffdf_0000 0xffdf_7fff PIXIS 8K + 0xffdf_8000 0xffdf_ffff CF 8K + 0xf840_0000 0xf840_3fff Stack space 32K + 0xffc0_0000 0xffc0_ffff PCI1/PEX1 IO 64K + 0xffc1_0000 0xffc1_ffff PCI2/PEX2 IO 64K + 0xef80_0000 0xefff_ffff Flash 8M + +For 36-bit-enabled u-boot, the virtual map is the same as for 32-bit. +However, the physical map is altered to reside in 36-bit space, as follows. +Addresses are no longer mapped with VA == PA. All accesses from +software use the VA; the PA is only used for setting up windows +and mappings. Note that with the exception of PCI MEM and RIO, the low + 32 bits are the same as the VA above; only the top 4 bits vary: + + Memory Range Device Size + ------------ ------ ---- + 0x0_0000_0000 0x0_7fff_ffff DDR 2G + 0xc_0000_0000 0xc_1fff_ffff RIO MEM 512M + 0xc_0000_0000 0xc_1fff_ffff PCI1/PEX1 MEM 512M + 0xc_2000_0000 0xc_3fff_ffff PCI2/PEX2 MEM 512M + 0xf_ffe0_0000 0xf_ffef_ffff CCSR 1M + 0xf_ffdf_0000 0xf_ffdf_7fff PIXIS 8K + 0xf_ffdf_8000 0xf_ffdf_ffff CF 8K + 0x0_f840_0000 0xf_f840_3fff Stack space 32K + 0xf_ffc0_0000 0xf_ffc0_ffff PCI1/PEX1 IO 64K + 0xf_ffc1_0000 0xf_ffc1_ffff PCI2/PEX2 IO 64K + 0xf_ef80_0000 0xf_efff_ffff Flash 8M + +5. pixis_reset command +-------------------- +A new command, "pixis_reset", is introduced to reset mpc8641hpcn board +using the FPGA sequencer. When the board restarts, it has the option +of using either the current or alternate flash bank as the boot +image, with or without the watchdog timer enabled, and finally with +or without frequency changes. + +Usage is; + + pixis_reset + pixis_reset altbank + pixis_reset altbank wd + pixis_reset altbank cf + pixis_reset cf + +Examples; + + /* reset to current bank, like "reset" command */ + pixis_reset + + /* reset board but use the to alternate flash bank */ + pixis_reset altbank + + /* reset board, use alternate flash bank with watchdog timer enabled*/ + pixis_reset altbank wd + + /* reset board to alternate bank with frequency changed. + * 40 is SYSCLK, 2.5 is COREPLL ratio, 10 is MPXPLL ratio + */ + pixis-reset altbank cf 40 2.5 10 + +Valid clock choices are in the 8641 Reference Manuals. diff --git a/board/freescale/mx35pdk/README b/board/freescale/mx35pdk/README new file mode 100644 index 0000000000..3d69ed5839 --- /dev/null +++ b/board/freescale/mx35pdk/README @@ -0,0 +1,188 @@ +Overview +-------------- + +mx35pdk (known als as mx35_3stack) is a development board by Freescale. +It consists of three pluggable board: + - CPU module, with CPU, RAM, flash + - Personality board, with most interfaces (USB, Network,..) + - Debug board with JTAG header. + +The board is usually delivered with redboot. This howto explains how to boot +a linux kernel and how to replace the original bootloader with U-Boot. + +The board is delivered with Redboot on the NAND flash. It is possible to +switch the boot device with the switches SW1-SW2 on the Personality board, +and with SW5-SW10 on the Debug board. + +Delivered Redboot script to start the kernel +--------------------------------------------------- + +In redboot the following script is stored: + +fis load kernel +exec -c "noinitrd console=ttymxc0,115200 root=/dev/mtdblock8 rw rootfstype=jffs2 ip=dhcp fec_mac=00:04:9F:00:E7:76" + +Kernel is taken from flash. The image is in zImage format. + +Booting from NET, rootfs on NFS: +----------------------------------- + +To change the script in redboot: + +load -r -b 0x100000 +exec -c "noinitrd console=ttymxc0,115200 root=/dev/nfsroot rootfstype=nfsroot nfsroot=192.168.1.1:/opt/eldk-4.2-arm/armVFP rw ip=dhcp" + +If the ip address is not set, you can set it with : + +ip_address -l -h + +Linux partitions: +--------------------------- + +As default, the board is shipped with these partition tables for NAND +and for NOR: + +Creating 5 MTD partitions on "NAND 2GiB 3,3V 8-bit": +0x00000000-0x00100000 : "nand.bootloader" +0x00100000-0x00600000 : "nand.kernel" +0x00600000-0x06600000 : "nand.rootfs" +0x06600000-0x06e00000 : "nand.configure" +0x06e00000-0x80000000 : "nand.userfs" + +Creating 6 MTD partitions on "mxc_nor_flash.0": +0x00000000-0x00080000 : "Bootloader" +0x00080000-0x00480000 : "nor.Kernel" +0x00480000-0x02280000 : "nor.userfs" +0x02280000-0x03e80000 : "nor.rootfs" +0x01fe0000-0x01fe3000 : "FIS directory" +0x01fff000-0x04000000 : "Redboot config" + +NAND partitions can be recognized enabling in kernel CONFIG_MTD_REDBOOT_PARTS. +For this board, CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK should be set to 2. + +However, the setup in redboot is not correct and does not use the whole flash. + +Better solution is to use the kernel parameter mtdparts. +Here the resulting script to be defined in RedBoot with fconfig: + +load -r -b 0x100000 sbabic/mx35pdk/zImage.2.6.37 +exec -c "noinitrd console=ttymxc0,115200 root=/dev/nfsroot rootfstype=nfsroot nfsroot=192.168.1.1:/opt/eldk-4.2-arm/arm rw ip=dhcp mtdparts=mxc_nand:1m(boot),5m(linux),96m(root),8m(cfg),1938m(user);physmap-flash.0:512k(b),4m(k),30m(u),28m(r)" + +Flashing U-Boot +-------------------------------- + +There are two options: the original bootloader in NAND can be replaced with +u-boot, or u-boot can be stored on the NOR flash without erasing +the delivered bootloader. +The boot storage can be select using the switches on the personality board +(SW1-SW2) and on the DEBUG board (SW4-SW10). + +The second option is to be preferred if you have not a JTAG debugger. +If something goes wrong flashing the bootloader, it is always possible to +recover the board booting from the other device. + +Replacing the bootloader on the NAND +-------------------------------------- +To replace RedBoot with U-Boot, the easy way is to do this in linux. +Start the kernel with the suggested options. Make sure to have set the +mtdparts exactly as described, because this matches the layout on the +mx35pdk. + +You should see in your boot log the following entries for the NAND +flash: + +5 cmdlinepart partitions found on MTD device mxc_nand +Creating 5 MTD partitions on "mxc_nand": +0x000000000000-0x000000100000 : "boot" +0x000000100000-0x000000600000 : "linux" +0x000000600000-0x000006600000 : "root" +0x000006600000-0x000006e00000 : "cfg" +0x000006e00000-0x000080000000 : "user" + +You can use the utilities flash_eraseall and nandwrite to put +u-boot on the NAND. The bootloader is marked as "boot", and 1MB is +reserved. If everything is correct, this partition is accessed as +/dev/mtd4. However, check if it is correct with "cat /proc/mtd" and +get the device node from the partition name: + +$ cat /proc/mtd | grep boot + +I suggest you try the utilities on a different partition to be sure +if everything works correctly. If not, and you remove RedBoot, you have to +reinstall it using the ATK tool as suggested by Freescale, or using a +JTAG debugger. + +I report the versions of the utilities I used (they are provided with ELDK): + +-bash-3.2# nandwrite --version +nandwrite $Revision: 1.32 $ + +flash_eraseall --version +flash_eraseall $Revision: 1.22 $ + +nandwrite reports a warning if the file to be saved is not sector aligned. +This should have no consequences, but I preferred to pad u-boot.bin +to get no problem at all. +$ dd if=/dev/zero of=zeros bs=1 count=74800 +$ cat u-boot.bin zeros > u-boot-padded.bin + +To erase the partition: +$ flash_eraseall /dev/mtd4 + +Writing u-boot: + +$ nandwrite /dev/mtd4 u-boot-padded.bin + +Now U-Boot is stored on the booting partition. + +To boot from NAND, you have to select the switches as follows: + +Personality board + SW2 1, 4, 5 on + 2, 3, 6, 7, 8 off + SW1 all off + +Debug Board: + SW5 0 + SW6 0 + SW7 0 + SW8 1 + SW9 1 + SW10 0 + + +Saving U-Boot in the NOR flash +--------------------------------- + +The procedure to save in the NOR flash is quite the same as to write into the NAND. + +Check the partition for boot in the NOR flash. Setting the mtdparts as reported, +the boot partition should be /dev/mtd0. + +Creating 6 MTD partitions on "mxc_nor_flash.0": +0x00000000-0x00080000 : "Bootloader" +0x00080000-0x00480000 : "nor.Kernel" +0x00480000-0x02280000 : "nor.userfs" +0x02280000-0x03e80000 : "nor.rootfs" +0x01fe0000-0x01fe3000 : "FIS directory" +0x01fff000-0x04000000 : "Redboot config" + +To erase the whole partition: +$ flash_eraseall /dev/mtd0 + +Writing u-boot: +dd if=u-boot.bin of=/dev/mtd0 + +To boot from NOR, you have to select the switches as follows: + +Personality board + SW2 all off + SW1 all off + +Debug Board: + SW5 0 + SW6 0 + SW7 0 + SW8 1 + SW9 1 + SW10 0 diff --git a/board/freescale/mx6qsabrelite/README b/board/freescale/mx6qsabrelite/README new file mode 100644 index 0000000000..6f2f5343de --- /dev/null +++ b/board/freescale/mx6qsabrelite/README @@ -0,0 +1,72 @@ +U-Boot for the Freescale i.MX6q SabreLite board + +This file contains information for the port of U-Boot to the Freescale +i.MX6q SabreLite board. + +1. Boot source, boot from SD card +--------------------------------- + +The recent mainline U-Boot for the Freescale i.MX6q SabreLite board supports +boot from SD card only. However, by default, the SabreLite +boards boot from the SPI NOR flash. These boards need to be reflashed with +a small SD card loader to support boot from SD card. This small SD card loader +will be flashed into the SPI NOR. The board will still boot from SPI NOR, but +the loader will in turn request the BootROM to load the U-Boot from SD card. + +The SD card loader is available from + +https://wiki.linaro.org/Boards/MX6QSabreLite + +under a open-source 3-clause BSD license. + +To update the SPI-NOR on the SabreLite board without the Freescale +manufacturing tool use the following procedure: + +1. Write this SD card loader onto a large SD card using: + + sudo dd if=iMX6DQ_SPI_to_uSDHC3.bin of=/dev/sXx + +Note: Replace sXx with the device representing the SD card in your system. + +Note: This writes SD card loader at address 0 + +2. Put this SD card into the slot for the large SD card (SD3 on the bottom of +the board). Make sure SW1 switch is at position "00", so that it can boot +from the fuses. + +3. Power-up the SabreLite, press 'space' to enter command mode in the U-Boot +(the default one the board is shipped with, starting from the SPI NOR) and +enter the following commands: + + MX6Q SABRELITE U-Boot > mmc dev 0 + MX6Q SABRELITE U-Boot > mmc read 0x10800000 0 200 + MX6Q SABRELITE U-Boot > sf probe 1 + MX6Q SABRELITE U-Boot > sf erase 0 0x40000 + MX6Q SABRELITE U-Boot > sf write 0x10800000 0 0x40000 + +4. done. + +In case you somehow do not succeed with this procedure you will have to use +the Freescale manufacturing tool in order to reflash the SPI-NOR. + +Note: The board now boots from full size SD3 on the bottom of the board. NOT + the micro SD4/BOOT slot on the top of the board. I.e. you have to use + full size SD cards. + +This information is taken from + +https://wiki.linaro.org/Boards/MX6QSabreLite + +2. Build +-------- + +To build U-Boot for the SabreLite board: + + make mx6qsabrelite_config + make u-boot.imx + +To copy the resulting u-boot.imx to the SD card: + + sudo dd if=u-boot.imx of=/dev/sXx bs=512 seek=2&&sudo sync + +Note: Replace sXx with the device representing the SD card in your system. diff --git a/board/freescale/p1022ds/README b/board/freescale/p1022ds/README new file mode 100644 index 0000000000..04d9197074 --- /dev/null +++ b/board/freescale/p1022ds/README @@ -0,0 +1,23 @@ +Overview +-------- +P1022ds is a Low End Dual core platform supporting the P1022 processor +of QorIQ series. P1022 is an e500 based dual core SOC. + + +Pin Multiplex(hwconfig setting) +------------------------------- +Add the environment 'usb2', 'audclk' and 'tdm' to support pin multiplex +via hwconfig, i.e: +'setenv hwconfig usb2' to enable USB2 and disable eTsec2 +'setenv hwconfig tdm' to enable TDM and disable Audio +'setenv hwconfig audclk:12' to enable Audio(codec clock sources is 12MHz) + and disable TDM +'setenv hwconfig 'usb2;tdm' to enable USB2 and TDM, disable eTsec2 and Audio +'setenv hwconfig 'usb2;audclk:11' to enable USB2 and Audio(codec clock sources + is 11MHz), disable eTsec2 and TDM + +Warning: TDM and AUDIO can not enable simultaneous ! +and AUDIO codec clock sources only setting as 11MHz or 12MHz ! +'setenv hwconfig 'audclk:12;tdm' --- error ! +'setenv hwconfig 'audclk:11;tdm' --- error ! +'setenv hwconfig 'audclk:10' --- error ! diff --git a/board/freescale/p1023rds/README b/board/freescale/p1023rds/README new file mode 100644 index 0000000000..685f5daa99 --- /dev/null +++ b/board/freescale/p1023rds/README @@ -0,0 +1,101 @@ +Overview +-------- +The P1023 process includes a performance optimized implementation of the +QorIQ data Path Acceleration Architecture (DPAA). This architecture +provides the infrastructure to support simplified sharing of networking +interfaces and accelerators by multiple CPU cores. P1023 is an e500 based +dual core SOC. + +P1023RDS board is a Low End Dual core platform supporting the P1023 +processor of QorIQ series. + +Building U-boot +--------------- +To build the u-boot for P1023RDS: +Configure to NOR boot: + make P1023RDS_config +Configure to NAND boot: + make P1023RDS_NAND_config +Build: + make + +Board Switches +-------------- +Most switches on the board should not be changed. The most frequent +user-settable switches on the board are used to configure +the flash banks. + +J4: all open + +Default NOR flash boot switch setting: + Sw3[1:8]: off on on off on on off off + Sw4[1:8]: off off off on off off off off + Sw6[1:8]: off on off on off on on off + Sw7[1:8]: off on off off on off off off + Sw8[1:8]: on off off off off off off off + +For NAND flash boot,set +Sw4[1:4]: off on on on + +The default native ethernet setting is for RGMII mode. +To use SGMII mode, set +SW8[1:2]: OFF OFF +SW7[6:7]: ON ON + +Memory Map +---------- +0x0000_0000 0x7fff_ffff DDR 2G Cacheable +0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable +0xc000_0000 0xdfff_ffff PCI 512M non-cacheable +0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable + +0xe000_0000 0xe003_ffff BCSR 256K BCSR +0xee00_0000 0xefff_ffff NOR flash 32M NOR flash +0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M +0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable +0xffa0_0000 0xffaf_ffff NAND FLASH 1M non-cacheable +0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 + +Flashing u-boot Images +--------------- +To program the image in the boot flash bank: +NOR flash boot: + => tftp 1000000 u-boot.bin + => protect off all + => erase eff80000 efffffff + => cp.b 1000000 eff80000 80000 + +NAND flash boot: + => tftp 1000000 u-boot-nand.bin + => nand erase 0 80000 + => nand write 1000000 0 80000 + +Firmware ucode location +--------------------------------- +Microcode(ucode) to FMAN's IRAM is needed to make FMAN Ethernet work. +u-boot loads ucode FLASH. The location for ucode: +NOR Flash: 0xfe000000 +NAND Flash: 0x1f00000 + +Using the Device Tree Source File +--------------------------------- +To create the DTB (Device Tree Binary) image file, +use a command similar to this: + + dtc -b 0 -f -I dts -O dtb p1023rds.dts > p1023rds.dtb + +Likely, that .dts file will come from here; + + linux-2.6/arch/powerpc/boot/dts/p1023rds.dts +or + make p1023rds.dtb ARCH=powerpc +in linux-2.6 directory. + +Booting Linux +------------- +Place a linux uImage in the TFTP disk area. + + tftp 1000000 uImage + tftp 2000000 rootfs.ext2.gz.uboot + tftp c00000 p1023rds.dtb + bootm 1000000 2000000 c00000 diff --git a/board/freescale/p1_p2_rdb/README b/board/freescale/p1_p2_rdb/README new file mode 100644 index 0000000000..cb664a5bd7 --- /dev/null +++ b/board/freescale/p1_p2_rdb/README @@ -0,0 +1,145 @@ +Overview +-------- +P2020RDB is a Low End Dual core platform supporting the P2020 processor +of QorIQ series. P2020 is an e500 based dual core SOC. + +Building U-boot +----------- +To build the u-boot for P2020RDB: + make P2020RDB_config + make + +NOR Flash Banks +----------- +RDB board for P2020 has two flash banks. They are both present on boot. + +Booting by default is always from the boot bank at 0xef00_0000. + +Memory Map +---------- +0xef00_0000 - 0xef7f_ffff Alternate bank 8MB +0xe800_0000 - 0xefff_ffff Boot bank 8MB + +0xef78_0000 - 0xef7f_ffff Alternate u-boot address 512KB +0xeff8_0000 - 0xefff_ffff Boot u-boot address 512KB + +Switch settings to boot from the NOR flash banks +------------------------------------------------ +SW4[8]=0 default NOR Flash bank +SW4[8]=1 Alternate NOR Flash bank + +Flashing Images +--------------- +To place a new u-boot image in the alternate flash bank and then boot +with that new image temporarily, use this: + tftp 1000000 u-boot.bin + erase ef780000 ef7fffff + cp.b 1000000 ef780000 80000 + +Now to boot from the alternate bank change the SW4[8] from 0 to 1. + +To program the image in the boot flash bank: + tftp 1000000 u-boot.bin + protect off all + erase eff80000 ffffffff + cp.b 1000000 eff80000 80000 + +Using the Device Tree Source File +--------------------------------- +To create the DTB (Device Tree Binary) image file, +use a command similar to this: + + dtc -b 0 -f -I dts -O dtb p2020rdb.dts > p2020rdb.dtb + +Likely, that .dts file will come from here; + + linux-2.6/arch/powerpc/boot/dts/p2020rdb.dts + +Booting Linux +------------- +Place a linux uImage in the TFTP disk area. + + tftp 1000000 uImage.p2020rdb + tftp 2000000 rootfs.ext2.gz.uboot + tftp c00000 p2020rdb.dtb + bootm 1000000 2000000 c00000 + +Implementing AMP(Asymmetric MultiProcessing) +--------------------------------------------- +1. Build kernel image for core0: + + a. $ make 85xx/p1_p2_rdb_defconfig + + b. $ make menuconfig + - un-select "Processor support"-> + "Symetric multi-processing support" + + c. $ make uImage + + d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core0 + +2. Build kernel image for core1: + + a. $ make 85xx/p1_p2_rdb_defconfig + + b. $ make menuconfig + - Un-select "Processor support"-> + "Symetric multi-processing support" + - Select "Advanced setup" -> + "Prompt for advanced kernel configuration options" + - Select + "Set physical address where the kernel is loaded" + and set it to 0x20000000, assuming core1 will + start from 512MB. + - Select "Set custom page offset address" + - Select "Set custom kernel base address" + - Select "Set maximum low memory" + - "Exit" and save the selection. + + c. $ make uImage + + d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core1 + +3. Create dtb for core0: + + $ dtc -I dts -O dtb -f -b 0 + arch/powerpc/boot/dts/p2020rdb_camp_core0.dts > + /tftpboot/p2020rdb_camp_core0.dtb + +4. Create dtb for core1: + + $ dtc -I dts -O dtb -f -b 1 + arch/powerpc/boot/dts/p2020rdb_camp_core1.dts > + /tftpboot/p2020rdb_camp_core1.dtb + +5. Bring up two cores separately: + + a. Power on the board, under u-boot prompt: + => setenv + => setenv + => setenv bootargs root=/dev/ram rw console=ttyS0,115200 + b. Bring up core1's kernel first: + => setenv bootm_low 0x20000000 + => setenv bootm_size 0x10000000 + => tftp 21000000 uImage.core1 + => tftp 22000000 ramdiskfile + => tftp 20c00000 p2020rdb_camp_core1.dtb + => interrupts off + => bootm start 21000000 22000000 20c00000 + => bootm loados + => bootm ramdisk + => bootm fdt + => fdt boardsetup + => fdt chosen $initrd_start $initrd_end + => bootm prep + => cpu 1 release $bootm_low - $fdtaddr - + c. Bring up core0's kernel(on the same u-boot console): + => setenv bootm_low 0 + => setenv bootm_size 0x20000000 + => tftp 1000000 uImage.core0 + => tftp 2000000 ramdiskfile + => tftp c00000 p2020rdb_camp_core0.dtb + => bootm 1000000 2000000 c00000 + +Please note only core0 will run u-boot, core1 starts kernel directly +after "cpu release" command is issued. diff --git a/board/freescale/p1_p2_rdb_pc/README b/board/freescale/p1_p2_rdb_pc/README new file mode 100644 index 0000000000..44377317dd --- /dev/null +++ b/board/freescale/p1_p2_rdb_pc/README @@ -0,0 +1,46 @@ +Overview +-------- +P1_P2_RDB_PC represents a set of boards including + P1020MSBG-PC + P1020RDB-PC + P1020UTM-PC + P1021RDB-PC + P1024RDB + P1025RDB + P2020RDB-PC + +They have similar design of P1020RDB but have DDR3 instead of DDR2. P2020RDB-PC +has 64-bit DDR. All others have 32-bit DDR. + +Key features on these boards include: + * DDR3 + * NOR flash + * NAND flash (on RDB's only) + * SPI flash (on RDB's only) + * SDHC/MMC card slot + * VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB) + * PCIE slot and mini-PCIE slots + +As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM +is used to store SPD data. In case of absent or corrupted SPD, falling back +to timing data embedded in the source code will be used. Raw timing data is +extracted from DDR chip datasheet. Different speeds of DDR are supported with +this approach. ODT option is forced to fit this set of boards, again because +they don't have regular DIMMs. + +CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet specification +for writing timing. + +VSC firmware Address is defined by default in config file for eTSEC1. + +SD width is based off DIP switch. DIP switch is detected on the +board by reading i2c bus and setting the appropriate mux values. + +Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC have +pins multiplexing. QE function needs to be disabled to access Nor Flash and +CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe" +in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to +enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below + +'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD. +'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD. diff --git a/board/freescale/p2041rdb/README b/board/freescale/p2041rdb/README new file mode 100644 index 0000000000..292d0d39cf --- /dev/null +++ b/board/freescale/p2041rdb/README @@ -0,0 +1,123 @@ +Overview +========= +The P2041 Processor combines four Power Architecture processor cores +with high-performance datapath acceleration architecture(DPAA), CoreNet +fabric infrastructure, as well as network and peripheral bus interfaces +required for networking, telecom/datacom, wireless infrastructure, and +military/aerospace applications. + +P2041RDB board is a quad core platform supporting the P2041 processor +of QorIQ DPAA series. + +Boot from NOR flash +=================== +1. Build image + make P2041RDB_config + make all + +2. Program image + => tftp 1000000 u-boot.bin + => protect off all + => erase eff80000 efffffff + => cp.b 1000000 eff80000 80000 + +3. Program RCW + => tftp 1000000 rcw.bin + => protect off all + => erase e8000000 e801ffff + => cp.b 1000000 e8000000 50 + +4. Program FMAN Firmware ucode + => tftp 1000000 ucode.bin + => protect off all + => erase ef000000 ef0fffff + => cp.b 1000000 ef000000 2000 + +5. Change DIP-switch + SW1[1-5] = 10110 + Note: 1 stands for 'on', 0 stands for 'off' + +Boot from SDCard +=================== +1. Build image + make P2041RDB_SDCARD_config + make all + +2. Generate PBL imge + Use PE tool to produce a image used to be programed to + SDCard which contains RCW and U-Boot image. + +3. Program the PBL image to SDCard + => tftp 1000000 pbl_sd.bin + => mmcinfo + => mmc write 1000000 8 441 + +4. Program FMAN Firmware ucode + => tftp 1000000 ucode.bin + => mmc write 1000000 46a 10 + +5. Change DIP-switch + SW1[1-5] = 01100 + Note: 1 stands for 'on', 0 stands for 'off' + +Boot from SPI flash +=================== +1. Build image + make P2041RDB_SPIFLASH_config + make all + +2. Generate PBL imge + Use PE tool to produce a image used to be programed to + SPI flash which contains RCW and U-Boot image. + +3. Program the PBL image to SPI flash + => tftp 1000000 pbl_spi.bin + => spi probe 0 + => sf erase 0 100000 + => sf write 1000000 0 $filesize + +4. Program FMAN Firmware ucode + => tftp 1000000 ucode.bin + => sf erase 110000 10000 + => sf write 1000000 110000 $filesize + +5. Change DIP-switch + SW1[1-5] = 10100 + Note: 1 stands for 'on', 0 stands for 'off' + +CPLD command +============ +The CPLD is used to control the power sequence and some serdes lane +mux function. + +cpld reset - hard reset to default bank +cpld reset altbank - reset to alternate bank +cpld lane_mux - set multiplexed lane pin + lane 6: 0 -> slot1 (Default) + 1 -> SGMII + lane a: 0 -> slot2 (Default) + 1 -> AURORA + lane c: 0 -> slot2 (Default) + 1 -> SATA0 + lane d: 0 -> slot2 (Default) + 1 -> SATA1 + +Using the Device Tree Source File +================================= +To create the DTB (Device Tree Binary) image file, use a command +similar to this: + dtc -O dtb -b 0 -p 1024 p2041rdb.dts > p2041rdb.dtb + +Or use the following command: + {linux-2.6}/make p2041rdb.dtb ARCH=powerpc + +then the dtb file will be generated under the following directory: + {linux-2.6}/arch/powerpc/boot/p2041rdb.dtb + +Booting Linux +============= +Place a linux uImage in the TFTP disk area. + tftp 1000000 uImage + tftp 2000000 rootfs.ext2.gz.uboot + tftp 3000000 p2041rdb.dtb + bootm 1000000 2000000 3000000 diff --git a/board/freescale/p3060qds/README b/board/freescale/p3060qds/README new file mode 100644 index 0000000000..ec627980c1 --- /dev/null +++ b/board/freescale/p3060qds/README @@ -0,0 +1,110 @@ +Overview +========= +The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC. + +The P3060 Processor combines six e500mc Power Architecture processor +cores(1.2GHz) with high-performance datapath acceleration +architecture(DPAA), CoreNet fabric infrastructure, as well as network +and peripheral bus interfaces required for networking, telecom/datacom, +wireless infrastructure, and military/aerospace applications. + + +P3060QDS Board Specifications: +============================== +Memory subsystem: + * 2G Bytes UDIMM DDR3(64bit bus) with ECC on + * 128M Bytes NOR flash single-chip memory + * 16M Bytes SPI flash + * 8K Bytes AT24C64 I2C EEPROM for RCW + +Ethernet(Default SERDES 0x19): + * FM1-dTSEC1: connected to RGMII PHY1 (Vitesse VSC8641 on board,Bottom of dual RJ45) + * FM1-dTSEC2: connected to RGMII PHY2 (Vitesse VSC8641 on board,Top of dual RJ45) + * FM1-dTSEC3: connected to SGMII PHY (Vitesse VSC8234 port1 in slot1) + * FM1-dTSEC4: connected to SGMII PHY (Vitesse VSC8234 port3 in slot1) + * FM2-dTSEC1: connected to SGMII PHY (Vitesse VSC8234 port0 in slot2) + * FM2-dTSEC2: connected to SGMII PHY (Vitesse VSC8234 port2 in slot2) + * FM2-dTSEC3: connected to SGMII PHY (Vitesse VSC8234 port0 in slot1) + * FM2-dTSEC4: connected to SGMII PHY (Vitesse VSC8234 port2 in slot1) + +PCIe: + * PCIe1: Lanes A, B, C and D of Bank1 are connected to one x4 PCIe SLOT4 + * PCIe2: Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT3 + +RapidIO: + * sRIO1: Lanes E, F, G and H of Bank1 are connected to sRIO1 (SLOT3) + * sRIO2: Lanes A, B, C and D of Bank1 are connected to sRIO2 (SLOT4) + +USB: + * USB1: connected via an external ULPI PHY SMC3315 to a TYPE-A interface + * USB2: connected via an external ULPI PHY SMC3315 to a TYPE-AB interface + +I2C: + * I2C1_CH0: EEPROM AT24C64(0x50) RCW, AT24C02(0x51) DDR SPD, + AT24C02(0x53) DDR SPD, AT24C02(0x57) SystemID, RTC DS3232(0x68) + * I2C1_CH1: 1588 RiserCard(0x55), HSLB Testport, TempMon + ADT7461(0x4C), SerDesMux DS64MB201(0x51/59/5C/5D) + * I2C1_CH2: VDD/GVDD/GIDD ZL6100 (0x21/0x22/0x23/0x24/0x40) + * I2C1_CH3: OCM CFG AT24C02(0x55), OCM IPL AT24C64(0x56) + * I2C1_CH4: PCIe SLOT1 + * I2C1_CH5: PCIe SLOT2 + * I2C1_CH6: PCIe SLOT3 + * I2C1_CH7: PCIe SLOT4 + * I2C2: NULL + * I2C3: NULL + +UART: + * Supports two UARTs up to 115200 bps for console + + +Boot from NOR flash +=================== +1. Build image + export ARCH=powerpc + export CROSS_COMPILE=/your_path/gcc-4.5.xx-eglibc-2.11.xx/powerpc-linux-gnu/bin/powerpc-linux-gnu- + make P3060QDS_config + make + +2. Program image + => tftp 1000000 u-boot.bin + => protect off all + => erase eff80000 efffffff + => cp.b 1000000 eff80000 80000 + +3. Program RCW + => tftp 1000000 rcw.bin + => protect off all + => erase e8000000 e801ffff + => cp.b 1000000 e8000000 50 + +4. Program FMAN Firmware ucode + => tftp 1000000 ucode.bin + => protect off all + => erase ef000000 ef0fffff + => cp.b 1000000 ef000000 2000 + +5. Change DIP-switch + RCW Location: SW1[1-5] = 01101 (eLBC 16bit NOR flash) + Note: 1 stands for 'on', 0 stands for 'off' + + +Using the Device Tree Source File +================================= +To create the DTB (Device Tree Binary) image file, use a command +similar to this: + dtc -O dtb -b 0 -p 1024 p3060qds.dts > p3060qds.dtb + +Or use the following command: + {linux-2.6}/make p3060qds.dtb ARCH=powerpc + +then the dtb file will be generated under the following directory: + {linux-2.6}/arch/powerpc/boot/p3060qds.dtb + + +Booting Linux +============= +Place a linux uImage in the TFTP disk area. + tftp 1000000 uImage + tftp 2000000 rootfs.ext2.gz.uboot + tftp 3000000 p3060rdb.dtb + bootm 1000000 2000000 3000000 -- cgit v1.2.1